Search Documents

By Roy L. Grant

The Bureau of Mines investigated the up-and-down method with factorial designs to determine if shorter, and therefore less costly, trial sequences could be used. Although sequences of 50 trials are usually recommended, sequences of 20 trials were arbitrarily chosen for the experiments with permissible coal mine explosives described in this report. These explosives were fired from a cannon pointed into a flammable natural gas-air atmosphere at the Bureau of Mines Explosives Research Center gallery to ascertain their safety properties. The investigation demonstrated that the shorter sequences led to useful conclusions with a reduction in cost of the experimental program.

Jan 1, 1967

By Gopala N. Krishnan

The most promising candidate for the recovery of alumina from non-bauxitic sources is the leaching of clay by HCL acid followed by crystallization of aluminum chloride hexahydrate (ACH) by hydrogen chloride sparging. Hydrothermal precipitation of boehmite ( ?-A100H) from aluminum chloride solution will simplify the process, will reduce energy consumption and will eliminate corrosion problems involved in calcination of ACH to obtain alumina. This report summarizes the results of Phase I of a program to study the precipitation of boehmite from AlC13 solutions. The amount of boehmite precipitation from dilute A1C13 solutions (5 wt%) is . negligible below 200°C. Above 200°C the precipitation increases with increasing temperature approaching 40% at 300°C. Addition of HCl acid to the dilute A1C13 solution even in small quantities drastically reduces boehmite precipitation. Solution impurities such as Fe, Ca, Mg, or Na substantially promote the precipitation of boehmite. No precipitation is observed from concentrated A1C13 solution (30wt%) representing the leach liquor.

Jan 1, 1980

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

By A. B. Hooker, J. W. Paul

"There was a time when any suggestion that the Davy flame (safety) lamp be discarded, would have evoked unlimited, criticism. However, that time is past.Investigations both here and abroad have shown conclusively that the Davy lamp does not have the necessary factor of safety against ignitions of mine gas, and England, the lost stronghold of the Davy lamp in Europe, has eliminated this lamp and substituted safer types.In the United States there are companies who still use the Davy lamp in spite of all that has been said and published as to the dangers connected with its use.Recently the purchasing agent of an anthracite coal company requested the Department of the Interior, Bureau of Mines, to pass upon the safety of some braise gauzes for use in a shielded Davy lamp. A shielded Davy lamp is an ordinary Davy safety lamp equipped with a circular brass shield that is attached to the lamp posts. This shield extends about one-half way around the gauze and one-half of the gauze height. The main purpose of the shield is to prevent the lamps being extinguished by a sudden increase in the velocity of the air current past the lamp.The brass gauzes submitted for this test represented two grades of brass - a yellow brass and a red brass. The analysis of these brasses was not determined. Two shielded Davy lamps that were submitted for the tests each had a steel gauze. These steel gauzes were also tested. Tests were made in horizontally moving mixtures of Pittsburgh natural gas and air at velocities of 400 to 1,000 feet per minute. The gas percentages used were 7%, 8.6%, and 11%. Tests were made with the lamp shield in two positions relative to the lamp and direction of flow of the gas-and-air mixture. In one position the shield was between the gauze and flow, as normally used. In the other position the shield was on the downstream side of the lamp. The tests were continued until one or more failures or gas explosions been obtained with each of the six gauzes. The results of these tests summarized as follows:"

Jun 1, 1923

By J. E. Chilton

Interim performance specifications are presented for carbon monoxide, methane, and air velocity transducers used in the Bureau of Mines intrinsically safe mine monitoring system. These specifications give quantitative values or qualitative descriptions of the transducers, including environmental parameters and monitoring system measurement and maintenance requirements as recommended by the Bureau of Mines. Commercially available transducer modules and prototype modules are listed together with selected characteristics.

Jan 1, 1983

By V. R. Spironello

The Bureau of Mines is conducting studies of the slags related to ferrous technology to evaluate acceptable substitutes for the auxiliary flux, mineral fluorspar, in foundry operations. This work is directed toward the Bureau's goal of minimizing the Nation's dependence on scarce and critical minerals Comparative basic practice cupola (18-inch-ID) trials were made to evaluate a waste material called "used potlining," which contains significant levels of fluorine, sodium, and aluminum in various compounds. Used potlining is recovered from alumina reduction cells after its useful life, and was supplied by the Aluminum Co. of America (Alcoa) to the Bureau for evaluation. The material in the lump and pelletized form (with limestone) provided extremely fluid slags based on visual observation during cupola operation. No adverse effects were found on cupola performance, metal and slag chemistry, the environment, or mechanical properties of the castings produced. Fluorine recovery in the slag was equal to, or higher than, that of fluorspar; fluorine losses to the scrubber water and solids were lower. The acidity of the scrubber Hater was somewhat neutralized. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag and visual inspection. The recovery of sodium in the slag, presumably as the oxide, significantly increased slag fluidity, suggesting that less than equivalent fluorine may be required. There was no contamination of the gray iron by the aluminum from the used potlining. Used potlining was completely satisfactory as a substitute for fluorspar in cupola ironmelting.

Jan 1, 1981

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high-and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country. Information that would improve coverage and accuracy of the next revision of the publication will be welcomed by the Bureau of Mines.

Jan 1, 1966

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high- and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country.

Jan 1, 1966

This publication summarizes the Bureau's activities as part of a study of the Juneau Mining District (JMD) during the period 1984-1988. The objectives of the program were to identify the type, amount, and distribution of mineral deposits in the district, determine ore reserves, study beneficiation technologies for the ore, make feasibility studies, and address economic and legislative effects on mineral development. The JMD study was a cooperative study involving the Bureau and the Alaska Division of Geological and Geophysical Surveys (ADGGS). Over 30 employee-years were spent by the Bureau on this project. Bureau investigations in the JMD consisted of a district-wide investigation of industrial materials in addition to site-specific investigations of precious and base metals in five subareas. During the 4 years of the JMD study, more than 300 areas, mines, prospects, and occurrences were visited, which contain gold, silver, copper, zinc, lead, nickel, cobalt, tungsten, molybdenum, chromium, and platinum group metals (PGM). More than 59,000 feet of underground workings were mapped and sampled. More than 5,500 samples were taken; one diamond drilling program and three geophysical surveys were completed. An up-to-date and complete mineral data base for the JMD did not exist prior to this study. The JMD study, which coincided with a tremendous increase in mineral interest and activity in the district, has proven to be valuable to both the minerals industry and land management agencies. The discovery of two new mineral occurrences and compilation of data on known mines, prospects, and occurrences have aided industry activity in the region. The study enabled timely data to be available to land management agencies at the Federal, State, and municipal levels.

Jan 1, 2012

By Michael R. Norland

Surface and subsurface stabilization of mining-related wastes through revegetation depends upon the physical, chemical, and biological condition of the waste following mining. Mining disturbances can significantly alter the soil physical, chemical, and biological characteristics of a site, reducing or eliminating mycorrhizal fungi from the soil. Mycorrhizae are economically and ecologically important because they can alleviate environmental stresses caused by lack of proper soil condition and because they are vital to stabilization of mining waste by increasing plant survival and biomass through increased nutrient and water uptake. This report discusses some of the ecological factors that may affect mycorrhizae-plant associations on mining-related wastes and provides general information on mycorrhizae inoculation technology.

Jan 1, 1993

By R. L. Handy

The goal of this research was to adapt the highly successful rock borehole shear test for use in deep, small-diameter boreholes. Operating somewhat on the principle of a rock bolt, the borehole shear test measures both the expansion pressure and pulling force to give discrete measures of rock shearing strength as a function of the applied normal pressure. A new instrument was designed and built to fit into a 2-3/8 inch diameter hole. Unfortunately the design became so complicated, the operation is nut reliable. This is attributed to constraints of the small hole, and added requirements of an in-hole anchor to push against, and a rotating shear plate cleaner for repeated tests down-hole. A clue to the d: vice complexity is its length, which is over 10 feet. Furthermore it employs concentric cylinders and one hydraulic cylinder bored into the piston of another, or it would be even longer. Meanwhile drilling technology has advanced to greatly reduce costs of drilling 5- or 6-inch diameter holes. The downhole tester therefore should be redesigned and simplified for use in a larger diameter drill hole.

Jan 1, 1982

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all mineral to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of force applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective. A consideration of the possibilities of such a method for crushing led to some experimental work of a preliminary nature, the results of which are embodied in this paper. No systematic program was followed in the work and the results are, therefore, not final and far from complete. The success attained so far, with the mediocre apparatus available seems to warrant a preliminary report, with the expressed hope that the work may be carried on as well-outline program covering such phases as have been impossible to investigate at this time.

Jan 1, 1931

From time to time the Bureau of Mines has interpreted and applied certain provisions of the Federal Coal Mine Safety Act and Federal Mine Safety Codes, primarily for the guidance of Federal Coal Mine Inspectors. Although interpretations of the Act have appeared in the Federal Register, the Code interpretations and practical applications have not been published. In response to many requests from representatives of the coal-mining industry, the Bureau is publishing this information to promote better understanding of those provisions that may be misinterpreted or misapplied. INTERPRETATIONS AND APPLICATIONS Two Federal Mine Safety Codes are discussed in this report, namely the Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States, Part 1, and the Federal Mine Safety Code, Anthracite Mines of the United States, Part 1. In this circular the word Codes refers to both directives; Code* refers to the code for bituminous-coal and lignite mines; Code? refers to the one for anthracite mines. Act* refers only to bituminous-coal and lignite mines.

Jan 1, 1963

By M. M. Wong

A brief investigation was made to determine the feasibility of electro-refining beryllium in a KCI-LiCI-BeC12 bath. Thin, platelike crystals of beryllium metal were produced by electrolyzing technical-grade beryllium metal beads (about 94-percent purity) as the soluble anode. Operating cell conditions were: Temperatures of 450° to 600° C.; an inert atmosphere; bath compositions of (1) 38.1 mol. percent KC1, 54.8 mol. percent LiCl, and 7.1 mol. percent BeC12 and (2) 36.7 mol. percent KC1, 52.7 mol. percent LiCl, and 10.6 mol. percent BeC12; cell voltages of 0.30 to 0.80; and initial cathode current densities of 50 to 435 a./sq, ft. Current efficiencies ranging from 87 to 96 percent were obtained. Qualitative spectrographic analyses of the metal products indicated that impurities were reduced. This technique offers the possibility of producing a grade of beryllium purer than that now generally available, which may have better mechanical properties.

Jan 1, 1960

By Charles L. Kimbell

Comprehensive world mineral industry investment data do not exist, but limited material published on aggregates of in vestment in some elements of the world mineral industry suggest a continued up-turn in the investment level, at least in market economy countries in 1989. Steel industry investments in Organization for Economic Cooperation and Development (OECD) countries are not yet available for 1989 but, as shown in table 6, increased by 22.1% in 1988, after showing a decrease of 5.2% (revised) in 1987. The pattern of investment ups and downs varied during 1988 within country blocs and economic alliances showing no particular trends. Investment in the steel industry by the United States increased by 58.3% between 1987 and 1988 and was 1 1.9% higher than the previous highest amount invested during the 1984-88 period but was still 41.5% less than the amount invested in 1983. Investment in the steel industries of the European Coal and Steel Community (ECSC) dropped again in 1988 from the revised amount for 1987, which became the first drop after several years of steady growth in what became the expanded ECSC in 1986. This drop in 1988 was the result of lower investments by Denmark, France, the Federal Republic of Germany, Ireland, Italy, Luxembourg, the Nether- lands, and Spain, investments grew or remained level in Belgium, Portugal, and the United Kingdom in 1987 and 1988. A decrease in investment in the Canadian (-26.6%) steel industry was offset by in- creases registered by the members of the European Free Trade Association (EFTA) of 31.7%, by Japan of 19.8% by Turkey of 22.4%, and a slight increase by the nations of Latin America. If data for the world steel industry as a whole, including those of the centrally planned economy countries, were available, the same pattern presumably would be shown as that reported; that is, it would remain fairly stable, with increases in some countries being offset by decreases in others. However, the lack of comprehensive information on the centrally planned economy countries makes it impossible to determine whether the overall trend was up or down despite recorded increases or decreases in production of the materials involved. Preliminary data show that investment levels in industries dealing with the production and/ or processing of mineral commodities for

Jan 1, 1992

By W. K. Overbey

Surface fracture trace density, changes in roof rock type, and topographic unloading due to drainage were mapped for the mining areas located in the Blacksville-Osage, W. Va., quadrangles to investigate their influence on mine roof falls. Using these factors, a technique was developed to predict probable roof fall areas ahead of projected mining operations. As a feasibility test of this proposed technique, areas were delineated where one, two, and all three of these factors were operating to formulate a "potential hazard map" for comparison with roof fall observations that were made. The limited evidence suggests that in combination these factors are reliable predictors of where roof falls are likely to occur. This technique promises to be a useful tool in planning mining operations.

Jan 1, 1973

By L. B. Berger

In this investigation, the ampoule type of carbon-monoxide (CO) detector which is manufactured under license of U. S. Patent 1,644,014 (October 4, 1927) was tested for sensitivity and reliability. This detector was devised primarily for examining the air of manholes and sewers for possible dangerous contamination with CO before workmen enter these places, but due to the simplicity of the device it may have a more general usage for examination of atmospheres which are known or suspected, to be contaminated with CO. Some of the suggested uses are the examination of the air in garages, tunnels, mines, around blast furnaces, gas plants, and in the home.

Jan 1, 1930

By P. R. Miles, J. K. H. Ma, J. Y. C. Ma, L. Bowman

"The bisbenzylisoquinoline alkaloids are compounds which can be isolated from plants and which exhibit a broad range of pharmacological activities. Perhaps the best known alkaloid of this group is tetrandrine (TT), a compound isolated from the root of a traditional Chinese medicinal herb, Stephania tetrandra. It has been tested for its effects on the cardiovascular system, tumors, and the lungs. For example, tetrandrine has been shown to act as a calcium entry blocker in cardiac sarcolemmal vesicles (King et a/., 1988) and has been used in China as a treatment for angina and hypertension. Its possible effects as a tumor-inhibitory substance have also been investigated (Kupchan and Atland, 1973). In addition, there are several lines of evidence to suggest that it is a possible therapeutic agent for the treatment of silicosis. Yu et a/. (1983) have shown that TT inhibits the development of experimental silicosis in rats when it is administered orally after intratracheal instillation of quartz. Other studies have shown that the alkaloid inhibits the synthesis of collagen by fibroblasts and the formation of silicotic nodules in rats exposed to silica (Huang et al., 1981; Liu et al., 1983). In fact, tetrandrine has been used clinically in China as an antifibrotic agent and has been shown to improve both the appearance of chest radiographs and the measurements of diffusing capacity in patients with silicosis (Li et al., 1981).Since tetrandrine may have a potential use as a therapeutic agent for fibrotic lung diseases, its effects on various pulmonary cells and tissues should be studied. Alveolar type II cells are located in the alveolar regions of the lungs and are important because they are responsible for the synthesis and secretion of pulmonary surfactant (Dobbs et al., 1982; King, 1984), regeneration of the alveolar epithelium after lung injury (Kauffman et al., 1974), and metabolism of foreign compounds (Bend et al., 1985). Furthermore, in silicosis, for which TT has been suggested as a treatment, there are increased amounts of pulmonary surfactant produced (Dethloff et al., 1986a,b) as a result of increased rates of surfactant synthesis by type II cells (Dethloff et a/., 1989; Miller et al., 1988). Because type II cells play a critical role in maintaining normal lung function and because type II cells are affected in silicosis, for which 'TT has been used as a treatment, we studied the effects of tetrandrine on energy metabolism in these cells in vitro. Energy metabolism was chosen because it is a basic cellular function which is neces-sary for other cellular processes to occur. Since type II cells depend on mitochondrial metabolism for energy production (Fisher et al., 1980), we examined the effects of tetrandrine on cellular and mitochondrial ATP production and oxygen consumption. Additional experiments were performed in an effort to determine if intracellular calcium levels may be involved in the TT-induced effects. A preliminary report of those results has appeared previously (Ma et al., 1991)."

Nov 1, 1995

The contractor examined L.T. White's Patent No. 3524680 and, finding it in need of engineering refinements, proceeded with a conceptual design of a variable wall mining machine. The contractor then proceeded to assess the feasibility of the variable wall mining machine measured against the criteria specified by the U.S. Bureau of Mines. The feasibility was judged from a physical aspect, a health and safety aspect, and an economic aspect. The Variable Wall Mining Machine was judged to be feasible on all three aspects provided that certain specified practices were adopted. Description The specifications and design and performance parameters of the Variable Wall Mining System as conceptualized are summarized in Tables I and II. The system consists of a side-cutting auger operating in a string of identical 12 ft. sections, along a 500 ft. retreating longwall face. In addition to the 41 identical sections, there is a special drive and discharge section at the head gate.

Jan 1, 2012

A working understanding of present coal mine communications equipment and its usage is an essential prerequisite to the determination of future communications systems needs. As a means of gaining this understanding, a field survey program was planned and implemented. The plan formulated called for obtaining both qualitative and quantitative data from three main areas of interest: the types, physical condition, and performance characteristics of equipment presently used in the sample of mines to be visited; the relationship present communications has to safety and productivity; and the practical, future communications needs as de- rived through interviews with present mine management. In compliance with the original plan, the type and physical condition of equipment in use was found through at-mine interviews of personnel responsible for installation and maintenance. Further evaluation was made through the review of equipment instruction books and maintenance manuals and through in-mine inspection of communications equipment and signal distribution networks. The performance characteristics were determined through listening to conversations and noise levels and by talk-testing from randomly selected stations throughout each mine. System operation was evaluated by asking communication system users their opinions and by noting any difficulties personnel had using the systems. Plans in the second area of interest--that of relating communications to mining operations-- were to observe mining operations and usage of communications; to gain insight through interviews with mine management, from mine superintendents to section foreman; and to look for correlation between communications, production, and safety. Lastly the communication systems needs and requirements were determined from first hand interviews of mine personnel, from the analysis that lead to the individual reports on the eight mines, and from an overview of all of the mines studied. The latter was done to find commonality between the needs of the individual mines such that system requirements having the greatest universal value could be derived, thus lowering per-mine cost of equipment through economics of scale. Armed with tape recorders, backgrounds in communications technology, and with an interview questionnaire that was improved as experience was gained, engineers visited the eight mines to obtain the raw data from which the needs and requirements could be developed through analysis. During the first part of the program two days were spent at each mine so that interviews and tours could be completed, and so that full eight hour shift phone usage recordings could be obtained for statistical analysis. One day visits were sufficient for those trips where tape recordings were not made. During the later trips less attention was given to the statistical nature of communications, and more to how communications relates to the total mining operation.

Nov 15, 1974