Search Documents

By J. W. M. Porritt, M. P. Brameld, R. H. McCorkell

"Soil-gas Rn was measured by two types of alpha-particle-track detectors, by emanometry and by counting alpha-activity on Rn-decay-product collectors. Soil samples were analyzed for V by fluorimetric and fission-track methods, their Rn-emanation by decay-product collectors and their total alpha activities with track detectors. The same uranium anomalies were revealed by each method. Fission-track analysis of leaves for V showed only random variations with sampling site, and the Rn emanation of trees and leaves removed from them was barely detectable . The agreement among the other methods is significant, total alpha and collector methods are simple, rapid and useful, and a combination of methods at a site would reveal disequilibrium in the U-decay series if present. Track-Rn measurements are highly reproducible and insensitive to apparatus design and their sensitivity is not enhanced by covering the detectors with thin foil or placing them in large containers.IntroductionIn the past two years , a number of methods of geochemical exploration for uranium have been tested by the authors over the known copper-uranium occurrence at South March, Ontario. This was done partly to compare methods and partly to develop and test new ones. The South march deposit has been described a number of times by others(1,2,3,4). The methods included in this study were the following.Emanometry, Radon in soil gas is measured by pumping the gas into the cell of a scintillation counter or emanometer(5,6). Alpha particles from radon (222Rn) and its decay products (218Po and 214Po) produce scintillations of light in the silver-activated zinc sunphide (ZnS(Ag) covering the walls of the cell. These are counted by a photomultiplier tube and scaler, the count ra sulphide (ZnS(Ag) covering the walls of the cell. These are counted by a photomultiplier tube and scaler, the count rate being proportional to the concentration of radon in the soil gas."

Jan 1, 1981

By F. J. Macias, A. Bruland, F. E. Dahl

"Tunnelling by use of Tunnel Boring Machine (TBM) is gaining a greater presence as a suitable excavation method. Disc cutter consumption has a strong influence on performance and cost when using TBMs and the influence becomes even more relevant in hard rock. Furthermore, good predictions of TBM performance and cost facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory assessments are needed. A new abrasivity test method called Rolling Indentation Abrasion Test was developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than traditionally used methods by introducing wear by rolling contact on intact rock samples. INTRODUCTIONHigh investments are involved in the tunnelling industry, especially in Tunnel Boring Machines (TBMs) projects. Performance predictions and cost estimations are crucial for planning and risk management of TBM projects. Cutter consumption has a large influence in terms of time and cost, and an even greater effect in case of hard rock projects. Many factors are influencing the amount of cutters consumed in hard rock TBMs. Normal TBM operation results mainly in abrasive wear on the cutters and appropriate methods for abrasivity assessment are needed. Rock abrasiveness cannot be considered as an intrinsic property and the complete tribological system should be considered in addition to the geological properties of the rock.In the present paper, a new test method for abrasivity assessment in tunnel boring called Rolling Indentation Abrasion Test (RIAT) is presented. The traditionally used test methods for determination of rock abrasiveness uses sliding or impact contact in order to cause wear while the RIAT introduces rolling contact on intact rock samples. The ambition of the new test device is to have a reliable method to evaluate the cutter wear in hard rock tunnel boring by reproducing wear behaviour on rolling disc cutters in a more realistic way. It has been established by many authors that the abrasion of a cutter ring is proportional to its rolling distance (Rostami, 1997; Bruland, 1998). In the present work, the weight loss of a mini-cutter ring is measured subsequent to testing in order to evaluate wear in the rolling process and could hence be related to cutter ring wear. Indentation of the tools in the intact rock sample is considered as an indication of the surface hardness of the rock or the resistance to indentation by rolling."

Jan 1, 2015

By Friedrich Benthaus

"The natural and man-made realities on either side of the Atlantic are different. Therefore, a large part of the other side' s knowledge and experience cannot be transferred easily. In the following, the author will attempt to describe some of those developments in the German hard coal industry which may be of particular interest to readers on this side of the Atlantic.The area of the Federal Republic is quite small, especially if compared with a country as large as Canada. On a territory the size of the maritime provinces of New Brunswick and Nova Scotia, Germany holds coal reserves roughly corresponding to the total Canadian reserves. More than 20 billion tons of hard coal down to a depth of 1500 m, and more than 30 billion ton s of brown coal of lignite are technically and economically extractable acording to current technology.However, not only are Germany's coal resources more concentrated; the country is also densely populated, and there are dense networks of railroads and highways All components of the so-called infra-structure are available everywhere, be it electricity, any machinery or personnel. Public opinion is likely in favour of an increased utilization of coal.The coal industry is well developed through a long evolution covering centuries. As a consequence, there is an effective and intensive cooperation of numerous bodies and institutions concerned with coal mining, from government agencies including the inspectorate to suppliers, trade union s, producing companies, to jointly operated management and research organizations. In the Federal Republic, hard coal is mined in deep mines only, and lignite in general, only from open-cast pits. There is a complete organizational and geographic separation of hard and brown coal in Germany. Because the Federal Republic holds only insignificant mineral oil and very little natural gas deposits, coal is essentially the only and consequently the most valuable source of energy."

Jan 1, 1984

By Stephan Day

Comments on Robust M3 to Protect Water Quality ?Regulatory and philosophical thinking have tended to evolve at decade scale since 1970s. ?Mines typically last more than a decade. ?Robustness is defined by the ability to adapt to new realities. Managing Water Quality in BC ?1973 ?BC Pollution Control Objectives ?1977 ?Federal Metal Mine Liquid Effluent Regulation (Fisheries Act) ?Late 1980s ?Philosophy of ?Designing for Closure? ?1990s ?Designing for Acid Rock Drainage Management ?2000s ?Awareness of need for water quality management in general, regardless of acidity

May 1, 2010

By Ted Nuorivaara

The use of polymer-surfactant mixtures as foam stabilization agents is a topic that has drawn the attention of several fields but has so far not be thoroughly studied in the context of mineral froth flotation. The present work showcases a study on the impact on flotation performance of cellulose surfactant derivatives and their mixtures with commercial frothers. Bubble size and foam property measurements were run in a two-phase system along with laboratory-scale flotation experiments conducted using a porphyry copper ore from a mine in Finland. A comparative analysis on recovery, grade and flotation kinetics is presented on the products obtained using: i) a partially hydroxylated cellulose derivative (i.e. hydroxypropyl methyl cellulose; HPMC), ii) a commercial polyglycol-ester frother (Nasfroth240; NF240), and iii) mixtures of these two. The results show that using frothers with a total concentration of 30 ppm, the HPMC-NF240 mixtures provide advantages in terms of Cu recovery, (i.e., up to 95%), compared to the use of either NF240 (ca. 76%) or HPMC alone (ca. 1%). Interestingly, only a small proportion of HPMC mixed with NF240 was sufficient to produce a measurable increase in recovery. This improved performance was attributed to a synergistic effect of the polymer-surfactant mixture which further reduced the bubble sizes in a two-phase system compared to that of NF240. The present work offers a further step into understanding the phenomena taking place when a short chained surfactant is either substituted or mixed with a cellulose derivative, offering potential ways of exploiting this behavior for the enrichment of minerals. INTRODUCTION Froth flotation has been the predominant technology used to beneficiate sulfidic copper minerals such as chalcopyrite ever since it was invented in the late 19th century. The reason for the domination of flotation technology lies behind its versatility in selective separation as well as relatively cheap operational costs (Wills & Finch 2015). Even though flotation of sulfidic copper minerals is moderately well understood based on the broad research work done around the subject (e.g., Albijanic et al., 2015, Bournival et al., 2017, Wang et al., 2015, Mikhlin et al., 2015, to cite only a few), the modern era presents new challenges to the primary raw material industry, including questions regarding sustainability of mining operations accompanied by a need to improve the process efficiencies due to declining ore grades (Edraki et al., 2014).

Jan 1, 2019

By Paul M. Lévesque

The Dome Mine has been in production for nearly 100 years and throughout the years many different mining methods were used to extract the ore. An exploration program late in the 1990s outlines new resources requiring the mine to extract the rock and some previously placed backfill (alluvial sand and/or classified tailings). It is therefore imperative to separate the backfill from the rock to reduce the negative impacts of handling the backfill on the ore pass, crushers and mill processes. Separating the backfill from the ore at the source would also reduce and/or eliminate the cost of handling this waste stream. The paper will touch on the backfill removal criteria, the risks, the alternatives and the selected method, screen decks, for backfill removal at the Dome Mine. The 155549 bulk zone case study will illustrate how the screen decks are in use at the mine. The paper will also illustrate how the lessons learned and conclusions of the work done for the 155549 bulk zone were applied to the second screen deck installation for the 257260 bulk zone.

May 1, 2009

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By T. H. Patching, M. W. Mikhail

"The gas sorption and emission characteristic of coals are important to the planning and conduct of mining operations. Methane drainage from coal strata can also provide a supply of fuel in certain circumstances. Gas emissions have also created hazards during the handling and transport of coals and the release of gas also appears to be related to the yield of fine sizes during mining and processing operations.This paper summarizes studies at the University of Alberta on the permeability and gas emission of certain bituminous coals. Permeability of 'solid' samples was found to be drastically reduced by confining pressure. An emission index, .P, which has been related to outbursting behaviour of coals, has also been related to the proportion of fine s in cleaning plants. Gas sorption isotherms are dependent on temperature, moisture content, the gas involved and the type of coal and can be approximately expressed by the Langmuir or the Freundlich equations. Sorption values in sections taken across a given seam were similar but considerable differences were found in . P indices in the different coal layers of a seam.IntroductionThe emission of gases, especially of methane, from coal has been a subject of great interest (and sometimes a matter of life and death), to those who dig and handle coal since it was first mined from underground pit s. Many studies and investigations have been carried out on gas occurrences and emissions but our knowledge of the precise mechanisms of gas sorption, desorption and flow from coal is still incomplete. It is the purpose of this paper to review the principal factors involved in these processes and to briefly rep ort some of the results that have been obtained by studies in the laboratories of the Department of Mineral Engineering, University of Alberta, and Coal Research Laboratory, Edmonton, CANMET"

Jan 1, 1986

By R. C. Lo, M. D. Scott

"This paper reviews tailings management at Highland Valley Copper, and outlines main features of its tailings storage facility enclosed between the H-H and L-L dams. Key management focusses are: energy efficiency, cost effectiveness, safety and integrity of the tailings impoundment, environmental protection, and reclamation after decommissioning. Main features of the tailings facility include: high international standards for seismic and flood design criteria, water management and water quality monitoring, operations and construction optimization, reclamation and decommissioning plan, and geotechnical challenges associated with the complex geology of the L-L tailings dam foundation.IntroductionHighland Valley Copper stores its tailings mainly in the Highland Valley tailings facility (ultimate capacity: 1.8 billion tonnes). Smaller tailings storage facilities were operated by predecessor companies: the Number One Pond, the Trojan Pond at Bethlehem and the Highmont Pond at the Highmont operation as well as backfilling the Heustis and Jersey lona Pits at Bethlehem. These areas are currently not in use, and are in the reclamation phase prior to decommissioning. This paper focusses on tailings management in the main facility. As indicated in Figure I, the facility includes three tailings dams: these are, going from east to west, the H-H, J-J and L-L Dam, named after the alignment alternatives in the initial feasibility studies. From 1970 to 1977 Canadian Bechtel Ltd. advised Highland Valley Copper's predecessor company Lornex, on tailings storage at the H-H and J-J Dams and on the L-L Dam. Since the completion of the L-L Starter Dam in 1977, Klohn Leonoff Ltd. has provided ongoing consultation and construction monitoring of the raising of the L-L and the H-H Dams. The J-J Dams is currently buried by deposited tailings. This paper reviews key tailings management focusses and main features of the tailings facility."

Jan 1, 1992

By K. R. Wood, G. W. McDonald

"The tailings disposal system at Les Mines Selbaie includes dewatering of tailings in a high-capacity thickener, followed by point discharge of the thickened solids to form a stable conical pile. Tailings water drains to ponds formed behind engineered dams, prior to either recycling f or process use or discharge to the environment. Design and economic considerations of the system are discussed. Construction, start-up and operating experiences are also presented.Introduction Les Mines Selbaie is located in the Abitibi region of northwestern Quebec, approximately 700 km north of Toronto and 150km south of James Bay. More locally, the Detour gold mine is 60 km to the west while the Noranda smelter is 220 km to the south.The deposit was discovered as a result of a Questor INPUT Mark VI geophysical survey in 1973, followed by diamond drill programs from 1974 to 1976. Three mineralized zones were delineated and underground exploration was carried out on all three. A production decision for the 'B-zone' copper-gold-silver orebody was made in July 1979. The underground operation started in July 1981, with full production of 1500 t/d being achieved in May 1982.During the planning phase, every effort was made to ensure that the operation would be environmentally sound . The design included the provisions of the then newly proposed provincial environmental guidelines. The tailings disposal system formed the most significant part of the environmental program due to the large volumes of solids and water effluent. In addition, the design allowed for future expansion of the system to accommodate mining of the other zones, thus minimizing future costs and disruptions."

Jan 1, 1986

By Zoltan Hajnal

Magnetic studies have been carried out on 88 surface and 157 underground samples from the Coronation Mine area of northern Saskatchewan. The intensity of the surface samples was compared to trace element determinations from the same locality. A good correlation was found between the titaniferous constituent of the rocks and the intensity of magnetization. From the direction of the remanent magnetism, two virtual geomagnetic poles were determined -latitude 12° 54' North, longitude 158" 17' West; and latitude 23" 42' North, longitude 163° 45' West. The sulphide ore specimens showed anisotropic susceptibility characteristics. A relationship was found between the measured maximum susceptibility values of the ore specimens and the direction of the tectonic forces which are considered to have formed the structure at the Coronation mine. Introduction T HIS paper summarizes the results of a study of the magnetic properties of samples from well-known Precambrian formations. The observed data give information for an interpretation of the magnetic field conditions in Precambrian times. The high magnetic intensity values indicate the importance of the study

Jan 1, 1965

By M. Walmsley, D. Maynard

"This paper describes the use of terrain and soil information in the planning of mine developments, particularly in satisfying many of the existing provincial regulatory requirements. It is also noted that, if properly used, this will provide a solid data base for cost-efficient and environmentally acceptable land use.IntroductionIn planning the development or expansion of a new or existing mine, engineering alternatives are judged on many factors, one of which is the environmental influence. Ecological investigations, ensuring consideration of a rational approach to managing land use and environmental impacts, should be carried out prior to a final decision being made on mine development. The Pit Slope Manual (CANMET, 1976) suggests that both baseline aquatic and terrestrial data be collected and interpreted in such pre-mining surveys. In British Columbia, planning procedures now exist which incorporate biophysical studies to help identify, assess and manage major environmental impacts associated with mine development.Methods outlined in the Guidelines for Coal Development (E.L.U.C., 1976) have been successfully applied in recent years. Following this example, the Inspection and Engineering Division of the B.C. Mineral Resources Branch prepared guidelines to help expedite the development of new base metal mines (Procedures for Obtaining Approval for Metal Mine Development; Ministry of Energy, Mines and PetroleumResources, 1979).The metal-mine guidelines require the proponent of a new mine development project to prepare a two-stage assessment proposal which systematically moves from a preliminary feasibility study (Stage I) to a final project design (Stage II), including application for regulatory approvals. One purpose of the Stage I report is to provide a description of the existing environmental conditions that could be affected by the proposed development. A preliminary environmental impact assessment should also be reported. The Stage II report will contain detailed assessment and management of environmental impacts."

Jan 1, 1981

By Andrew Cormier

"The Early YearsThe Grand Lake coal fields in New Brunswick undoubtedly can claim the distinction of being the first part of North America from which coal was mined and exported. The diaries of the Governor of Massachusetts during the first half of the 17th century clearly establish this fact. There is also a reference in the Massachusetts Colonial Records which indicate that coal exports to New England were carried on as early as 1639.It has generally been believed that Cape Breton mined and exported the first coal; but no account has yet been found to show that this took place earlier than 1676. Both at Grand Lake and Cape Breton the coal was near the surface and removed by hand.When the country passed entirely into British control, Joseph Garrison, a grantee of Maugerville in 1765 moved to Jemseg. While surveying the north side of Grand Lake he discovered outcroppings of coal on the shore of the lake and further inland along the banks of streams. It was he who named Newcastle Creek in reference to Newcastle in England, which was widely known for its coal mines. Joseph Garrison died in 1783, the same year that an influx of United Empire Loyalists increased settlement in Newcastle Creek in the area now known as Minto. Many Loyalists also settled on the shores on both sides of Grand Lake.At a number of points where streams cut channels through the overlying strata, the coal seams were exposed and it was at such outcroppings that the early operations were carried on. A tunnel was driven in the seam from the foot of the bank, affording both an outlet for the coal and natural drainage from the workings. The coal was loaded into boxes and wheeled over wooden tracks to a point on the surface where it could be dumped into wagons and hauled either direct to destination or to where it could be loaded into boats and conveyed via Grand Lake, Jemseg and Saint John river to points of distribution.In the latter part of the 18th century and first years of the 19th century, farmers were undisturbed by mining the coal found on their lands. This was soon to change and resulted in many years of contention between landowners and the Legislative Assembly.New Brunswick became a separate province from Nova Scotia in 1784 and the seat of government moved from Saint John to Fredericton in 1788. The new province had its first priorities; the establishment of counties, the building of roads, and the development of its natural resources. From 1805, records of coal and land development are fairly complete. These records show the increasing interest of the Province in developing the coal fields. This interest resulted in the granting of coal leases to many friends of the government, without any regard for the wishes of the farmers who owned and had occupied the land for many years. The farmers fought back with lawsuits and other forms of dissension but with little success. By the end of the 19th century there were very few farm operators left in the area."

Jan 1, 1992

By N. Kolev, M. Poibrenski, I. Nishkov

"The following paper examines the flotation of copper porphyry ores in Assarel concentrator with focus on the reasons for low molybdenum recovery in the final copper concentrate. The copper-porphyry ore of the Assarel deposit is characterized by its variable mineral composition and high clay content, which influence the process efficiency of their concentration. Particle size distribution, chemical and mineralogical analyses have been made on various flotation products showing the distribution of the main elements of interest - copper and molybdenum. It was found that molybdenum is not concentrated into the final copper concentrate as usual in the flotation of copper-molybdenum ores but into the tailings of the copper selective flotation (cleaner tailings). An attempt to explain these results has been made with proposals to improve molybdenum flotation. Low floatability of molybdenite is caused by the ultrafine clay minerals content in both the run-of-mine ore and copper flotation streams. In order to achieve selectivity of copper minerals against pyrite a significant amount of lime is used in the plant leading to higher pH conditions, which could be another possible explanation for the molybdenite depression. The results obtained after the laboratory experiments, showed that it is possible to restore molybdenite floatability using traditional reagents such as diesel, kerosene, etc., and introducing a new polymeric reagent as froth modifier.INTRODUCTIONOne of the main technical difficulties in the area of copper-molybdenum flotation is the selective recovery of both metals, especially the fine (<40 micron) mineral particles. The problem is even more serious when Cu-Mo ore treated contains a lot of natural fine particles, predominantly clays, micas and other gangue minerals. Peng and Zhao (2011) conclude that the mineral processing industry is well aware of the difficulty in treating ores in the presence of clay minerals. Tremolada et al (2010) found that clay minerals have been named as the main problem in ore beneficiation processes due to their small size, which cause a higher viscosity in grinding. In flotation, these clay minerals have natural hydrophobicity or float by entrainment.The impact of clay mineralogy on flotation performance has been reviewed in the literature and the various deleterious roles of clay minerals have been investigated (Bulatovic, Wyslouzil & Kant 1999; Jorjani et al, 2011; Farrokhpay, Bradshaw & Dunn, 2013). It is widely accepted that the actual flotation recovery problem appears to be caused by the properties of these fine particles: small mass (and/or momentum) – high interfacial free energy (Rubio et al., 2007; Farrokhpay, 2011). In most cases, the loss in recovery is found to be insignificant, but the detrimental effect on the concentrate grade is found to be more prominent. The main reasons for the flotation inefficiency are the low probability of bubble-particle collision and adhesion, formation of dense froths and as a result - low process kinetics. A great deal of fine valuable minerals is discarded as slime in flotation due to lack of effective recovery methods."

Jan 1, 2016

By Robert Lamarre

In today?s environment, the availability of production equipment is a must to increase throughput and profits. For a number of mining organizations around the world, spare parts availability is key to achieving this goal. Fortunately, having less production equipment immobilized by a lack of spare parts does not equate to increases in inventory levels or in carrying costs. Advance operations research has shown a number of avenues to increase equipment availability while reducing total investment in stock. The presentation will explore these avenues by focusing on key inventory management changes that can be implemented by organizations to optimize their service and stocking levels. We have successfully applied our approaches in start-up mining projects, in mature projects and in end of life mining operations. We will illustrate our methodology using examples from our work with > 30 mining sites around the world.

Aug 1, 2013

By Zygmunt Wegrzyk

Poland is rich in hard and brown coal reserves, which have become the most important, and steadily developing, primary source of energy. With 192.6 mill. t of hard coal production and 40 mill. t of exports in 1978, Poland is fourth and second in the world respectively. The paper discusses the various mining methods adopted in the country&apos;s history of mining. Particular emphasis is placed on longwails, their mechanization and equipment assembled in the form of fully mechanized face complexes suited for varied geological conditions. Measures to improve the recovery ratio of coal resources are dealt with. investment efforts undertaken in the coal industry are outlined. An account is given of the ever improving techno-economic results of coal mining. The country also exports a wide range of mining equipment and transfers its well-founded technical know-how to others. There are strong cooperative links with many foreign partners.

Jan 1, 1979

By Stéphane Chevrel

Non-energy raw materials are vital inputs for the EU?s economy and maintaining fair and undistorted access to these materials for EU industry and citizens is increasingly difficult. Within the EU, exploration and extraction have to face increased competition for different land uses and a highly regulated environment. While the EU is currently dependent on the importation of many metals, the overall potential for mining and quarrying in Europe is strong. In spite of this, the land area available for extraction in the EU is constantly decreasing, turning access to land into a key challenge for the extractive industry. The EOMINERS project aims at contributing to demonstrate how to improve the EU capacity in implementing new mining sites and their societal and environmental acceptability. The overall aim of EO-MINERS (Earth Observation for Monitoring and Observing Environmental and Societal Impacts of Mineral Resources Exploration and Exploitation) is to bring into play EO-based methods and tools to facilitate and improve interaction between the mineral extractive industry and the society in view of its sustainable development while improving its societal acceptability. EO offers a unique opportunity to collect necessary spatial parameters that play a key role for better assessments of mining-related environmental and societal impacts. It could enable the development of means to identify the site-specific environmental and societal footprints of mineral resource extraction and to determine their respective significance. This understanding of global and cumulative footprints along a causal chain is needed in order to target policy measures. In this way the expected reduction of environmental and societal footprints in the mining sector can be most effective for the environment and more cost-efficient for public authorities and commercial operators. The project first defined environmental, socio-economic, societal, and sustainable development indicators and criteria that can possibly be dealt with using EO techniques. After an analysis of policies related to the environmental and social footprint of mineral industries, project expertise and stakeholder interviews (national and on-site) as well as site investigations led to the establishment of a list of indicators to be monitored, either directly or indirectly, through accessible parameters. Development of EO-based monitoring tools is then carried out over three demonstration sites: the lignite open pit of Sokolov in Czech Republic, the Mpumalanga coalfield centred on the town of Emalahleni (previously Witbank) in South Africa, and the Makmal gold mine in Kyrgyzstan. From these developments, it is subsequently intended to contribute to the development of generic, standardised EO data integration schemes, in particular in view of characterising affected ecosystems, populations, and societies and prepare indisputable documents that will make the basis for a sound ?trialogue? between industry, governmental organisations, and stakeholders. This paper discusses results obtained after three years into the project, focusing on product development over the demonstration sites and their relevance to the observation and monitoring of environmental and societal footprints of the extractive industry.

Aug 1, 2013

By G Anders

Underground tests of slusher cables at first might seem to be quite simple and inexpensive. They do, however, take a long time and give results that may be ambiguous and unreliable. Also, because underground test conditions are not exactly duplicable, tests carried out at different times or in different mines could not be compared. An attempt was made to develop a laboratory test method that would provide for all factors affecting slusher cable performance underground in such a way as to make it possible to achieve comparable results from different series of tests by exactly duplicating test conditions. Such a method should also make it possible to vary individual factors systematically in order to give a proper assessment of the effect of changing conditions on cable performance. A set of tests, comparing the same two types of cable both underground and in the laboratory, is described. AN assignment at the Algom Nordic mine called for the comparison of two types of %-in. slusher

Jan 1, 1964

By John A. Meech, Irene E. Cristoveanu

"The separation of hematite fines (100% - 38 um) from quartz fines (100% -75 um) was investigated using coarse hematite (-212 + 150 um) as a carrier in an oleic acid collector system. Oleic acid additions, per cent coarse additions, combined conditioning time and ferric chloride additions were examined.It was found that carrier flotation is a dominant mechanism for fine hematite recovery at oleic acid levels greater than 200 g/t and coarse additions of 10 per cent. Hetero-aggregation is favoured under conditions of lower levels of oleic acid in the presence of ferric chloride and at conditioning times greater than ten minutes.Ferric chloride acts as a depressant for pre-reagentized coarse hematite at oleic acid levels below 150 g/t. At concentration levels above 500 g/t, ferric chloride interferes significantly with the success of carrier flotation of fine hematite.The sensitivity of carrier flotation to changes in oleic acid addition, ratios of fine and coarse material, conditioning time and the presence of an inorganic electrolyte emphasizes that its application is only suitable when flotation conditions can be stabilized.IntroductionThe production of fine material is unavoidable during the comminution of iron ore . Due to the difficulty of recovering iron from this fine material by various gravity separation methods, flotation can often be a more attractive process producing high-grade material at high recovery. One variation of the flotation process, that can be useful for recovering ultra fine minerals (<10 um) , is known as carrier flotation. This process involves the utilizat ion of coarse particles ( > 150 p.m) which act as flocculation centres to which the fine hematite particles (10 - 40 u.m) become attached and are carried or "" piggy-backed"" into the froth phase."

Jan 1, 1985