Search Documents

By K. J. Griffin, G. W. Rosval

"In our increasingly competitive market, attempts to improve productivity by increasing axle loads have placed more severe demands on rails. CP Rail thus requires stronger, tougher, and more wear-resistant rails from steel manufacturers. The choice of any rail steel is always a compromise between technical and economic factors. The technical assessment of a candidate rail consists of laboratory and field testing. Laboratory evaluation of rail steels cannot adequately model many service conditions and must, therefore, be supplemented by long-term field testing. The field testing conducted on CP Rail is the subject of this paper.Long-term, in-track, assessment of candidate rail steels begins with the selection and re-laying of a test curve representative of the intended service with both the candidate rail and a control rail steel (i.e. the present intermediate or premium rail standard). The wear performance of the candidate rail is evaluated, in relation to that of the control rail, using data obtained with a rail profilometer developed by the Research and Development Department of CP Rail. Qualitative observations are also periodically made to evaluate the relative susceptibilities of the two rail types to surface defect formation. Testing continues until stable metal loss patterns are achieved. Relative life predictions are then made and detailed monitoring of the test site is discontinued.CP Rail's in-track assessment program for premium rails has resulted in the establishment of a new CP Rail premium rail standard - low-alloy, head-hardened, rails have replaced high alloy rails. The wear/fatigue lives of these new premium rails exceed those of our previous standard by more than 50%, and they also exhibit excellent weldability. CP Rail will continue to evaluate new premium and intermediate strength rail products."

Jan 1, 1988

By G. Castillo, G. Thies, C. Bissue

"Newmont’s Phoenix mine began gold production in 2006 and has since experienced difficulties in reaching design throughput due to variability in ore hardness. In 2010, a debottlenecking study was conducted, generating multiple options to increase throughput of the existing Phoenix Mill through a series of phased expansions. An option was selected in early 2011 to increase the current concentrator capacity by approximately 25% through two phases. The first phase of the project was the installation of a secondary crushing and screening circuit in order to reduce SAG feed size from a P80 of 6 inches to 2 inches. The second phase focuses on downstream unit operations in the concentrator aiming to relieve existing bottlenecks such as flotation. This paper analyzes the design, commissioning, and operation of a recently installed SAG Pre-crush circuit (Phase 1). The design discussion will focus on concept development, flowsheet design, design criteria, process models, design limitations, and control philosophy. Discussion on the integration of operating data and flowsheet into design during engineering will be presented. Actual operating data of major equipment is gathered from the commissioning and operation of the circuit and compared to the initial design models. Conclusions will be drawn on equipment design factors used during engineering, and the success of model integration into operation. The paper concludes on the successes of the project and where improvements can be made during design.INTRODUCTIONThe Phoenix mine is located within 25 miles of the town of Battle Mountain, Nevada. The mill processes copper, silver, and gold ore. Production started in 2006 and has since struggled to reach the designed tonnage of 33,600 stpd due to the variability in ore hardness. In production year 2010-2011, the Phoenix mill average daily throughput of 33,000 stpd. In 2008, a larger primary crusher (FLS 60/89 gyratory crusher) was installed to operate in parallel with the originally supplied primary crusher (Metso 50/65 gyratory crusher), in order to provide additional capacity upfront in the circuit so that the primary crushing circuit could keep up with the mill.In 2010, a mill debottlenecking study was completed to assess the various options that could be implemented to increase the current mill capacity. The study was completed in late 2010 and contained four tonnages that Phoenix could achieve through various expansion scenarios. A single option was selected in early 2011 to increase the mill capacity from 33,000 stpd to 48,000 stpd. The selected option looked at a four phased expansion that would increase the capacity of the Phoenix mill and address the mill’s current bottlenecks:"

Jan 1, 2013

By Don Thompson

It isn?t a lie if you don?t tell the whole truth The pictures National Geographic didn?t print Other photos National Geographic didn?t print?

May 1, 2009

By J. Hu, F. Lin, R. Chen, F Peng, S. Yang, W. Yu

"Microseismic monitoring technology has become one of the most effective method of mine ground pressure monitoring after decades of development. But safety assessment of mine ground pressure by using microseismic monitoring is still in the development stage, it needs to be perfected continuously in practice, and choose the optimal assessment indexes and methods. The definitions and physical meanings of wave velocity, b value, and EI-VA value are introduced in this paper. Statistical calculation of the microseismic events in Luomu Mine is finished by using these indexes, then the functions and calculation results of V, b value, and EI-VA value with the variable of time are also given in the paper. The preliminary safety assessment method is established in Luomu Mine, and it has achieved good results in practical application.1.1 Engineering background The Luomu Mine is a super large molybdenum and tungsten production base in China, ore reserves is up to 2 billion tons, first in Asia and third in the world. It begins mining since the 1960. and bases on underground mining until 2002. In order to recover resources more effectively, it began to use opencast mining method and formed a production of 30000t/d in the early 1990. After about 30 years of underground mining, a large mined out spaces was formed under open pit mine, up to area of 1.2 million m2 and volume of 18 million m3, as shown in figure 1. The large number of mined out spaces seriously affects the normal production, mining and handling of mined out spaces are in the high risk. In the past years, several rock mass collapsions happened, and it caused a serious security threat to persons and equipments. According to the distribution characteristics of mined out spaces, Luomu Mine is divided into A, B, C, D and E mining area. The stability of D mining area is studied in this article. D mining area mainly includes 1376,1350,1340,1317 mined out spaces and 1280 deep large mined out area, as shown in figure 2. The mined out spaces of D mining area is extremely complex and high-risk. Therefore, a microseismic monitoring system was built to monitor the stability of D mining area, a large number of valuable datum has been obtained, and it has a striking effect (Cheng & Peng, 2013; Peng et al., 2013)."

Jan 1, 2015

By David Clarry

?The issue ?reduction requirement ?Planning abatement steps ?Energy Management & Energy Efficiency ?Energy Recovery / Utilization ?Alternative Energy Professional Services Overview ?Capital Projects and Construction ?Project Development and Planning ?Engineering ?Project management ?Construction management ?Consulting ?Process ?Business ?Environmental ?Technology ?Operational Services ?In-house engineering services for operations

May 1, 2009

By Rory Cameron, Chuck Edwards

"Stringent environmental performance criteria and regulations, and the desire to minimize water use have made membrane-based treatment and separation processes an attractive option. This has lead to many advances in all aspects of the technology. Membrane separation processes have found application in sea water desalination, brackish water treatment, decontamination of ground water, and wastewater treatment. Development of membranes with better resistance to harsh feed conditions has created new opportunities for the broader application of membrane separation technologies to mineral processing streams. There are examples in mineral processing operations, including treatment of acidic drainage, pre-concentration of pregnant leaching solution in heap leaching operations, separation of acids and metals from waste streams and intermediate process streams, as well as gold and cyanide recovery from a heap leaching operation. This paper provides a brief overview of membrane technology principles, followed by a discussion of current membrane technology applications relevant to the mining and mineral processing industry. The paper further explores the potential for the application of membrane separation as an integrated component in mineral processing operations.INTRODUCTION Increased regulatory pressures, emphasis on water conservation, and scarcity of water in arid regions have resulted in substantial changes in industrial practices in recent years. As a result, many industries have become more open to adopting innovative technologies such as membrane separation. The mining industry, which is typically very conservative, has adopted membrane separation as an effective end-of-pipe solution for effluent and acidic drainage (AD) treatment; however, its use as an integrated component in plant operations has progressed more slowly. With increasingly stringent environmental regulations coupled with the desire for low- and zero-discharge operations, the use of membrane separation technology for achieving acceptable environmental performance may be unavoidable in the future. The relatively small footprint requirement, versatility, and modular construction of membrane separation units facilitate their introduction into existing processes with a suitable feed stream. Membrane separation is not a stand-alone process that provides the ultimate solution to water and wastewater treatment; however, it can often be economically added to conventional waste treatment plants to increase throughput and/or decrease contaminant output (Mortazavi, 2008). Although membrane separation technology has become an established separation technique that is widely used in drinking water production and other industries, it is still considered an emerging technology within the mining and mineral processing industry. This technology offers many potential benefits such as clean water recovery from wastewater, significant reduction of volume requiring conventional treatment, decreased usage of reagents, and acid recovery, all of which lead to increased treatment efficiencies and lower reagent consumption. This could translate to smaller and more efficient plants with lower capital and operating costs and lower environmental impacts. Plant expansion may be facilitated by incorporating a membrane separation unit operation in order to utilize existing treatment systems at higher throughputs."

Jan 1, 2012

By N. Shi, T. G. Joseph

The design of dippers for cable shovels has essentially remained unchanged for the last 100 years. In the past 10 years, shovel manufacturers have started taking another look at dipper design, resulting in changes that have borne models from major manufacturers that address some of the wear conditions and material retention problems that dominate maintenance and operational costs. However, with the exception of added lateral curvatures to the front and corners of the dipper, the geometry is essentially unchanged. This paper looks at the criteria that have resulted in the first new cutting dipper design in a century. The design is based on kinematic considerations, reflected in a revolutionary geometry that matches the range of motions of the shovel, designed to minimize wear, impact loading and power required to dig, thus maximizing productivity for a minimum energy requirement. The shape configuration is such that the weight of the dipper is reduced through wall thickness, enabling a larger capacity dipper to be conceived for the same shovel. Benefits are reflected in reduced operational and maintenance costs and increased productivity.

Jan 1, 2006

By M. Tarvainen, J. Kallioinen

"Depressed metal prices coupled with increasing production costs have presented a great challenge for operators to control and reduce the costs of production to maintain profitability. Depleting ore reserves, added to the above has forced Outokumpu to take a hard look at its operations, to develop new methods to profitably extend the life of its mines. One of the areas investigated and approved for further development has been the use of larger and more energy efficient equipment. As a result, large flotation machines were developed and today 38 and 60m3 flotation machines are in use.Secondly, ore preconcentration has been developed to avoid processing the part of the ore that has little or no mineral values.Another quite recent development and the topic of this paper, has been the use of coarse flotation before conventional flotation. The main idea is that part of the valuable mineral is separated as early as practical by floating it with specially designed flotation equipment, installed in the grinding classification circuit. The new flotation cell is specially designed for this application and differs from the conventional cells in the tank design, feed arrangement and modified mechanisms in some cases."

Jan 1, 1984

By C. A. Horne

"The transportation of mineral solids in the form of slurry is a subject most of us are associated with and, in fact, live with on a daily basis. The design parameters of slurry systems and most important the prime movers or cent¬rifugal pumps, are frequent and often controversial subjects due to the lack of practical guidelines which, if known and followed, can increase both reli¬ability and service life of the equipment.In this talk, emphasis has been placed on the practical side or rule-of-thumb approach to applications which, in turn, has been related to successful field results. The theoretical content and complex design criteria associated with actual equipment design has consequently been held to a minimum in the following discussions.I. BASIC SLURRY PUMP DESIGN CONSIDERATIONSFirst, to better understand how a centrifugal pump performs work, a basic description of the operating principles are in order.A. Operation In a pump, mechanical energy is transformed into pressure energyby virtue of the centrifugal force exerted by the rotating impeller. The liquid is discharged by centrifugal force at a velocity required to generate a given head and the volute collects the liquid so useful work can be done by the conversion of kinetic energy to pressure energy."

Jan 1, 1976

By D. M. May

"Cut-and-fill mining is a stoping method that has been widely utilized in the mining industry over the past forty years. It took preference over shrinkage methods at Levack in the early 1930sbecause of its safety aspects; i.e., prompt support of the stope sidewalls, good working floors and better accessibility to support poor back areas. In addition, higher recoveries of ore were possible because of the flexibility of the method in that silling could take place easily at any horizon; low-grade ore could be sorted and left in the stope as fill and certain zones of rock could be left unmined. With modern techniques, a steady production rate can be established, as filling and mining can be carried out stimultaneously.AIthough there are numerous variations of cut-and-fill mining throughout the world, this paper reviews the original type of mining, with modifications and improvements through the years to present modern practices, with the Levack West operation appearing to be the most productive at this time. Stoping efficiencies have also increased substantially from the original 10 tons per manshift to the present 55 tons per manshift.The paper also outlines the many improvements that have been made with respect to mucking and ground support operations; from hand mucking in a single stope to the use of frontend loaders and haulage trucks in fully accessible stope complexes; and from timber props to roof bolts of various types. Although present methods are extremely satisfactory, experimentation is continually being conducted to improve safety and productivity for future mining.IntroductionThe major mining operations of the Ontario Division of Inco Limited are located in the Sudbury Basin (Fig. 1). Around the rim of this geological formation and within 30 miles of the City of Sudbury are nine producing mines and one ' open pit operated by the company .Ore production currently approximates 11.5 million tons per annum from underground and open-pit operations. Underground mining methods include sub-level caving, shrinkage, cut and fill, undercut and fill, blasthole and vertical retreat. The Levack Complex, the main plant of which is the central Levack Mine, produces 11,000 tons per day.The first prospecting in the Levack area, in 1887, was conducted by James Stobie, who examined rock cuts along the route of the Canadian Pacific Railway to the northwest of Sudbury. However, it wasn't until 1913 that operations commenced at Levack under the Mond Nickel Company."

Jan 1, 1981

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

By Franciszek Letowski

"Recovery of precious metals associated with a sulphidic matrix has an important economic effect on complex sulphide ore treatment. Because a significant portion of the silver and gold associated with pyrite are rejected to tailings during the selective flotation of pyritic Zn-Pb-Cu ore, other ore processing routes have been investigated.Direct leaching of the ore with ferric sulphate solution followed by separation of different components of the solid suspension by flotation was applied. Such a process allows for: production of zinc sulphate solution; transformation of galena PbS to insoluble lead sulphate PbS04 and its accumulation in a non-floatable fraction together with precipitated geothite FeOOH and other insoluble gangue minerals; separation of sulphur and non-decomposed sulphides in the floatable fraction.Laboratory research carried out on the ore samples from an Alaskan pyritic deposit from the Delta region indicates that gold and silver are mostly concentrated in the floatable fraction.Total recovery of zinc from the ore attains 96.5% to 98.5% after ferric sulphate leaching. About 85% of copper was extracted from the ore during the ferric sulphate and subsequent ferric chloride leaching, and about 6% of the copper remained in the non-floatable fraction and mixed fraction during the leaching-flotation step. Extraction of lead from the nonfloatable fraction during leaching with calcium chloride solution attained 98% to 99%. Extraction of silver from the floatable fraction during leaching with ferric chloride solution reached 98%. Extraction of gold from the floatable fraction during cyanide or thiourea leaching reached 71% to 89%. The results of the laboratory research are presented."

Jan 1, 1987

By Don Langlois, Udo Weber

"The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected milling conditions of calcium carbonate. A variety of grinding media material and bead sizes, along with 2 different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data was used to calculate and evaluate specific energy as well as stress intensity under different milling conditions.INTRODUCTIONAs a result of increasing energy costs and raw material prices it is important to look at the efficiency of the manufacturing process. Wet grinding and ultrafine wet grinding in stirred media mills are now a possible cost-effective production step for the processing of industrial minerals and precious metals. The generation of smaller particle sizes (down to micrometer scale) can be advantageous for further production steps – i.e. better liberation of precious metals or improved industrial mineral qualities.In the following, the wet grinding process is investigated under different milling conditions of calcium carbonate. Different grinding media materials varying in specific weight, bead size and stirrer tip speeds are used to determine optimal energy consumption for the milling process.DESCRIPTION OF TEST CONDITIONS AND PARAMETERSMill ParametersTests were performed in a Drais Laboratory Perl Mill PML H/V with an installed electrical motor power of 3 kW. The mill chamber is silicon carbide where as the stirrer and discs are made of yttria stabilised zirconia. The mill working volume is 0.9 l. A screen cartridge with a screen size of 0.2 mm is used to separate the beads and slurry at the outlet of the mill. All tests were performed with a grinding media filling grade of 80% (Mill working volume). The stirrer tip speed was set at 6 m/s and 10 m/s."

Jan 1, 2009

By Cameron J. Clayton

Cumberland Resources Ltd. is currently planning to develop the Meadowbank Gold Project located some 70 km north of Baker Lake, Nunavut in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of up to 6 main gold bearing deposits within relatively close proximity to one another which are planned to be mined primarily as a truck-and-shovel open pit operation and using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of 8 to 10 years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11 °C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site, and the physical environment, pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project.

May 1, 2004

By Pablo González, Rodolfo Espinosa, Jose-Luis Noyola, Sergio Cossio

"Minera Penmont, at La Herradura, is a joint venture between Industrias Peñoles, S.A. de C.V., and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with two-stage crushing and heap leaching facility, the gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130,000 gold ounces per year, and treatment capacity is 22,000 tonnes/day. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to the coarse visible gold, in some coarser particles ranging from 100 to 600 microns.Sampling and assaying protocols where established during exploration and prior to starting up operations, based on nomographs developed from early heterogeneity tests. But, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block made of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to starting up operations (“existing”) and the new protocol (“leaching”). In the “existing” protocol, subsampling is done through riffle splitters, and coning and quartering. Fire assaying is used to estimate the gold content, on a 50 g sample. In the “leaching” protocol a 12,000 g sample was bottle rolled cyanide leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this “rotary sampling” protocol and for comparison purposes, gold assays were also repeated using the “leaching” protocol.Test results were compared in three groups < 0.30 g/t (below cut-off), 0.30 to 0.8 g/t, and >0.8 g/t. Overall. Results show that the protocol established prior to starting up operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2003

By Rosaire Emond

Le concept du forage horizontal a été développé voilà de nombreuses années. Différents types de plate-formes permettant le forage horizontal depuis une cheminée ont été conçus par divers manufacturiers ou opérateurs miniers. Entre autres, on connaît bien la griffe de montage Alimak à laquelle peut être fixée une plat-forme sur laquelle est montée une foreuse. En 1992, Ross-Finlay a développé sa propre plate-forme de forage qui à notre opinion améliore la flexibilité du concept du forage horizontal, en augmente la productivité et en diminue le coût d?ensemble tout en assurant une sécurité accrue des travailleurs. Tel que montré à la figure 1, la plate-forme employée à la Mine Kiena est composée d?un toit de protection contre les chutes d?objets et de deux passerelles de forage de forme carrée. Le toit et les passerelles sont fixées à une structure de 6.5 m de longueur équipée de deux assemblages de rouleaux (non montrés à la figure) permettant de faire glisser l?ensemble sur des rails Alimak. L?angle du toit et des passerelles peut être ajusté pour des cheminées dont le pendage varie de 65 degrés à 85 degrés.

Oct 1, 2001

By Tano Balbin, Valery Astakhov, Juha Timperi, Lauri Koresaar

"Online elemental analysis is the basis of optimal flotation control in mineral concentrator plants. Traditionally XRF analyzers have been used as the online analysis method. However, online XRF analyzers struggle to measure elements below calcium in atomic number (Z=20). For many processes lighter element assays would be beneficial to improve control of grade and recovery. Processes where elements below Ca are required include P, Mg and Si in phosphate concentrators, Si, Mg and Al in iron concentrators, and S and C in gold concentrators. Laser-Induced Breakdown Spectroscopy (LIBS) based elemental analysis can readily be applied to these processes. LIBS is based on generating plasma in the slurry sample by a high energy laser and analysis of the plasma by optical emission spectroscopy. Capabilities of a new Courier® 8 analyzer based in LIBS technology are demonstrated for elemental analysis starting from lithium (Z=3). Results of a plant installation in a sulfide gold concentrator provide a good agreement with the analyzer and laboratory assays.IntroductionEffective process control can be regarded as one of the fastest paying investments for a mineral processing plant. Process optimization in flotation circuits requires constant feedback of the process state. If only manual laboratory samples are available, this optimization becomes difficult due to the long delay between taking the sample and acquiring the laboratory result. If the element grades are available in online basis, the operator or automatic process control system can make corrective actions in real time.Online X-Ray Fluorescence (XRF) analyzers have been in use at concentrators for decades. The XRF analyzers can provide a fast, accurate and precise analysis from slurry streams. However, the drawback of XRF analyzers is their lack of capability to measure elements below Ca (Z=20) in atomic number. The low energy X-rays of the low atomic number elements get absorbed by water in the sample, protective window of the analyzer, or air between the sample and spectrometer."

Jan 1, 2017

By C. J. Van Treeck

PGE concentrations of 18 g/t occur in the pyroxene rich rocks at the Union Bay Alaskantype complex. This PGE enrichment is hosted in magnetite veins. These veins cross magmatic layering and have an irregular morphology in both outcrop and thin section. Fe-Ti oxide geothermometry suggests that this mineralization took place between ~700-400°C. A variation in the amount of ilmenite and Mg- Al spinel exsolution in magnetite correlates with temperature estimates, lower temperature magnetite has less exsolution. Hydrous silicates form an alteration envelope around magnetite veins with a formation temperature of <575oC, vary with temperature, and contain appreciable amounts of Cl. Interaction of a PGE-Fe-Cl rich fluid with clinopyroxene increased the fluids pH and decreased PGE and Fe solubility depositing a PGE enriched magnetite within the Pyroxenites and Olivine Pyroxenites of the Union Bay complex.

May 1, 2003

By A. Wright, P. Lacombe, R. del Villar, D. Hodouin, C. Sepulveda

"The data acquisition from industrial plants is a fundamental step for process modelling in process optimization, process analysis and automatic control.The introduction, some years ago, of modern distributed control and data acquisition systems in concentrators imposes a new approach in designing experimental schemes for data acquisition campaigns and new criteria for the treatment of the obtained discrete information.This paper presents the methodology applied to sample a zinc flotation circuit at Les Mines Selbaie, Joutel, PQ. Values of 85 process variables were obtained form the Distributed Control and Data Acquisition System (Bailey Network 90) and transferred to the DOS environment. Another 11 variables (flowrates and valve positions) were directly sampled using an IBM-PC compatible computer equipped with a data acquisition card and a signal processing circuit.All variables, under the vector form, were processed in the PC-MATLAB environment to either filter or eliminate the non-linear disturbances and noises, producing useful data for model development. The filtering algorithms are also presented.INTRODUCTIONProcess control does not need to be justified. Whether manual or automatic, any processing plant requires some form of control to accomplish its main objectives: a good quality product and a target throughput. Process control of mineral processing plants has steadily evolved from manual control, where the operator skills and/or experience play an important role, to some level of automatic control, usually considered better, as less human subjectivity is involved, at least when actions have to be taken.The design of these control systems requires the knowledge of the dynamics of the process it is deemed to control. Process modelling is therefore an essential step in the assessment and the design of a control strategy. The choice of model will depend on the available resources and manpower."

Jan 1, 1991

By P. Walford, C. Mealin, D. Good

"The geology of the Ore Fault Ni-Cu deposit has been reinterpreted in the light of recent studies of the geology of the Neoarchean Bird River Sill Complex and the occurrence of economic Ni-Cu and Zn-Cu-Ag mineralization. The Ni-Cu sulfides are hosted by the lower of two parallel NNW-trending and moderately W-dipping mafic-ultramafic intrusions related to the Bird River Sill Complex. The bod¬ies intruded a bimodal volcanic suite consisting of weakly deformed mafic flows and felsic pyroclastic rocks. The mafic volcanic rocks are geochemically related to the MORB-type rocks of the Lamprey Falls Formation, and the felsic volcanic rocks are related to arc-type rocks of the Peterson Creek Formation. The original pyroxene- and olivine-dominated mineralogy of the sills has been replaced by variable ser¬pentine-amphibole-talc-carbonate assemblages.The Ni-Cu sulfide assemblage exhibits textures and geochemical signatures typical of orthomagmatic sulfide mineralization. The sulfide minerals are associated with cumulate layers of magnetic ferrochromite that range in thickness from a few to tens of centimeters. A later event of Zn-Cu-Ag sulfide mineralization associated with quartz veining and garnet-chlorite alteration along a fault that strikes north, dips vertically, and cuts all rock types. The mineralized fault is cut by the NE-trending Peterson Creek shear zone. Where the Ni-Cu and Zn-Cu-Ag mineralized zones intersect, remnant magmatic features such as amphibolite or cumulate ferrochromite bands occur within quartz veins or local chlorite alteration. The mixed zones contain a very unusual polymetallic assemblage of Ni, Cu, Zn, Ag, and platinum group elements (PGE)."

Jan 1, 2009