Search Documents

After the Loma Prieta Earthquake, which caused major damage to viaducts in the Bay Area, the California Department of Transportation set up a test programme for foundation piles. Funderingstechnieken Verstraeten B.V., beter known as Fundex, was approached, since one of the piling systems of Fundex, named Tubex, is extremely suitable in areas sensitive to earthquakes and we were very much interested to prove the capabilities of this piling system. Equipment For the installation of Tubex and Tubex grout-injection piles special piling equipment is required. Since our company is not only a contractor, but also a designer and manufacturer of piling equipment, all special equipment for our range of foundation techniques is designed and built by our own piling equipment department. For the installation of both Tubex piles and Tubex grout-injection piles for the Caltrans test programme, the following pieces of equipment were selected: a) Fundex F12 piling rig b) Drill table c) Hydraulic powerpack d) Grout mixing unit and high pressure pump

Jan 1, 1993

By J. M. N. P. C. Teles, Venda Oliveira P. J., Correia A. A. S.

"AbstractA laboratory work was performed to study the mechanical behavior of a Portuguese soft soil chemically stabilized with binders and reinforced with metallic fibers when subjected to tensile stresses. To this end and in order to compare the tensile strength results done by two different tests, there were conducted two types of experimental tests: Tensile Split Strength Tests (TS) and Direct Tensile Strength Tests (T). The samples tested had the same binder quantity and different fiber contents, which allowed the characterization of the tensile behavior of the stabilized and reinforced soil, as well as the definition of the best fiber content. Results show that the binder is the main parameter controlling the behavior of the stabilized and reinforced soil until failure, while the influence of the fibers is noticed mainly at the post-failure behavior. The comparison between the tensile strength done by T and TS tests shows that the tensile split test can be used to estimate the tensile strength, although its results are lower than those obtained by the direct tensile tests in general.IntroductionDue to its poor mechanical characteristics, the construction on soft soils presents difficulties that require the use of soil improvement techniques such as chemical stabilization. However, even when mixed with binders, the tensile strength of the stabilized soil is poor, requiring, in certain cases, the use of expensive steel reinforcement or metallic beams, with obvious impact on the final cost of the work. Thus, for the cases where the tensile strength is a design requirement, the soil stabilization should be design with another element, whose primary role is to give tensile strength to the improved soil (Teles 2013).To fill the lack of published studies focused on soft soils both chemically stabilized and reinforced with metallic fibers, the present research aims to analyze the behavior of the improved soil when subjected to tensile stresses. To support the research there were conducted direct tensile tests (T) to directly measure the tensile strength of the samples and tensile split tests (TS) or Brazilian tests to obtain it indirectly. The samples tested had the same binder quantity but five different fiber contents in order to study the influence of the fibers in the improved soil behavior. In addition, a comparison between the results of both tests was made."

Jan 1, 2014

By Stanley A. Schwartz

In the Piedmont, heavily loaded structures are generally supported by either drilled piers or one of several pile types. The choice of drilled piers or piles is typically one of comparative costs. The cost of a drilled pier foundation is usually the more difficult to predict because of the greater impact that variable conditions and construction monitoring have on cost. Poor specifications, related to the drilling equipment, procedures and bearing level, can also result in large cost extras. In the southern Piedmont, straight shafts are typically extended down to hard rock to achieve primary support in end-bearing: when bells are required, they are often constructed manually. In some eastern and northern Piedmont locations the thickness of the decompossed rock zone is significant and considerable skin friction can be mobilized. Typically piers are constructed in holes temporarily cased with steel liners. The bottom is cleaned of loose material and water, and then evaluated by a geotechnical engineer to confirm the design bearing pressure (and friction, where appropriate) or recommend alternative construction measures.

Jan 1, 1988

By Gang Guo, Zhong Liu, Yi Zhang, Jingchun Lu

"Abstract Application of soil displacement screw pile (known as SDS pile) has been experiencing accelerated growth in Chinese deep foundation industry because of its technical advantages, environmental benefits, and cost effective as well. As bored displacement piling, SDS piles are able to perform better than non-displacement piling such as CFA plies due to changing the stress state in the soil around SDS piles during the installation. Therefore the design methods between the conventional pile type and SDS pile type have some differences. Based on the methodology research, current Chinese piling rigs, displacement augers and piling projects are introduced, and the current design approaches for SDS piles in China are also described. Moreover, the design results are verified by using full scale load tests, and a part of the research results of SDS piling system acquired in China are presented.IntroductionThe Continuous Flight Auger Pile, also known as the CFA pile, has occupied about 22% in the pile market all over the world (Van Impe, 2004; Bottiau, 2006). The CFA piles are usually used for large diameter (600mm~1200mm) pile foundations and deep excavation projects. Whereas the small size CFA piles (400mm~500mm) are mainly applied for composite foundations in China. In the past 10 years, the new technology of soil displacement screw piling has been applied worldwide (Prezzi et al., 2005). And it is also extensively used for high-rise buildings, industrial plants and railway projects in China (shown in Figure 1)."

Jan 1, 2014

By Chris Harnan

This paper describes the geology of three European cities and outlines how the geology has lead to the development of specific foundation construction techniques. Comparative tables of techniques commonly employed are given in Section 5. It can be seen that despite the presence of the 'single market', techniques still have wide diversity despite some similarities in geotechnical conditions.

Jan 1, 2000

By Mike Muchard

Augered cast-in-place piles are one of the most cost effective deep foundation options available to designers but have been largely underutilized due to skepticism associated with quality assurance and hence capacity. When installed correctly, unit friction values can rival any other competing foundation system. To this end, many means have been implemented to increase confidence in the competence of the foundation. One such method is load testing via the Statnamic test method. This paper presents an overview of the Statnamic test method, advantages and disadvantages of its use, and several case studies where Statnamic testing of augered cast-in-place piles confirmed quality construction, brought about design changes, or proof tested problematic installations.

Jan 1, 2000

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

By Ken Andromalos

Continued population growth combined with limited water resources in the Denver area has resulted in the conversion of a number of mined out gravel pits in the area into municipal water storage facilities. The use of slurry walls provides a cost effective means of isolating groundwater to convert these pits into efficient water storage facilities. Design considerations include: stability, underlying bedrock conditions, backfill mix design and earthwork requirements. Installation issues during construction include: trench stability considerations when excavating through relatively clean sand and gravel deposits in potentially high groundwater conditions; keying into three to ten feet of fractured claystone, siltstone or sandstone that makes up part of the Denver formation, and quality assurance procedures to assure a proper groundwater barrier is constructed. The paper concludes with two brief case histories to illustrate how these considerations are applied

Jan 1, 2007

By Jesús E. Gómez

This work is a continuation of a paper presented in the 32nd DFI Annual Conference, Colorado 2007, titled ?Hollow Core Bar Micropiles - Design parameters interpreted from 260 load tests.? The first paper presented the results of the verification and proof tests performed for the retrofit of two bridges with hollow core bars that used 260 micropiles. It included an interpretation of the unit bond values in the different soils where micropiles were installed. Recently two additional bridges within the same geological environment were also retrofitted using 144 hollow core micropiles. This paper includes the interpretation of the additional data from the proof tests performed and refines recommended values for design of hollow core bar micropiles in soils similar to those encountered in these two projects. The authors believe that the data collected will significantly add to the relatively small existing database on micropile tests and may also be useful during implementation of the LRFD design methodology.

Jan 1, 2008

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

By Jørn H. Thomsen

This paper presents the experience gained and the lessons learned over the last decade within the numerous offshore foundation projects undertaken in the offshore waters of Denmark and Belgium by COWI A/S of Denmark. This experience derives from the close collaboration with, and interaction between the owners, contractors, and engineers in the various stages of project development. In turn, the experience draws on COWI's experience within foundation of large bridges world wide over half a century. Focus is on two pioneering gravity base foundation projects: ? Nysted in Denmark, currently the largest offshore windfarm worldwide with 72 Nos Bonus 2.3 MW turbines in water depths up to 10 m in the relatively benign inner Danish waters ? Thornton Bank in Belgium, where the first phase - comprising 6 Nos REpower 5MW-turbines of a total of 60 - are planned to be built in the rough North Sea in water depths exceeding 25 m.

Jan 1, 2013

By Zhang Baoshan

In this paper, the forced features and dynamic behaviors of stone-column composite foundation are concisely related. The characteristics of Rayleigh wave method is summarised. This method is proposed in which, the stress ratio of the stone-column to the surrounding soil and the bear­ing capacity of the composite foundation are determined. Through the engineering cases, it is shown that, checking and evaluating the composite foundation in this method, is feasible, with high speed and low cost.

Jan 1, 1991

By Abdul Aziz Hanifah

A novel instrumentation and analysis technique, called GLOSTREXT method has recently been introduced for bored pile load tests in Malaysia. This technique provides an innovative and improved alternative for conventional bored pile instrumentation methods commonly practiced for the past few decades. Results for five case histories involving full scale static load tests for high capacity bored piles with both new and conventional instrumentation details placed in within the same instrumented piles are presented to demonstrate the advantages of this novel technique. Results show good agreement between the new and conventional instrumentation.

Jan 1, 2006

Since the 1989 Loma Prieta Earthquake in the San Francisco Bay Area, the California Department of Transportation (CALTRANS) has accelerated seismic upgrading of their bridges. Many structures can be improved with the simple addition of hinge seat restrainers. Others require modification of column bents and superstructure to column connections. Often, footing retrofits are necessary, which require the addition of tension/compression elements (compression piling and tiedowns anchors) to resist overturning moments substantially larger than those originally used for footing design. These footing retrofits may include doweled reinforced concrete footing extensions or new pile caps which transmit forces to either driven steel or drilled concrete piles. In some cases, installation of these traditional piling elements is expensive, impractical or impossible due to: low overhead clearance, ground obstructions, high water table, noise or vibration sensitivity, or the inability to laterally expand the existing plan dimensions of the footing. In the latter case, one practical option is to attach small diameter drilled and grouted tension/compression piling elements (Pin Piles) to the existing footing. The footing may be strengthened with dowels and added concrete thickness or there may be a reduced shear span due to the installation of larger or jacketed columns. A reduction of elements is available with a Pin Pile alternative, particularly when the selection of traditional standard piles is governed by the reduced tension/uplift capacity available from the traditional elements, since Pin Piles exhibit superior uplift performance.

Jan 1, 1993

[ ]

Jan 1, 1994

By Takashi Saito

Since early 1970?s skirt suction foundations (skirted foundation / bucket foundation) have been used as support for large fixed substructures or anchors for floating structures in offshore hydrocarbon development projects. In recent years skirt suction foundations are recognized as one of the solutions in foundations applicable to bridge substructures installed in waters, because skirt foundations have a wide variety of functions such as control of settlement during service life, less impact to environments during operation at installation site. This paper introduces general features of skirt suction foundations, and then discusses design practice of them for the application to bridge substructures, with reference to experiments in both laboratory and field.

Jan 1, 2013

By William J. Neely

Augercast piles are formed by drilling a continuous-flight auger into the ground and, on reaching the required depth, sand-cement grout or concrete is pumped down the hollow stem as the auger is withdrawn. The sides of the hole are supported at all times by the soil-filled auger, eliminating the need for temporary casing or bentonite slurry. The augercast piling method is fast and economical; there is no vibration, very little noise and, if executed properly, no ground displacements during installation. The method is well suited to sands which are easy to drill and are readily transported up the auger. Relatively little attention has been given to augercast piles in the literature which might be part of the reason for the considerable variations in local practice, building code requirements and design methods. The purpose of this paper is to discuss some of the features of augercast pile installation that are known to influence both the structural and geotechnical capacity of the pile, to evaluate several empirical design methods and to look at some important aspects of quality control of augercast pile installation.

Jan 1, 1990

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010

By Jim Steding

L.G. Barcus and Sons, Inc. recently completed a three-phase project for the expansion of Presbyterian Hospital in Albuquerque, New Mexico for McCarthy Construction Co., the Construction Manager for the project. It was a challenge that allowed Barcus to demonstrate many of it's strengths. Safety of people and property, restricted access, low headroom conditions, extensive planning to maintain hospital operations and a tight schedule were all key elements affecting the successful installation of the Augered Cast-In-Place Piles. Phase I began with installing and performing a 450-ton pile load test on an 18-inch diameter Augerpile 65 ft long. The load test was installed and performed directly in front of the Emergency Room entrance. Space was limited and the E.R. had to remain open with uninterrupted ambulance access. The results of the load test were outstanding. In fact the test pile performed so well that some of the job piles were shortened from 75 ft long to 65 ft long. [ ]

Jan 1, 2003

By Juan M. Antorena

A dynamic testing program was performed to evaluate installation procedures, assess capacity of 610-mm (24-inch) diameter open ended steel pipe to evaluate set-up and provide minimum pile tip elevation based on the dynamic testing results. The program was performed for a marine terminal project consisting of a 570-meter (1900-foot) long, overwater railroad trestle. The project location is Santa Marta, Colombia, South America. The subsurface profile generally consisted of 4m (12 ft.) of water and soft to hard silty clays. The piles were installed to an approximate tip elevation of -22 meters (MSL). Three piles were initially dynamically monitored during installation and then later monitored during restrike driving to evaluate pile drivability and bearing capacity including time related capacity increases due to soil "set-up". Knowledge of change in pile capacity with time after end of initial driving is important for design of pile foundations.

Jan 1, 1995