Search Documents

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company's mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By A. Demers, M. Chapman, N. Reynier, R. Lastra, M. Courchesne, C. Laviolette

Historic medical isotope production at Canadian Nuclear Laboratories (CNL) in Chalk River involved the dissolution of irradiated isotope targets prior to extraction of Mo-99. This process generated liquid waste that was cemented in 5-gallon containers and transferred to an outdoor waste-management facility for intermediate storage. Research was undertaken to develop an innovative method for uranium, mercury and cesium recovery from the radioactive cemented waste (RCW). Regulations prohibit the removal of active radioactive waste from the Chalk River facility. Thus, CanmetMINING produced surrogate material following the same procedures and conditions to those used at CNL. The selective recovery of the uranium from the surrogate radioactive cemented waste (SRCW) could offer CNL more disposition options for the resulting wastes. Leaching tests were performed using four different SRCW at 1 kg scale. Different conditions, operating parameters, and the presence of plastic and corrosion products were evaluated on solubilization. The research investigated the use of potassium iodide with the sulphuric acid leach to increase metals recovery. Iodine improves the solubilisation of metals and the U dissolution reached 99%. The increase of leaching time reduces the U solubilization due to silica gel formation. Therefore, it will be important to control leaching time to avoid the loss of U during the pilot scale experiments. For Hg, the solubilization ranged from 60 to 80% due to the presence of metallic mercury and mercury sulphide found in SRCW cured at 60°C and/or aged for 30 months. Ion exchange (IX) was found the best method to separate the uranium from the impurities and produce a purified and concentrated uranium solution suitable for yielding a uranium product (yellow cake).

Jan 1, 2020

By József L. Margitfalvi

Different Au/MgO catalysts modified with Mn, and Fe were prepared by precipitation-deposition. The catalysts were characterized by XRD, FTIR, Temperature Programmed Reduction (TPR) and CO chemisorption and were tested in CO oxidation in the temperature range of 243-523 K. The catalytic tests using both Temperature Programmed Oxidation (TPO) technique and time on stream (TOS) experiments revealed the high activity of catalysts prepared. In TPO experiments the modification by Mn significantly increased the activity above 300 K, however in the subambient temperature range the activity decreased considerably. Catalysts modified by iron did not show any decrease in the activity below 300 K, while the activity at high temperature increased significantly. Catalysts modified by Mn, Fe showed higher activity, selectivity and stability in preferential CO oxidation, carried out in the presence of hydrogen than the unmodified Au/MgO catalysts. Results of in situ FTIR spectroscopy on both the base Au/MgO and the iron modified catalyst unambiguously revealed the formation of ionic gold in the presence of CO/O2 mixture. The formation of this species was strongly hindered in catalyst modified by manganese. Results obtained strongly support the need for the formation of "metal ion - metal nanocluster" ensemble sites. These sites are involved in the activation of the CO molecule prior to its reaction with atomic oxygen. It is suggested that at subambient temperature these ensemble sites contain mainly ionic forms of gold, while at higher temperature iron or manganese ions are involved in CO activation.

Oct 1, 2003

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By J. Elderton

"The combination of A C induction motor and flu id coupling, of either the fixed or variable filling type, constitutes a simple, low cost, highly reliable drive unit, with many applications in the mining field.The paper will, however, concentrate on the variable filling fluid coupling in three principal applications-conveyor starting, infinitely variable speed control for slurry and slimes pumping and dewatering pumps for deep mines. Fluid couplings can be used with standard or custom-built control gear equipment, ranging from the most simple, time-based open loop types, to those having the latest microprocessor techniques.IntroductionThe first industrial applications of fluid couplings included their use in the mining field as hydraulic slip regulators for flywheel generating sets. These installations, usually rated at around 1700 to 2500 hp, were located at mine shafts where the electrical grid transmission lines were not strong enough to cater for the peak power demands of the cage winding cycle. In Canada, the first two significant examples of variable filling fluid couplings for mining were on conveyor drives, at Steep Rock Mines Limited, closely followed by the major iron ore handling term inal on the St. Lawrence River at Sept-Iles. Successful and reliable operat ion of the fluid couplings at these two sites set the pattern for use on many subsequent mining projects throughout the Canadian Continent."

Jan 1, 1986

By W. B. Boggs

A paper describing the Noranda smelter was presented at the 1930 annual meeting of the Institute (1). A lacer article appeared in the Trans-actions of the A.I.M.&M.E. in 1933. Since that time there have been many changes and improvements in plant operation and it is the abject of this paper to give an account of developments up to the beginning of 1939. The Noranda smelter was built originally for a capacity of 30,000 tons a month. At present, the average tonnage being treated is 110,000 tons a month, the tonnage of custom ores alone amounting to almost the total rated capacity of the original plant. This increase has been accomplished by increasing the capacity of the reverberatory furnaces from 700 tons of solid charge per furnace day in 1928 to 1,500 tons per day at the present time. In 1935, it appeared chat the limit of furnace capacity had been reached at about 1,300 tons of charge per day because of the short life of the sprung silica arches. However, the adoption of the suspended magnesite roof, which had been developed at the Flin Flou smelter of the Hudson Bay Mining and Smelting Company, overcame this difficulty and it is believed that the limit of the capacity of the present reverberarory furnaces has not been reached. A brief account of the changes to equipment in the various departments will be given, followed by a description of the more important features of present smelter practice.

Jan 1, 1939

By A. Ojaghi, A. R. Mohammadi

"The Marvast monazite deposit is located 35 kilometres south - southwest of Marvast in Yazd province of Iran. A representative sample weighing approximately 10 tons was prepared to study the amenability of the ore to physical beneficiation. The size fraction of +1000 µm was removed due to low monazite content and the –1000 µm size fraction was concentrated by the gravity-classification-magnetic methods. According to the results of sample characterization, the representative sample contains 220 ppm REO that is contained in monazite. It was concentrated to 41.5% REO by the above mentioned methods. The recovery of REO in the monazite concentrate was 41.5%.INTRODUCTIONRare earth elements are critical metals in many countries (Gupta, 2005; UK Geological Survey, 2011). Increasing application of these metals in hi-tech industries and price fluctuation caused by Chinese production policy has led other countries to focus on their local resources (UK Geological Survey, 2011). In this case, Iran is not an exception.REE mineralization in Iran is mainly located in the central zone. Regarding the exploration data, these deposits are divided into two categories. The first group is iron ore deposits in which the REE are carried by phosphate minerals. The other group is placer deposits where monazite is the major mineral of the deposit. The Marvast placer deposit is one of these types of deposit (Daliran, 1990; Mokhtari, 2008; Torab, &Lehmann, 2007; Alipour, 2014)."

Jan 1, 2016

By J. Desrosiers

"Minnova Inc. has five operating divisions thoughout Canada. One of them is Lac Dufault which was established in 1964.Lac Dufault is located 15 km north of Rouyn-Noranda, in what is known as Noranda volcanic centre, in northwestern Quebec. For more than 25 years, Lac Dufault has produced copper, zinc, gold and silver from four different mines: Norbec, Millenbach, Corbet and now Ansil.Ansil, officially in production since July 1989, is one of the deepest mines presently in production in Quebec. This high-grade copper, gold, zinc and silver orebody is being mined at a rate of 1200 tonnes per day with a total workforce of 200 employees.Of particular interest are the high mechanization level of the underground mine, technical innovations also underground, and computer applications throughout the division.IntroductionMinnova Inc. was formerly known as Corporation Falconbridge Copper until 50% of its shares were bought by Kerr Addison Mines Ltd . in 1986 and it became a member of Noranda Group of Companies.Minnova stands for mining innovation. It means Minnovaaims to use state-of-the-art technologies in mining and exploration to achieve maximum efficiency and cost effectiveness. It also means that they aim to use both proven and innovative management principles to the optimum benefit of their employees and shareholders. Minnova has operations across Canada. Presently four mining divisions produce copper, zinc, gold, silver and lead. Two are situated in Quebec: Lac Dufault (established in 1964) and Lac Shortt (established in 1985); one in Ontario; Winston Lake (established in 1988); and one in British Columbia; Samatosum (established in 1989).Minnova has an annual exploration budget of $15 million divided 60/40 between base metals and precious metals. Most of Minnova's exploration efforts are concentrated around their existing mines. Exploration is carried out from six regional offices located at Rouyn-Noranda and Chapais in Quebec; Thunder Bay in Ontario, Vancouver in British Columbia, Reno, Nevada in the United State and Panama City Panama. Each of the Canadian offices maintains close liaison with nearby operations.Lac Dufault Division is located in the Noranda mining camp, approximately 15 km north of the city of Rouyn-Noranda, in northwestern Quebec (Fig . 1)."

Jan 1, 1991

By S. Hunt, S. Jayasekera, J. Kyle, N. Perera, K. Stone

A preliminary investigation has been conducted to determine the conditions for the precipitation of phosphate from the liquor produced after a hydrochloric acid pre-leach and rare-earth recovery from a rare earth containing fluorapatite concentrate from the Nolans rare earth deposit in the Northern Territory of Australia. The results show that at 50oC the phosphate can be precipitated in two stages using limestone to produce a Stage 1 precipitate containing most of the impurities including iron (94%), aluminium (92%), fluoride (98%), uranium (84%) and thorium (94%), followed by a relatively pure Stage 2 dicalcium phosphate precipitate (DCP) containing only 0.05% Fe, 0.05% Al, 0.1% F, 0.01% U, and <0.01% Th. The initial Stage 1 precipitate contained about 25% of the phosphate while the remaining 75% reported to the Stage 2 phosphate precipitate. Depending on the required radioactivity specifications, the amount of phosphate in the Stage 1 precipitate could be reduced. Reagent requirements were 11.4 kg limestone (as pure CaCO3) per cubic metre of solution for the Stage 1 precipitate and 39.7 kg limestone (as pure CaCO3) per cubic metre for Stage 2. The analysis of radionuclide balance indicated that radionuclides deported mainly to the final filtrate (86.4%) compared to Stage 1 precipitate (5.4%) and Stage 2 precipitate (8.2%). Settling and pressure filtration tests indicated the precipitates were both readily settled and filtered. The final moisture contents of the Stage 1 and Stage 2 precipitates were 62.5% and 49.3%, respectively.

Jan 1, 2014

By A. Broussaud

The paper describes the advanced grinding control system implemented at Newmont Ahafo gold mine, Ghana in 2009 and 2010. It shows how the different components of the Advanced Process Control (APC) system cooperate for increasing plant performance. The SABC circuit processes hard rock from different pits mixed with a variable proportion of oxides. The control strategy is designed to address specific disturbances, including start/stops of pebble crushers, unavailability of oxides, changes in rock size distribution resulting from segregation in the stockpile, and changes in ore type and hardness. The system consists of an expert system per se with extensive use of fuzzy logic, supplemented by an online dynamic model of the process used as a soft sensor, a VisioRock? rock size measurement system over SAG mill feed before addition of recycled pebbles, and an AudioMill? system to analyze the SAG mill sound and detect impacts on liners. All these components are embedded in the same OCS© software platform, which, among other benefits, makes it easy to support the entire system remotely. The paper details the physical constraints and the variables that are manipulated. It describes the control strategy and the contribution of each component of the system. It also describes the project implementation and the performance of the system. In addition to a strong involvement and support of management, the very good acceptance of the operators has been facilitated by the remote access system that made it possible to immediately modify the system each time it was needed during the baby sitting phase. The system made it possible to increase gold production significantly through increases in tonnage and recovery thanks to a better control of the grind size through a stabilization of the secondary ball milling circuit and an improvement of the operating conditions of the classifying cyclones.

Jan 1, 2012

By C. Horstmann, D. Andreo, G. Barthold

"The concept of large single line grinding circuits provides a valid answer in project feasibility studies by reducing capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational aspects, in terms of higher and greater process stability, and reduced operational costs mainly due to the associated lower maintenance expenditures. However, concerns exist in the minerals industry on whether large single line grinding could reduce the overall concentrator plant availability. The mechanical design and integrity, the mill and gearless mill drive integration, as well as assets management aspects of this type of equipment are the key to guarantee successful availability records. Together with an overview of the added value provided by large single line grinding circuits, this paper focuses on risk mitigation strategies during mill and gearless mill drive integration, as well as on the design of the equipment itself, for the key aspects which could put at risk the operations availability.INTRODUCTIONDespite a large long term demand for commodities, the mining industry has never faced complex challenges as it is doing today. Decreasing high-quality and accessible deposits, declining ore grades in existing mines, shortages of electrical energy (e.g. in Chile) and an aging workforce are the most significant among the megatrends affecting our industry. In addition to this, flat underlying commodity prices and high price volatility are currently posing strong requirements to miners when entering into the process of approving investments.Nowadays to get projects financially approved (optimizations, expansions, new plants), capital expenditure has to be reduced, as observed up to 30% compared to the last decade, and at the same time the plant design has to be such to demonstrate that operating costs will also be significantly lower than in the past.When it comes to the concentrator plant, the concept of large single line grinding circuits provides a valid answer in project feasibility studies by significantly reducing the capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational costs, in terms of higher and greater process stability and reduced maintenance expenditures."

Jan 1, 2016

By R. S. Bigelow

Part 1.- Metal Mines Early experiments with mechanical loaders in metal mines were confined largely to machines of the shovelling type and generally air-operated. Although the first application of the scraper to metal mines dates back to 1910, it was not until about twelve years ago that it came to be used extensively. Generally, the scraper gives better results in metal mines than in coal mines, as degradation due to soft bottom and breakage are not factors, but it has a wide range of application and is successfully used in the mining of salt, potash, gypsum, zinc, copper, and a variety of ores, from soft material to hard chunky ore which settles compactly. Today, the scraper has replaced to a large extent the shovelling type of machine in metal mines. Scrapers have offered an inexpensive solution for the mucking problem and are now employed in most mining districts throughout the world. They are operated by labourers of all colours and degrees of skill. Each installation, however, requires individual study on the part of the mine mechanical department to determine the type of scraper, horsepower of hoist, and most economical speed of rope, as well as method of rope rigging. Unfortunately, the scraper has no power to select pay ore from waste and its suitability for use under circumstances which might require sorting of the ore can only be decided by a weighing of the economic factors involved

Jan 1, 1931

By E. Wraith, W. W. Culver, B. Wesstrom, P. J. Mackey

Electrodeposited copper of the 1860s was of unprecedented purity, although the profound significance of this achievement was not fully realised until the dawn of the electrical age a decade or so later. By the 1870s there were three somewhat large (4 to 4.5 tonnes Cu/day) electrolytic copper refineries in Germany based on J. B. Elkington’s process, first patented in the United Kingdom in 1865. More such refineries were planned throughout Europe. At the same time, copper output in the U.S.A. was starting to expand and with the spread of European electrolytic copper refining technology across the Atlantic, the door opened to major increases in North American output. The technology was first taken up in 1879 by James Douglas at the Chemical Copper Company in Phoenixville, Pennsylvania, where he was Superintendent. Douglas was assisted in this pioneering work by Edward Weston. The copper refinery at the Chemical Copper Company was small, not unlike the first plants in Europe. The present authors contend that the electrolytic copper refinery at the Chemical Copper should be regarded as the first copper refinery in the United States. The Balbach Copper Refinery in New Jersey, which commenced operations in 1883 with an initial production of about 2 tonnes Cu/day, has been erroneously considered as the “first commercial refinery”; it rightly belongs in second place. The early developments at these plants are discussed in this paper. INTRODUCTION In the mid-1800s, the main uses for copper were as sheathing on the wooden sailing ships of the day to protect from marine growth, boiler components in locomotives and steam engines, along with some construction uses. Copper ores were generally smelted, and further fire-refined for market. The recovery of gold and silver, if present in payable amounts, was a slow and relatively expensive step. This situation regarding copper would change by the 1870s with advances in the generation and use of electricity. The introduction of the dynamo led to major developments in electrorefining. First demonstrated in principle by Faraday in 1831 (Faraday, 1832), the dynamo was subsequently adapted and further developed by J.S. Woolrich for electro-metallurgical applications in 1842 (Woolrich, 1842; Napier, 1845). It provided a new source of power with the unprecedented potential to significantly change the scale of metal production by electrometallurgy. Interestingly enough, copper would be needed for the electrical age just beginning. By 1869, advances in dynamo design offered relatively reliable large machines, which enabled J. B. Elkington in the United Kingdom to use the dynamo in the radically new Pembrey copper electrorefinery — the first copper electrorefinery in the world (Wraith, 2013). Initial production at Pembrey was small — in the range of 1 to 2 tonnes/day — while gold and silver were recovered more readily by the treatment of the slimes than with methods used hitherto.

Jan 1, 2019

By Leroy C. Stewart

Owing mainly to the use of ethylene dibromide in the production of tetraethyl lead for gasoline treatment, there has been a tremendous increase during the past decade in the demand for bromine. In the United States, production, derived mainly as a by-product from the treatment of brines from salt wells, rose steadily from about two million pounds in 1924 to nine million pounds in 1931. In 1936, production amounted to between 20 and 21 million pounds. Much of the increase during the past four or five years has been due to the operation of the Ethyl-Dow Chemical Company&apos;s plant, which extracts bromine directly from sea water. The process employed by the Ethyl-Dow Company is somewhat similar to that in use on salt-well brines at their plant at Midland, Michigan, but whereas these brines contain around 1,300 parts per million bromine, sea water contains only 65 to 70 p.p.m.-about as much as the waste effluent in the brine process. By intensive research, however, a process was developed whereby a very considerable percentage of the bromine content of sea water could be recovered, and at a satisfactory operating cost. In its essentials, the process consists in liberating the bromine from the sea water by treat-ment with chlorine, blowing the bromine out of the water by a current of air, and finally absorbing it in a solution of soda-ash.

Jan 1, 1938

By Osvaldo A. Bascur, Curt Heftier

The lack of integrated information including the Energy/Utility Suppliers with sufficient detail for analysis causes inefficient operation in metallurgical complexes including the Energy/Utility Suppliers . Defining the right context for information use is essential for sustainable operations. This being said, what are we doing to enable people to act upon information and to be aligned to optimize the use of resources like raw materials, energy, water and consumables for an entire metallurgical complex? Collaboration between all company entities is a key component of improving efficiency. Evolution of web technology and object modeling of enterprise assets enables collaboration across the whole business. Operational troubleshooting occurs more quickly as the organization acts on issues to reduce wasteful operation. This paper presents a real time software infrastructure with tools that give users the ability to sift through available data, transform data into information for business continuous improvement and optimization. We will introduce a new technology for analyzing real time data, information and events using multidimensional analysis of information to detect anomalies based on the statistics of the data classified by time events to reduce the information into action. A new paradigm for collaboration at a local and strategic level is proposed to enable the enterprise to become proactive in dealing with wasted time and products. Three examples from the industry will presented and their benefits highlighted.

Jan 1, 2011

By R. A. Wyman

A comparison of the amount of minus-28-mesh product produced by a standard grinding test procedure is provided for 45 non-metallic materials. The percentage of product, the weight of product per unit of energy used and the weight of product per mill revolution are shown. The results exhibited excellent reproducibility and demonstrated an accurate comparison of grindability for non-metallic materials.

Jan 1, 1977

By G. S. Ospanova

The results of complex processing sulphide copper ore and advantages of recovery of copper by vat and heap leaching, sorption, cementation and electrolytic solutions processing and utilization of waste material after heap leaching of copper for production of building materials were investigated. The combined chemical solvents with the additives of oxidizing agents are developed at the KazNTU. The solvents are inorganic or organic chemical reagents, which form complexes of Cu, Au, Ag, Pt, Ni, Sr, Co etc. Recovery of non-ferrous metals from solutions and purification of industrial waste waters is carried out on the base of using new synthetic and natural sorbents (from local raw materials) which are able to bind ions in both cationic and anionic forms depending on type of ligands and external conditions. Optimum parameters of copper sorption were determined. The developed wasteless technologies of copper extraction from sulphide ores with usage of new non-toxic solvents and accessible sorbents with full recycling of water are tested in pilot scale heap leaching, and are recommended as the ecological, economical and practical alternative to traditional methods.

Jan 1, 2007

By K. B. Young

Possibly the most complex fatigue problem associated with the development of the axial-flow &apos;gas turbine is discussed in its broader aspects from the metallurgical viewpoint. Reference is made to nodal patterns, interference diagrams, etc. The use of such data in analysis of a turbine :blade failure is illustrated. Special attention is given to the influence of some metallurgical variables affecting fatigue strength and, in particular, heat treatment is shown to have a pronounced effect on .the relative fatigue and creep strength properties of a nickel-chromium-cobalt base alloy suitable for turbine blade applications.

Jan 1, 1958

By C. H. Knight

"THE OBSERVATIONS that follow are confined to simple wet cyclones such as the cylindro-conical unit developed by the Dutch States Mines and marketed in America under the trademark 'Dorr-Clone'. Energy to do the work comes from the inlet velocity of the feed slurry, which is usually pumped' to the unit by a centrifugal pump.Such cyclones are simply classifiers of enormous capacity and depend for their separating effect on differences in rates of particle settlement. These particle settling rates, of course, vary with particle size, particle density, particle shape, pulp viscosity, and pulp density.The dilution of the overflow product affects both pulp viscosity and pulp density. In most operations, the temperature and the composition of the liquid -hence its viscosity --are fixed, but both pulp viscosity and pulp density can be changed by changing pulp dilution.Since the separating effect depends on differences in rates of particle setting, a perfect split with 100 per cent of the particles coarser than a given size in the underflow and 100 per cent of the finer sizes in the overflow is not possible. Just how far the separation departs from this perfection can be calculated rather exactly from the following principles, which also apply to mechanical classifiers. In removing or settling out of the overflow product all particles up to a specified size, some of the finer particles must settle out simultaneously."

Jan 1, 1955