Search Documents

By H. B. Farnam

"THE IRON ORE Company of Canada has been using do-it-yourself type explosives for three years. During the last 12 months we have used over 10 million pounds of ammonium nitrate-fuel oil explosives and either purchased or formulated one million pounds of slurried explosives.W e have been moving approximately one million cubic yards of stripping and ore per month and we expect our production rate to in-crease. Eighty per cent of our strip-ping and ore is soft enough to be blasted successfully with ammonium nitrate-fuel oil mixtures. Twenty per cent of our material is extremely hard and requires an explosive having greater strength than an AN-fuel oil mixture.W e had been using canned am-monium nitrate base explosives and TNT pellets to give maximum bottom loading density to fracture hard rock. As AN -fuel oil became widely used, it was apparent that other types of explosives could be formulated to fit our blasting requirements. Dr. M. A. Cook of the University of Utah was consulted regarding new explosives and together we developed the blasting slurries.Figure 1 shows a general view of one of our hard rock pits. The foot wall is on the right-hand side and this material is called iron forma-Figure 1.-General view of hard rock pitstion by our Company but is called 'Taconite by the operators on the Mesabi Range. This material runs 35 to 45 per cent iron and many pieces are hard enough to scratch glass. The formation is tilted at an angle of 55 degrees as can be seen in Figure 3.The bedding planes of this rock are about 24 to 36 inches apart and if the material is not well broken or fragmented, large chunks or slabs must be handled by the shovels which reduces shovel capacity and efficiency and increases maintenance costs."

Jan 1, 1960

By J. B. De Hart

This paper has been confined to the consideration of the working of thick seams, from six feet to sixteen feet, which are pitching at about thirty degrees to the horizontal. The discussion has been limited to these set conditions because they are the ones of commonest occurrence in the Southern Alberta bituminous coal district, because, from the point of view of safety, thin seams are more easily worked, and because a discussion of all the possible combinations of thick and thin seams pitching at angles varying from zero to ninety degrees with the horizontal would involve a task impossible in the time available. It has been assumed that the mine makes gas freely and that the coal is friable and tends to make inflammable dust which is highly explosive. Since the problem requires the taking into account means of maintaining a high proportion of lump coal, it is further assumed that lump coal commands a price considerably higher than the price which can be obtained for run-of-mine or for slack coal. Figure 1, tabulating the various factors which must be considered and their relation to each other, indicates diagrammatically the complexity of the problem. Any method of working becomes divided into two distinct components, the active workings of the mine and the old abandoned workings. While these are in a measure distinct, they are nevertheless inter-related, as shown in the diagram.

Jan 1, 1930

By V. K. Karra

"A simplistic algorithm jar simulating the rod or ball mill Bond grindability test applied to ores and minerals is presented. A performance comparison between the present algorithm and a previously published algorithm by Kapurot, modified in this work jar a fair evaluation, is also given. A worked example is furnished jar leading the reader through the various calculations.IntroductionThe Bond grindability test is widely used for the prediction of the power requirement of an industrial grinding mill. The procedures for conducting this test in either a ball or a rod mill are available(1). In the case of a ball mill, batch grind abilities have been correlated to Bond grindabilities to help monitor day-today variations in ore grindability for the purpose of plant control( 2,3). Of special interest is the algorithm presented by Kapur(3) for the simulation of the Bond test. In practice, the test lasts from 6 to 14 cycles (4 to 10 hours). With this algorithm, one can predict the Bond grind ability using information available from only the first two cycles.Sometimes the prepared feed for the grindability test contains too much fines compared to the total product desired at the mesh of grind under consideration. In such a case, the operator separates the fines from the test feed and adds to the remaining coarse fraction an equal amount of fresh feed. This combined feed then forms the feed to the first cycle of the test. In the present work, Kapur's algorithm is modified to include this special case. A new and relatively simpler algorithm is also presented. Statistical equations relating work index to pertinent variables are also given."

Jan 1, 1981

By Gregg W. Morrison

"The Craigmont copper-iron skarn deposit is adjacent to the southern margin of the late Triassic Guichon Creek batholith in south-central British Columbia. Host to the ore are sedimentary and volcanic rocks of the western calc-alkaline belt of the Upper TriassicNicola Group. In the mine area, the Nicola Group rocks are a stratigraphically complex sequence, at least 1800 feet thick, which have been subdivided into Basalt, Rhyolite, Carbonate and Clastic Sediment units. All the units strike and dip parallel to the margin of the Guichon Creek batholith and are within the batholith contact aureole. However, only the Clastic Sediment unit is in contact with the batholith.Most of the skarn and ore is within the Carbonate unit and more specifically within an Interbedded facies that consists of lime sandstone, lime siltstone, quartzo-feldspathic siltstone and argillite. The Interbedded facies and the adjacent barren Massive Limestonefacies are interpreted aspart ofa carbonate reef complex. The distribution of skarn and ore within the Interbedded facies suggests that the facies boundary was a physical and chemical barrier that resulted in concentration of metals adjacent to the Massive Limestone facies.Two stages of skarn formation have been recognized at Craigmont. In Stage I, ore-bearing magnetite-rich and actinolite-epidote-magnetite skarns developed both in basaltic rocks and in Fe-bearing siltstone and argillite of the Interbedded facies, while barren grossular garnet-epidote-calcite-pyrite skarns developed in Fe-poor rhyolitic bands within the Interbedded and Massive Limestone facies . In Stage ll, massive, barren grandite garnet skarn replaced mineralized Stage I skarns in the vicinity of diorite plugs. and specularite ore formed in brecciated Stage I skarn and clastic rocks away from the plugs. Theformation of Stage I skarns required no addition of material, only redistribution and concentration of elements already present within the Interbedded facies. However, the concentration of Cu in Stage lore requires a mechanism for more efficient leaching of Cu from the host rocks, an anomalous concentration of Cu at the site of the Stage I orebody or an additional input of Cu from an external source. The formation of Stage II skarn and ore requires only remobilization and recrystallization of Stage I skarn and ore.Copper and iron are the only elements in economic concentrations in the ore and chalcopyrite is the only significant copper-bearing mineral. Chalcopyrite is disseminated and interstitial to magnetite in Stage I mineralized skarns and is interstitial to specularite in the matrix of Stage II breccia ores. Chalcopyrite also occurs with pyrite as stringer ore in bleached • sediments and rhyolite tuffs in the stratigraphic footwall of the main orebodies.The Craigmont deposit has more features in common with Cu-Fe deposits hosted in metavolcanic and metasedimentary rocks than it has with typical skarn deposits associated with porphyry copper deposits. The orebody is more likely a product of concentration of metal contained within the Nicola Group rocks than of the mineralizing event that produced the . Highland Valley Cu-Mo porphyry deposits in the central part of the Guichon Creek batholith ."

Jan 1, 1980

The methods employed for the addition of uranium to steels and cast iron in the Physical Metallurgy Division are outlined. It has been found that the segregation of? uranium is a major problem in aluminum and/or silicon killed steels and that the cooling rate is important in al-lowing the segregate to settle to one area, which can subsequently be discarded. The unsegregated areas were found to be extremely low in total oxygen, acid insoluble aluminum (AizOg) and, in some cases, slightly lower in nitrogen. Uranium recoveries, based on analyses of the unsegregated areas, were quite constant, at about 45 per cent, regardless of the type of uranium master alloy used for the addition. No segregation of carbon, manganese, silicon, sulphur, phosphorous, chromium or copper was observed in these steels. In commercial heats, the recoveries ranged from 7 to? 29 per cent for ladle additions to oxygen converted steel. When the steel was fully deoxidized prior to the uranium addition, recoveries ranged from 49 to 66 per cent, regardless of the steelmaking process.

Jan 1, 1964

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. T HE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept Iles,

Jan 1, 1965

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. THE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept-lies, a seaport

Jan 1, 1965

By R. D. Brown

"""A matter of serious concern to the mining industry in British Columbia""; this comment reflects the attitude of the Mining Association of British Columbia toward the proposed new B.C. Mineral Royalties Act. The proposed legislation, introduced by the provincial government in February and now being debated by the legislature, combines a basic 5% royalty on the selling price, less approved p1ocessing and transpo1•tation costs, of minerals produced in B.C. with an ""excess"" royalty of 50% of any price increases over a predetetmined base. Government estimates project annual revenues of $20 million from the new royalty structure. The accuracy of these figures has been contested by the mining industry. Based on current world prices for copper the industry estimates that the provincial revenues from this mineral alone may run as high as $140 million in 1974 and $150 million in 1975. The Mining Association has warned that the new royalties “threaten to become confiscatory""."

Jan 1, 1974

By M. Mai Manga, M. Renaud, A. Faucher, C. Bazin

ABSTRACT Grinding circuits are operated in the presence of disturbances resulting from ore changes and equipment malfunctions, such as hydrocyclone overloading, worn or partly plugged apexes, surging, and internal liner detachment that may cause a loss of classification performance. Metal recovery losses in downstream leaching or flotation circuits justify the development of methods for rapid detection of hydrocyclone malfunction. Two methods are presented in this paper. The first method uses measurements from sensors available in a grinding circuit and the second uses vibration sensors installed on the individual hydrocyclones of a nest.

Jan 1, 2011

By J. M. Réjean Gagnon

"Quebec Cartier Mining Company is currently mining a low-grade iron ore deposit in northeastern Quebec. The Company is producing some 8,000,000 dry gross tons of concentrates per year, grading about 66 per cent iron. The pit, which is located on the keel or hinge line of a fold, will eventually be about 1,000 feet deep with a surface area of 8,000 by 2,600 feet. The most significant structural discontinuities in the mine are the natural bedding planes and secondary perpendicular joints. The exposed walls are subjected to a sub-Arctic climate and heavy blasting occurs approximately six times a month.QCM utilizes design and operating techniques to control rock fall. Steps are also being taken to analyze the ultimate over-all pit slope stability."

Jan 1, 1968

By O. Babak, J. G. Manchuk

ABSTRACT A significant factor in evaluating bitumen recovery from an oil sands mine is the particle size distribution (PSD). Increased understanding of mined ore quality and improvement in predictions of recovery can be achieved through PSD modeling. This paper addresses PSD modeling using geostatistics. PSDs may be described using many discrete particle sizes, making this a challenge. The approach parameterizes PSDs with a few statistics. A lookup table is used to reconstruct the PSDs based on models of the statistics. The workflow is applied to Total E&P Canada’s Joslyn Lease and yields good results that reproduce input statistics without introducing artifacts.

Jan 1, 2013

The Carboniferous sedimentary rocks of southwestern Newfoundland merit investigation because of petroleum, salt and gypsum possibilities and indications of base metallization along the equivalent of the Horton-Windsor con-tact. In this paper, Lower Mississippian (Anguille) strata are divided into three formations: (1) the Cape John below, (2) the Snakes Bight and (3) the Seacliffs. A correlation between these formations and the Craignish, Strathlorne and Ainslie formations of the Horton group? in western Cape Breton Island is suggested. The criteria for the Anguille subdivision are essentially lithological, but preliminary study of included spore assemblages suggests more precise interformational correlations between Anguille and Horton sequences. The re-measured lower portion of the type section of the Codroy group is presented to define more clearly the stratigraphic position of numerous gypsum and limestone beds. Because of rapid facies changes within the Codroy group a simplified two-fold division into upper and lower units is proposed on the grounds of

Jan 1, 1964

By G. F. Round

In order to obtain values of angle of shearing resistance and initial resistance for McMurray oil sand for use in general design calculations, the shear strength of this oil sand was measured in a controlled strain type tester, modified so that the rate of deformation could be varied between 0.01725 and 0.1869 inches per minute. Effect of temperature was investigated by adapting the equipment to operate at both 71 ° and 185 °F. The data are reported in terms of angle of shearing resistance and initial resistance for varying rates of deformation, composition and temperature. While the main sets of results reported here were obtained at a bulk density range of 108.7- 109.5 lb. / cu. ft., some results were obtained at a bulk density range of 101-102 lb. / cu. ft. Analysis of varance tables have been drawn up from the results obtained from least squares correlations and significance tests applied. It was concluded that oil content and temperature were significant variables for the degree of shear strength developed by the oil sand; increase of oil content and decrease of temperature each cause an increase in shear strength. The bulk density range 108.7 to 109.5 lb./cu. ft. gave angles of shearing resistance from 30° to 40° and initial resistance values of 0.37 p.s.i. to 0.85 p.s.i. For the bulk density range 101 to 102 lb. / cu. ft., lower values of shear strength were obtained, indicating that compaction density was also of importance

Jan 1, 1960

By Edward P. Barrett

Iron ore, when subjected to reducing gases at a temperature suitable for reduction of the oxide but not high enough to melt the ore or metal formed, is converted into metallic iron. The product, being the original piece of iron oxide minus its oxygen, is sponge-like in appearance when viewed under a magnifying glass, and hence is called 'sponge iron. Sponge iron was probably the form in which some of the first iron was recovered from the ores. As early as the eighth century the Catlan forge developed into a low shaft furnace known as the high bloomary, in which iron was produced in the form of a pasty mass. These furnaces were increased in height, and with increased temperatures came the production of liquid cast-iron, at first undesirable because of lack of knowledge of methods for working it. In 1340 the first true blast-furnace was built iri Belgium. Some castings were made, but the greater part of the iron was converted into wroughtiron blooms by a crude puddling process. Charcoal was the universal fuel until the latter part of the seventeenth century, when coke was first used in England. Larger scale developments of methods of refining pig-iron followed. In I 885 Bessemer built his first converter in England, and within a few years the Siemen' s regenerative open-hearth furnace was developed, also in England, to produce steel. Then followed the enormous expansion in the metallurgy of iron. The idea of a direct process for the production of iron and steel has persisted during all of this time.

Jan 1, 1925

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By W. Torres Pino, L. Mariscal Samaniego

The Ilo Smelter has been continuously operating since 1960 with Reverberatory furnaces and Pierce Smith converters producing blister copper. The original installed capacity of 1.134 tons per day of concentrated was expanded in 1976. A process of modernization started in 1995 and 1998 with the installation of an El Teniente Converter, a sulfuric acid plant and an oxygen plant to reduce the gaseous emissions to the atmosphere. With the official approval of the Environmental Compliance and Management Program (Programa de Adecuaci6n y Manejo Ambiental - PAMA) in January 1997, Southern Peru Copper Corporation made a commitment to capture 91. 7% of the S02 generated at the smelter by January 2007. After an evaluation of six different technologies, the ISASMEL T process was selected because it can be easily adapted to the present operation, has a lower capital cost and it is a simple process. The fast learning curve to reach the total capacity will allow to fulfill the PAMA commitment in time. The project construction is in process and SPCC is prepared for a successful start-up and transition of the current operations at the end of year 2006. This paper outlines the factors considered by SPCC in its choice of ISASMEL T technology and describes the construction and the start-up activities of the new facilities.

Jan 1, 2007

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By Earl Gebhardt

The planning and design of mining panels in the Potash Corporation of Saskatchewan Inc., Lanigan Division mine Block B involved a number of investigative techniques. The techniques utilized to gain insight into the viability of mining included 2-D and 3-D seismic surveys, longhole drilling, exploration wells, photolineament, magnetic and gravity surveys, and actual room excavation.

Feb 1, 1993

By T. Prietl

Metallurgical vessel linings are multilayered, consisting of refractory bodies, insulation materials, joints, and additional space to control for thermal expansion. A unique biaxial hot testing press (BHTP) was installed at the RHI Refractories Technology Center Leoben, Austria to enable the three-dimensional behaviour of complex vessel lining segments to be investigated under simulated service conditions. Using the BHTP, the heat up and thermo-mechanical behaviour of magnesia chromite brick lining segments with and without mortar filled joints were examined. The results obtained during the initial heat up provided validation of CFD modelling of the lining system. In addition, after the heat up and under steady state conditions, the lining behaviour during deformation-controlled compression and relaxation was examined. These analyses generated important data regarding the stiffness, joint compressibility, and brick damage of the lining segments after cyclic loading and unloading as well as the benefits of using mortar joints in the lining. These investigations were performed in collaboration with the Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals, University of Leoben, Austria. The BHTP has been operational since November 2004 and is providing information regarding the thermo-mechanical behaviour of different lining segments.

Jan 1, 2007

By C. R. Edwards

"Since the first commercial extraction of uranium in the early 1940s, the range of feasible process alternatives has greatly increased. This paper reviews process options to reduce extraction costs, improve efficiencies, effect safer operations, and lessen environmental impacts. Equipment and processes used in the past, in use now, and that could be considered for future use are described.BackgroundTwo billion years ago life on earth consisted solely of single celled creatures of the simplest design (Gould 1989). Incredible as it may seem, uranium fission reactors were operating then also. In what is now western Africa, a series of natural reactors were fueled by rich uranium deposits in contact with underground rivers. Water from the rivers provided the moderator necessary to sustain the nuclear fission chain reaction. These primordial reactors ran down after about 600 000 years (Ontario Hydro 1989).Because it is ubiquitous in the earth's crust, humans have always been in contact with uranium. Mining of uranium, albeit not intentional, is ancient ; uranium minerals were embedded in ore veins mined for metals such as silver and copper.Uranium was discovered in 1789 in Berlin by an apothecary, Martin Heinrich Klaproth, who named the element after the recently discovered planet Uranus. The metallic element uranium, as opposed to its compounds, was extracted in 1841 by the French chemist Eugene-Melchior Peligot. The atomic mass of uranium was calculated to be 120, but the Russian genius Dmitri Ivanovich Mendeleev (famous and welcome everywhere except in Russia, where his liberal politics were detested by the Tsar), found this did not fit into his periodic table, and submitted a value of 240. Mendeleev was close; the exact atomic mass is 238.029.Henri Becquerel's detection of the radioactivity of uranium in 1896excited scientific study of the metal, but virtually no practical use was found for uranium outside of a minimal consumption as a colouring agent for glass and ceramics. Scientific interest intensified in the 19305. In 1933 Leo Szilard patented the concept of the nuclear chain reaction. While walking to work on a fine fall London morning and mulling over the problem of how to release atomic energy, he was stopped by a red light. He stood in thought and conceived the notion of the neutron-activated chain reaction before the light turned green. The patent was filed in 1934, and Szilard assigned it to the British Admiralty in order to keep it secret, in an honourable but ultimately futile effort to prevent the misuse of science (Bronowski 1973)."

Jan 1, 1992