Search Documents

By R D. Lama, A Misra

One of the major factors restricting an increase in the productivity of a longwall mine is lower productivity obtained in a development panel. There has been a significant improvement in gate road development, particularly in mines requiring high density roof and rib bolting within 2 m of the face. Advance rates have increased from an average of 3 m to 5 m per shift in 1985 up to an average of 5 m to 10 m per shift in 1991. In mines at shallow depths with reasonably good conditions the increase has not been that significant. Advance rates have increased from an average of 7 m to 12 ni per shift in 1985 to an average of 12 m to 15 m per shift in 1991. Compared to the United States' (US) development rates, these are much lower. Extensive research work has been carried out to minimise cutting, wheeling, support setting time, and to optimise pillar length to achieve maximum advance rates. Pillar optimisation is very important in order to expedite adverse rates. This paper investigates various development rate technologies, both present and future, and optimises pillars to improve these dev elupment rates. Pillar optimisation is based upon time and motion studies conducted at mines in the Illawara region of New' South Wales, Australia, and the basic tools of arithmetic.

Jan 9, 1996

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992

By S. Vardy

The paper notes that the extraction of 22% of the remaining workable reserves in the north western area involves a risk of spontaneous combustion higher than is normal in Britain. Mining systems have been tailor made in order to minimize the risk of spontaneous heatings, and these systems are described. Well-proved methods of combating spontaneous combustion are referred to, as well as the limitations which now apply to them as the result of the introduction of modern mining techniques. A substantial part of the paper is devoted to the circumstances in which spontaneous combustion occurs underground in the north western area. Several actual incidents which have occurred in the last few years, along with the practical application of the lessons learned, are described. Of particular note are: a) the procedure adopted in the north western area to equalize pressure differences across stoppings using pressure chambers, and b) a retreat mining system, primarily designed to deal with high methane emission and steep gradients, which also affords some protection against spontaneous combustion.

May 23, 1905

By M. J. Howes

The high degree of mechanisation, which is mainly diesel-powered, has a significant effect on heat loads; heat output from this source often exceeds the heat flow from the surrounding rock. The extensive use of diesel-powered equipment also influences ventilation rates and minimum values are necessary to ensure that emissions of diesel exhaust are adequately diluted. Many Australian mines are in subtropical or tropical areas with high ambient wet- and dry-bulb temperatures on surface. This, coupled with the large amount of heat from mechanisation, usually means that refrigeration is required at much shallower depths. A secondary problem is associated with the definition of acceptable thermal environment conditions, which are sometimes based on the assumption of no air movement. This gives rise to very stringent thermal environment acceptance criteria, which, in some areas, would prohibit work on surface, let alone underground

Jun 12, 1905

"The Archaean komatiite-associated nickel sulphide deposits at Kambalda, Western Australia, exhibit a number of stratigraphic features that are indicative of a strong volcanic control on ore localization, including (1) a restriction to specific basal cumulate metakomatiite host units, (2) confinement within distinctive synvolcanic embayments in the footwall and (3) variations in the internal structure and composition of overlying and adjacent barren metakomatiite flow's and the distribution of interflow metasediments with proximity to the ore zones.The high magnesium content of the host units (up to 45% MgO volatile-free) in comparison with that of aphyric or spinifex- textured lavas (16-32% MgO) has been considered previously to indicate either magmas/lavas rich in intratelluric olivine or selective accumulation of olivine phenocrysts. The marked linear trend of the oreshoots, basal host units, footwall embayments and the volcanic stratigraphic relationships have been used as evidence for local linear feeding fissures. Rare relict igneous olivine in some host units is, however, demonstrably not intratelluric, and there is no direct or indirect evidence of a proximal eruptive site (e.g. footwall feeders, pyroclastic breccias, ultramafic intrusives) at Kambalda such as at some other deposits of this type. Kambalda is interpreted as a distal rather than proximal volcanic environment.Emplacement of the komatiite sequence at Kambalda was probably controlled by the locations of a few specific eruptive sites relative to regional topographic gradients and influenced by the topography of the pre-existing volcanic surface. Olivine enrichment in the basal host units occurred by in-situ fractionation and cumulus crystallization of olivine during longitudinal lava flow within linear lava conduits, possibly centralized on depressions between non-overlapping footwall basalt flows. The distinctive stratigraphic relationships are attributed to localization of lava conduits along the volcanic pitchline, flanked by more slowly moving parts of the flows. There are analogies with the physical volcanology of Modern basaltic and Proterozoic komatiitic lava flows.A corollary of this model is that the lava conduits thermally eroded and assimilated sulphidic sediments, contributing additional sulphur to sulphur-saturated komatiites or possibly inducing sulphide separation in originally sulphur-undersaturated komatiites. The latter would account for the restriction of ores to linear cumulate komatiite host units (thermally active lava conduits) and the locally mutually exclusive, but stratigraphically equivalent, relationship between the ores and sulphidic metasediments at Kambalda."

Jan 1, 1984

By R. M. Honey

An attempt is made to summarise the mining law of England, Wales and Scotland. Attention is also drawn to the recent privatisation of the electric power and gas industries and the intention of the present Government to follow suit as regards coal mining. The subject of mining law is discussed under the headings: minerals or rights that have been nationalised or are vested in the Crown; ownership (of land and mineral rights); special customs; tracing of owners; right of support (arising from mining); ancillary rights and easements; obtaining prospecting and mining rights; planning permission; statutory aids to obtaining rights; notes on the history, law and practices of petroleum (onshore and offshore), gas, coal, prescribed substances, gold and silver; electricity; safety, health and welfare; and technical information and boreholes. A correction in the subsequent issue amends errors on p.A75 and A82 and regrets the publication of misinformation on the availability of grants

May 1, 1991

By I S. Lowndes, K. Moloney

Diesel powered equipment is currently used extensively in mining and tunnelling operations around the world due to its mobility, flexibility and through selective application to enhance productivity. However, the increased use of diesel equipment has exacerbated the pollutant load (including heat, humidity, exhaust gases and particulates) placed upon the environmental systems of many underground operations. This expansion in the use of diesel equipment has prom pted researchers to evaluate m easure ment and control technology. This paper reviews the recent research conducted in various countries.

Jan 10, 1996

Jan 1, 1947

By C. H. J. Beaven, M. P. Jones

Since the various new techniques of automation and computing have enabled vast numbers of mineralogical observations of relatively small samples to be made cheaply and rapidly, the statistical assessment of these measurements has become of vital importance. Much of the theory and most of the procedures of sampling that are used in the mineral industry are based on Gaussian statistics, but modern measuring techniques show that many mineralogical parameters do not necessarily follow the Gaussian distribution function. Consequently, it has become necessary to examine the application of other, more suitable statistical methods in order to derive the maximum amount of useful information from the examination of mineralogical samples. Some of the errors that can be introduced by the use of incorrect distribution functions are discussed and the value of determining the function that is appropriate to the particular parameter that is being measured is shown. Examples are provided of non-Gaussian distribution functions in mineralogical materials that were encountered during prospecting and during mineral treatment operations: a Canadian uranium ore, a Thai tin ore, and gold ore tailings.

Dec 1, 1971

By C. P. Summerhayes, J. W. G. Gilbey, S. Henley, G. P. Glasby, J. J. T. Harvey, J. Larsson, O. Akiman, A. G. Brown

Abstracts are presented from six University of London, one University of Nottingham and one University of Durham PhD theses

Dec 1, 1971

By B. Sonmez, B. Aksanl, S. Ersaym, I. F. Erkal, S. L. Ergun

The comminution circuit at the plant has experienced severe problems arising from a feed containing much larger amounts of clay and having a higher moisture content than expected. Three solutions were proposed: replacement of the crushing circuit by tooth roll-type crushers; using washing drums; and introducing primary autogenous/semi-autogenous millling instead of crushing. Computer simulations studied the effects of the first two solutions on the circuit capacity. Laboratory and industrial scale ball mill batch grinding tests were carried out. The parameters of a kinetic model were determined. The ball mill circuit was sampled and operating model parameters were calculated. The ability of batch grinding parameters to represent the operating conditions was studied. Tests failed to find acceptable model parameters, but parameters from an industrial size batch mill were found to be suitable for simulation studies. The simulations indicated that a continuous feed of -12 mm provided by tooth roll crushers would maintain the desired capacity. Increasing the feed size to -25 mm would reduce the capacity by 8-15%. The use of washing drums could also solve the capacity problem, but small fluctuations in water flow rates might result in problems of excess water in the grinding circuit.

Jan 4, 1993

By Evans E. C.

At first sight, the extinction of a mine fire by the action of some such gas as carbon dioxide would appear to be quite a simple and practicable operation. From a consideration of the theoretical aspects only of the question, it becomes evident that the matter is not so simple as it appears to be at first sight. The fire at the Senghenydd Colliery occurred as the result of the disastrous explosion of October 14th, 1913. This explosion was confined to the west side of the colliery; and as a result the timbers in the main intake on this side were set on fire; but these were soon buried beneath falls, and the tire continued under them. Attempts were made to extinguish it with water, with the aid of chemical extinguishers, and by digging it out; hut these had to he abandoned, and ultimately the fire-zone was sealed off by “ bashings” (stoppings). By December, progress in the decrease of combustion was so slow that it was decided to try the effect of inert gas. The installation, control and operation of the carbon dioxide plant and associated water-gauge are described in detail and conclusions drawn for the extinguishing of mine fires by CO2

Dec 1, 1916

By Tuncel M. Yegulalp, Selamet G. Ergelebi

A description is given of a method of analysing modern mining systems in terms of reliability and their effects on productivity. Non-exponential distributions, such as the Weibull and lognormal distributions, for failure and equipment repair times are also considered. The resulting non-homogeneous Markov process is solved by the method of stages. A longwall mining system is analysed as an example.

Jan 4, 1993

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992

By E. C. I. Hammerbeck

"Geological controls and constraints in space and time define the milieu of the nickel deposits of Southern Africa. Primary, magmatic deposits are of two types, e.g. synvolcanic or syntectonic deposits confined to certain orogenic domains, and those related to intracratonic, post-orogenic magmatism, e.g. the Great Dyke, the Bushveld Complex and the Insizwa intrusion. Epigenetic and supergene deposits form a separate, unrelated group and are of minor economic importance.The metallogenic evolution of syntectonic nickel deposits is particularly well illustrated in the Zimbabwean Province, where the relationships between Archaean greenstone development and nickel mineralization are best illustrated. Volumetrically subordinate, nickel-poor greenstones in the 3500 m.y. old Sebakwian Group are followed by more common komatiite development in the Lower Greenstones (3000 m.y.), and, finally, by very significant komatiites with important nickel mineralization in the 2700 m.y. old Upper Greenstones of the Bulawayan Group. Comparable nickel mineralization is not known in the Raapvaal Province, in spite of ubiquitous komatiitic magmatism of the Onverwacht Group (3500 m.y.) and other greenstone sequences. No komatiitic rocks younger than about 3200 m.y. are known in this region, orogenic activity in the Kaapvaal tectonic province having ceased at about 3100 m.y., whereas the Zimbabwe Province remained tectonically active until at least 2600 m.y.The tectonic environment, host-rock petrology and mode of emplacement, as well as some details of the nickel mineralization, are the parameters employed to classify the Southern African magmatic nickel deposits. A rating of the deposits is introduced that reflects the original resources of the deposit, its average nickel content, its mining history and potential to facilitate ready comparison with and assessment of the nickel deposits listed in the classification, as well as some important nickel deposits worldwide."

Jan 1, 1984

By S. G. Tsimas, A. K. Moutsatsou, S. G. Tsivilis, G. K. Parissakis

(NH4)2SO4 can be used with success as a leachant to remove gypsum contained in celestite ores. The process, which is applied before flotation, provides an upgraded feed and problems related to the simultaneous flotation of CaCO3 and SrSO4 are reduced. The process is independent of the gypsum content of the feed so that each leaching stage decreases the gypsum content by almost 50%. The use of (NH4)2SO4 has an insignificant effect on the co-leaching of SrSO4 (0.45 wt.%) at each stage

Jun 13, 1905

By I. A. Scott, T. J. Napier-Munn

Size-by-size partition curves for mineral separation in dense-medium cyclones pivot about a single characteristic point. This is defined for stable, non-segregating media by the medium density and the proportion of the medium reporting to the underflow. The pivot point departs from these values for unstable, conventional media. The phenomenon can be represented by an equation with two parameters defining pivot point coordinates and two the Ep value. On the basis of experiments in a 200 mm cyclone using ferrosilicon media, simple regression equations were developed for the separation parameters in terms of operating conditions (the coefficients were likely to be site-specific). The experiments successfully decoupled the effects of medium density and viscosity and showed that the value of Ep was independent of the former but strongly dependent on the latter. A classification model was used to predict the density of the underflow medium, a knowledge of which is required to determine the pivot parameters. The model correctly reflects the performance trends observed in dense-medium cyclone operation and has the potential to be generalised to a wide range of industrial practice.

Jan 8, 1992

The first part describes a model (the C model) based on the motion of the grinding charge. The charge is treated as a continuum, which allows analytical solutions to the equations that are developed. The C model is equally applicable to ball-, semi-autogenous and autogenous mills and contains a description of the power draw of both the cylindrical section and the cone-ends. Differences between the power draw of grate- and overflow-discharge mills are described from consideration of the different shapes and compositions of their charges. A large database of industrial mill data is used to demonstrate the accuracy of the model. Part 2 describes a simpler, empirical model (the E model) whose performance is based on that of the C model. The same database was used to assess the predictive capabilities of the E model. The model was shown to be only slightly less accurate than the C model despite its much simpler structure

Jun 18, 1905

By O. Dojcar

Equations for calculating the parameters of controlled blasting (burden and spacing of boreholes and weight of the bottom charge) are derived and analysed on the basis of empirical values and made more precise through incorporation of the properties of the rock being blasted and explosive applied. For the success of controlled blasting the correct choice of the blasthole diameter/charge diameter ratio is critical. This relation is defined as the coefficient of radial decoupling of the charge; it is recommended that it is chosen to be between 3 and 3.5. Analysis of smooth blasting, cushion blasting and presplitting indicates that cushion blasting is a less destructive alternative to smooth blasting, but it has a slightly higher blasthole consumption and limited possibilities of use. There are definite economic advantages to controlled blasting, especially in rock masses of low and medium strength

Dec 1, 1996

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Barclay, E. Rothery, S. H. White

Discussion by B.P.J. Stevens of the paper, published in Trans. IMMA, vol.104, 1995, p.B1-B17, is presented together with the authors' response. Stevens questions the authors' radically different interpretation of the structural geology of the Broken Hill Block, considering that the descriptive part of the paper is a useful addition but that the conclusions are unwarranted on the basis of the data presented. A number of major points of disagreement are outlined and half a dozen additional minor points listed. In response, the authors admire Stevens's contribution to unravelling the geology of the area but defend their attempts to take the regional studies a step further, pointing out that he has misquoted what they wrote and arguing that because of the assumptions underpinning the derivation of the present stratigraphy it cannot be used to constrain structural models. With regard to shear zones, they cite the extensive earlier literature and refer to horizontal displacements shown on maps produced by Stevens et al. Detailed discussion follows of the stratigraphy and of the stratigraphic correlation problems resulting from failure to recognise the presence and significance of shears, particularly those parallel to stratigraphy. The remobilised position of the Pb mineralisation in the North Mine open cut is reiterated. It is concluded that there is an urgent need for systematic isotopic dating in the area to constrain the stratigraphy

Apr 1, 1996