Search Documents

By O. J. Restrepo-Baena, L. Rojas-Mendoza

Gold losses must be controlled during extracting processes, especially during cyanidation. Otherwise recovery decreases and therefore the profitability of projects too. One of the phenomena that generate such losses is known as preg-robbing which occurs when some mineral constituent adsorbs aurocyanide complex from a cyanide solution. There are some laboratory methods to identify potential preg-robbing in gold ores, highlighting the PRP method, the BGMI test, and cyanidation tests by conventional agitation without activated carbon (BRP) and with activated carbon (CIL). For this study we performed an initial characterization of a sample from Antioquia - Colombia and then we carried out the methods described above in order to identify the presence of carbonaceous matter. We obtained a percentage of preg-robbing of 78.7% by applying the BGMI test; the preg-robbing potential by the PRP method was 97.9% with an extraction of 0.77% and an inferred recovery of 36.6% if preg-robbing did not occur. Finally we obtained under the BRT test a recovery of 0%, while for CIL test an extraction of 33.6% what confirmed the presence of preg-robbers agents in the gold ore. We conducted all tests in the Institute of Minerals - CIMEX at Universidad Nacional de Colombia - Medellin.

Jan 1, 2014

By Gordon L. Kidd

The object of this paper is to show the relations of the East Coulee coal area to the near-by Willow Creek, Wayne, Rosedale, and Drumheller areas, all being parts of the Drumheller field. The word ?area? is here used in a more local sense than that employed by Dr. J. A. Allan, whose. 'area' is rather comparable with the 'mining division' in British Columbia. I have drawn freely from the published information, particularly from Dr. Allan's report on the "Geology of Drumheller Coat Field, Alberta", and from Dr. E. Stansfield's paper on " A Chemical Survey of Alberta Coals", to whom thanks are due. The Drumheller field is served by branch lines of the two principal Canadian railways. The C.N.R. traverses the district by its Goose Lake line from Calgary to Saskatoon; and the C.P.R. by a line from Calgary to Acme and then southeasterly to Drumheller, where it effects a junction with the C.N.R., over which the C.P.R. has running rights as far as Rosedale. From Rosedale, a joint line built during the summer of 1928 extends about forty miles down the Red Deer river to the mouth of Bull Pond creek. From that point the C.P .R. turns more southerly to connect with the Bassano-Empress line. The C.N.R., it is expected, will eventually proceed eastward to connect with a transcontinental line. The joint line from Rosedale down the Red Deer river opened up the Willow Creek and East Coulee areas.

Jan 1, 1929

By K. J. G Hedges

"Once a health based guidance limits for exposure to diesel exhaust have been established, and as part of a multi-disciplinary team, the program for exposure reduction should incorporate the plan-do-check-adjust cycle. Setting a suitably protective (health based) occupational exposure limit (OEL) for diesel particulate matter (DPM) and nitrogen dioxide is a key driver to reduce exposure. It is important to go beyond regulations and reduce exposure to diesel exhaust, DPM, as low as reasonably achievable (ALARA) such as that prescribed under the Australia, Queensland Mining and Quarrying Safety and Health Regulation 2017 where under section 135 Limiting workers exposure, the workers exposure must not exceed the exposure limit applying to the worker for the hazard; and is ALARA. It appears that previously acceptable OELs are no longer safe. Therefore it is important that the internal responsibility system be implemented and the precautionary principle approach be followed, especially as it may be some time before a suitably protective OEL specifically for DPM is in place. One leading multi-national mining company BHP Billiton has acknowledged a significant lag that exists between regulatory action and the level of science that informs health risk. This company is managing exposure to diesel exhaust to as low as technically feasible. This same company that has set an interim target for managing diesel exhaust to 0.03 mg/m3 is achieving these levels which paves the way for other mining companies and general industry including construction. The Occupational Cancer Research Centre 2017 recommends reducing personal exposure to within 0.02 mg/m3 (EC) for underground mining and 0.005 mg/m3 for other workplaces. Controlling DPM is important to prevent cancer however it is also important that that nitrogen dioxide (NO2) be reduced (ALARA) and that careful selection of control technology be considered such as the proper selection of a diesel oxidation catalyst so that the level of NO2 does not in fact increase. The example from BHP Billiton provides a leading practice including using a multi-disciplinary approach and the importance of controlling emission at source and having an auditable diesel emissions based monitoring program in place."

Jan 1, 2019

By P. J. Urso

"The coal reserves of the Crow's Nest Basin in British Columbia have been known since the late 1860's. The 51.0-million-long-ton (over 15 years) sale of low-volatile coking coal to Japanese steel mills, as finalized in 1968, establishes the importance of these coal reserves in the world markets.In the early stages of the exploration program, which began in January, 1967, emphasis was placed on deter-mining the reserve of underground low-pitch coal within the No. 10 or Balmer seam of the Kootenay coal forma-tion. The finding of low-cover reserves in excess of 100,000,000 tons altered the initially planned underground program. Extensive tests were performed, establishing the excellent coking characteristics of the open-cast Balmer coal. Due recognition was given to the ultimate reclamation costs of mined lands and associated spoil areas.t was determined that, to achieve the costs desired, a high productivity was necessary, requiring large mining equipment. Operating criteria were set out, based on producing 4.2 million tons of clean coal per year. To optimize recovery, the preparation plant feed size was fixed at Yi in. x 0. The initial basic design capacity of the plant was 1,000 tph. The washing plant is composed essentially of four separate cleaning sections: a dedusting section; a multi-stage heavy media cyclone section; water cyclones; and flotation cells. Subsequent to the basic program, additional sales were made of 6.0 million long tons over the initial three-year period and the plant capacity was raised to 1,400 tph through the addition of a 400-tph coarse-coal treatment section. All wet coal products from the fine coal plant will be dried in a 70-tph (water) heat dryer. A unit-train concept of coal transportation between the mine site and the Westward Terminals at Roberts Bank has been negotiated with the Canadian Pacific Railroad. Facilities at the port will include a 4,000-tph rotary car bumper, 400,000-ton clean-coal stockpiles, and a bucket reclaiming system having a total ship-loading capacity of 6,000 tph."

Jan 1, 1969

By Guocheng Pan

"Although many factors play roles in the estimation of recoverable reserves, smoothing effect and conditional bias are considered major geostatistical issues in the estimation. This paper introduces measures for smoothing effect and conditional bias, and provides insights into their relation to the estimation of recoverable reserves. Both smoothing effect and conditional bias are intrinsic to the information effect and kriging estimators. For a given level of drilling information, however, it is possible to identify the optimal search radius that minimizes conditional bias. Furthermore, it is also feasible to define variance correction factor for reduction of the smoothing effect from exploration block models. Both of these components are key to the accurate estimation of recoverable reserves. IntroductionThe accurate estimation of recoverable reserves is critical to decision making in different phases of feasibility study and mine planning. Much attention for improving the methodology of estimation has been focussed on the effect of the change-of-support (Parker, 1980; Dagdelen, 1996). For example, it is essential to make a volume- variance correction to the estimate of multiple indicator kriging (Hoerger, 1992). When the size of block, b, in the geostatistical model differs from that of selective mining unit (SMU), v, a volume-variance correction is warranted for the prediction of recoverable reserves.Most mining plans and decisions are made prior to the availability of high density blast-hole samples. In most mining operations, the true SMU grade Zv is unknown at the time of selection. Instead, the selection is based on the estimate Z v**derived from high density blast-hole samples within the deposit G. Nevertheless, the estimate Z v * of recoverable reserves in the stage of mine planning is derived from exploration data. At the end, the production result must be reconciled to the estimate Z v * . In other words, the selection is based on Z v** from blast-hole samples, while the final production figures are reconciled to Z v * from exploration drilling. For a given preselected cutoff grade z0, the actual mining panels will consist of the units having the estimated grade Z v** =z0 rather than the true grade Zv =z0. The difference between Z v** and Zv is usually of less concern."

Jan 1, 1998

By S. Mamonov, V. ?shikhin

"The purpose of work was the significant increase of copper recovery from slag at a concentrating plant. Analysis of study of slag phase composition showed the perspective of a slow slag cooling method due to its recrystallization and transition of primary copper minerals to secondary.Copper content in base slag varied between 0.71 and 0.96%. The study of a degree of copper minerals release of the slowly cooled slag in comparison with a yielding slag showed that in a flotation size grade –0.071 mm of yielding slag the weight ratio of released copper minerals grains is 58.95% against 86.73% in samples of slowly cooled slag. The process flotation sheet consists of three main, one control and two cleaner flotation operations with aftergrinding of middling products. A reagent mode was differed from a factory one by decreasing the slurry pH from 11–12 to 8–9. This paper shows research results of the slurry alkalinity impact on technological indexes of beneficiation (flotation).Industrial testing of a resulted batch of slowly cooled slag at “SUMZ” concentrating plant showed the efficiency of such processing: copper recovery to a copper concentrate increased by 15–19%.INTRODUCTIONIntensive development of mining and metallurgy industries within a 250-year period in the Ural region led to forming of approximately 315 man-made mineral formations at the territory of the Sverdlovsk region. The region contain over 32.5 billion tons of barren rocks and out of balance ores, over 1.5 billion tons of tailings, over 115 million tons of slimes, and over 100 million tons of metallurgical slag (Demin et al., 2000). Latters, at average, contain 407 thousand tons of copper, 2519 thousand tons of zinc, 7 tons of gold, and 150 tons of silver (Rudoy et al., 2011). Wastes generated in mining processing and metallurgical sector of economy contain not only thousands tons of copper and zinc, but cause significant damage to the environment where they are located. The reduction of negative impact of anthropogenic wastes on the environment as well as the storage volume reduction of valuable metals from dump slags is possible by improving the efficiency of the melting and further flotation of slags formed during this process."

Jan 1, 2016

By J. D. Zhu

A numerical model for predicting microporosity formation in aluminum castings has been developed, which describes the redistribution of hydrogen between solid and liquid phases, the transport of hydrogen in liquid by diffusion and Darcy flow in the mushy zone, One of the key features of the model is that it uses a two-stage approach for porosity prediction, In the first stage, the volume fraction of porosity is calculated based on the reduced pressure, whereas, in the second stage, at fractions solid greater than the liquid encapsulation point, the fraction porosity is calculated based on the volume of liquid trapped within the continuous solid network, which is estimated using a correlation based on the Niyama parameter, The porosity model uses thermal data calculated using the commercial finite element package ABAQUSTM. The model has been applied to examine the evolution of porosity in a series of experimental samples cast using unmodified A356 in which the initial hydrogen content was varied from 0,048 to 0.137 [cc/100g], A comparison between the model predictions and the experimental measurements indicates good agreement in terms of the variation in porosity with distance from the chill and the variation resulting from initial hydrogen content.

Jan 1, 2005

"INTRODUCTIONThe Department of Energy, Mines and Resources has recently developed two automatic controls for use in the cyanidation circuits of Canadian gold mills. These controls are the alkalinity probe and the Continuous Cyanide Titrator both of which are discussed in the paper ""Instrumentation in the Cyanide Process"".(1)In May 1966 these process controls and associated recording equipment were installed in the Bralorne mill by two Scientific Officers from the Department. The object was to determine if the equipment was amenable and applicable to this particular circuit. The purpose of this paper is to discuss the performance of the equipment over a test period of 4 months.CONCLUSIONSThe results of test work to date indicates that both the Conductivity Probe and the Continuous Cyanide Titrator would be an as set to the operation of the Bralorne mill.The conclusions are generalized as follows:-(1) At a milling rate of 100, 000 tons per year the expected reductionin reagent consumption would give a direct saving of 37, 660 lbs of lime@$0.030 per lb and 15, 790 lbs of sodium cyanide@ $0.175 per lb. Such cost savings would pay for the equipment and installation costs within a 30 month period"

Jan 1, 1967

By C. A. Petch

Abstract - The High Lake polymetallic deposit is located in the northern Slave province, 40 km south of Coronation Gulf, Nunavut. The main zone, the AB zone, hosts an estimated resource of 3.56 Mt grading 5.0% copper, 1.1% zinc, 0.06% lead, 1.7 g/t gold, and 18.2 g/t silver. Archean felsic metavolcanic and metavolcaniclastic rocks are the dominant rock type and are associated with lesser mafic metavolcanic and carbonate-rich metasedimentary rocks. The sequence strikes north-northeast, dips steeply to the west, and is truncated to the west by a large granodioritic intrusion. The mineralization at the AB zone is comprised of massive and stringer chalcopyrite-sphalerite-pyrrhotitepyrite± galena. At the core of the mineralized zone, intensely chlorite-altered rocks are locally metamorphosed to form distinctive zones of anthophyllite-magnetite-cordierite-altered rock. Peripheral to the mineralized core, alteration consists of sericitization, silicification, and weaker chloritization. Primary morphology and facing direction of the zone are difficult to interpret in part due to poor primary metal zonation of the deposit. However, the irregular shape of the mineralized zone and the erratic zones of zinc enrichment at the fringes are consistent with the interpretation that the zone was formed by the replacement of a porous volcaniclastic pile.

Jan 1, 2004

By Tyson C. Birkett

Initial indicator mineral sampling covering 425,000 square km of northern Quebec and subsequent follow-up of positive results convinced the Ashton ? SOQUEM joint venture to acquire mineral rights to 380,000 hectares prospective for diamond in late summer, 2000. Drilling in 2001 and 2002 identified eight kimberlitic bodies, all significantly diamondiferous. Commercial size stones (retained on a square mesh sieve with openings 0.85 mm) and encouraging grades have been returned by several bodies tested to date: The Renard bodies are formed by steep-sided breccia pipes with kimberlitic matrix surrounded by irregular outboard breccia zones within country rock. These bodies were emplaced in high-grade metamorphic rocks of the Superior Province of Archean age. Orthogneiss with lesser tonalite hosts the breccias, although regionally paragneiss is also present. Diatreme facies portions and nearby country rock are intruded by minor to major (Renard 1) amounts of hypabyssal-facies kimberlitic rock. Renard bodies are macrocrystic, with large olivine crystals set in a groundmass of olivine, phlogopite, monticellite, spinel, carbonate, apatite and serpentine. Proximity of various Renard bodies, with most in a core area of 0.5 square km will allow planning of an efficient mining operation. Geophysics, especially magnetic surveying, has contributed to identifying bodies of kimberlitic rock.

May 1, 2003

By G. H. Faye

The prospect of obtaining high-grade concentrates from Canadian pyrochlore ores is rather unlikely, and experimental beneficiation pro-cesses ?appear to have yielded products in the range of 3 to 20 per cent N'b205? A possible solution of the problem is to find an economical chemical method for recovering high-purity Nb2?05 from such concentrates. A technically feasible but economically unproved process is outlined in this paper, in which the concentrate is decomposed by an acid attack and the oxides of niobium and tantalum are isolated and then separated by liquid-liquid extraction. The solution of the ore is adjusted to 7 M HF-5 M HNO3 and the niobium and tantalum are extracted from this solution with methyl isobutyl ketone. The mixed oxides of niobium and tantalum are recovered from the oxdanic phase and dissolved in 0.5 M HF-1.0 M HNO3. Tantalum is extracted preferentially from this solution with methyl isobutyl ketone, leaving niobium in the aqueous phase. By the use of this process it is possible to produce niobium pentoxide and tantalum pentoxi.de in 99.5 per cent purity with a recovery of approximately 95 'per cent, under lab-oratory conditions.

Jan 1, 1957

By Anna Maria Venezia

Bimetallic Au-Pd catalysts supported on amorphous silica-alumina (ASA) with vary amount of alumina (0, 8, 14, 28 and 100%) were prepared by the simultaneous reduction of palladium and gold precursors by ethanol in the presence of the polyvinylpyrrolidone (PVP). X-ray diffraction and X-ray photoelectron spectroscopy analyses indicated formation of alloyed Au-Pd particles. Ammonia temperature programmed desorption measurements were performed to monitor the acid strength and the amount of acid sites on the catalysts after their reduction with 10%H2/Ar at 573 K for 1h. The effect of the support acidity on the catalytic activity was investigated in the simultaneous hydrogenation (HYD) of toluene (T) and naphthalene (NP) in the presence of dibenzothiophene (DBT). Coke formation was also determined. Under the selected conditions (P = 5.0 MPa, T = 523 K, WHSV = 41.2 h-1), all the catalysts were resistant to poisoning with 113 ppm of S (as DBT). The hydrogenation activity of toluene and the HDS activity of DBT were found to correlate with the concentration of the medium strength acid sites. The enhancement of the HYD activity and the S- tolerance was related to modifications of the electronic properties of the metal atom upon interaction with the Brönsted acid sites and upon intermetallic interaction.

Oct 1, 2003

By Manouchehr Oliazadeh

Talc is used as a gelating, diluting, antimould and softening agent in the pharmaceutical industries. This article reviews efforts made for producing pharmaceutical grade talc from a mine located in the west of Iran, called Masoud Abad. Reaching to the pharmaceutical standards, was the principal goal of the talc beneficiation. Methods such as flotation and leaching were applied to eliminate the impurities. Considering to the negligible Fe content of the ore, the major impurity was calcium carbonate and to some extent dolomite. Depressants used in froth flotation were dextrine, quebraco and sodium silicate. Variation of collectors such as oil petroleum, paraffin, stearic acid were also used. After optimization of the effective parameters, followed by two stages of flotation (rougher and cleaner) acid leaching process was also applied as a complementary step to remove the impurities. CaO impurities in the sample was 11.63% which reduced to 1.03% after two stages of flotation, and finally reached to 0.03% CaO by leaching process. This figure is more lower than the world pharmaceutical standards (i.e. <0.6 % CaO). The highest recovery was 55% at the best conditions. Other impurities (i.e.As, lead, heavy metals ,?) which were at standard levels, confirmed by the authorized health organizations.

May 1, 2001

By S. D. A. Hannot, H. Knapp

"High pressure grinding rolls (HPGR’s) are an energy efficient solution for comminution of industrial minerals and metal ores. The technology is successfully applied in an expanding field of applications throughout the minerals industry. HPGR’s compress and grind the particle bed in the operating gap between two counter-rotating rolls. The equipment provides a high capacity, low energy alternative for applications with conventional tertiary and quaternary crushing and grinding, with size reduction reaching from 100mm down to 25 microns product. In this process, maintaining a controlled and evenly distributed operating pressure between the rolls is very important. Due to feed segregation, the pressure distribution along the roll’s length can become uneven, resulting in a coarser product. This paper will show that the best approach to compensate and adapt for the uneven pressure is to allow the rolls to skew relative to each other. Coarser products are also caused by an inadequate pressure distribution: the much-discussed edge effect. To minimise the consequence of the edge effect, an optimised ratio for the roll length to diameter will be calculated. Furthermore, the design philosophy behind a cheek plate will be detailed. This cheek plate is used to retain the material between the rolls, reducing the edge effect while still allowing roll skew. Together these design considerations help optimise HPGR’s performance.INTRODUCTION Initially developed for the cement industry during the energy crisis in the 1980’s , high pressure grinding has been an accepted technology for many years. It has been successfully implemented throughout the minerals industry, with applications in base and precious metals, as well as industrial minerals processing. The comminution process relies mainly on size reduction through to compression and inter-particle crushing in a particle bed in the operating gap between two counter-rotating rolls. The equipment typically has a high unit capacity and low energy consumption, and is increasingly used as an alternative to conventional tertiary and quaternary crushing and grinding, in particle size ranges reaching from 100mm down to 25 microns. It can be applied to moist ores and dry material, in open circuit arrangement or in a closed circuit with dry or wet classification (screening, air classification)."

Jan 1, 2019

By J. Baumbach, H. Bombach, M. Stelter

"Today technical electro-refining processes for copper exclusively use sulfuric acid, for silver refining nitric acid electrolytes are used. Sulfuric acid is characterized by very good chemical and electrochemical stability, good conductivity and low cost. The disadvantages of sulfuric acid are the precipitation of fine-grained cathodes with smooth surfaces only by using additives like glue, thiourea and chloride. In case of silver the electrolyte is electrochemical unstable and bears the risk of the formation of toxic NOx when pH is too low. A second disadvantage is the form of electrodeposition of silver as dendrites with their removal from the bottom of the Möbius cells.This paper reports the results concerning the application of an alternative electrolyte in copper and silver electro-refining. At first the electrolyte was characterized by the determination of current density potential curves. Electrolysis experiments were performed in laboratory scale using technical anodes for copper and synthetic anodes for silver. During the copper tests the solubility of contaminations from the anodes and the amount and chemical composition of the anode slimes were determined. Moreover the influence of current density, electrolyte temperature and the effect of several additives on the precipitation and chemical purity of the cathodes were investigated. In all experiments cell voltage as well as anodic and cathodic polarization was measured and current efficiency and specific energy consumption were calculated. A comparison with the results with those of tests using conventional sulfuric acid electrolyte shows the advantages and disadvantages of both systems, additionally the technical application chances and limitations for the new electrolyte. This electrolyte enables the precipitation of smooth copper cathodes with low silver and sulfur concentrations even at lower temperatures without any additive. For silver refining the electrodeposition of compact silver sheets is possible, that can be stripped comparable to those in copper electro-refining."

Jan 1, 2016

By Lin Li, Ahmad Ghahremaninezhad

"In this paper, the electrochemical behavior of ferric and ferrous couple on the pyrite surface was studied by application of the chronoamperometry technique in an acidic solution at room temperatures and atmospheric pressure. The effects of the pyrite origin, ferric and ferrous ions concentration on the electron transfer kinetics of Fe3+/Fe2+ reaction were probed. Tafel behavior of all the test conditions were developed. The results showed that the ferric-ferrous reaction on pyrite electrodes with different origins have a common mechanism, despite different reaction kinetics. The exchange current densities of the redox reaction have the same magnitude of about 10-5 A·cm-2, which is far lower than the value reported for the gold and platinum electrodes, but larger than that of the chalcopyrite electrode. The cathodic transfer coefficients are between 0.4 and 0.5, while the anodic transfer coefficients appear unusual with the lowest value being 0.23. It was also demonstrated that an increase of one order of magnitude of iron concentration has no clear effect on the exchange current density and cathodic transfer coefficients of Fe3+/Fe2+ redox reaction.INTRODUCTIONPyrite, FeS2, is mostly considered as a gangue mineral which frequently coexists with valuable minerals and metals, such as gold, copper and nickel. Its separation from valuable minerals can be a costly process (Chandra & Gerson, 2010). In refractory gold ores, the fine gold particles are locked inside the pyrite structure. Oxidative leaching of pyrite is a hydrometallurgical method to destroy the structure of pyrite and expose the fine gold particles to the cyanide solution in the downstream cyanidation circuit. Pyrite oxidative leaching can be achieved by oxidation of pyrite via oxygen and ferric ion(McKibben & Barnes, 1986). In fact, pyrite oxidation by oxygen and ferric is a significant source of acid mine drainage(AMD), which adversely causes serious environmental problems(V. P. Evangelou, 1995).The pyrite oxidation mechanism is accomplished in three consecutive steps: (i) pyrite is oxidized by oxygen and ferrous ion formation (Eq. 1); (ii) ferrous oxidation by oxygen and ferric ion formation (Eq. 2); (iii) pyrite oxidation by means of ferric ions (Eq. 3). Hence, both oxygen and ferric participate in the pyrite oxidation process (Moses & Herman, 1991):"

Jan 1, 2016

By J. Lu, M. Mohammadi, C. Pelletier, B. Wassink

Chemical reduction of selenate by chromous ions is proposed as a novel method to remove selenate from sulfate-bearing solutions Chromous ions were generated by electrochemical reduction of chromic ions using an electrochemical cell. The investigation was conducted in sulfate medium and under various concentrations of chromous ions (0.0062 to 0.05M), pH 1 to 2.2 and temperature 10 to 60°C. Selenate ions were rapidly reduced by chromous ions to hydrogen selenide. The overall reaction at a chromous/selenate molar ratio of 8 or higher can be expressed by the following reaction. At an initial chromous/selenate molar ratio below 8, the products are hydrogen selenide and elemental selenium. At a lower chromous/selenate molar ratio and pH, more elemental selenium and less hydrogen selenide are produced. The reduction kinetics is controlled by both chromous ion and hydrogen ions concentrations. The reaction rate is first order with respect to selenate, hydrogen ion and chromous ion concentrations. It was found that the selenate reduction rate with chromous is independent of the concentration of sulfate present in the solution. The general rate equation was proposed and the rate constant was calculated as k= 0.38 M-2s-1. An activation energy of 58.7 kJ/mol was obtained in the temperature range from 10 to 50°C. Nearly 100% of selenate can be reduced to H2Se from solution containing 17 ppm selenate in less than 30 minutes at pH 2.2 and 60°C. Various strategies have been tested to remove the produced H2Se from solution. INTRODUCTION Selenium in nature is mostly associated with metal sulfide minerals such as copper, iron, zinc, and lead sulfides (Zingaro & Cooper, 1974). The extraction of metals from ores has the potential for selenium contamination of ground and surface water which can pose an environmental and health concern. Therefore, selenium contamination in the receiving environment is a key issue for many industries (specifically copper industry) and the treatment of wastewater contaminated with selenium is a growing challenge. The effective removal of selenium from contaminated water is very important to support sustainability in the copper industry and the other industries with selenium pollution issues.

Jan 1, 2019

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

An optimized long-term mine planning determines the best order of material extraction, so that the Net Present Value (NPV) becomes maximum. In the case of oil sands surface mining, one of the key constraints in NPV maximization is the volume of tailings slurry that will be generated downstream. Specifications of tailings slurry are also important from environmental perspective. Moreover, most of the material that will be used for the reclamation of tailings ponds in later periods is generated in extraction and processing of oil sands. In this paper, an integrated optimization framework is proposed to maximize the NPV of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. The proposed model is coded in Matlab and has been run using CPLEX for verification. The results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Aug 1, 2013

Building block cave operations involves significant commitments to capital and time before arriving at completion or full scale production. The focus of the mine planners is habitually to minimize the upfront capital and achieve target development rates and construction dates. However, management of the construction of block cave projects requires understanding of the strategic/tactical decisions that the project planners can take to increase the value of the project and cope with schedule risks. As block cave projects involve development of vertical and lateral access to the underground footprint and ore body, more attention to uncertainties is required as most of those projects need to confront delays leading to a decrease in value. The standard process of development and construction scheduling is often not planned with provisions to realise uncertainties in the construction phase. Uncertainties and risks such as poor ground conditions and equipment breakdowns are the primary reasons for schedule slippage. As a result most of these projects experience delays. In order to mitigate risk to the project schedule, we centre our attention on increasing the value of the project by spending more money upfront and improving the schedule rather than focus on minimizing the upfront capital. Scenario-based simulations along with project appraisal methods hold great promise to address those challenges and enable mine planners to make better decision and enhancing project value. This paper will present a hybrid simulation based approach to model the process of development and construction based on discrete event (DES) and continuous based simulations (CBS). Such simulations will be conducted for scheduling multiple development headings (Apex, undercut, extraction, and haulage levels). Two scenarios are utilized to investigate the impact of risks on schedule and how flexibility in construction can be incorporated to minimize delays: (1) The bench mark scenario is created based on actual data from an existing case study. (2) The flexible scenario is an alternative way to use primary production infrastructure (Ore Handling System) including conveyer drifts, conveyer belt, and a gyratory crusher in the construction process and that requires the system to be in place before starting lateral development in the footprint. As a result, a truck-load system versus a conveying system will be studied to observe the gain in construction speed and to estimate the premium cost for mucking rock from headings and drawbells and transporting it to surface. Such strategic flexibility would be part of the original budget to make the tactical flexibility available during construction. Continuous cash flow models are used to evaluate and compare the scenarios. This study is an example of how new techniques in planning can be used to support decision-making processes in block cave design.

Aug 1, 2013