Search Documents

By A. E. J. Gallagher

This report summarizes the results of flotation studies conducted by the Federal Bureau of Mines on samples of extremely fine-grained lead-zinc sulfide ores. Samples from five ore deposits in the Pine Creek area, Coeur d'Alene district, Idaho, and one deposit in the Metaline district, Washington, were studied at the Albany Metallurgy Research Center to determine the recovery of sulfide lead and zinc by flotation. During the investigation it was found that flotation could be effectively applied to the selective recovery of exceedingly fine-grained lead and zinc sulfide minerals. Separation of galena and sphalerite was obtained on pulps ground through 1,600-mesh, in which most of the particles were smaller than 5 microns. Selectivity and recovery of minerals in this fine size range were enhanced by use of a chemical dye, diphenylthiocarbazone, as a galena promoter. Although unsuccessful on one ore, application of the dye in treatment of two other very fine-grained ores yielded lead concentrates containing over 62 percent Pb at recoveries in excess of 85 percent. More than 55 percent of the lead in these concentrates occurred as particles smaller than 2 microns.

Jan 1, 1961

By Jack R. Woodyard

Scientists at the U.S. Bureau of Mines are studying iron aluminides as possible substitutes for stainless steels to reduce the Nation's dependence on imported strategic and critical materials. In a Bureau investigation on the mechanical properties of Fe-28Al, it was found that the material's machining properties were significantly improved at slow tool and feed speeds. Machining techniques normally used for brittle materials failed or were costly. Further experiments using a 5-in (12.7-cm) mill cutter with carbide inserts, operating dry at minimum machining speeds, produced visually smooth sample surfaces with no tool damage. As a result of these experiments and a review of published data on hydrogen embrittlement of iron aluminide under tension, non-water-based (e.g., sulfur-based) lubricants were chosen for production machining. Four-flute, 3/4-in (19-mm) carbide end mills were used at slow speed under lubrication. This latter procedure reduced tool wear and breakage by a factor of 2. Machined surfaces and specimen cross sections were analyzed by scanning electron microscopy to detect microcracking. Tensile tests gave the expected yield and ultimate strengths, indicating that no degradation by low-speed machining occurred. This study extends this work to show that the alloy can be machined at higher speeds using high-speed steel end mills, and that water-soluble cutting oil is a suitable lubricant and coolant.

Jan 1, 2010

By E. A. Barrett

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent-image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3-D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 2010

By Raja V. Rarnani, Robert L. Frantz

"The more than 75 research projects funded throughout the first 10 years of the Dust Center's operation have resulted in numerous cumulative findings fulfilling the goals of the Center. These project descriptions present the methodologies and project-to-project relationships leading to their various accomplishments and demonstrate the mesh between project objectives and Center goals.To develop equipment for collecting respirable dust samples.To develop experimental methods for particle-by-particle characterization of morphology, size, and chemistry.To develop experimental methods for overall respirable dust sample characterization of size distribution, chemistry, and crystallography.The project directly addresses the Center's goals to enhance the understanding of the scientific and engineering characteristics of fine and respirable mineral particles found in mining and milling atmospheres and to establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment, and control measures) in the generation of fine particles. The project also aims to contribute to the development of control mechanisms for reducing ambient respirable dust concentrations and worker exposures.The work on this project is related to similar work on Coal Mine Dust Characterization (Project No. 2701/MN1) and Characterization of Dust Particles (Project No. 4203/PS3).Airborne dust sampling was performed at the following locations: 1) a sand and gravel quarry in Southern New Hampshire, 2) a welding facility, 3) a ceramic powder facility, 4) a metal powder facility, and 5) the air in Cambridge, Massachusetts. A portable sampling box incorporating two Sierra personal cascade impactors was designed and produced. At a 2-LPM flow rate, the effective cut-off diameters of the Sierra impactors were 10.0, 6.0, 3.5, 2.0, 0.9, and 0.5 mm, respectively, for each stage, and the air passed through a PVC filter after the last stage. In addition, the sampling box contained a total respirable dust filter. The substrates were weighed carefully before and after collection, and the weight increases were recorded. All films, foils, and filters were put in the balance chamber for more than 8 hours to stabilize the temperature and humidity before weighing. A Cash 21 microbalance (±0.001 mg) was used to weigh the Mylar films, SS films, and filters."

Jan 1, 1995

By Gwendolyn D. Hood

The Bureau of Mines investigated techniques for dewatering slurries from talc-processing operations to improve water reclamation and pro-duce dewatered solids suitable for disposal. Various flocculating reagents were evaluated, and a nonionic polyacrylamide was found to be most effective in a specialized flocculation dewatering technique. The flocculation dewatering method was applied in laboratory batch tests and in continuous tests using a static screen, a belt-roller device, and a clarifier-thickener laboratory unit. In continuous tests using the unit, wastes of 3.5 pct solids were dewatered to 56.9 pct solids using 0.03 Ib of flocculant per ton of dry solids treated.

Jan 1, 1983

By F. N. Kissell, R. J. Bielicki, J. H. Perkins

A sorption apparatus for measuring the equilibrium sorption isotherm and the rate of diffusion of methane from fine-sized coal was designed and constructed. Preliminary work that used Pittsburgh and Pocahontas No. 3 coal shows that the diffusion coefficient varies with pressure and that the fracture spacing in these two coals is substantially different.

Jan 1, 1972

By Kenneth H. Johnston

For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meetings of the Kansas-Oklahoma Waterflood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1960 spring tour of four waterflooding projects in Greenwood County, Kans. (fig. 1). Three of the projects produce oil from the Bartlesville sand, and one produces from the Cattleman sand. The Bartlesville-sand floods have been in operation from 4 to 12 years and have produced about 3,910,000 barrels of waterflood oil from the injection of approximately 64,715,000 barrels of water, a cumulative water-injected to oil-produced ratio of 17 to 1. The Cattleman- sand flood, which has been operating for 3-1/2 years, has produced about 842,000 barrels of waterflood oil from the injection of approximately 9,305,000 barrels of water, a cumulative water-injected to oil-produced ratio of 11 to 1.

Jan 1, 1960

By P. A. Richardson

The current Bureau of Mines active list of permissible explosives includes 76 brands. Eleven are gelatinous and the rest are the granular type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1970

By M. J. Ferrante

Enthalpy and entropy increments above 298.15° K were determined for cop-per sulfate between 298° and 1,000° K and for copper oxysulfate between 2980 and 1,146° K by the method of copper-block drop calorimetry. Enthalpies, entropies, and heat capacities are tabulated for both compounds. In addition, free-energy functions are tabulated for the sulfate. Equations representing the enthalpies are given for each compound.

Jan 1, 1972

By G. H. Cobb, J. L. Johnson, H. H. Heady

An infrared absorbance technique is described for analyzing anodic gases produced during the electrowinning of uranium , thorium , and rare - earth metals in molten fluorides . Typical components determined qualitatively in a gas sample are CO , CO₂ , CF4 , C₂ Fe , C3F8 , COS , CS₂ , and SiF4 . About 20 minutes are required to record and interpret the spectrogram , and report quantitative results for CO, CO₂ , CF4 , and SiF . The procedure is used for control during electrolysis .

Jan 1, 1964

By W. P. Huleatt, R. B. McCulloch

"The Big Four zinc-deposit, directly above the north bank of the Green Mountain Reservoir on the Blue River, Summit County, Cole., was discovered in 1937 by the present owner, Walter McDaniel, who lives on the property. Mr. McDaniel, together with members of his family, have worked the mine on a small scale since its beginning and have shipped quantities of sorted high-grade ore to the International Smelting Co. at Tooele, Utah, and the Combined Metals Corp. at Bauer, Utah. More recently, parts of the nine have been operated by lessees.The property had been examined previously by the Federal Geological Survey, and the geological report was made available' to the Bureau of Mines.The Big Four mining claim was located in 1937 by Walter McDaniel and his wife Frances,- who had been prospecting in the vicinity since 1933. The discovery of the high-grade zinc deposit caused considerable excitement, as it had not been regarded as a mineralized area.Mining was begun in 1937 and carried on until 1944 by Mr. and Mrs. McDaniel with the help of a few hired miners. During 1944, parts of the mine were leased: to various parties Who produced small quantities of ore but did no development work.Shipments during 1941 .totaled 752 tons; during 1942, 387 tons; and during 1943, 510 tons. From the beginning of 1944 to April of that year, 98 tons wore produced and shipped to Utah,Since the lessees began operations, a grade of 30 to 35 percent zinc has been maintained by careful sorting. No production has been recorded for 1945.The Big Four mine is situated on Colorado State- Highway 9 between Dillon and Kremmling on the south face of Green Mountain overlooking the Green Mountain Reservoir, a Federal irrigation project on the Hue River, Green Mountain rises 1,600 feet above the general level of the valley to an altitude of 9,408 feet and the surrounding terrain, i s correspondingly mountainous and rugged."

Apr 1, 1946

By Wallace W. Roepke

Research to evaluate the lubricity effects achieved by spraying water on the cutting bit of a mining machine or spraying water on the coal during cutting has shown that neither practice affects cutting forces, as had been believed. However, when water was supplied to the cutting zone axially through the bit at 3,000 to 5,000 psi pressure, tangent'ial cutting forces were reduced an average of 30 pct at a I-in depth of cut while normal bit forces were reduced an average of 65 pct. Lower normal forces mean reduced bit wear, faster advance with greater depth of cut, and fewer coal fines.

Jan 1, 1985

By Charles S. Allbright

This report describes hydrogenation of petroleum distillate fuels in bench scale equipment and the effects of hydrogenation on the storage stability and the composition of the fuels. Two distillate fuels were hydrogenated in laboratory equipment using a commercially available cobalt molybdate catalyst. Reactor temperatures were varied from 600° to 850° F and pressures from 100 to 600 psig. Product fuels were analyzed by ASTM, Bureau of Mines, mass, and infrared methods. Hydrogenation of a catalytically cracked fuel from Oklahoma crude oil significantly improved the storage stability, reducing insoluble gum formed during 9 months of storage at 110° F from 19.0 to 1.3 mg per 100 ml fuel, average. Conversion of the olefins to other hydrocarbon types varied with the temperature of hydrogenation--at 700° to 850° F the conversion was mainly to aromatics, at 650° F about 50:50 to saturates and aromatics, at 600° F principally to saturates. Processing a fuel composed of a mixture of virgin distillate and catalytically cracked stock, both from Illinois crude, at 700° F and 200 psig effected marked improvement in stability; the buildup of insoluble gum in storage was lowered from 18.3 to less than 1 mg per 100 ml fuel.

Jan 1, 1967

By John C. Gagliardi

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to ISO 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 2010

By H. B. Brunot

The United States Bureau of Mines under provisions of Schedule 2C4 issues approvals covering complete operating units such as loading machines, room hoists, and storage-battery locomotives. Certain manufacturers design and build entire machines. Other manufacturers purchase a part or all of the electrical accessories from manufacturers of electrical equipment and make up permissible units by assembling them. Before the assembler purchases electrical accessories for use in such contemplated units he may require certain information from the accessory manufacturer as to whether the particular accessories are suitable for assembly in his proposed permissible outfit. To aid accessory manufacturers in marketing their product, a provision was incorporated in Schedule 20 whereby tests might be made on individual accessories and reports rendered as to the suitability of a given accessory for use in permissible assemblies.

Jan 1, 1935

By Terry J. Close

The Anaconda Pintlar Wilderness has a significant mineral resource potential. Five deposits have resources totaling about 180,300 tons (163,600 t) containing silver, copper, lead, gold, and zinc. Another 11, not sufficiently exposed to allow resource estimates, may have additional mineral potential. No placer deposits are indicated. There is little potential for the production of sand, gravel, or stone; alternate sources are closer to markets. No oil, gas, uranium, or geothermal energy sources are known to be present.

Jan 1, 1982

By T. M. Barczak

One of the primary goals of Bureau of Mines research is to reduce the cost of coal mining by improving the efficiency of longwall supports. One method of achieving this goal is the optimization of stress distribution within the support structure, resulting in a lower overall weight, more fully stressed shield. However, before stress optimization can be initiated, load conditions must be defined that cause maximum stress in the various support components. A finite-element model of a longwall shield was used to identify these critical load conditions. These load conditions were then evaluated in the Bureau's mine roof simulator (MRS) by instrumentation of a longwall shield and measurement of strains in each of the shield components. The critical (canopy-base contact) load conditions were identified that can cause structural failure at less than rated shield (hydraulic yield) capacity. Comparisons were made between full-contact and partial-contact load conditions. Other parameters investigated included the stiffness of the contact material, changes in shield geometry, rate of load application, and effects of horizontal constraint. Conclusions were drawn regarding the structural integrity of the major shield components and potential for stress optimization.

Jan 1, 1987

By J. W. Town

Recrystallization studies on chrome-bearing spinel materials were made by the Bureau of Mines to determine the effects of certain fluxing agents and cooling rates on the chromium-to-iron ratio of recrystallized spinel. Statistically designed and evaluated tests showed that the ratio of chromium to iron in naturally occurring chrome spinel could be increased from 1.5 to 1 to over 7 to 1 and that the ratio of chromium to iron in the chrome-spinel in a stain-less steel slag could be raised to over 18 to 1. Silica, magnesia, and lime had significant positive effects, while alumina had a significant negative effect. Cooling rates of 200 C per hour in a programmed spiral globar electric furnace were satisfactory for growing crystals of recoverable size.

Jan 1, 1967

By Dipak C. Talapatra

This report describes the development of guidelines for design, inspection and maintenance of automatic couplers. In order to devise the guidelines, performance requirements for automatic couplers were carefully established. This was done through a comprehensive survey of coupler manufacturers and extensive observation of automatic couplers in service in a broad spectrum of mines. The capability of the couplers to withstand the demands of the mining environment in terms of strength characteristics, gathering range, curve negotiability, and other factors were all carefully evaluated. An analysis of coupler related accidents for the years 1972-1976 was carried out to provide information on the safety and reliability of existing automatic couplers. This formed an important input to the development of the guidelines. It is expected that these guidelines will be useful to coupler manufacturers for establishing designs for improved automatic couplers, and to mine operators for maintaining their couplers in a safe and good operating condition throughout their expected lifetime. This report is in two volumes: Volume 1 Technical Report Volume 2 Design, Inspection, and Maintenance Manual

Jan 1, 1977

By John E. Hamak

The identified helium resources of the United States were estimated by the U.S. Bureau of Mines at 617 Bcf, as of December 31, 1992. This includes 285 Bef of demonstrated reserves, 85 Bcf of demonstrated marginal reserves, and 37 Bcf of demonstrated sub-economic resources. The identified resources also include 166 Bcf of helium in inferred reserves and inferred marginal reserves and 44 Bcf in inferred sub-economic resources. The identified helium resources contained on Federal lands are approximately 172 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. Undiscovered helium resources in the United States are estimated at a most likely volume of 104 Bef, with a maximum volume of 249 Bcf and a minimum volume of 41 Bef. Also reported are 51 Bcf of helium in nonconventional and low-helium-content natural gases. Extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1992 was 3.3 Bcf. Some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1995