Search Documents

By A. J. Forney

This report summarizes the findings of methods of treating caking coals in a fluid bed to destroy their caking properties. In batch tests it was found that several coals, including those with a free-swelling index greater than 8, could be decaed at temperatures from 400° to 425° C with a fluidizing gas composed of inert gas or steam containing 0.2 percent oxygen and a minimum residence LS,-;,' of 5 minutes. When treatment decreased the free-swelling index from about 8 to 1-1/2 or lower, the resulting treated coal was noncaking. In a continuous unit with continuous feed and discharge of coal, slightly more severe conditions were required to decake the coal. For 18- to 100-mesh coal a temperature of 430° to 440° C and an oxygen-to coal ratio of 0.4 cubic foot of oxygen per pound of coal feed was necessary. Finer mesh sizes required lower oxygen-to-coal ratios. In tests using air only as the fluidizing medium and treatment temperatures well below the softening range, the caking properties of 150- to 200-mesh coal were destroyed in 30 to 40 minutes of residence time at 200° C. Coarser sizes of 18 to 48, 48 to 100, and 100 to 150 mesh required longer residence time.

Jan 1, 1966

By C. A. Herbert

Information Circular 6746 reviewed the fatalities in Indiana coal mines. for the fiscal year October 1, 1951 to September 30, 1933. Since then Indiana has changed its fiscal year to the period July 1 to June 30, but as most statistical data on accidents are arranged according to calendar years, the data in this paper are for the last 3 months of 1932 and the calendar year 1933, rather than for the new Indiana fiscal year. Tables 1 and 2 list the fatalities in Indiana coal mines3/ by cause and occupation for the last 3 months of 1932 and for the calendar year 1933. The fatalities for the small wagon mines employing fewer than 10 men are separated from those employing 10 or more men to call attention to the ex- tremely high fatality rate in small mines, largely because the State mining law does not apply to them nor do they come under the jurisdiction of the Indiana mine inspectors; as a result health and safety conditions are ex- tremely bad. During the last 3 months of 1932, 5 (approximately 42 percent of the total) fatalities occurred in the small mines, while for the calendar year 1933, 12 (approximately 32 percent) of the fatalities occurred in them. The Indiana Division of Mines and Kining estimates that these small mines have an annual production of approximately 325,000 tons, or about 4.5 percent of the total coal-mine production of the State. In other words, for these small mines the fatality rate per tons mined during 1933 was about 10 times as great as for the mines employing 10 or more men. Another lamentable feature in connection with the fatalities in small mines is that very few carry any compensation insurance and the owners are not worth enough financially for dependents of victims to collect anything under the common law; as a result, the dependents of those killed usually are left penniless and subjects of public charity.

Feb 1, 1935

By J. A. CoRGAN, J. A. DECARLO

The coal -carbonizing industry is recognized as one of our country's most essential industries , and this position has been achieved through its primary function as a source of supply of special fuels and chemical raw materials . When coal is carbonized at high temperatures in slot - type coke ovens in the absence of air , it decomposes into two main products cokę ... and crude gas . Of these , the more important is coke , a hard, strong, porous solid that remains in the oven after the volatile matter in the coal has been driven out by heat . The hot crude gas carries with it all. of the coke -plant products except coke and has a complex composition in the vapor: state . Its processing , to produce the four principal coproducts of coke (tar , ammonia , light oil, and gas ) , is accomplished by preferential condensation and absorption . Although the principal coproducts of coke tar , ammonia , and crude light oil - - gas, are of secondary importance , their

Jun 1, 1949

By Richard L. Unger

The Bureau of Mines entered into a cooperative agreement with an eastern Kentucky coal mining company to comprehensively redesign the flow of equipment and supplies throughout its underground mines. Items were tracked from delivery to the warehouse and from surface storage areas to their final usage locations underground. Three underground mines were visited, and a great variety of tasks were videotaped for subsequent laboratory analysis. Of particular interest were tasks that required manual handling of the supplies or equipment components. Activities such as handling daily supplies (concrete blocks, rock dust, and cross- beams) and handling or lifting the continuous miner power cable were determined to be the most hazardous. Recommendations to the company included redesigned surface storage areas to facilitate the use of forklift vehicles to load the underground supply cars. Designs were also developed for different mechanical- assist devices to help in unloading the supply cars underground and to handle equipment maintenance tasks underground. Additionally, the videotapes of the underground manual handling tasks became the basis for simulating those activities in controlled laboratory conditions. This testing will contribute to developing guidelines for proper lifting techniques for low-seam coal mines.

Jan 1, 1986

By K. H. Johnston

This guide was written to furnish the coal industry with a description of techniques, instruments, and clues on how to find abandoned oil and gas wells that have penetrated coal seams. The report includes specific information on searching techniques currently in use by several coal mining companies, gas-transmission companies, and waterflood operators, as well as information on State agencies responsible for the enforcement of laws and the preservation and distribution of data pertaining to the drilling, development, and abandonment of oil and gas wells. Comparative tests were performed with several commercial electronic metal detectors to determine the feasibility of using them to aid in the search for abandoned wells and to determine the instrument most suited for that particular use. The role of methane detectors to locate abandoned wells is described, including a case history. Tests were made to develop an efficient procedure to follow in systematically searching an area for metallic clues or hydrocarbon evidence to abandoned wells. The guide describes, in detail, a search sequence, including the collection of basic data, preparation of the selected area, and the physical search. Methods are given for evaluating the results.

Jan 1, 1973

By Richard S. Olsen

Prior work by the Bureau of Mines demonstrated a feed preparation method that eliminates the formation of slime during leaching of calcined kaolinitic clay and makes leached residues fast settling and easy to filter. Nitric acid leaching rates determined for calcined kaolinitic clay prepared by this method were found to correspond to a zero-order reaction model for both batch and continuous, stirred-tank leach-ing. A rate constant of 0.136 min-1 was determined. Separation of solid residues from the reacted slurry was examined, and filtration rates were determined. Permeabilities of the flocculated, leached residues were around 51 darcys, or 5.0 x 10-7 cm2 for laminar flow through 4-ft-deep beds.

Jan 1, 1983

By W. L. Crentz

The Black Mesa coal field is part of the Hopi and Navajo Indian Reservation in Apache, Navajo, and Coconino Counties, Ariz. The field is in an isolated area with the nearest railroad 70 to 90 miles to the south. Travel is restricted by roads that become impassable during inclement weather. The area is a mesa and rises from 500 to 2,000 feet above the surrounding territory. Water is very scarce, and the nearest stream of any consequence is the Colorado River about 90 miles northwest from the center of the field. Coal beds are found in the Mesaverde formation of the Cretaceous age, but they are uncorrelated and range from subbituminous to bituminous in rank. Huddle2/ estimates the reserves of subbituminous coal in Arizona at about 15 billion tons, most of which is in the Black Mesa field. The geology of the field has been reported by Campbell and Gregory.3/ Coal production is small, and the output is used almost exclusively for domestic fuel in the Indian schools, missions, and trading posts.

Jan 1, 1955

By B. D. Nash

The object of this research was to investigate the technical feasibility of preparing chromium metal by the thermal decomposition of bisbenzene chromium. Bisbenzene chromium, a pi-bonded sandwich type organometallic compound, was thermally decomposed under reduced pressure to form a metal plate on a heated substrate. Metal recovery was close to 100 percent of theoretical, with deposition rates up to 20.8 mg/hr/cm2. Metal purity was dependent not only upon the purity of the starting material, but also upon the sublimation rate of bisbenzene chromium. Total detectable metallic impurities ranged from a low of 18 ppm to several hundred ppm. In general, metallic impurities were less than 100 ppm. Carbon, the major nonmetallic impurity, ranged from less than 0.3 percent to more than 10 percent. The carbon contamination is most likely a result of the decomposition of the organic portion of bisbenzene chromium. An unusual property of some of the deposits was their outstanding corrosion resistance. Unlike pure electrolytic chromium, which dissolves readily, these deposits were insoluble in hot mineral acids.

Jan 1, 1968

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By Robert W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slurry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton ample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol-ids) 0 The resultant friction-'pressure gradients ranged from 0,06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant.. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposition tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, additional water was releas2d; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitability for use as backfill material in active mines.

Jan 1, 1983

By Thomas J. Blalock

The volumetric determination of uranium according to the method of Sill and Peterson (6),3/ which uses cerate oxidimetry after the separation of interferences such as sulfides and cupferrates, has been used for some time by the Bureau of Mines and gives satisfactory results for many of the samples tested. However, in those instances where the uranium content did not exceed a few tenths of 1 percent and iron was present in the range of 10 to 40 percent (as Fe203),4/ the method was cumbersome and unreliable. The need for a more accurate procedure for the determination of small amounts of uranium in the presence of large amounts of iron, such as in shale or black sands, prompted this investigation. The Bureau desired that materials containing as little as 60 p.p.m. of uranium be assayed within reasonable limits of accuracy. One of the primary aims of this work has been to eliminate, as far as possible, the necessity for repeated cup ferron extractions.

Jan 1, 1960

By Joseph Cervik, Gerald L. Finfinger

This Bureau of Mines publication reviews underground methane drainage pro- grams being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By Jr. Blake

This work was done to determine the technical feasibility of using the Pedersen process to produce cell-grade alumina and an iron byproduct from the high-silica and titania bauxites of the Pacific Northwest. Smelting of these bauxites with lime and coke at about 1,750° C in an electric arc furnace produced calcium aluminate slags in which at least 80 percent of the alumina was leachable by sodium carbonate solution. After a lime-desilication of the sodium aluminate leach liquors, neutralization of these solutions with carbon dioxide resulted in precipitation of an alumina hydrate of sufficient purity for calcination to cell-grade alumina. Recoveries of byproduct iron averaged over 90 percent; however, the iron contained about 1 percent phosphorous and would require additional refining. Additional small scale tests on these slags showed the following: (1) Titania had little effect on leachability if sufficient additional lime was added to form calcium titanate (CaO.TiO 2); (2) a slag containing about 14 percent silica required a slower cooling rate than one containing 7 percent silica for formation of high percentages of soluble aluminates; and (3) high-silica slags leached better at room temperature for long periods than at 65° C for shorter periods, but low-silica slags leached well by either method.

Jan 1, 1967

By Robert W. Smith

In a certain application2/ it was necessary to compute the beta function B(p, q) for a certain set of values p and q. Since t he set of p and q values was much mo re finely spaced than those in any published tables, the authors decided to make their results available in this report. In connection with this application the functionB(p, q) was needed at various points in the p, q plane at intervals of 0.05, 0.05<p = q< 10.00. Fletcher, Miller, and Rosenhead2/ state that the only tables available in the desired range are those of Rearson.4/ However, the interval used by Pearson was not small enough for the present application. For this reason it was decided to calculate B(p, q) for p = q =0.05 (0.05) 10. 00.2/ This table is published because of the fundamental importance in mathematical analysis of the complete beta function.

Jan 1, 1953

By Frank J. Perzak

This report describes a U.S. Bureau of Mines study on the hazards of large-scale conveyor belt fires in underground coal mines, as a function of both air velocity and distance from belt surface to gallery roof. The fire hazards considered were smoke obscuration, toxic effects of carbon monoxide (CO), and elevated air temperatures downstream of the fire. All of these hazards scale with the ratio of fire intensity to ventilation airflow. These hazards were all found to be greater at the lower belt-to-roof distance, owing to the greater fire intensities that resulted. The hazards of smoke obscuration and elevated CO levels were greater at lower air velocities. Smoke obscuration was found to be the earliest hazard, reaching critical levels before the stage of belt flame spread. Critical levels of CO and downstream air temperatures were not reached until the later stages of flame spread. Fire growth rates during rapid flame spread were much greater than rates measured during the early stages of belt burning. Data were analyzed to determine the early-warning capability of fire sensors. Smoke sensors provided the earliest warning, followed closely by CO sensors. Thermal sensors did not exhibit any early warning capability.

Jan 1, 2010

By Patrick D. Plumb

The Bureau of Mines (BOM) has begun a project to increase the understanding of the relationships between ecosystem health and its functions, and minerals development. The BOM, Juneau Branch, Alaska Field Operations Center, is providing support for ecosystem based land-management decision-making and the development of ecosystem based regulations by documenting the effects of mining on ecosystems and demonstrating the tools used to assess and analyze those effects. This is done by reviewing the data available on ecosystems and the environment at a mining site, the Greens Creek Mine near Juneau, Alaska, and applying available Geographic Information System modeling tools to assess the impacts of the mine on components of the pristine ecosystem. Habitat Capability Models for wildlife indicator species are used in this examination. Wildlife indicator species are used as indicators of ecosystem health by the U.S. Forest Service and the Alaska Department of Fish and Game, who developed these models for southeast Alaska. Analysis techniques from the U.S. Fish and Wildlife Service&apos;s Habitat Evaluation Procedures (HEP) are also used in this report. By applying available models and analytical techniques to the Greens Creek area, the benefits gained through mitigation of potential impacts become apparent. These or similar techniques are useful for cost/benefit analysis of mitigation alternatives. Also apparent from this analysis is that the degree to which potential impacts are observable will depend upon the ecosystem scale considered. This demonstrates the importance of defining the ecosystem and scale before performing impact and cost/benefit analysis. The watershed scale is found to be useful for assessing impacts to ecosystem components at the Greens Creek Mine. Much progress remains to be made in the modeling and prediction of impacts to ecosystems from mining activity.

Jan 1, 1994

By Franklin D. Cooper

Three model dwelling units were redesigned to achieve specific levels of noise reduction above that provided by conventional construction. Using 1968 prices, the added costs of materials and installation were found to range from $500 to $5,000 depending upon the size of the dwelling unit and the degree of insulation. The potential aggregate expenditures for sound insulation materials are projected to reach $617 million in 1975, including about $408 mil- lion for the mineral-based materials, in 1968 constant dollars. The report includes a brief review of the mechanics and effects of sound.

Jan 1, 1970

By Hillary W. St. Clair

This report describes an experimental method for determining parameters for the rate of reaction of CO2 with solid carbon. The method involves the simulation of a flow reactor by a mathematical model based on a hypothetical multistage reactor which permits calculation of the analyses of effluent gas and carbon consumed as functions of the flow rate and duration of the reaction. The method is applied to experimental data on the reaction of coke with CO2 in fluidized-bed and fixed-bed flow reactors. A method is described whereby two parameters may be determined simultaneously. The method involves a reiterative procedure that finds the values of the parameters that minimize the sum of squares of deviation between calculated and observed analyses of the effluent gas.

Jan 1, 1971

By Gary L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from low-grade domestic chromites, which contain silicon and aluminum impurity levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten sodium hydroxide (NaOH) under oxidizing conditions to form sodium chromate (Na2Cr04). The reaction product is leached with methanol to remove the majority of the unreacted sodium hydroxide, then with water to remove the sodium chromate and the remainder of the sodium hydroxide. The sodium chromate product is recovered by evaporative crystallization from the aqueous solution. This report presents results of laboratory tests to determine the optimum fusion conditions and the chromium extractions obtained from several domestic chrotdte concentrates. These concentrates are from a variety of sources, including the Stillwater Complex in Montana, Kanuti River-Caribou Mountain, Red Bluff Bay, Kenai Peninsula, and Kodiak Island areas in Alaska, deposits in northern California, and a nickel-cobalt laterite from southern Oregon. All of these concentrates were successfully treated by the Bureau procedure. The best chromium extrac-tions obtained for each of these materials ranged from 69.5 to 98.9 pet.

Jan 1, 1985

Southeast Alaska&apos;s mining industry has come to life after nearly 50 years of relative dormancy. Commencement of operations of the Greens Creek Mine in 1989 marked a turning point in the industry as the first large scale mining operation in the region since closure of the Alaska-Juneau Mine in 1944. The Greens Creek Mine is now the nation&apos;s largest silver producer. Other large scale mining projects are now on the drawing board, including development of the Kensington Mine and reopening the Alaska-Juneau Mine, which could become North America&apos;s largest underground gold mine. The region&apos;s mining industry includes more than these large scale projects, however. For example, a significant level of mineral exploration occurs each summer in Southeast Alaska. In addition, mining operations in British Columbia and Yukon Territory are generating jobs and income in Southeast Alaska.

Jan 1, 1992