Search Documents

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987

By William J. Campbell

The purpose of this investigation was to develop a rapid, accurate method of analysis for small amounts of calcium in wolframite concentrates. This analysis is necessary to determine if the wolframite concentrates meet United States National Stockpile Specification P-57R2, which limits the calcium content to 0.2 percent. Because of the small depth of the sample analyzed in fluorescent X-ray spectrography, the calcium Kaline intensity was a function of the chemical composition of the calcium-bearing particle as well as the total matrix composition. This particle-composition effect was particularly important in this analysis, as the calcium may be present as a carbonate, tungstate, phosphate, etc. Three methods of preparing the sample eliminated the variation of calcium Ka intensity with mineralogical occurrence: (1) Reduction in particle size by extensive grinding, (2) chemical fusion with sodium carbonate, and (3) solution of the calcium by an acid attack.

Jan 1, 1958

By Zsuzsanna Zborovszky

Experimental study directed toward gaining improved understanding of the exact mechanisms causing ignition in the PTB breakflash. Investigation and comparison of tungsten and copper wires as to their ability to cause hot wire ignition. Evaluation of the importance of discharge duration in the ignition process. Study of the parameters influencing the duration of a discharge (minimum discharge voltage, purity of electrode materials, purity and properties of the gaseous atmosphere contaminations, deposits on the electrode surface).

Jan 1, 1976

By George N. Aul

This report describes a method developed by the Bureau of Mines for sealing horizontal degasification holes so that they do not create a gas explosion hazard when intercepted by mining. A cement slurry is pumped into the hole through an injection pipe that extends to the back of the hole. Pumping continues until the slurry returns through the annulus to the hole collar. The hole is then shut in and the grout allowed to harden. Application of the procedure to six horizontal degasification holes at Eastern Associated Coal Corp.'s Honey Run shaft is discussed.

Jan 1, 1979

By P. D. Kovscek

High-pressure streams of water, known as water jets, can be used to improve the cutting efficiency of mechanical bits. During prior testing by the Bureau of Mines, the cutting performance of a longwall shearer, equipped for water-jet-assisted cutting, was evaluated. The performance of the shearer did not improve while using water jet assist because the pressure of the water delivered to the rock surface was inadequate. The study, described in this report, resulted in a determination of the major cause of water pressure loss on the shearer, and an evaluation of the techniques for increasing the water pressure at the rock surface. The results show that the major pressure loss, which occurred between the nozzle and rock surface, is directly affected by the amount of fluid turbulence that develops just upstream from the nozzle. Preventing a sudden change in the direction of the flow channel can increase the stagnation pressure as much as 400 pct. Smoothing the surface of the flow channel in the shearer bit block would increase the stagnation pressure delivered to the rock surface by 35 pet.

Jan 1, 1989

By Alan R. Buehler

A mineral survey of the 67, 110-acre Raven?s Eye WSA (Wilderness Study Area) in the north-central Snake River Plain of Idaho was conducted by the U.S. Bureau of Mines in 1985, at the request of the Bureau of Land Management. The WSA is in Blaine and Lincoln Counties; the northwest corner is about 1 mile east of Carey, 10. A search of county mining claim records indicated that no claims have been located in the WSA. Basaltic lava is the only rock type exposed within the WSA. A platy variety of lava (slab pahoehoe) occurs that is produced from other lava fields in southern Idaho. The material is marketed as decorative stone, used for wall veneers, and retails for approximately $125/ton. Within the W5A, approximately 18,000 tons of indicated reserves are concentrated in two areas, and a total of 12,000 tons of indicated subeconomic resources were found at six other localities. An additional 10,000 tons of inferred subeconomic resources are unevenly distributed over the remainder of the WSA.

Jan 1, 1986

By R. R. Wells

This report summarizes the results of laboratory investigations by the Alaska Mining Experiment Station, Juneau, to determine the practicability of treating cinnabar-stibnite ore by bulk flotation and controlled-atmosphere roasting of the concentrate. Ore from the Red Devil mine near Sleetmute, Alaska, was selected for testing; it is typical of ores widely distributed throughout the Kuskokwim River Basin. The material, consisting of stibnite and cinnabar in ankerite, dolomite, and quartz, assayed 1.55 percent Hg and 2.87 percent Sb. Continuous treatment of the ore in a laboratory flotation circuit recovered 95.7 percent of the mercury and 82.6 percent of the antimony in a concentrate that assayed 20.4 percent Hg and 34.6 percent Sb.

Jan 1, 1958

By Martin Hertzberg

The early and reliable detection of the self-heating of combustible substances in mines is of considerable importance to the mining community. This Bureau of Mines report describes the results of a variety of studies of incipient combustion and its detection. Heated samples of coal, wood, and various polymers were used to evaluate the relative sensitivities of several types of detectors. The laboratory results indicate that submicrometer particulate detection is the most universal and sensitive method. Carbon monoxide detection was as sensitive as submicrometer particulate detection for pyrolyzing coal but was relatively insensitive to pyrolyzing wood or plastics. The conventional type of ionization smoke detector was the least sensitive for coal and of intermediate sensitivity for wood and plastics. Self-heating experiments with Pittsburgh seam coal piles of varying particle sizes gave ignition temperatures of 170° C for 4-to 7-µm dust, which increased monotonically with particle size. The measured heating rates were compared with data from an adiabatic calorimeter to obtain preexponential rate constants. The preexponential rate constants varied linearly with the surface area per unit mass of sample as would be expected for heterogeneous surface oxidation. The propagation behavior of ignition waves and the overall self-heating appears to depend critically on the magnitude of the convective flows induced, which counteract the depletion of oxygen in the void spaces of the pile. Classical theories of thermal ignition require substantial modification to be applied reliably to such cases.

Jan 1, 1977

By Paul Hatmaker

A primary, function of the Bureau of Mines is to encourage elimination of waste and the most profitable use of mineral raw materials. In line with this objective the Bureau has frequently stressed the importance of waste utilization at stone quarries. From time to tine studies both technical and economic in character have been made of problems pertaining to the most efficient use of natural, stone, particularly that which may be classed as a by-product of the higher grades of dimension stone. Every quarry producing ornamental or building stone yields large quantities of material that for one reason or another is unsuited for high-grade products, even though a great deal of work has been expended upon it more or less unavoidably. It is obviously good judgment to sell this odd-sized or off-grade stone at whatever price can be obtained rather than to spend more money to place it on the waste dump. In many cases, however, a really profitable side line has been developed.

Jan 1, 1933

By Michael G. Zabetakis, Israel Liebman, Henry E. Perlee

Flammability studies conducted to date on stratified methane - air and pentane - air mixtures in air indicate that location and extent of a flammable layer are affected by molecular diffusion , gas motion , and propagation of flame . In initially quiescent mixtures , the lower limit - of - flammability zone may be determined by assuming molecular diffusion alone governs mixing rate . The upper limit - of - flammability zone can be predicted in this manner only for stratified layers with small concentration gradients ( less than 0.2 volumepercent per inch ) ; where large concentration gradients are encountered ( for example , as much as 30 volume - percent per inch ) , the initial - mixture methane concentrations that yield flammable mixtures are larger than anticipated . Flames propagating through heterogeneous quiescent methane - air atmospheres in the direction of the concentration gradient exhibit flame speeds at any point that corresponds to the flame speed of the homogeneous gas mixture having the same gas composition as that of the point in the heterogeneous system . In flowing mixtures with large concentration gradients , the degree of mixing prior to ignition does not appear to affect the flame velocity and emitted radiation appreciably in a 6.5 - ft - diameter gallery .

Jan 1, 1964

By J. K. Whyatt

Assuring ground control safety in many mining and tunneling projects depends, at least in part, on an understanding of in situ stress conditions that will be encountered. Yet it is rarely practical to conduct more than a very limited number of stress measurements. Stresses along the route of a proposed excavation are typically interpolated from available measurements, often assuming a linear variation of stress with depth (or elevation). However, projects where multiple stress measurements are conducted often report more complex variations of in situ stress, usually in apparent relationship to geologic structures. These structures often include lithologies of contrasting elastic properties. A method is proposed for estimating stresses in these cases by first back-calculating regional loads from available stress measurements and then modeling the distribution of stress throughout the rock mass. The method has been successfully applied to a set of in situ stress measurements from the Coeur d’Alene Mining District of northern Idaho, USA. Results provided new insights into district stress conditions and the distribution of rockburst hazards along mine drifts and between various mines. This success should transfer readily to suitable deep tunneling projects.

By Douglas A. Elkins

The unique characteristics of plasmas, their current applications, and ongoing research into new applications are described. Major technical and economic problems in application of plasma technology are discussed. Examples of potential applications of plasma in extractive metallurgy are described and evaluated. The report includes a selected bibliography of articles on plasma and related high-temperature technology.

Jan 1, 1969

By J. E. Matta

The methane gas emitted from coal samples collected from the conveyor belts dumping into silos was measured by the Bureau of Mines. Approximately 50 pct of the total gas desorbed into a sealed can within 1 week was released during the first 24 hours. No simple correlation between the gassiness of the coal stored and the methane concentration in the silo open space above the coal was found. This was probably because the gassier coals were stored in open-top Silos, which were better ventilated. Although the methane concentration in the open space above the coal pile was less than 1 pct for all 34 silos investigated, a methane measurement in the coal pile showed that high methane concentrations can exist. The methane released in the pile appears to accumulate and not liberate freely into the open space above the coal pile. Probably this gas is released during reclaiming operations, but further research is required to substantiate this claim.

Jan 1, 1978

By Frank W. Sansom

This paper is one of a series of articles dealing with milling methods and costs at metal mines in the United States, written in accordance with an outline prepared by engineers of the United States Bureau of Mines and published by the bureau. The Netta mine and concentrator is the largest of the plants of the Eagle-Picher Lead Co, It is located in Ottawa County, in the extreme northeast corner of Oklahoma, and in what is known as the Tri-State zinc and lead mining district, embracing the northeast corner of Oklahoma, the southwest corner of Missouri, and the southeast corner of Kansas. A majority of the production comes from the Oklahoma section, with Kansas second, and Missouri third.

Jan 1, 1930

By R. C. Diehl

Coal, fly ash, and flue gas samples were analyzed for mercury (Hg) by double gold amalgamation-flameless atomic absorption spectrophotometry. The purpose of the study was to elucidate the fate of the trace mercury in the coal when the coal is burned. Samples were collected from a bench-scale 100-g/hr combustor, a 500-lb/hr combustor, and three coal-burning powerplants. In all cases mercury was found in the fly ash. The amounts ranged from about 9 to about 70 percent of the mercury in the coal that was burned.

Jan 1, 1972

By R. R. Sayers, W. J. McConnell

"The health, comfort, and efficiency of men engaged in the mining industry may be impaired, in some instances very seriously, by abnormal physical conditions of the mine air or by variations in its composition. This is true in some of sheet metal mines of the West where high temperatures with varying humidities are encountered. Physiological studies have been made in some of these mines showing the effects of various temperatures end humidities. As it is difficult to carry out studies on many controlled temperatures, it was thought best to make the experiments in a laboratory and apply the results to the industry insofar as practicableThe effects of moderately high temperatures and humidities are more difficult to measure perhaps than the extreme conditions, but may be predisposing causes of fatigue, discomfort and disease, A cooperative study of the physioloical effects of heat and humidity is being conducted by the Bureau of Mines and the U. S. Public Health Service cooperative with the American Society of Heating and Ventilating Engineers, in the Research Laboratory of the Bureau of Mines at Pittsburgh, Pa."

Mar 1, 1924

By Charles Vaught, Richard S. Fowkes, Ronald S. Conti, Barbara Fotta, William J. Wiehagen

The purpose of this study was to determine mine workers' state of fire-fighting preparedness and the technology being used to detect and respond to underground coal mine fires. To investigate this problem, 214 underground coal miners were interviewed by U.S. Bureau of Mines researchers. Frequency distributions of workers ' responses are presented in this report, along with segments of narrative accounts, to profile miners' fire-fighting capabilities. The data indicated that much variability exists from mine to mine and that there are several important changes operators may undertake in order to make miners better prepared to deal with fire underground: select appropriate sensors, establish and test a warning and communication protocol, construct a system capable of delivering hundreds of gallons of water per minute for sustained periods, institute formal fire preparedness audits, develop case studies of events that occur at an operation to use as teaching and assessment tools, and provide structured practice that can be incorporated into fire drills.

Jan 1, 1995

By Carlton E. Brown

[The purpose of this report is to present results of tests on the effectiveness of a spray of water mist, commonly called compressed-air water blast or water blast, in reducing the concentration of dust present in the air shortly after blasting and during mucking of the blasted material. Many observations have been male on the effectiveness of such ,sprays, but published quantitative information on comparative dust concentrations with and without their use, obtained by dust-sampling methods in use in this country, is rare if not absent. Tests conducted. in South Africa about 19164/ and more recently in England5/,6/ have shown that such sprays reduce the dust concentration to very low values within a fen minutes after blasting.]

Jan 1, 1938

By Larry A. Haas

A major problem encountered in dump leaching operations is the plugging of both the dump and the piping by precipitated iron compounds. Bureau of Mines research to obtain basic data on agitation leaching and dump leaching methods has shown that the addition of organic chelating reagents can significantly enhance the lixiviant permeability through the ore and the concentration of the metal values in the liquor. For example, the addition of 5 giL citric acid (CA) to a conventional sulfuric acid lixiviant almost doubled the fluid flow rate through 5-cm-diameter laboratory columns containing copper ore. After 185 h of per-colation leaching, the metal concentrations with (and without, in parentheses) CA were 1.7 (1.5) giL Cu, 200 (70) ppm Mn, 160 (40) ppm AI, and 6 (3) ppm Co. The enhancement of metal concentrations with chelating reagents such as CA was confirmed by determining the solubil-ity of several metal ions as functions of pH and chelating reagent con-centration. When ferric ions became insoluble at pH values above 3, the concentrations of other ions also decreased. The addition of che-lating reagents kept iron, as well as the other dissolved metals, in solution even at pH values as high as 5. Citric acid was a more effective chelating reagent than gluconic acid, oxalic acid, or sodium lignin sulfonate.

Jan 1, 1985

By Ronald H. Church

As part of the Bureau of Mines health and safety research program in strata control, a ground-penetrating radar (GPR) system capable of pene-trating approximately 10 ft into the mine roof has been devised to identify anomalistic conditions. The GPR system consists of a transmitter with carrier frequencies of 250, 500, and 1,000 MHz, utilizing a dipole antenna, and a receiver, consisting of a dipole antenna fed into a sampler with a time base housed in a storage oscilloscope. A computer was utilized for data acquisition and data processing. Data analysis by computer enhancement revealed recognizable return ra-dar signatures from the middle man rock and main roof of the test site. These stratigraphic anomalies can be cataloged for recognizable fea-tures, which from the past history of the mine may have been shown to create strata control problems. Early recognition of such features could lead to immediate corrective actions and result in the saving of lives.

Jan 1, 1985