Search Documents

By J. Zachwieja

As part of a general review on study of surfactant blinding agents to improve gold recovery during cyanide leaching of carbonaceous gold ores, processes of CIL and RIL leaching using surfactants were investigated. When refractory ores were treated by surfactants, CIL and RIL leaching processes yielded significant improvement on gold recovery. This paper will discuss and compare the laboratory results from two different leaching processes on preg-robbing ores, as well as, illustrate the difference of potential fouling of the blinding agents on activated carbon and resins.

Jan 1, 2015

By W. S. Szolga, M. Moser, M. D. Soderstrom, L. Cohen

"CYANEX® 272 is a phosphinic acid-based solvent extraction reagent used commercially since the early 80’s to recover and purify cobalt from sulfate solutions. Historically, the design of CYANEX 272 circuits has involved the selection of an optimal pH profile during pilot-scale testing using mixbox pH control. The desired pH profile is required to be carefully controlled in the same manner during commercial operation. To assist operators in the design and optimization of their circuits, Solvay developed CYANEX 272-specific solvent extraction modeling software, which has enabled determination of the ideal pH profile and staging configuration. Solvay’s recent advances in modeling capabilities have allowed the simulation of circuits without direct mixbox pH control. Modeling has indicated that circuits operated without direct pH control can achieve the desired metal separation while simplifying the commercial operation significantly. This paper reviews a number of potential circuit configurations for the use of CYANEX 272 and demonstrates the separations achievable under the right design and operational conditions, some of which have historically been considered too difficult.INTRODUCTION CYANEX® 272 is a phosphinic-acid based reagent designed specifically for the separation of cobalt from nickel by solvent extraction from weakly acidic sulfate solutions (Rickelton, Robertson, & Burley, 1982; Rickelton, Flett, & West, 1984; Rickelton & Nucciarone, 1997). Following commercial introduction in the 1980’s, CYANEX 272 has been used in a number of hydrometallurgical flowsheets for cobalt purification and/or recovery. CYANEX 272 metal extraction occurs by means of a cation exchange mechanism. Extraction of a divalent metal ion M2+ is represented by the following equation where RH represents the CYANEX 272 ligand and MR2 represents the ligand-metal complex."

Jan 1, 2017

By G. Granata, C. Tokoro, M. Matsuoka, K. Horiuchi

"Given the high demand of copper and the lack of new high-grade deposits, low grade copper ores containing copper oxides and refractory sulfides need to be processed as well. However, in order to recover copper from refractory copper ores, the leaching performances should be improved. In this study, we investigated the effect of the mechanical activation in the leaching of copper from covellite. The influence of a mechanical treatment by planetary ball milling on leaching rate in sulfuric leaching media was evaluated by using X-ray diffraction (XRD), mineral liberation analysis (MLA) and X-ray absorption fine structure (XAFS). Results showed a significant increase in copper leaching from around 50%up to 100% along with an improvement of the leaching kinetics when using planetary ball milling. XRD spectra showed the disappearance of the covellite peak from (101) face, thus suggesting the amorphization of covellite associated with the use of planetary ball milling. XAFS results showed that the coordination number of Cu changed from 6 to 3, thereby confirming the effectiveness of the mechanochemical effect.INTRODUCTIONDuring the last decades, while the copper grade in copper ores has been decreasing, the concentration of impurities such as arsenic tends to increase, thus requiring for the processing of low grade copper ores. For a suitable processing of copper minerals, hydrometallurgical processes are preferable due to the lower costs, the lower environmental impact and the easier implementation (Watling, 2006). However, for an economical recovery of copper, the leaching performances must be improved.Among the recent advancements in leaching technologies, the mechanochemical activation allows for an improvement of the leaching performances by means of high-intensity grinding(Mohammadabad et al., 2016). In the first place, the improvement is the result of the dramatic decrease of particle size, which results in an increase of the mineral surface area and the consequent enhancement of leaching kinetics. Furthermore, the intense mechanical stress due to the high-intensity grinding could induce the rupture of the crystal structure producing a decrease of crystallinity. Such changes of the mineralogical structure, also known as mechanochemical effect, can lead to more leachable mineral, thereby resulting in a greater dissolution of copper. Last but not least, whereas the mineral surface might undergo passivation during leaching, the high-intensity grinding can continuously refresh the surface of the mineral, thus exposing portions of unleached bulk mineral."

Jan 1, 2017

By L. Narhi, K. Haavanlammi

"Approximately two thirds of annual nickel production is used as a raw material in the making of stainless steel, and about 60% of these nickel products are in the form of metallic nickel such as nickel cathode or briquettes. In the stainless-steel production process nickel is blended with iron and chrome-based raw materials, and metallic nickel is typically only required for final steel fine-tuning. Outotec offers a new FeCrNi technology to enhance the nickel value chain for stainless steel producers. This involves the use of an HPAL-based intermediate nickel product (e.g., mixed hydroxides or NiO) as raw material in the Outotec FeCrNi process, for the production of a FeCrNi Master Alloy. The new process, designated as the FeCrNi process, offers multiple benefits compared to existing technologies such as: higher tolerance for impurities in the HPAL intermediate product, avoiding the need for further nickel refining, and the improved recovery of all metals in the FeCr process. The complete new FeCrNi value chain is based on proven technologies such as HPAL and the Outotec FeCr-process. This new innovative and promising value chain offers improved efficiencies for the HPAL based nickel production process combined with excellent sustainability aspects.INTRODUCTION In today’s global economy there is a constant need to improve the efficiency and sustainability of the metals production. The requirements for modern metal refining are tightening and cost efficient, safe and sustainable operation is the precondition for all investment. Outotec is offering now a novel way to combine FeCr and Nickel production to create a completely new value chain to source nickel to stainless steel. BACKGROUND Nickel The current nickel mine production is in the level of 2,000 tons annually and it is split 44% from sulphide based deposits and 56% from laterite deposits (Figure 1). Most (40%) of the nickel is refined to pure nickel metal whereas other products are FeNi (19%) and Nickel Pig Iron NPI (20%) (Roskill). The remaining part, roughly 21%, is nickel chemicals and intermediates. Most of the new investments in nickel are in the direct shipping of laterite to produce nickel pig iron. HPAL process is considered in few projects but no major HPAL projects have been started since the Ambatovy plant in Madagascar. Ambatovy reached the commercial production in 2014. The main primary nickel used is stainless steel manufacturing. In the year 2016 about 68% (~1,360 kt) of primary nickel production was used in stainless steel."

Jan 1, 2017

By Y. Tanaka, M. Maeda, S. Suzuki, C. Tokoro, T. Kato, K. Muto

Boron (B) co-precipitation was investigated with ettringite to establish a cost efficient method of removing B from acid mine drainage. For 25 mg/L of B solution, most appropriate pH for B removal was pH 11.5. The most appropriate amount of reagent for B removal within Japanese effluent standard (10 mg/L) was B:Al:Ca:SO4 = 1:3:9:4.5, which corresponds to the composition of Ettringite (Al:Ca:SO4 = 2:6:3). The effect of silicate, carbonate and temperature on efficiency of B removal is important as groundwater and hot spring water are often contaminated. When silicate and carbonate are present, more Al and Ca salts are needed for B removal since some aluminum and calcium precipitate with silicate and carbonate as kaolinite and calcium carbonate. These precipitates do not contribute much to B removal. As the temperature raised, the most appropriate pH for B removal decreased. B removal became less efficient as monosulfate precipitated more rapidly as ettringite.

Jan 1, 2015

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By Fazel G. Jahromi, Ahmad Ghahreman

"Several studies were performed on the atmospheric leaching of copper sulfide minerals in the presence of activated carbon and a new catalyst, AF 5. AF 5 is a carbon based catalyst with similar properties to those of activated carbon however much better mechanical properties. The activated carbon surface chemistry has been investigated in various studies; however the connection of the surface chemistry of activated carbon and AF 5 with the sulfide minerals during the atmospheric leaching process is not well-understood yet. Based on the surface analysis, AF 5 showed higher surface area than activated carbon (AC). Adsorption and oxidation of copper, arsenic and iron ions in the presence of different activated carbon were investigated. Adsorption properties of both catalysts were similar and 18-24% of iron, 12-18% of copper and 10% of arsenic adsorbed on the catalysts surface form 5 g/L Fe(III) and Cu(II) and 2 g/L As(III) at 80°C. In oxidation experiments, both catalysts reduced Fe(III) and Cu(II) ions and re-oxidized the reduced species in the presence of oxygen and oxidized As(III) ions. The addition of oxidizing ions can enhance the oxidation process kinetics and increase the catalytic capability of carbon.INTRODUCTION Hydrometallurgical processes of copper sulfide concentrates are under development and various different methods have been proposed to increase the atmospheric leaching rate of copper sulfide minerals. These methods include using different media, reagents, and catalysts. Among different methods, leaching of the copper sulfide minerals in the chloride media has some advantages over sulfate media. Smaller scale of operation, increased leaching rates, and lower sulfate formation are some of the benefits of the chloride leaching media over other similar media. Moreover, using ferric and cupric ions as oxidants and utilizing activated carbon as a catalyst has been proven to enhance the leaching rate of copper sulfide minerals effectively. Activated carbon (AC) and AF 5 (micro porous carbon based catalyst) are two of the most efficient and practical catalysts in copper sulfide leaching processes. AC can enhance the copper recovery of enargite in chloride media from 69% to 92% after 96 hours of leaching under the similar conditions (Jahromi & Ghahreman, 2016). It has been shown that AC at acidic pH can generate hydrogen peroxide in the presence of oxygen which can leach copper minerals (Ahmumada et al., 2002)."

Jan 1, 2017

By N. Ahern, L. Manoukian

"Cyanide is a leaching agent for precious metals commonly used in gold ore processing. Cyanide exists in various forms (including free, complexed as weak or strong complexes, and as ions such as cyanate and thiocyanate), so its detection, speciation and analysis in processing or environmental samples can be complex. This paper will review best practices for cyanide sampling and preservation in the field, interferences and pretreatment methods required prior to sample analysis and analytical methods that are used for cyanide species. Titrimetric, flow injection ligand exchange, spectrophotometric, colorimetric, potentiometric, amperometric, and chromatography techniques will be discussed and their chemistries, detection limits, advantages and limitations will be described.INTRODUCTION Cyanide is well known to be an extremely toxic species. Accurate cyanide measurement in effluent from mines is critical from an environmental perspective. Its measurement is also an important control parameter in the recovery of gold using cyanidation. Cyanide chemistry is diverse and complex, and cyanide analysis can be challenging as a result of and because of limitations in understanding of analytical methods. Various chemical mechanisms can form or destroy cyanide, and the sample matrix or preservation chemicals can also affect analytical results. These interferences make the collection of reliable cyanide measurements challenging and can start as soon as the sample is collected, during laboratory pre-treatment and during analysis. This paper reviews different methods of cyanide measurement. The basic chemistry of cyanide, best practices for sampling and preservation, as well as various methods of analysis will be discussed.CHEMISTRY The complexity of cyanide chemistry is well known (Beck, 1987; Delgado, Botz, Bucknam, Milasovljevic, & Staley, 2008; Botz, Milosavljevic, & Ward, 2013) and is attributed to the ability of cyanide to undergo: •,Volatilization •,Precipitation •,Adsorption •,Complexation with metals •,Oxidation to cyanate, ammonia, or cyanogen chloride •,Reaction with sulfur or sulfide minerals to form thiocyanate •,Redox reactions leading to the formation of cyanogen and cyanate •,Redox reactions (of some cyano complexes) •,Photochemical reactions (of some cyano complexes)"

Jan 1, 2017

By O. A. Ojo, N. Esmaeili

"The effects of brazing and use of composite powder mixture as interlayer material on hot corrosion resistance of brazed IN738 superalloy were studied. Brazing was observed to result in significant reduction in the hot corrosion resistance of the superalloy. However, application of composite powder mixture, which consists of additive superalloy powder, enhanced the hot corrosion resistance of brazed samples. It is also found that although the use of composite powder mixture increased hot corrosion resistance of brazed alloy, if the additive powder completely melts, which is possible during brazing, it can significantly reduce the hot corrosion resistance of the brazed joint. Elemental micro-segregation during solidification of the joint with completely melted powder mixture produces chromium depleted zones and consequently reduces hot corrosion resistance, since a uniform distribution and adequate chromium concentration is necessary to combat hot corrosion. This has not been previously reported in the literature and it is crucial to the use of composite powder mixture for enhancing the properties of brazed superalloys.INTRODUCTION Superalloys have been developed in response to the increasing demand for materials with higher resistance to corrosion and creep and also with higher mechanical strength at higher temperatures (Smith, 1981). Ni-base superalloys are predominantly used in manufacturing hot sections of gas turbine engine components. This is due to their high strength and corrosion resistance in extremely high temperature service environments which is typical for hot sections of gas turbine engines (Miglietti, 2009). The continuous demand for higher efficiency and output has resulted in the use of higher operating temperatures and gas pressure in modern gas turbine engines (Jahnke & Demny, 1983). Consequently, this has caused thermal and mechanical stresses which result in severe degradation and damage of gas turbine engine components due to creep, fatigue and hot corrosion (Zhang, Feng, & He, 2006). The decision to replace or repair damaged parts depends on the overall repair cost and expected life of the repaired components (Jahnke & Demny, 1983). However, in most cases, it is more cost effective to repair damaged parts rather than use a full replacement."

Jan 1, 2017

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Previous testwork by the authors has indicated that both granular coconut shell based activated carbon and a new microporous carbonaceous bead, Lewatit® AF 5, are highly effective in improving the oxidation kinetics and decreasing the elemental sulphur yield when assisting the atmospheric oxidation of pyrite. While the two carbon catalysts show similar results and improvements to the pyrite oxidation, there are differences between them. For example, the activated carbon assisted oxidation showed faster kinetics than the AF 5 assisted oxidation, while elemental sulphur seemed to remain adhered to the surface of the AF 5 after oxidation when much of the elemental sulphur formed during the activated carbon assisted tests was found in the oxidation residue. The objective of this paper is to investigate the differences between the two catalysts through the use of scanning electron microscopy, photography, Raman spectroscopy, surface chemistry analysis, and Brunauer-Emmett-Teller (BET) surface area analysis. With this investigation the authors should be able to achieve a better understanding of the surface chemistry of the two carbon catalysts (i.e. functional groups, charges, acidity etc.) and help explain the strengths and/or the weaknesses of the catalysts when applied to the atmospheric oxidation of pyrite.INTRODUCTION Previous research conducted by the authors, indicated that both a granular coconut shell based activated carbon (activated carbon) and a microporous carbonaceous bead, Lewatit® AF 5 (AF 5), acting as a catalyst enhanced atmospheric pyrite oxidation in ferric sulphate media by approximately 40% when compared to unassisted oxidation and that elemental sulphur yields were increased from 23% to approximately 69 and 63% when assisted by AF 5 and activated carbon respectively (Cowan, Jahromi, & Ghahreman, 2017). The study indicated that although total pyrite oxidation assisted by the two catalysts was similar, differences were noticed in the impact that the two catalysts had on the outcome of the oxidation. Kinetic curves in the Cowan et al. study indicated that atmospheric oxidation of pyrite seemed to reach completion after 48 hours of oxidation when assisted by activated carbon. A similar trend was noticed in the kinetic curves for oxidation when assisted by AF 5, however the oxidation curve did not reach completion until approximately 96 hours (Cowan et al., 2017). This observation indicated that the kinetics of pyrite oxidation are enhanced by both catalysts, oxidation kinetics are much faster when assisted by activated carbon rather than AF 5."

Jan 1, 2017

By Henrik Saxén, Mikko Helle

The operation of hot stoves used for preheating the blast in the ironmaking blast furnace has a strong effect on the consumption of reductants, economic performance of and CO2 emissions from the steelmaking site. Generally, it is recommended to maintain as high blast temperature as possible, because this minimizes the rate of reductants in the blast furnace. The blast temperature is affected in a complex way by the time periods of heating and cooling of the stoves, and by the amount of gas combusted in the stoves. Furthermore, as the hot stoves show degraded performance with age, it is a non-trivial task to select optimal operation parameters for the stoves. The paper addresses this computationally by applying a one-dimensional heat-transfer model of the hot stoves for optimization of the performance of the system. The complexity and strong coupling of the decision variables is demonstrated by numerical examples, where the blast temperature is maximized under different constraints.

Jan 1, 2015

By Fazel G. Jahromi, Ahmad Ghahreman

"Atmospheric leaching of arsenical sulfide concentrates, and especially enargite leaching, is one of the major challenges within the current hydrometallurgy research area. One of the recent processes developed for sulfide ore treatment is atmospheric leaching in the presence of AF 5, a novel carbon based catalyst, in chloride media. The quantification of different ion concentrations during enargite and chalcopyrite leaching in the presence of AF 5 were measured and the copper recovery rates of 97% and 96% were achieved. The objective of this study is to shed light on the leaching mechanism of the sulfide minerals. Based on the speciation of iron and copper by different titration methods, the AF 5 catalyst first reduced ferric and cupric ions and then oxidized ferrous, cuprous and arsenite ions. The oxidation behavior of the catalyst enhanced the leaching results. The AF 5 catalyst also caused in situ precipitation of scorodite in leaching experiment. The speciation of ions in the chloride media were simulated by Phreeqc software and the dominant species in the leaching solution were determined.INTRODUCTION The hydrometallurgy of copper has been used for several decades and is still under development for more complex copper sulfide minerals due to their refractory nature. Most of the world copper reserves are in the form of chalcopyrite; and enargite is known as a major contaminant. Pyrometallurgical processing of enargite is problematic due to arsenic release and tight environmental regulations (Peacey, Gupta, and Ford n.d.). On the other hand, lower recoveries in the hydrometallurgical processes make most of these processes impractical. Several leaching processes have been developed for the leaching of copper sulfide minerals. Some of the common treatment methods for copper sulfide minerals are pressure oxidation leaching (POX), CESL, Activox, Albion process, atmospheric ferric sulfate leaching, Dynatec, Galvanox, and Hydro copper process (Barr, Defreyne, and Mayhew 2005; Conner and Anderson 2013; D.G. Dixon, Mayne, and Baxter 2008; Hyvärinen and Hämäläinen 2005; Palmer and Johnson 2005; Rohner, Bartsch, and Ngoviky 2012). Generally it is not viable to dissolve copper sulfide minerals at ambient pressure in mild acidic media and dissolution of these refractory minerals requires harsh conditions in the presence of oxidant materials (Biswas and Davenport 2002). Ferric ions have been used as an oxidant in different media in copper sulfide leaching processes. U. S. Bureau of Mines’ Reno Metallurgy Research Center in 1969 (Haver and Wong 1971) investigated ferric chloride leaching of chalcopyrite. Dutrizac and Macdonald (1972) studied ferric sulfate leaching of enargite. Based on this study, 50% of the copper was recovered at 80-85 ºC after 7 days of leaching. Cupric ions can also be used as an oxidant. Parker, Paul, and Power (1981) stated that cupric/cuprous couples are more effective than ferric/ferrous couples in chloride media because they are rapid and reversible. The Hydro Copper process leaches copper sulfide minerals in chloride solution catalyzed by cupric ions. In this process, copper dissolves as cuprous ions in presence of cupric ions (about 10 g/L) (Hyvärinen and Hämäläinen 2005)."

Jan 1, 2017

By D. C. Crothers

"What is new in air compressors? A good deal - the designers have been keeping pace with technical developments in related fields and also contributing new techniques of their own. Plant reliability no longer requires bulky slow-speed machines. Even the reciprocating machines, which still provide the most efficient method of compressing air, have been greatly reduced in size and installation cost for a given capacity rating. New materials and fabrication techniques are being used, by most manufacturers, to produce less costly plants in total. Many packaged plants are available, which generally means a more complete assembly for shipment. This type of construction offers savings in handling and erection costs at the site. A warning is in order, however - the extent of packaging in any given plant should be investigated carefully to determine what is included and just what field costs can be realized. A suggested specification has been offered for consideration when studying comparative costs. Rotating machines intrigue many because of their potential as regard fewer wearing parts, higher speeds and hence smaller units, utilizing less expensive drivers, and lack of contamination of the compressed air by lubricants. The inherent shortcomings of these machines - lower •efficiency and capacity control - have been much improved lately, and this type of plant is now becoming quite popular. Noise control, of much concern to everyone, is another development that has received considerable attention.Systems for efficient capacity control and continuous monitoring of compressor operation offer additional reliability and low-cost operation of the modern compressed air plant. Accessory equipment and its effect on over-all plant operation is also considered."

Jan 1, 1972

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By Baochun Wang, Hongli Jia, Zhaolian Wang, Fengliang Liu

"Promote and apply a new beneficiation technology and equipment effectively processing the refractory and medium-fine grained weak-magnetic minerals. HUATE® Forced-oil Cooling Vertical Ring WHIMS adopts the transformer oil cooling technology to cool excitation coils, solving the easily generated scaling problem resulting from water cooling, thereby to eliminate the demineralized water system. With <25 temperature ?raise, its magnetic field is stable. Wrapped by outer magnetic armor, it can generate a background intensity 1360kA/m. It effects very well in 1) wet preseparating the weak-magnetic coarse grains, like hematite, manganese ore, ilmenite, and purifying the concentrate; 2) removing the ferrous impurities and purifying the non-metallic minerals, like quartz, feldspar, kaolin; 3) enriching and recovering tailings from non-ferrous metals, like copper, lead, cobalt, molybdenum, thereby to greatly improve the mine resource utilization. It has applied 14 relative patents in China, and the invention patent in 56 countries, like Russia, USA, Australia, via PCT international organization. HUATE® WHIMS has been applied and accepted in more than 100 mines in and out of China. Compared with water cooling vertical ring WHIMS, it’s energy-saving and water-saving, and avoiding generating the scale. While compared with JONES WHIMS under the same separation indexes, it’s featured of more space-effective, lighter, lower costs, higher gradient, higher efficiency, larger processing capacity and wider grain application scope. Greatly promoting development of mineral processing technologies, HUATE® WHIMS is the equipment to reduce costs and improve efficiency urgently needed by the mine enterprises now.INTRODUCTIONAt present, influenced by the price and production factors, the international market demand for the grade of iron ores is increasing continuously. Restricted by the ore occurrence state, the beneficiation technology level and product economic value, every year the stope strips the stockpiling and discards hundreds of millions of tons of waste rocks containing iron, especially the weak magnetic hematite and limonite with <20% Fe%. The utilization technological bottleneck of these waste rocks makes their concentration ratio as high as 5-6, which leads to the huge wastes of energy, materials and beneficiation reagents and the increase of production costs. The effective solution is to improve the selected Fe% of the waste rocks like hematite. With the successful application of HPGR technologies in Chinese large iron mines, the mill feeding size has been reduced to 6-0 mm or 3-0 mm from the original 15-0 mm in the crushing system with 3 stages of crushing and 1 stage of closed circuit. This creates the conditions for the wet separation and recovery. While for the medium-fine grained weak-magnetic minerals, it lacks of the effective separation and recovery equipment in the world, which’s badly in need of R&D of the medium-fine grained high gradient wet strong magnetic preseparation equipment."

Jan 1, 2016

By S. M. Chentouf, M. Jahazi, N. Bombardier, T. Belhadj

The main limiting factor in the commercial expansion of superplastic forming (SPF) of thin sheet aluminum alloys is the extent of cavitation phenomenon that takes place during the processing. The severity of the cavitation process is mainly dependent on the uniformity of deformation (i.e. level of local thinning) during processing. In the present paper, correlations are made between thickness variations in several formed sheets and the characteristics of the cavities observed in the material. The 1.4 mm thick 5083 aluminum alloy sheets were hot pre-formed at around 450°C for 4 min and then air-cooled. Opto-digital and Scanning Electron Microscopy were used to examine the microstructure and analyse the cavities. Also, grain size measurements were carried out for different location in the SPF formed piece. The surface and volume fractions of the cavities were measured with the aid of metallography image processing (MIPTM) on as-polished samples prior to etching. The results are analyzed in terms of the influence of applied strain and microstructure conditions on the propensity to cavitation of the alloy.

Jan 1, 2015

By Haruka Takeura, Tomoaki Murata, Kazunari Yoshida, Masato Adachi

"Pure magnesium is a material with high functionality, however, the cold drawing of this material is very difficult, that is why, until this day there are no optimal cold drawing conditions. Furthermore, cold drawing of pure magnesium wire shows a problem with internal defects that occurs under certain conditions. In this research, the aim is the suppression of internal defects, and final target is to create the optimal cold drawing conditions for pure magnesium wires. The first step is the investigation of the drawing limit by using 250°Cannealed wire. As a result, reduction of 10% per pass was chosen for stable wire drawing. However, in this case, it was found that internal defects occurred at total reduction of over 45% during drawing. Investigation of intermediate annealing conditions that can suppress internal defects, and influence on internal defect that the die half angle and reduction per pass. As a result, it was found that the drawing condition capable of suppressing internal defects most efficiently was 13% reduction drawing by using under 6°half angle die. Consequently, it’s possible to manufacture a cold fine drawn pure magnesium wire of 100µm, without defects in the center of the wire and hindering its mechanical properties.INTRODUCTIONMagnesium is a light and high functionality material that has high vibration absorbency, heat dissipation, electromagnetic wave-shielding and recycling efficiency (Conruy, 1989). However, proper cold wire drawing conditions haven’t been established, that is why warm or hot processing is commonly used (Oishi, Mori, &Kawabe, 2005). As a result, strength improvement of the wires is not possible, that is why the production of medical tools is disregarded. If it was possible to cold draw magnesium wires, the applications for material products would expand. Further, in wire drawing such difficult processing material, if appropriate processing conditions are not selected, defects will be generated inside the drawn wire."

Jan 1, 2017

By D. F. Zhang, X. Q. Jiang, N. Tahreen, D. L. Chen, F. S. Pan, D. Y. Li

Alloying with rare-earth elements has been proven to be an important tool for magnesium to achieve superior properties via texture randomization. The role of yttrium in texture weakening and the link between texture and formability are fairly well known. Since annealing is a vital part of metal processing which could significantly contribute to ductility, it is important to ascertain the impact of annealing in terms of texture change. Also, an understanding about texture development during pre- and post-deformation annealing is essential to improve the industrial deformation processing as texture is closely related to formability. While there is independent information in the literature regarding the effect of rare-earth addition and heat treatment on the texture formation, no systematic studies have been reported on the collective impact of yttrium addition, annealing and deformation on texture evolution. The present study was, therefore, aimed to identify the inter-relationship among texture evolution, yttrium content, heat treatment and deformation behavior in an extruded Mg-Zn-Mn-Y alloy. Annealing at 450°C for 1 hour and uniaxial compression tests at a certain amount of deformation were performed. The deformed and annealed samples were then subjected to annealing and compression test, respectively, followed by texture measurements. It was observed that yttrium addition effectively weakened the crystallographic texture in all conditions, which was evident from the changes in the microstructures and textures.

Jan 1, 2015

By Quenton Johnson, W. A. Gough, David Carr

"This paper describes the application of the BrainWave Model Predictive Controller (MPC) and Advanced Control Expert (ACE) Advanced Supervisory Control System on the SAG Mill, Ball Mill, and Rougher Flotation cells for a new gold processing line at the Oceana Gold - Haile Gold mine in Kershaw, South Carolina. For this project, ANDRITZ supplied the control system design and programming, operator-training simulator and advanced control. The advanced control was tested against the IDEAS™ dynamic simulator, and commissioned during the startup of the processing plant to help achieve target production as quickly as possible. Operators were able to run the equipment in a consistent and optimized manner from an early stage of the plant operation, increasing efficiency and profitability. MPC is able to reduce process variability beyond the best performance that can be obtained with conventional Proportional Integral Derivative (PID) control methods. MPC is able to optimize the control of processes that exhibit an integrating type response in combination with transport delays or variable interaction, which are characteristic of many gold processes including SAG mill weight control and Flotation cell froth level control. The experience and benefits of applying MPC during the startup of a new gold processing plant are presented in this paper.INTRODUCTION Mineral processing operations present many challenges for automatic process control due to variations in unmeasured ore properties, material transport delays, and non-linear response characteristics. Advanced process control technologies such as expert systems and multi-variable model predictive controllers are often used to improve the control of these processes to increase productivity and recovery efficiency. Typically these systems are applied after the mine has been in operation for a period of time. For this project, a complete dynamic process simulator was developed using the IDEAS platform for the purpose of training operators before the plant was constructed. Operators were able to become familiar with the process and the control system in order to become proficient in the use of the controls before the plant was ready to start. They were able to practice abnormal condition management including startup and shutdown of the process using the simulator and develop complete Standard Operating Procedures (SOPs) for these situations. The simulator was also used to test the control system functionality and operator Human Machine Interface (HMI) configuration to reduce errors and improve the performance of the control system during plant start-up."

Jan 1, 2017

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015