Search Documents

By Robert E. Johnson

1962 was the second year of recovery from the mild 1960-61 recession. The year-to-year gain in constant dollar gross national product, our most comprehensive measure of the country's economic performance, was 6.0 percent (from $447.7 billion in 1961 to $474.8 billion in 1962). The unemployment rate declined from 6.7 percent to 5.6 percent. Although it was a good year, there were still unused resources of labor and capital which implied that the economy was operating below its potential. The year-to-year change in the Federal Reserve Board (FRB) index of industrial production of 7.6 percent masked the fact that more than one-third of the growth took place within 196L The monthly index rose only 4.8 percent during 1962, from 114.3 in January to 117.8 in September. The fact that the economy as shown by the industrial index, rose rapidly in the first half of the year only to remain on a plateau of 119-120 during the second half, led some people to fear an imminent downward turn. This did not occur. Neither production nor consumption of mineral fuels advanced as fast as the total economy. But consumption showed more gain than production, 5 percent compared with somewhat less than 4 percent. Production of both crude oil and natural gas reached new highs while bituminous coal production was the highest in 5 years.

Jan 1, 1963

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

By John D. Watson

The results of extensive field tests of a new and powerful method of hard rock excavation are presented in this report.* The method, known by the acronym REAM (Rapid Excavation and Mining), employs high velocity, smooth bore cannons to efficiently deliver energy to the rock and has been demonstrated for underground tunneling, drilling, surface benching, scaling, and secondary breakage in hard granitic rock at the Hope Valley Mine test site in California. Solid projectiles made from inexpensive materials such as concrete or steel, and weighing from 8 to 12 pounds, are launched by conventional high speed cannons and impact the rock at velocities of 5000 feet per second--an impact energy of about 4 million foot pounds (Figure 1). The energy applied at peak pressures of nearly 2 million psi over a period of tens of microseconds breaks down the rock by a complex mechanism of crushing, spalling, and initiation and propagation of fractures produced by the interaction of successive impacts and free surfaces. The main objective of the tests during 1973 was a demonstration of controllability of the underground operation of a silenced cannon. To accomplish this objective a 90-mm cannon

Jan 1, 1974

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. face drill. The instructions are based upon an actual installation made in the mine on face drill model 460-S. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other face drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other face drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By Harold E. Marr

A simple algorithm is presented for processing digitized X-ray spectra obtained with a Si(Li) or Ge(Li) semiconductor detector coupled to a multi- channel analyzer. The simplified least-squares procedure is used to smooth out the statistical fluctuations in the spectrum by repeatedly fitting a quad- ratic equation to a predetermined number of channels and performing a traveling smooth across the spectrum. A logarithmic transform is applied to the raw data to minimize the distortion of the gaussian-shaped peak profiles. The efficacy of the technique is evaluated by observing the distortion of several gaussian-shaped peaks that have been subjected to the smoothing operation. The locations of maximums and minimums in the spectrum are predicted in the process as well as the values of the peak heights. The convolution integers from a least-squares fit of a quadratic equation are calculated as part of a FORTRAN subroutine. The building-block approach to computer programing in a small laboratory is discussed.

Jan 1, 1972

By H. S. Kennedy

THE HELIUM ACT (50 Stat. 885; 50 U. S. C. 161,163-166), as amended, places the responsibility for conserving, producing, and selling helium upon the Secretary of the Interior, acting through the Bureau of Mines-the only producer of helium in quantity in the world. It operates 4 plants-I each at Amarillo and Exell, Tex.; Otis, Kans.; and Navajo (Shiprock), N. Mex. The demand for helium has increased steadily since the decline immediately after World War II and is expected to exceed the capacity of the present plants in the near future. The Congress has appropriated $6,000,000 far constructing a new plant. In addition to providing additional capacity to meet increased demands for helium, the new plant will enable the Bureau of Mines to better conserve the helium in, the Government-owned reserves at Amarillo and Navajo.

Jan 1, 1958

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

By R. A. Franks, G. F. Friel, J. C. Edwards, A. C. Smith

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system's ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system's ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system.

By Paul M. Buttermore

As part of a national canvass of water use the Bureau of Mines compiled data on water requirements in the petroleum and natural gas industries for the calendar year 1962, specifically in well drilling, secondary-recovery operations, and natural gas processing plants. Total new water use in the petroleum industry of the United States, excluding refining, was 5.3 billion barrels. Secondary-recovery operations and natural gas processing plants required about 2.5 billion barrels of new water input; each of these requirements was about eight times greater than that for well drilling. Total use, including recirculated water, was 45.3 billion barrels of which 3.4 billion barrels was consumed. The greatest use of recirculated water was for natural gas processing, amounting to 38.2 billion barrels. Projections of total water use show that by 1975, 75.4 billion barrels will be used by the petroleum industry, of which 10.2 billion barrels will be new water. By 1985, the total use requirement will be 92.8 billion barrels, of which 13.1 billion barrels will be new water.

Jan 1, 1966

By Paul M. Buttermore

As part of a national canvass of water use the Bureau of Mines compiled data on water requirements in the petroleum and natural gas industries for the calendar year 1962, specifically in well drilling, secondary-recovery operations, and natural gas processing plants. Total new water use in the petroleum industry of the United States, excluding refining, was 5.3 billion barrels. Secondary-recovery operations and natural gas processing plants required about 2.5 billion barrels of new water input; each of these requirements was about eight times greater than that for well drilling. Total use, including recirculated water, was 45.3 billion barrels of which 3.4 billion barrels was consumed. The greatest use of recirculated water was for natural gas processing, amounting to 38.2 billion barrels. Projections of total water use show that by 1975, 75.4 billion barrels will be used by the petroleum industry, of which 10.2 billion barrels will be new water. By 1985, the total use requirement will be 92.8 billion barrels, of which 13.1 billion barrels will be new water.

Jan 1, 1966

By W. A. Calhoun

This report gives results of metallurgical investigations performed by the Bureau of Mines on mineral samples taken during April 1959, from Hawaiian bauxite deposits on the islands of Kauai, Maui, and Hawaii. The bauxite samples were tested at the Bureau's Rolla Metallurgy Research Center, Rolla, Mo., to determine if alumina could be extracted. The results were encouraging. Extraction of the alumina by the American Bayer type digest of crude ore samples from Kauai, Maui, and Hawaii recovered 78.8, 73.1, and 70.0 percent, of the total alumina, respectively. These recoveries were increased to 82.8, 85.5, and 79.5 percent by modifying the treatment, which consisted essentially of calcination and weak caustic desilication to provide a residue. The residue was then treated with calcium oxide and digested in a strong caustic solution to extract the alumina.

Jan 1, 1962

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr203. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 1.6 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, scope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider scopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By Nancy Estrada, Jane Nowell, Cathy Jennings, Debra Yniguez, Carol Lavery, Kristin Harrer

Pilots of the MH-60S helicopter are exposed to continuous whole body vibration (WBV). Pilot fatigue is a growing operational concern due to the increased frequency of extended durations of missions (6-8+hours) in support of Operations Iraqi Freedom and Enduring Freedom. Endurance aspects of the currently used rotary wing seating systems were not optimized for the longer missions and wide range of pilot anthropometric measurements, which is now typical of naval aviation. The current seating systems were designed primarily to meet crashworthiness requirements, not for the wide range of pilot anthropometry or to mitigate WBV. Albeit, an issue, pilot fatigue and reduced mission effectiveness are also critical concerns. Current Hazard Reports indicated that pain in pilots’ legs and backs begin two to four hours into the flight and increase with time. Mission readiness also decreases with an increase in flight duration due to the constant distraction of pilots shifting in their seats while trying to get comfortable. Froom, et al [2] reported a dose-response relationship between the length of military helicopter flights and back discomfort. He also concluded that this pain is typically dull, over the lower back, and its prevalence and intensity are dependent on the total flight hours of exposure. Methods This study evaluated WBV produced in the pilot seating systems onboard the MH-60S. The purpose of the study was to test and compare the effectiveness of two different seat cushions, the current seat cushion versus an anti-vibration seat cushion. Both seat cushions were measured for acceleration levels averaged over five-minute intervals using a triaxial seat pad accelerometer. The recordings were completed for a 3-hour straight and level flight. A frequency analysis from 0-80 hertz (Hz) was conducted on all acceleration measurements to determine the dominant axis and frequency of the pilots’ vibration exposure. The results were then compared to the applicable Threshold Limit Values (TLVs) established by the American Conference of Governmental Industrial Hygienists (ACGIH) [1] and the International Organization for Standardization (ISO) 2631.1 [3] to determine the MH-60S pilots’ permissible exposure time for both seat cushions. Results The results of the study showed that for both seat cushions the vibration levels of the z-axis at 16 Hz had the shortest allowable exposure duration, according to the ACGIH TLVs. In the z-axis at 16 Hz, the MH-60S’s current seat cushion’s acceleration levels indicated an exposure time limit of approximately 6 hours, while the anti-vibration seat cushion’s acceleration levels pierced the 8-hour exposure time limit curve. This is shown in the graph below.

Jan 6, 2006

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crushed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling at the same group of quarries. OBJECT Or STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By Leslie S. Rubin

A ventilated helical boost pump was developed that can handle varying flow rates and/or solids concentrations while operating at a single rotational speed and without computer assisted feedback controls. The boost pump developed and briefly tested during this program was designed to accomodate flows suitable for a 3-in. diameter pipeline. The boost pump's ventilated design provides the automatic pressure regulation needed to meet the system's requirements for supporting transient pipeline flow.

Jan 1, 1984

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

By R. L. Gall

This report describes Bureau of Mines experiments in gasifying coal in a helium-heated tube-coil reactor. The purpose of this work was to investigate helium as a medium for transferring heat from a nuclear reactor to gasify coal or for use as high-temperature process heat. A laboratory-scale system was designed and constructed to demonstrate feasibility. In preliminary tests with this system, in which the coal was fed as a water slurry, the helium-heating and recycling equipment operated well. Considerable difficulty was experienced, however, in preheating coal slurry to the desired range of 400° - 1,000° F. without plugging the preheaters. Five different preheaters plugged with coke or with salts leached from the coal. The longest operating period wan 12 hours. These difficulties were partly due to the relatively small equipment and flow rates. The gasifier processed l pound per hour of low-rank coal at 300 p.s.i.g. and 1,800° F., with the carbon conversion limited to 20 to 30 percent by the short residence time and slow heat-transfer rate.

Jan 1, 1962