Search Documents

The Barrick North Mara Mine and the Advanced Systems Group at SGS Minerals collaborated on the implementation of a grinding expert system for the control and optimisation of a single semi autogenous (SAG) mill. Over the last 5 years, grinding expert control has gained wide acceptance by mineral processors. In this paper, two key factors for success are highlighted: the adaptability of the software tools and the interaction with site personnel. Created with SGS?s MET expert console (MEC) toolkit, and running on Gensym?s G2 real time inference software, the North Mara expert logic has been set up to keep a steady and on spec leaching feed slurry while striving to maximize throughput. Leach feed stability was achieved by standardizing operating practices across shifts; a result of successful collaboration with site personnel in developing a consistent control strategy. The strategy maintains the SAG load and power draw in an optimised range by manipulating SAG feed rates and inlet water flow. The project life-cycle was slightly longer than average due to site specific constraints. One of these was the high turnover rate of site?s workforce during the project, coupled with the availability of key staff on site due to the fly in fly out work roster. These constraints called for different, and innovative ways of project commissioning and hand-over. This paper describes details of the control solution, its implementation as well as results and conclusions.

Jan 1, 2009

By F. H. Guise-Brown

Raise-boring experiences in the gold mines of the Anglo American Corporation Group by J. W. WILSON and P. C. GRAHAM Published in the Journal, October, 1972. Discussion by F. H. Guise-Brown., B.Sc. (Min. Eng.) (Member) INTRODUCTION Messrs J. W. Wilson and P. C. Graham are to be congratulated on an excellent paper containing several thought-provoking remarks. The concept of allocating a machine and equipment valued initially at some R300 000 on an experimental basis is courageous, and the results obtained could be of interest to the mining industry as a whole. The Gold Fields of S.A. Group approached this problem differently. In pioneering the start of this work in South African gold mines, they considered that expenditure of this magnitude would be warranted only if the proposition was viable right from the start. To this end, a Robbins R41 was purchased expressly to assist in the duplication of part of the No. 1 shaft system of the Doomfontein Gold Mine. Mr M. J. Koortsl has summed up the initial results of this work and given some preliminary costing, but inflation since that period has made these figures somewhat out of date.

Jan 10, 1972

By J. J. Taute, G. Chisakuta, P. Bwando, G. Mitshabu

"BASF Mining Solutions have developed a new generation of copper solvent-extraction reagents that offer significant benefits over the existing reagents available to the industry today. Initial laboratory studies and pilot-plant trials have shown that these new reagents offer the benefits of a dramatic increase in resistance to degradation and are nitration-proof. This paper details a recent pilot-plant campaign at a commercial solvent-extraction plant. The main focus was to evaluate the copper/iron selectivity, copper recovery and net transfer of the new reagent compared with the conventional oxime reagents. The new reagent displays similar copper recovery and net transfer capabilities from typical agitation leach solutions. The pilot-plant results show a step change improvement in copper/iron selectivity in comparison with the existing modified and non-modified hydroxyoxime reagents used on the commercial plant. INTRODUCTION Copper solvent extraction (SX) from an acidic aqueous solution is typically accomplished using a hydroxyoxime extractant (Jergensen, 1999; Kordosky, 2000; Szymanowski, 1993). There are three hydroxyoximes from which all standard formulations are derived: 5-nonyl salicylaldoxime (NSAO), 5-dodecyl salicylaldoxime (DSAO) and 2-hydroxy-5-nonyl acetophenone oxime (HNAO). In the case of NSAO, it is necessary to use equilibrium modifiers in order to increase the copper stripped from the extractant (Kordosky & Virnig, 2003). Blends of DSAO, NSAO and HNAO are used to cover a wide spectrum of conditions (Kordosky, 2008). Use of modified aldoximes and reagent blends over the last 30 years has influenced the way copper producers and equipment manufacturers have approached the operation of copper plants. Existing solvent-extraction reagents cater for typical pregnant leach solutions (PLS) of copper mining systems which do not have significant effects on the reagent. Table I illustrates the range of copper concentration, pH values, temperature and iron concentrations for different leaching operations. As conditions become increasingly aggressive (i.e., higher PLS temperatures in primary sulfide leach or high iron content), current reagents become less capable of functioning according to expectations. One example is the effect of high iron (Fe3+) concentration in PLS and operating SX to achieve high copper recoveries. The ferric is partially chemically extracted and is transferred to elctrowinning (EW) during the stripping stage. To avoid a build-up of iron in electrolyte, which negatively affects current efficiency, a bleed of electrolyte is required. This bleed leads to excessive consumption of reagents, such as cobalt added to the EW process, and thus increases operational cost."

Jan 1, 2015

By Kedikilwe Oageng

Effective perimeter control during drilling and blasting is critical not only to blasting results but also to the overall stability of the pit over its entire life span. A pit where perimeter control is not given enough attention when conducting drilling and blasting operations, often experiences over-break or back break beyond final pit wall limits, and therefore has a relatively high probability of failure. Such a pit also becomes unsafe, sometimes not easily accessible, has increased loading costs due to production of oversize, longer cycle times and often problems are encountered when blasting subsequent benches. All these are undesirable consequences, which have negative cost implications. Specialised blasting techniques such as trim blasting and pre-splitting have over the years proved to be effective perimeter control measures. However, the success of these techniques is directly attributable to the time and effort given to the processes. This paper presents results of a project undertaken to monitor, review and optimize the trim blasting and pre-splitting processes at Orapa Diamond Mine in Botswana. The project was specifically incepted to improve the final wall conditions, which continued to deteriorate due to persistent over-break during blasting. The paper also analyses the results obtained against a benchmark of results taken prior to project implementation. Specific blast design parameters which are critical to blasting results were identified as problem areas after auditing of the pre-implementation drilling and blasting practices. These include drill-hole depth, spacing, splitting factor for pre-splits and timing of trim blasts. The impact of different rock types on the results was also studied, and recommendations were made at different phases of the project and results obtained after implementation analysed until optimum results were achieved.

Jan 1, 2008

Mill relining is a major contributor to overall plant downtime. Reducing the number of mill liner pieces removed from and replaced in the mill has a direct impact on the overall reline time and in turn, mill availability. To improve the mill availability of Ridgeway Operations' 32 foot SAG mill, a number of initiatives were implemented in terms of liner design. These included the conversion of the shell from 40 to 30 rows, reducing the number of pieces from 80 to 60 each shell reline and reducing the number of pieces from 48 to 32 per feed end reline. In addition, modifications were made to the discharge end of the mill to extend the life of the outer pulp lifter and discharge cone, thereby reducing the frequency of change out. The standard radial outer pulp lifter was converted to an angled design. The discharge cone was converted to the BullnoseTM design supplied by Bradken. This paper discusses the design changes made and the expected benefits to the Ridgeway Operations in terms of mill availability improvements.

Jan 1, 2007

By Thermo Electron, Tim Sennett

Summary ?SamStat Development ?SamStat Description ?Accuracy ?Availability ?Cost of ownership ?Capital ?Installation ?Operating/Maintenance ?Case Studies ?Modikwa ?Combined concentrate sampling ?Cerro Verde ?State of the art sampling & analysis ?Ok Tedi Final Tails ?brownfields installation ?Conclusion

Jan 1, 2005

By A. V. Z. Brink

This paper describes the development of a monitoring architecture that allows for continuous monitoring of the process of mining, the underground environment, the state of the rockmass and its response to mining. The system is based on an open standard and is non-propriety. It allows for dense sensor arrays in the workplace, wire less communication to the closest power line, and TCP/IP communication to a central server. Continuous monitoring and quantification of the appropriate parameters allows a mine to optimise its mine process; to dynamically access the safety and health risk to people and equipment; and to quantify exposure to potential heath hazards such as dust, gas or noise. Current application examples of continuous monitoring include an application to optimise drilling and blasting thought fragmentation monitoring; an application of wireless sensor network-based monitoring in to provide early detection of potential rockfalls; and a trail to continuously assess the gold grade at the shaft through correlation with radioactivity. It is unlikely that a single monitored parameter will provide adequate knowledge of the assessed risk or even an optimisation approach. Multiple parameters are being combined using cognitive science tools such as Bayesian theory and other statistical methods to improve the accuracy and relevance of, for example, risk quantification. The decision maker is not confronted with massive amounts of raw data but rather with a single knowledge statement such a probability of failure, a human physiological strain index or an optimisation index.

Jan 1, 2008

By H. A. D. Kirsten

The structural competence of mesh- and fibre-reinforced shotcrete was investigated in two series of tests on full-scale panels. It was found that uniformly distributed loading was marginally less demanding than point loading, mesh reinforcement was superior to fibre reinforcement, Dramix fibre and Melt Extract fibre were similar in reinforcing characteristics, and 30 mm to 35 mm was an optimum fibre length. Furthermore, the consistency of the fibre content could not be assured on practical mining sites, and an average fibre content of about 1,5 per cent was the maximum that could be obtained for fibre lengths not exceeding 35 mm. Also, owing to its greater flexibility, shotcrete reinforced with diamond mesh was preferable to fibre-reinforced shotcrete in mining excavations subject to squeezing conditions. In view of the difficulties associated with assuring the consistency of the fibre content in mining applications, it appears that the sophisticated attributes of fibre-reinforced shotcrete can be effectively exploited only in civil-engineering applications in which quality assurance is subject to explicit contractual control. Load-deflection curves, together with measurements of compressive stresses in the surfaces of some of the panels, enabled the ultimate flexural strength of reinforced shotcrete to be rigorously formulated, and rigorous design procedures for shotcrete subject to bending and direct thrust to be developed. The application of the procedures is demonstrated in a practical design case in which the moments and thrusts in a tunnel lining are determined in a numerical analysis of the interaction between the lining, the surrounding rock, and the rock-reinforcing system.

Jan 1, 1992

Mixed integer programming (MIP) has been used for optimizing production schedules of mines since the 1960s. The major problem in the long-term production scheduling for an entire orebody is that the number of integer variables needed to formulate an MIP model is too large to solve the formulation. This number may reach well over one hundred thousand. To overcome this difficulty, this paper presents two new algorithms to reduce the size of the problem. These algorithms assign an earliest and latest possible start date for each machine placement, eliminating the integer variables that correspond to machine placement before its early start date and after its late start date. A case study based on Kiruna Mine, the second largest underground mine in the world, is summarized in the paper. It shows substantial improvement in the solution time required using the new algorithms. This increased efficiency in the solution time of the MIP model allows it to be applied to Kiruna Mine, with the potential to increase substantially the net present value (NPV) of the project.

Jan 1, 2008

By F. Samimi Namin

One of the main tasks in exploitation of mines is to select a method suitable for the deposits, specific features including geometric, geo-mechanical and geological features. The purpose of selecting a mining method at this stage is to choose one or more method(s) having the most coordination with the deposit?s conditions and external factors, including the allocated budget and local technology for detailed feasibility studies. Several methods have been developed in the past to evaluate suitable mining methods for an ore deposit, based on its physical characteristics. These approaches can be classified into three groups: (1) profile and checklist methods, (2) numerical ranking (scoring) methods, and (3) decision-making models. Most of these methods have shortcomings. Considering the fact that most of the specifications of mineral deposits, such as dip and depth, are linguistic variables, absoluteness of the explaining parameters by previous methods can be mentioned as the most important disadvantage of these methods. This paper discusses the Fuzzy technique for order performance by similarity to ideal solution (Fuzzy TOPSIS) to determine the mining method. The fuzzy decision making (FDM) software tool is employed to develop a Fuzzy TOPSIS based model. Application of this model with various values (crisp, linguistic and fuzzy) of the deposit eliminated the existing disadvantages of other methods. Two empirical illustrations demonstrate the effectiveness and feasibility of the evaluation procedure. These show that the proposed model performs better than its alternatives. Keywords: mining method selection, fuzzy TOPSIS, decision making, mining engineering, linguistic variables.

Jan 1, 2008

The Skorpion process comprises three processing steps-atmospheric leaching in sulfuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the root causes of the crud formation in the solvent extraction circuit and optimization strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica.

Jan 1, 2007

By S. Kauchali

"Underground coal gasification (UCG) is recognized as an efficient mining technique capable of chemically converting the coal from deep coal seams into synthesis gas. Depending on the main constituents of the synthesis gas, chemicals, electricity, or heat can be produced at the surface. This paper provides a high-level graphical method to assist practitioners in developing preliminary gasification processes and experimental programmes prior to detailed designs or field trials. The graphical method identifies theoretical limits of operation for sensible gasification within a thermally balanced region, based primarily on the basic coal chemistry. The analyses of the theoretical outputs are compared to actual field trials from sites in the USA and Australia, with very favourable results. A South African coal is studied to determine the possible synthesis gas outputs achievable using various UCG techniques: controlled retractable injection point (CRIP) and linked vertical wells (LVW). For CRIP techniques, an important result suggests that pyrolysis, and subsequent char production, are important intermediate phenomena allowing for increased thermal efficiencies of UCG. The conclusion is that South African coals need to be studied for pyrolysis-char behaviour as part of any future UCG programme. The results also suggest that UCG with CRIP would be a preferred technology choice for Bosjesspruit coal where pyrolysis dynamics are important. Lastly, the use of CO2 as oxidant in the gasification process is shown to produce syngas with significant higher heating value. Introduction and literature surveyCoal is a commonly utilized fossil fuel, providing over 40% of global electricity demand and about 90% of South Africa’s primary energy needs. However, less than 20% of the known world resources are suitable for possible extraction using conventional surface and underground mining techniques (Andrianopolous,, Korre, and Durucan, 2015). Underground coal gasification (UCG) has the potential to recover the energy stored in coal in an environmentally responsible manner by exploiting seams that are deemed unmineable by traditional methods. The UCG process, if successfully developed, can increase coal reserves substantially. For example, in the Limpopo region of South Africa alone, the estimated potential for UCG gas, based on existing geological records, is over 400 trillion cubic feet (TCF) natural gas equivalent – this is about a hundred times more gas than the existing 4-TCF Pande-Temane natural gas field reserve in Mozambique (de Pontes, Mocumbi, and Sangweni, 2014)."

Oct 1, 2018

By A. A. Bradley, P. J. D. Lloyd, A. J. Freemantle

Developments in centrifugal milling by A. A. BRADLEY,B.Sc. (Rhodes) (Visitor), A. J. FREEMANTLE, B.Sc. Hons. (Wits) (Visitor), and P. J. D. LLOYD, B.Sc. (Chem. Eng.), Ph.D. (Cape) (Fellow) The theoretical and experimental results of a study of centrifugalmills are reviewed. Means for the scaling up of such mills are suggested, and tests on a prototype mill are described. Despite the high lining wear in the centrifugal machine, which reduces its productive availability, its other advantages suggest that there is merit in pursuing its further development.

Jan 6, 1974

By H. E. Bartlett

Previously, the grade of ore at the shaft head was taken to be equivalent to the grade measured in the faces by means of chip sampling. The tonnage mined from the stopes is determined from survey volumetric measurements. Estimates of shaft head grade and tons include the grades and tons of waste, development ore, sweepings from old areas, and other sources, not all of which are sampled. The tonnage of ore delivered at the shaft is often estimated using skip factors. These factors are subject to manipulation and not all the skips are filled to the same level. Consequently, both the grade and tonnage of ore delivered at shaft head are subject to a measure of uncertainty. For many years, these uncertainties have led to disputes between shaft managers and metallurgists over the reconciliation between shaft tons and grade and plant tons and grade. These problems are compounded when several shafts feed a central processing plant. Shaft bonuses and a shaft?s profitability are affected by poor gold allocation methods. Without measurement of the grade and tonnage from all shafts, a poorly performing shaft could benefit at the expense of the other shafts. In order to improve the measurement of grades and tonnage at the shaft head, which is the custody transfer point between the mine and surface operations, South African mining companies have developed a methodology to measure the mass of ore from each shaft using rail weighing equipment, and the run-of-mine grades delivered from each shaft using cross-stream (go-belt) sampling. Harmony Gold Mining Company has implemented the rail weighing and go-belt sampling methods for their shafts. This paper deals with the statistical tests on the procedures and control measures that are in place to establish confidence in the gold allocations. The metal accounting system for examining the allocations follows the first principle of the AMIRA P754 Metal Accounting Code of Practice namely ?The metal accounting system must be based on accurate measurements of mass and metal content. It must be based on a full check-in check-out system?. The check-in is mass and grade of run-of-mine ore and the check-outs are the plant input grades and the recovery and residue from the plant. The balances between check-in and check-out are the subject of the statistical analyses, which have been conducted using the classical statistical tests and procedures that are generally used in all fields of endeavour. It is concluded that the gold allocation procedures that rely on go-belt sampling and rail weighing of ore from shafts has been successfully implemented, and that the system, which has been in operation at Harmony since 1993, has won general acceptance from stakeholders, with the gold allocations being perceived as being fair to all. Apart from the on-mine issues of bonuses and fair allocations, accurate metal accounting assists in the broader issues of generating accurate production figures for management. An added benefit of weighing and sampling ore at the shaft head has been that shafts now have daily moving average grades, which are used for grade control. The go-belt sample at the shaft head is the first accurate sample of production in the value chain from face sampling to gold bullion. Keywords metal accounting, go-belt sampling, run-of-mine sampling, codes of practice, AMIRA P754, train weighing, statistical analysis, gold split, allocation of gold, metal balance, grade control.

Jan 1, 2014

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

The vast majority of the roughly 100 million rock anchors installed in mines in the USA each year use resin cartridges1. About 4.5 million of these bolts are installed using a mechanical shell in addition to the resin to create an active (pre-tensioned) bolt. Over 1 million of the bolts are passive cable bolts and typically have an effective grout length of 1.2 m, regardless of the cable length, which could be as long as 6 m. The successful performance of the resin grouted bolts depends on several parameters, including the annular gap between the bolt and hole wall, which should be relatively small, ideally from 3 mm to 5 mm. This requirement, combined with the high viscosity of the resin, produces a high back-pressure that can cause the bolt being installed to buckle or not be installed to standard. It is this back-pressure that limits the effective grout length with passive cable bolts and causes the mechanically anchored bolt failures (typically called ?spinners? where the mechanical shell does not anchor). This creates potentially unsafe conditions and wastes time and money. A purpose, built rig was used to mimic underground installations and record the back-pressures during full scale applications in the laboratory. This information was used, and is still being used, to reduce the failures and sub-standard installations by producing improved designs. In addition, a flow model was calibrated that can act qualitatively to estimate the back-pressures and can be used as a crude screening process before full scale prototypes are built and tested. To date, the results obtained have been used to stop the use of a mechanical shell due to the proven higher rate of failures. A new, improved mechanical shell is being field tested and another system is underdevelopment. The use of the rig is therefore ongoing to develop improved mechanical anchor systems. It is too early for real data; however, anecdotal evidence seems to indicate that significant improvements can and will be made.

Jan 1, 2011

By B. K. Cross

This paper, which adopts a philosophical approach, attempts to analyse the contribution that the computer is capable of making in geological analysis, financial evaluation, and mine project control. Also examined are some reasons for non-utilization of these capabilities. As with most computer associated problems, the cause is primarily human and not mechanical. The paper gives one numerical example of the analysis of geological data and one of the evaluation of mine-design data. The values used in the examples are intended only to emphasize certain points and are not necessarily reproducible.

Jan 1, 1980

By S. Tu, Y. Yuan, H. Wei, Z. Chen, M. Jia

"To reduce production costs and increase efficiency in ageing coal mines, a system that utilizes two shearers in a fully mechanized longwall working face is proposed. Using theoretical and engineering experience, three issues pertaining to the system were determined: (a) the two-shearer mining technique; (b) matching and modifying the equipment; (c) and coal-cutting task allocation for each shearer. Two mining processes are proposed, with the two shearers travelling in either the same or opposing directions. To avoid breakage of chains and pan extrusion of the armoured face conveyor (AFC), the length of the AFC ‘snake’ was controlled. To ensure continuous cutting and transporting of coal, the cross-sectional dimensions of the AFC were checked and the shearer closer to the head drive was modified. Based on the assumption of equal cutting times for each shearer, the meeting position of the two shearers was obtained by using a theoretical model of mining task allocation. Application of this technique at No. 2 Jining Mine, China, has shown remarkable benefits: daily production capacity was increased by 54% and personnel efficiency was improved by 33 t/d per person. IntroductionAll coal mines aim to increase the unit output of the working face to reduce mining costs and improve the economic efficiency of the operation. To achieve this goal, a production model known as one mining face of the mining area has been adopted by most Chinese coal mines (Hu, Meng, and Zhu, 2008; Zhang, Zhang, and Wang, 2000). Under these conditions, the main technical approaches to maximize the output are increasing the width of the working face (Qu, Xu, and Xue, 2009) and accelerating the advancing speed (Robbins, 2000). In coalfields with shallow seams, the width of a fully mechanized face exceeds 300 m (Ju and Zhu, 2015; Fu, Song, and Xing, 2010); in coalfields with deep seams, the width of the face is usually greater than 240 m (Liu et al., 2016; Li et al., 2013). The term ‘super-long working face’ was proposed to describe working faces with a width of over 240 m (Zhao and Song, 2016; Xu et al, 2007) in China. To support these long working faces with rapid advancing speeds, high-powered mining equipment is required (Kulshreshtha and Parikh, 2001, 2002; Tu et al., 2009; Mishra, Sugla,and Singha, 2013). This is easily achieved in newly built mines, but is not a good choice for ageing mines because of the low return on a high investment on account of the limited remaining resources. It is therefore difficult for ageing mines to significantly increase their unit output with the existing mining equipment. This study focused on this problem: two shearers were applied to a longwall fully mechanized working face (LFMWF) to achieve increased unit output."

Oct 1, 2018

By W. Newcomen, D. Brox

The assessment of the stability performance of open pit highwalls has traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work has been reviewed and are endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on relatively consistent trends in highwall strain data. L’évaluation du niveau de stabilité des hauts murs de carrières a traditionnellement été basée sur les taux de mouvements de surfaces. Bien que cette approche soit généralement acceptée à travers l’industrie, elle présente des défis pour la définition de seuils appropriés concernant la sécurité des opérations minières et n’adresse pas la notion de déformations totales. Des données de mouvements de surface provenant d’un nombre limité d’opérations minières à ciel ouvert d’Amérique du Nord et du Sud ont été évaluées en terme de déformation des hauts murs, de qualité de la masse rocheuse et des mécanismes inférés d’instabilité. Des seuils de déformation pour différentes phases clefs de stabilité de hauts murs ont été revus et sont endossés, basé sur l'évaluation de donnés additionnelles. Un critère de déformation empirique pour l’évaluation de la stabilité des hauts murs est postulé, basé sur des tendances relativement consistantes de données de déformations de hauts murs. Die Beurteilung der Stabilität von hohen Felsböschungen basiert traditionellerweise von Oberflächenbewegungen. Obwohl dieses Verfahren im Allgemeinen akzeptiert wird, stellt es jedoch gewisse Probleme für die Festlegung von Grenzwerten für die Sicherheit dar. Die totalen Dehnungen werden bei dieser Betrachtungsweise vernachlässigt. Eine beschränkte Anzahl von Oberflächenbewegungs Daten von Bergbauwerke in Nord- und Südamerika sind in Bezug auf die Dehnungen von hohen Felsböschungen, Felsqualität und davon abgeleiteten Bruchmechanismen untersucht worden. Grenzwerte für die Belastung von hohen Felsböschungen während den massgebenden Bauetappen aus bisherigen Projekten sind begutachtet und durch zusätzliche Untersuchungen bestätigt worden. Gestützt auf relativ konsitenten Trends, ist hier ein empirisches Verfahren der Dehnungen in hohen Felsböschungen zur Beurteilung der Stabilität vorgestellt.

Jan 1, 2003

By Karl-Heinz Obst, Juergen Stradtman

The importance of the chemical and physical properties of lime has been overlooked for years although the quality of lime plays an important role in the production of steel. With the introduction of the oxygen injection process these properties have been re-evaluated. The CaO, MgO, S, and P2O5 contents of lime are important, but so are the physical properties such as granulation, reactivity with respect to slag formation, and the degree of burning. Soft burnt lime enhances de-phosphorisation and de-sulphurisation, and facilitates the smelting process in general, mainly due to its large specific surface. Special lime, prepared as briquettes from quicklime and fluxes or as pellets from limestone and various fluxes with or without binding agents, clearly accelerates lime dissolution during the slag formation process, lowers the melting point, and enhances de-phosphorisation, de-sulphurisatlon, and de-carburisation even more than soft burnt lime. The introduction of special limes in the oxygen injection process for steel production has opened up new fields for commercial exploitation of slags as well as improved operational techniques.