Search Documents

By Peter Metcalfe

"Wireless communication in the mineral processing environment is not as simple as it is in the home or office environment. The correct design of a wireless network in the mineral processing environment can offer a more flexible and lower cost installation than the transitional fiber networks. However with the flexibility of a wireless solution, also comes some limitations. By reviewing the plant requirements along with weighting the wireless benefits and limitations it is possible to design a network that combines the robustness of a wired solution with the mobility of a wireless solution. This paper addresses some wireless design considerations and it looks at some real life examples in the following areas: •,Meshed wireless network for high levels of redundancy •,Wireless instruments (such as HART, Modbus and others) •,Portable devices for mobile operators •,Network monitoring for plant personnel (it’s no longer just for IT people) INTRODUCTION Typical networks used in the mineral processing environment consist of a fiber network infrastructure with industrial switches used to connect the network devices. These fiber networks can be redundant or put into a ring topologies to offer a higher level of availability. Fiber networks have the benefits of: •,Immunity to noise from power and grounding issues •,Ability to span long distances (2km for multimode fiber and 20km for single mode fiber) •,Maintainable “off-the-shelf” technology Fiber networks however have some drawbacks, such as: •,Relativity high initial installation cost for cable trays, poles, trenches and pulling and termination of cable. •,Fixed geographic topology, adding future fiber drops may be challenging and expensive. •,Mobile users are not considered. Integrating a wireless network with a fiber network can offer the best of two worlds, a reliable high speed backbone for mission critical activities and a wireless network for remote applications and mobile users."

Jan 1, 2014

By C. J. Allen, L. Battiston

"Introduction It has long been recognized by the hot-dip galvanizing industry that the characteristics of the galvanized coating can be influenced significantly by steel and pro cessing variables. Probably the variable of most concern to galvan izers today is steel chemistry. More specifically, the problem is the excessive reactivity of continuously-cast, silicon-bearing steels. In the past, structural steels processed by general galvanizers were in the low-to-medium ca rbon category and contained silicon at either low impurity levels (as with rimmed steels), or less than approximately 0.10% (as with semi-killed steels). The structures of the coatings produced on such steels are characterized by dense, compact layers of delta and zeta iron-zinc alloy phases and a distinct outer layer of eta zinc, which usually imparts a bright shiny appearance to the coating. The presence of silicon in steel, above the so-called semi-killed levels, is known to cause marked stru ctural changes in galvanized coatings. Such coatings are characterized by a relatively thin delta layer, a thick , coarse zeta layer and frequently an absence of the eta layer. The eta phase, comprising zinc which is carried out of the bath during withdrawal of the work, can be consumed by the continuation of the coating reactions until its temperature drops to the solidification point. This results in a dull grey and often mottled surface instead of the usually bright metallic appearance. These galvanized coatings are usually much thicker than coating specifications requ ire and they are usually more brittle and have poor adhesion to the steel. In service, these coatings tend to develop a rust-like discolouration. With the wider use of continuous casting by the steel producers and the associated additions of silicon in this process, the problem is becoming more important and receiving greater attention from the galvanizing industry ."

Jan 1, 1987

By L. M. Lowe, D. G. Feasby, J. R. Goode

"Rare earth resources usually contain minor amounts of radioactive elements. The most widely recognised sources of radioactivity are associated with thorium and uranium. However, also present in the resources are isotopes of rare earth elements (REE) that are themselves radioactive, including lanthanum (La-138), lutetium (Lu-176) and samarium (Sm-147). These radioisotopes, as well as remnants of the natural thorium (Th-232) and uranium (U-238, U-235) decay series, can contribute to significant levels of radioactivity in mixed REE concentrates and in separated products. Levels such as these can present challenges for transport, transboundary movement, product storage, workers’ health and safety, as well as waste management issues at the facilities that separate out the individual REE’s. These are discussed in this paper. A particularly challenging radioactive isotope is Ac-227 (a decay product in the U-235 decay series). Actinium behaves chemically similar to lanthanides and hence normally concentrates with REE multi-element composites. Reliable analysis of Ac-227 is not widely available and the methodology required to deal with this challenge is briefly described. A principle reason for minimization of radioactive content throughout REE processing is restrictive specifications by concentrate purchasers in order to reduce waste management challenges. Approaches to the minimization of radioisotope content in REE concentrates and separated products are outlined in this paper."

Jan 1, 2014

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004

By Bali. D. D., S. Chattopadhyay

"The planning and construction of prime coking coal beneficiation plants in the nationalized mines in India are reviewed. Flow schemes, construction practice, materials consumption, and costs are detailed.Medium-capacity beneficiation plants with multiple loops are recommended under Indian conditions.IntroductionThe reserve of high-grade and easily washed metallurgical coal in India are quite limited. Prime coking coal constitutes approximately 22% of the total resources and occurs exclusively in the Jharia coalfield in the state of Bihar. Bharat Coking Coal Limited (a subsidiary of Coal India Limited (CIL) the nationalized mining sector of India) owns 80% of the Jharia collieries. The development of Jharia coalfield in the pre-nationalized period before 1971 has been characterized by a large number of small mines with primitive mining methods and low productivity. The production of prime coking coal to meet the demand of the steel industry in India has to increase from the existing level of 11.1 million tonnes to 43.4 million tonnes per annum by 2000 AD, thereby producing 5.61 million tonnes and 22.7 million tonnes of clean coal respectively. An ambitious program has been undertaken for development of bigger mines with an average production of 1 to 3 million tonnes per annum. With the fast dwindling reserves of good quality coking coal, more inferior grade coal seams, having difficult washing characteristics, are now being mined. All the coal from the future mines will have to be beneficiated to make it suitable for consumption of steel plants; the following washeries are being planned for construction by 2000 AD:"

Jan 1, 1986

By Pierre Pelletier, Julie Fournier, Gianni Bartolacci, Yves Breau, Dominique Girard, Ahmed Bouajila, Carl Duchesne

"The development of on-stream analyzers (OSA), such as those based on X-ray fluorescence (XRF), has been key to improve metallurgical performance of flotation processes. However, since these analyzers are shared between several streams, they typically provide grade measurements every about 10-15 minutes. In general, this frequency is too long compared to process dynamics and so, implementing an efficient feedback control strategy based on OSA can be difficult. In addition, due to the limited capacity of OSA systems, several important intermediate streams are not analysed, but could provide relevant information about the state of a flotation circuit.To overcome this problem, vision systems have been developed in the past to predict concentrate grade based on froth color – this could be very useful to control flotation performance between OSA measurements. However, applications reported in the literature typically use univariate summary statistics of the full red, blue, and green color distribution of froth images, while RGB images are truly multivariate. Although, in some cases, grade prediction was achieved with reasonable accuracy, one may, by using only summary statistics, miss important information about the state of the flotation process.This paper investigates the application of Multivariate Image Analysis (MIA) concepts to flotation froth images. These techniques are based on multivariate statistical methods such as PCA and PLS, which have the ability to analyze large databases (such as digital images) and summarize the relevant information content of the data into a small number of latent variables, capturing the most important features of the images for concentrate grade prediction. The potential of application of these methods in the mineral processing industry is illustrated using a few industrial case studies."

Jan 1, 2003

By R. B. Barlow, J. A. C. Fortescue

Originally developed for use in mineral exploration, regional geochemical mapping based on stream (and lake) sediment sampling is showing broader application in other areas of the earth sciences and in environmental science. The purpose of this paper is to focus attention on the role of regional geochemical mapping in relation to geological and environmental studies. This is achieved using a descriptive equation for the chemical composition of a stream-sediment sample and then relating it to the use of successive approximations in geochemical and environmental investigations. The procedure is further qualified with reference to time and process in the formation of regional geochemical patterns. Examples are included of studies based on stream sediments related to bedrock geology, surficial geology, ecology and man's effect on the geochemistry of the environment. The range of applications of regional geochemical mapping in earth and environmental studies is outlined and some conclusions drawn regarding the future development of geochemical mapping under Canadian conditions.

Jan 1, 1980

By Manuel Sanchez, Marcial Medina, Matt Hurley, Hugo Granados, Pramod Kumar, Raj Rajamani, Jose A. Delgadillo

"Large-diameter ball mills have traditionally used steel liners—steel being a highly durable material that can be shaped into any desired geometry, among which the double-wave has been the preferred design. Such a design produces a purely cascading charge motion, which is ideal for the shearing action needed to produce a finer product. Today, however, rubber liners, which have been in existence for over forty years, are now preferred over traditional steel, largely because they weigh less and are easier to maintain. In this paper, we show the operating data from the Hudbay Minerals’ Constancia Mine, wherein the liners on a 26-by-40-foot mill were changed from conventional steel liners to PolyStl™ liners. It is then shown that this change reduced the amount of energy consumed whilst being able to maintain previous grind and throughput levels. The design is verified via discrete element simulations.IntroductionThe Constancia Mine (“Our Business: Peru,” 2016) is located in the southeastern Andes of Peru, at an elevation of approximately 4,200 m. It can be accessed via the CU-126 road, about 95 km from the town of Espinar in Espinar Province. The mine also contains both the Constancia and Pampacancha deposits in the Province of Chumbivilcas. Hudbay Minerals, Inc. acquired the mine in 2011, through the purchase of Norsemont Mining, Inc. and currently retains sole ownership of the property. Production of the Constancia Mine began in 2014, with commercial production levels being achieved in April 2015.The Constancia and Pampacancha deposits primarily include hypogene, supergene, and skarn ores. The Mine’s main products, however, are copper concentrate, with silver contents, and molybdenum concentrate. These mineral reserves are expected to last approximately 22 years. Constancia’s open-pit mine supplies a processing plant that is designed for 81,900 metric tons per day of throughput. Average annual copper production is estimated to be 82,000 mT (contained metal in concentrate). Actual plant production can be found in Table 1."

Jan 1, 2017

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By D. J. Hutchinson, M. Lato, M. Diederichs

Light Detection and Ranging (LiDAR)-based applications for geomechanical purposes have recently proven to be a highly reliable and accurate form of remote analysis and documentation. The ability to remotely collect, process and evaluate rockmasses for structural geomechanical applications has benefits ranging from safety to efficiency, and provides a permanent record that can be assessed before and after an excavation has been completed. With the collaboration of Queen’s University and Rio Tinto, the Iron Ore Company of Canada (IOC) mines in Labrador City, Newfoundland and Labrador, evaluated the practical application of the I-Site 4400 LiDAR equipment, in conjunction with the Vulcan geotechnical module for geomechanical purposes. The project provided a comparative analysis between conventional hand-mapping and digital analysis. The analysis indicates that digital mapping could be employed as an active tool within the general geotechnical workflow, where results would be used in pit wall and rockmass support designs. As well, the field work enabled the generation of effective operational guidelines and protocols to maximize scanning efficiency.

Jan 1, 2009

By S. K. Schwartz

"This paper describes the general layout of the environmental monitoring scheme at Devco 's No. 26 Colliery, including wall face ventilation, fan performance and methane drainage, and then goes on to discuss the sensors, the outstation layout, the surf ace control room and the protection of the system.IntroductionCape Breton coal mines have been pioneers in the use of the latest technology in mining coal on this continent. To mention just one example, continuous methane monitoring at the coal face was started in 1976 and the idea of automatically stopping the face conveyor during high gas levels using the face signalling system was conceived and developed by CBDC engineers.With the introduction of remote environmental monitoring, No. 26 Colliery will be the first underground coal mine in Canada and possibly in North America to have computer-based comprehensive environmental monitoring.Traditionally, surveillance of the mine environment has been based mainly on periodic checks by portable or hand-held monitors. Although this method proved adequate, it has some limitations, namely:1) restricted 'number of observations and samples;2) relatively long time between taking measurements and availability of results for assessment.With remote monitoring, the above limitations are overcome because (a) monitoring is continuous and (b) monitored data are updated quickly (typically 5-7 sec.). Remote monitoring also provides a centralized 'information center' at the surface from where the entire mine environment can be monitored. Details of modes in which data can be displayed and features available at the location will be discussed later in the paper."

Jan 1, 1982

By Richard J. H. Barclay

The Lac Otelnuk iron property is located in the Province of Québec in the Northern Labrador Trough. The Labrador Trough is an extensive geosyncline of Proterozoic rocks, unconformably underlain by Archean gneisses. The Lac Otelnuk iron property hosts two significant magnetite iron-formation taconite deposits that outcrop, are sub-horizontal and are known to extend for at least 25 kilometres along strike. The host sedimentary rock package that includes a cherty iron formation is weakly metamorphosed to greenschist facies.

May 1, 2007

By Joseph Poplawski, Christian O’Keefe, Robert Maron

"Unique and difficult minerals processing measurement situations will be described and the application of passive array-based technology for performing these measurements will be illustrated. Examples of these situations include volume flow measurements in froth lines and flotation feed lines with entrained air, slurry lines with magnetite and other magnetic ore, slurry lines with abrasive or corrosive materials, high pressure lines, and slurry and non-slurry lines exhibiting scale buildup. Other situations include measurement of entrained air levels in pipes and in flotation columns. These measurements are achieved through CiDRA’s patented passive sonar array-based technology. This technology performs two independent measurements – flow rate and entrained air amounts. Two hardware implementations of this technology have resulted in a non-intrusive flow and entrained air meter which easily is installed on the outside of the pipe, and a submersible version for entrained air or gas holdup measurements which is used in flotation processes. Recent developments in extending this technology to solve other unique measurement problems such as valve movement confirmation will be covered.INTRODUCTIONThe minerals processing industry faces many unique and challenging process control conditions and environments. In terms of flow measurements, many of these situations are not being properly served by traditional flowmeters such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. A new class of flowmeters has been developed that solves these unique situations and flow measurement problems. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition. It does so accurately, reliably and without making contact with the fluid. These measurements are performed on practically any type of fluid within virtually any type of pipe.PRINCIPLE OF OPERATIONSonar array-based flowmeters are ideal for tracking and measuring the mean velocities of disturbances traveling in the axial direction of a pipe. These disturbances generally will convect with the flow, propagate in the pipe walls, or propagate in the fluid or slurry. First let us focus on the disturbances that convect with the flow. The disturbances that convect with the flow can be density variations, temperature variations or turbulent eddies. The overwhelming majority of industrial flows will have turbulent eddies convecting with the flow, thus providing an excellent means of measuring the flow rate as described below."

Jan 1, 2008

By Y. Nakamura, T. H. Okabe, S. A. Sunkar, K. Nose

Ruthenium (Ru) is known as a platinum group element with a very small production volume. In fact, the worldwide annual production of primary Ru metal is only about 20-30 tons, and it depends on the amount of Pt produced, since Ru is a byproduct from Pt smelting. The primary uses of Ru are as a material for resistors, as a catalyst for electrode materials, and as a sputtering target for hard disk memory storage. In order to recover Ru from the spent sand-blasting abrasive media generated during the cleaning of the apparatus used for Ru sputtering, a hydrometallurgical recovery process using hypochlorite solution has been investigated. In this study, various types of recycling processes that are presently under development are also introduced, and their features and differences are discussed. The advantages and disadvantages of the new recycling processes are evaluated, and the possibility of establishing new recycling processes in the future is discussed from a multilateral perspective.

Jan 1, 2014

By Erin Legault Seguin, Mike Rylatt, Curtis Mohns

"With energy costs increasing and ore grades diminishing, the role of pre-concentration in hard rock mining operations has been gaining greater interest. To maximize energy conservation, the pre-concentration process should be conducted at as coarse a crush size as possible while minimizing losses of pay metals. Dense medium separation (DMS) is a robust process that can be conducted at particle sizes as coarse as 300 mm and as fine as 500 µm with high separation efficiency, depending on liberation characteristics of the value minerals. The DMS process involves three steps: feed preparation, dense medium separation, and ferrous-based media recovery. This paper discusses each of these processing steps, but focus will be given to the dense medium separation stage. Various types of DMS equipment are reviewed. Pilot plant campaign case studies conducted at the SGS Lakefield site are presented, which have included a variety of mineral systems such as spodumene, sulphide-bearing gold ores, and complex sulphide ores. These case studies demonstrate that for amenable ores, mass rejection of 20-60% is possible while maintaining recoveries of greater than 90% in most cases.IntroductionPre-concentration is a process of rejecting mass of gangue while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Pre-concentration has been practiced in industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, typically requiring finer grind sizes and higher energy costs."

Jan 1, 2016

By P. Miranda, K. Le, G. Maes, R. Peters

"The Mount Milligan Mine, owned by Thompson Creek Metals Company Inc. (TCM), started operations in September of 2013. It is located between the communities of Fort St. James and Mackenzie and is the first major metal mine to open in British Columbia in 15 years. Based on reserves as of January 1, 2014, it has an estimated 22 year mine life with 2.1 billion pounds of copper and 6 million ounces of gold in reserves. Like all commissioning operations, there have been issues achieving design throughput and recovery due to flow sheet design, equipment failures, control philosophy, and reagent scheme. Efforts to improve overall mill performance include equipment modifications, reagent screening and testing, and grind size testing. Applying these changes to the mill and working closely with the mine has resulted in continuous improvement each month as Mount Milligan looks to achieve the nominal design capacity of 60,000 dry metric tonnes per day in the later part of 2015. Considerable focus is being placed into ensuring size reduction equipment is utilized effectively. Additional modifications and tests are being undertaken to steadily improve processes and alleviate restrictions in the mill. This paper will discuss the start-up and present ramp-up history of Mount Milligan, the current mill processes, and the steps taken to achieve expected production numbers.OPERATION BACKGROUNDMount Milligan is an open-pit copper and gold operation wholly owned and operated by Thompson Creek Metals. It is located approximately 155km northwest of Prince George, British Columbia, between the communities of Mackenzie and Fort St. James. The copper-gold porphyry deposit contains a Measured and Indicated Mineral Resource of 706.7 Mt at 0.18% Cu and 0.33 g/t Au, containing 2.84 billion lb. copper and 7.50 million oz. gold. Mine life is currently estimated at 22.1 years (“Feasibility Update – Mt. Milligan,” 2009). The mill is designed to process 60,000 dry metric tonnes per day and produce 400 dry metric tonnes of concentrate per day averaging 25.5% Cu and 40 ppm Au. Concentrate is delivered by truck and trailer to Mackenzie followed by rail to Vancouver for overseas shipping to various customers.Mount Milligan is considered a “zero discharge” operation meaning no process or surface water will be discharged to the environment. As well, stockpiling is very limited and is only permitted for a short period of time. This scenario presents several unique challenges. Scheduling of ore/waste production must be carefully planned as waste rock is used to build the tailings storage facility (TSF). Reagent selection is also important as persistent chemicals will have a tendency to build up in reclaim water which feeds the process water tank."

Jan 1, 2015

By Bern Klein, Randy Blaskovich, Reem Roufail

"Morphology is a tool that is rarely used for mineral breakage mechanism evaluation. Ground particles are typically assessed for their size distribution. They are also visually analyzed using image analysis. However, image analysis is not a comprehensive evaluation of the particle surface texture. It evaluates particle’s size parameters such as area, diameter, and perimeter amongst other features. On the other hand, morphology analysis takes the particle assessment to another level of detail. Morphology analysis evaluates particles’ roundness, elongation and angularity that would indicate the degree of roughness of the particle. According to Roufail and Klein (2009), rougher surfaces are generated due to breakage along grain boundaries – intergranular breakage. Mill operation, particularly mill speed, dictates the dynamics in the mill. Stirred mills are known to break the particles via abrasion under standard operation. However, if the dynamics of the grinding media in the mill are changed, the particles could be more exposed to impact and compression loading that would lead to a different mode of breakage.In this paper, the effect of material properties and mill operating conditions on particle morphology will be studied. Hard non-sulfide versus soft sulfide minerals are compared, namely quartz and galena, respectively. Extreme mill speeds are tested covering the range of 1000 to 2000 rpm for a 4-litre Netzsch (ISA) mill. In addition to particle size distribution, micro-analysis is executed in the form of morphological analysis using a tested manual roughness point counting technique.INTRODUCTIONGrinding in general and stirred milling in particular are processes that are used to break particles to liberate metal-bearing minerals for further separation downstream. The energy required to achieve the target particle size versus maximum possible liberation has been studied intensively and it is usually the breaking point for the grinding system chosen in a process flowsheet. Operating conditions are dictated by the energy consumption. Becker et al. (2001) related different forms of energy such as input, specific, volume/mass specific energies to stress intensities and final product fineness. Other research studies focused on energy input in a stirred mill (Zheng, Harris and Somasundaran, 1996)."

Jan 1, 2011

Optimizing production scheduling in open pit mines is important for managing cash flows of mining operations. This paper describes a new, probabilistic, mixed integer programming (MIP) formulation which has been developed to minimize the risk of not achieving planned production targets, in terms of metal production and ore tonnage feed for the mill during production, while considering maximization of total discounted economic value. The new MIP model also recognizes that to minimize movement of excavators over long distances and accommodate equipment access, the blocks scheduled for mining within a period cannot be spread too widely. The model is applied to a laterite nickel-cobalt deposit, as an example of multi-element deposits that have complex ore quality constraints. The results show that the proposed model generates feasible schedules. When compared with traditional optimization techniques, the new model is superior in terms of minimizing the risk of not meeting production targets, especially at the early stages of production, and in terms of generating practical scheduling patterns.

Jan 1, 2006

By Claude Bazin

"The On-Stream Analyzer has proven and is still proving to be an extremely valuable tool for the control of flotation circuits. This paper examines the possibility of going further in the utilization of the provided assays using a real-time material balance program to calculate the distribution of solids within the streams of a circuit. Mass balance results can be used for process control, process analysis and detection of sensors malfunction. Examples from 3 Canadian and one American concentrators are presented to illustrate the potential of the method.IntroductionThe On-Stream Analyzer (OSA) has gained, over the last two decades, the status of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant and its application in oxide mineral flotation plants is increasing. On-Stream Analyzers provide X-rays pulse counts that are converted into assays using multilinear regression programs. The estimated assays are passed to the flotation operators, via an operator console, or to control loops of various degrees of complexity (McKee, 1991) implemented in a Distributed Control System (DCS). Operators and/or controllers take control actions based on these assays to ensure an adequate operation of the plant. Although this application pays off very rapidly for the purchase of the OSA, one should ask: Could we get more from the OSA?Some plants reported the use of OSA measurements to process optimization (McKee, 1991). The optimization strategy is based upon economic indices calculated from metal recovery using the 2 product formulae (Wills, 1992, page 124). The 2 product formulae is however sensitive to measurement errors in the assays and can lead to considerable scatter in the calculated indices (Hodouin et al., 1993). Least squares algorithms provide an interesting alternative to filter out measurement errors (Spring, 1992). This paper presents a recursive least squares algorithm that estimates in a real time fashion the mass flow rates in a flotation plant using OSA and mass flow measurements. The algorithm is robust and its recursive structure is not demanding in terms of computation time and memory. The method was tested with data from four concentrators. Results of the material balance algorithm prove to be useful to detect sensors malfunction and may potentially be used for the control and optimization of flotation plants.The paper is divided into two sections. The first section gives a description of the proposed method. The mathematics of the method are kept to a minimum, since the detail is presented elsewhere (Bazin and Franklin, 1994). The second section shows the application of the method to different flotation plants."

Jan 1, 1995

By Paul Grady, Martin Froehling, Curtis Mohns, Eliab Roman

"Since the idea of processing rock to unlock the valuable minerals inside was put into practice, efforts to improve production began. Methods have been learned that allow for operation in environments and under circumstances where it would not have been possible until now. All existing operations have experienced at least some form of productivity improvement measures. The objective is simple: generate more product of better quality in less time and at lower unit cost. Since the year 2000, various modifications have been made at the Kemess Concentrator in efforts to improve productivity. The following is a discussion of these modifications and their contributions to the success of the operation.INTRODUCTIONThe Kemess South Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines with a modern mill controlled by a fully integrated Foxboro IA DCS system and employing 134 people. On February 11, 2000 Northgate Exploration Limited (now Northgate Minerals Corporation) acquired Kemess Mine from receivership. Since acquisition in 2000, Kemess has seen many accomplishments, including the reduction of costs by 40% site wide.The mill has a nameplate capacity of approximately 56,000 tonnes per day which is processed through a Metso (Svedala) 60” x 89” Primary Gyratory Crusher and then conveyed by a 60” conveyor to a stockpile with 48 hours of total storage capacity. The nominal minus 6” rock from the stockpile is fed to two parallel grinding circuits (A & B). Each section consists of a 10.4 m F x 4.7 m SAG mill with dual drive motors (4,480 kW apiece) discharging onto a 2.4 m x 7.3 m Metso (Svedala) single deck vibrating screen to remove the coarse material for recycle to the SAG mill by a Continental 45º high angle sandwich conveyor. Screen undersize is pumped along with ball mill discharge to a cyclopac consisting of twelve Krebs 66 cm F cyclones to classify flotation feed to a size of approximately 65% minus 200 mesh. Cyclone underflow feeds a Metso (Svedala) 6.8 m F x 11.0 m ball mill, also with dual drive motors (4,480 kW apiece). The primary grinding circuit has 35,840 kW available for grinding."

Jan 1, 2005