Search Documents

By Thornton L. Neathery

Geologic investigation of a mineralized zone in eastern Alabama indicates that large quantities of talc and soapstone are scattered over a wide area close to the surface. Laboratory experiments show that this material may be upgraded to a high-quality talc. A market survey indicates that the talc deposits may be of current and long-range interest. The anthophyllite asbestos which is associated with the talc does not appear to occur in sufficient quantities to be considered as a primary commercial source.

Jan 1, 1967

By R. W. Barnes

This circular presents results of a survey conducted by the Bureau of Mines to ascertain the extent to which dust-control practices are employed in the coal-mining industry. This survey was initiated because of increasing realization of the possible harmful effects of the inhalation of dust upon the health of coal-mine workers and the advent, during recent years, of new types of mining machinery and new mining methods that may have a direct effect upon the extent of exposure to airborne dust experienced by persons mining coal. Anthracite Mines The survey covered 169 anthracite mines that were operating from November 1, 1953, to July 1, 1954. It showed that large mines employing more than 100 men were doing most to control dust produced during mining.

Jan 1, 1956

Research personnel from the Bureau of Mines, representatives of the Mining Enforcement and Safety Administration (MESA), and members of the mining industry met with other Government and Industry representatives at three seminars held in Pittsburgh, Pa., November 4, 1975; St. Louis, Mo., November 6, 1975; and Denver, Colo., November L1, 1975, to discuss the results of Bureau-sponsored research on coal mine illumination. The program, aimed at developing suitable illumination systems fur the working; places of underground coal mines, covered hardware development and field evaluation and the status of proposed MESA standards and proposed MESA enforcement procedures. These proceedings contain the opening remarks to the seminars and eight technical presentations an various aspects of coal mine illumination.

Jan 1, 1976

The works recorded in this Test Report have been performed by Rade Roncar - Electrotechnical Institute of Zagreb, SFR Yugoslavia in collaboration with Bureau of Mines. The main objective of these investigations was to investigate the possibility of fabrication of thin-walled square enclosures of satisfactory safety factor in accordance with requirements of effective technical regulations. The results and the investigations can be divided in three main fields: - investigations of thin-walled enclosures with the view of determination of pressures causing technological deformations before performing tests in accordance with effective applicable regulations, - finding the safety factor by means of tests of metal-foam pressure vents, - comparison of enclosures with and without pretreatment by technological deformation.

Jan 1, 1987

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By J. P. Capp

The Bureau of Mines conducted field-scale experiments in underground gasification of coal with oxygen-enriched air. A path about 140 feet long was linked at the rate of LO feet per day through a coalbed hydraulically fractured with a mixture of starch gel and sand. During the best gasification period, which extended for 2-1/2 days, 785,000 std. c.f. per day of 124-B.t.u. gas was produced. In other periods the heating value at times was almost 300 B.t.u. per std, c.f,, but sustained production of such gas was not achieved. During gasification, a total of 50 tons of coal was gasified and 114 tons of coal was carbonized. Approximately 12 million B, t .u. per foot of nominal path was recovered at the surface.

Jan 1, 1962

This Bureau of Mines report concerns two subjects important in the application of electric power in mining systems. Electrical transients and their suppression are discussed, and several considerations are explored with regard to the use of explosionproof or other electrical enclosures.

Jan 1, 1979

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

This report includes a short history of uranium and its uses, mineralogy of common uranium minerals, and information on the use of electronic prospecting equipment and tests for detecting the presence of uranium. Details are given on geologically favorable areas and formations and practical methods of prospecting. Some information is given on the staking of claims, what lands are open to prospecting, and methods of securing mining rights. A forecast of the economic outlook for uranium is included. Appendixes give sources of additional information and a list of libraries where unclassified Atomic Energy Commission reports may be consulted. Because the increasing use of uranium by industry has revived interest in prospecting and exploration for this element, the Bureau of Mines has issued this report, which brings up to date and expands the subject matter of a hand- book on uranium exploration and production published in 1956.l

Jan 1, 1968

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the mid funding level program plan.

Jan 1, 1980

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960

By J. R. Hoskins

This is the final report for Research Contract No. 00101300 (Min. 34) granted by the U.S. Bureau of Mines to the University of Idaho Mining Research Bureau. The research project is entitled "Development of Improved Ventilation Technology for Non-coal Mines and Other Underground Excavations.' The duration of the project was six calendar months, from 16 April to 16 October 1970. The budgeted cost was $34,867.00 of which $31,953.00 was to be furnished by the U.S. Bureau of Mines. The sequence of reporting that follows is to state the objectives as contracted, outline the program of investigation, highlight briefly the important technological factors peculiar to vein-type metal mine ventilation, and describe the normal methods of control. This is followed by the results achieved by the survey, and an itemization of the observed deficiencies in current technology. There follows a section dealing with the adopted Federal Regulations.

Jan 1, 1970

By L. R. Stark

Two wetland simulation experiments were carried out in order to determine the effects on manganese retention of several wetland design parameters, including flow rate, inlet pH, carbon supplementation, substrate type, and surface free water depth. The primary aim in each experiment was to determine if sustained manganese retention could be accomplished under the specific experimental treatments. If successful, these experiments could recommend design parameters for the construction of field wetland systems for manganese treatment. Crushed limestone clearly was superior to spent mushroom compost with respect to manganese retention. The presence of free surface water detracted from manganese treatment, while lower flow rates enhanced manganese treatment. Sustained manganese retention was achieved using crushed limestone as the substrate coupled with an absence of surface free water, under inlet water conditions of pH 7.0 and no appreciable iron. Sustained manganese retention was not achieved under reducing conditions using spent mushroom compost while varying flow rate, inlet pH, and carbon supplementation regimes. However, lowering the flow rate resulted in many significant beneficial effects on outlet water chemistry: lower outlet manganese concentrations (over the short term), higher outlet pH, lower outlet acidity, higher outlet alkalinity, higher outlet sulfide, lower outlet sulfate, and lower outlet redox potential. Supplementation of the wetlands with dairy whey resulted in lower outlet manganese concentrations (over the short term), marginally higher outlet sulfide levels, and acted to lower the redox potential under the high flow regime. Wetlands receiving a neutral pH had lower outlet acidity, higher outlet alkalinity, lower outlet sulfate, but equivalent outlet manganese concentrations than wetlands receiving an acidic pH. When manganese is the primary mine water contaminant and a passive water treatment system is to be used, it is recommended that crushed limestone with negligible surface water be used in place of composted materials. This recommendation assumes a source water with circumneutral pH and an absence of other metals.

Jan 1, 1993

The Aluminum Company of America announced a temporary reduction of the operating rate at its primary aluminum plant at Palestine, TX where it is developing a new process to produce aluminum metal by electrolysis of aluminum chloride, Output will be reduced by half to about 7,500 tons per year while some improvements are being made on the chemical segment of the plant. The modifications were expected to take 3 to 4 years to complete. Alcan Alumininum Ltd., a major U.S. supplier of aluminum, reported declaration of force majeure on aluminum ingot shipment commitments following the shutdown of its primary aluminum plants at Arvida, Isle Maligne, and Beauharnois, Que. The shutdowns, which began early in June, resulted from management and labor differences.

Jan 1, 1979

By David J. Kusler

This study is an appraisal of the feasibility of recovery and the possible chemical and physical uses of the limestone from the Greenbrier Formation in western West Virginia. Data on minability, occurrence, quality, and markets were obtained from published and unpublished sources and by a limited mail survey combined with personal contacts. The estimated costs of recovery by deep mining techniques are considerably higher than competitive surface and shallow subsurface operations. Compositional in formation available for this study was limited but indicated the suitability of the limestone for most physical uses and some chemical process uses in appraisal of the uses and demand reveals that immediate markets may be difficult to establish, but for some uses long-term prospects may be encouraging, especially if the quality of limestone would be suitable for lime manufacture or use as metallurgical fluxstone.

Jan 1, 1968

By J. Dean Warner

From 1984 through 1987, the Bureau of Mines investigated numerous prospects and new discoveries of columbium, rare-earth elements (REE), uranium, zirconium, and other metals associated with the multi-phased peralkaline granite at Bokan Mountain, southeastern Alaska. This report summarizes the mineral evaluations and estimates indicated and inferred resources for those prospects containing significant tonnage and grade. A total of approximately 96.2 MM lb Cb205 (43 pct of the tonnage at a grade exceeding 0.125 pct Cb205), and 11.8 MM lb U308, 27.9 MM lb Th02, 133.0 MM lb Y203, 637.6 MM lb ZrO2, and 241 MM lb REO are estimated to be contained within nine deposits totalling 37.8 million tons (at least 80 pct of resource tonnage also exceeds 0.5 pct Y203 + REO). Generally, half of the REO content is composed of the heavy yttrium subgroup. Several deposits also contain beryllium and tantalum; 2.1 MM lb of Ta205 and 8.9 MM lbs of BeO were estimated. These estimates would likely be substantially increased with additional exploration. Four deposit types were investigated; shear zones and fracture-related deposits, pegmatites, mineralized dikes, and placers. Mineralized dikes contain most of the beryllium, columbium, tantalum, yttrium, zirconium, and REE resources, whereas shear zones and fracture-related deposits (Ross-Adams mine) contain the principal of the uranium resource. Pegmatites are similarly mineralized as are dike deposits, and contain low levels of gold. Placer potential is suggested, but no deposits were found.

Jan 1, 2011

By Hazel J. Stratton

IN THE HALF-CENTURY that has passed since the Bureau of Mines was established in July 1910, the research and technologic investigations conducted by the Bureau's scientists, engineers, and other personnel have helped significantly in improving health and safety in the mineral industries and have contributed substantially in conserving the Nation's mineral resources through improved techniques in the mining, treatment, and use of mineral commodities. From Bureau laboratories have come new materials for industry and better methods of extracting and processing minerals and mineral fuels. Bureau safety investigations-complemented by equipment testing and by programs of mine inspection and education-have brought about safer and more healthful working conditions.

Jan 1, 1960

By John A. Davis, David W. Brunton

During the past few years great progress has been made in the United States toward safer, more efficient, and more economical tunneling methods. This advance is partly due, no doubt, to the recent increase in the number of tunnels and adits driven for devel- oping and draining mines and transporting ore. The Bureau of Mines during 1911 and 1912 made a special examination of this phase of mining operations, in connection with an investigation of mining methods and means for preventing accidents. The details especially studied were the provisions for the safety of employees, the kinds of equipment, the methods of driving, and the costs of con- struction. The results and conclusions obtained from that investi- gation are discussed and summarized in this bulletin. Up-to-date information concerning tunneling methods is difficult to obtain. There are few books on the subject; and much of the material they contain, although interesting and of value historically, is now obsolete. The engineering periodicals, it is true, endeavor to keep abreast of the times, and several in nearly every issue present some article bearing upon tunnel work. But the very multiplicity of these articles prevents one from reading them all, and the foreman or superintendent in charge of a tunnel, or the mining engineer designing one, and especially the business man financing the project, has no time for a lengthy search after scattered articles in order to determine the present status of tunnel work. Then, too, knowledge of new methods travels slowly. Valuable inventions and improve- ments in tunneling as well as in all the other industries frequently remain in the notebook of the investigator, or as theses are buried in university libraries, or are published only in journals of small scien- tific societies. New tunneling methods and equipment that are prov- ing safe, efficient, and economical may be totally unknown outside the district in which they originate. This paper, based on a special examination both in the field and in engineering literature, is in- tended to supply data concerning modern and recent tunneling practice in the United States, and to make suggestions that, it is hoped, will result in a saving to the mining industry of energy, capital, and life.

Jan 1, 1916

By W. L. Brien, O&apos

Molybdenum alloys with good strength properties at elevated temperatures were produced by the powder metallurgical internal oxidation method previously applied to tungsten and known as oxyreaction strengthening. Commercial molybdenum powders were blended with 0 to 10 pet of a reactive powder, ZrMo2. The effects of composition, blending procedure, and sintering conditions on strength properties at elevated temperatures were studied. Strengthening was attributed to zirconium in solid solution with molybdenum and to the presence of submicrometer particles of Zr02. Several alloys had tensile strength and stress-rupture properties com-parable with those of the best commercial alloys. The maximum tensile strengths obtained were 92 kpsi at 1,200° C and 53 kpsi at 1,316° C. The maximum stress-rupture life at 30 kpsi and 1,200° C was 145 hours.

Jan 1, 1974