Search Documents

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011

By Natasha A. Essar

Nevsun Resources Ltd. Bisha Mine Project is a gold and base metal development project in the Gash Barka region of west-central Eritrea. The project has the potential to be one of the largest industrial developments in the country, and Eritreans have no experience in modern mining. Nevsun recognized early that the success of the Bisha Project would require meaningful consultation and engagement with all levels of Eritrean society. Meaningful engagement required not only full disclosure, but also capacity building from government officials at all levels to other stakeholders who live in the nearby communities. This paper describes the approach used to develop capacity and to help introduce a modern mining culture in a country without previous experience in mining.

May 1, 2007

By J. P. Van Cruyningen, M. J. Puro

"A 2400 acre extension to the existing Tailings Area is under development at Inco's Copper Cliff Milling operations.The new area is being developed in stages as production levels dictate thus minimizing immediate capital expenditures while permitting disposal operations to proceed as further site work progresses.The first stage of the new storage site will be fully operational by early 1987 and will include a 400 acre site specific to the storage of Pyrrhotite rejected from milling circuits. The Pyrrhotite site is located in the centre of the Tailings area and is designed for water cover throughout much of its projected life.The new development incorporates perimeter dams designed to operate with low phreatic levels for maximum structural stability. Acid seepage water is collected behind secondary impermeable dams for return to the Tailings Pond.Tailings are deposited by up-stream methods permitting segregation of coarse fractions for use in future lifts of the perimeter dams."

Jan 1, 1987

By R. R. Klimpel

"SYNOPSISA discussion of the importance of flotation rate in the analysis of mineral flotation is presented. In particular, the highly interactive nature of the flotation ""system"" is emphasized where there are components of chemistry, equipment, and operating conditions simultaneously involved. It is further shown that: 1) flotation rate must be measured in order to economically optimize the performance of an industrial flotation circuit, 2) that consistent patterns exist in both flotation rate and equilibrium recovery when changing various settings of the system components, 3) that knowledge of these patterns is necessary in order to avoid making system changes that are either self-compensating or dramatically re-enforcing in some particular aspect of performance, and 4) the rate related role of the chemistry component (e.g.frothers and collectors) is often much bigger than is sometimes realized (especially in a negative sense involving overdosing of reagents). INTRODUCTIONFroth flotation is widely usedl-6 in mineral beneficiation processes as a method for separating different types of finely divided solids present in a liquid (usually aqueous) suspension. The approach is based on the contacting of solids with upward moving air bubbles in an agitated vessel where the solids are exposed to chemicals (collectors) which create a condition favoring the attachment of a certain portion of the solids to the air bubbles. This selected portion is then removed in a froth stabilized by chemicals (frothers) and subsequently recovered from the flotation vessel. Depending on the settings of the various components of the flotation ""system"" (see Figure 1) it is possible to achieve a wide range of flotation performance."

Jan 1, 1984

By Paul Miranda, Corby Anderson

"The Center for Advanced Mineral and Metallurgical Processing (CAMP) has recently obtained a Mineral Liberation Analyzer (MLA). CAMP has utilized the technology for several projects with excellent results. The MLA is able to both analyze size and quantify mineral phases. Therefore, the MLA is becoming the Sherlock Holmes of the mining and metallurgical industry. For this presentation, four projects have been evaluated and data was collected using the MLA. The first project involved tungsten mine. Previous mining practices have yielded poor tungsten results and recoveries. By using the MLA, tungsten mineral phases, along with possible contaminants, were verified and the results used to try to increase overall tungsten recoveries. The second project evaluated a molybdenite/chalcopyrite concentrate with surprising results. The third project is a silver project. Initial flotation scoping tests were performed by attempting to separate silver from gangue material. Because of the poor recovery results (less than 5%), MLA was used to determine possible scenarios for increasing silver recovery. Finally, the last project involves gold evaluation in tailings. For all projects, MLA application results will be presentedand discussed.INTRODUCTIONThe Center for Advanced Mineral and Metallurgical Processing (CAMP) has recently received a software add-on to a scanning electron microscope (SEM) located at Montana Tech. The Mineral Liberation Analyzer (MLA) technology was developed by Dr. Ying Gu of the JKTech Center of the University of Queensland. Since August 2006, CAMP has received and processed over 50 samples. These samples include a total mineralogy of tungsten ore samples, gold tailings, lead zinc tailings pile, molybdenite concentrates, copper concentrates, as well as others. During analysis of these received samples, the technology allows the samples to be quantified mineralogically with some surprising results.For analysis, the samples were initially sieved between 170 to 200 screen sized mesh. This ensures that received samples mineral size is fairly uniform. The samples are then placed into epoxy and allowed to harden. Next, the samples are polished and carbon coated for MLA analysis."

Jan 1, 2007

By D. Mark Richards

Highland Valley Copper (HVC) is a large open pit copper mine in the southern interior of British Columbia. Machine guidance technology using GPS has been utilized at the mine since 1996 for blast hole drill navigation and since 2000 for shovel and dozer navigation. Since 1997, rock recognition has been part of the drilling process. This allowed the mine to develop a Mine to Mill strategy using the rock hardness information from drill monitoring systems to both refine drilling and blasting parameters as well as downstream crushing and grinding strategies. Although this preliminary effort has been very successful at HVC, the current intent is to gain further benefits through better use of existing information while also deriving an enhanced data set from monitoring production drills. In the latter case, the objective is to acquire and process drill variables in such a manner as to permit more detailed definition of rock mass characteristics. The subsequent focus will be to use the derived geotechnical and geological information as part of a practical process to more prescriptively blast the rock mass. Through the definition of domains based on drill monitored derived rock mass properties, the intent will be to enhance blast outcomes that lead to optimized downstream (from blasting through to concentration) processes in a more proactive and timely manner. This paper examines a proposed approach to be able to derive more accurate and consistent rock mass properties from production drilling. In addition, the discussion will identify potential benefits to be gained from process improvements that result in enhanced productivities, and crushing and grinding optimisation due to blasting strategies that are more closely matched to identify rock mass characteristics.

May 1, 2007

By Tarrant Elkington

Underground mine planning practices are typically manual and time consuming and will often produce sub-optimal solutions due to the application of generic rule-of-thumb assumptions or ?tried and tested? choices. The development of computer-automated tools for underground mine planning enable a wide range of scenarios to be considered rapidly in arriving at an optimised solution, subject to input assumptions. We have applied these tools to demonstrate ?optimised? solutions that challenge industry standard practices. Further, we have incorporated grade and price/cost uncertainty into these tools to gain an understanding on how the consideration of uncertainty may further alter strategy selection. Finally, we enable the tools to dynamically adjust cut-off grades in conjunction with the evolution of prices/cost.

May 1, 2010

By Denis Labrie

Le minage en profondeur sous contrainte modérée à élevée présente de nombreux défis aux opérateurs et aux ingénieurs de mine notamment au niveau du contrôle de terrain et de l?environnement minier souterrain, pour assurer la sécurité des travailleurs sous terre et la continuité du cycle d?opération. Des conditions de contrainte élevée signifient une pression accrue au front de taille et sur les structures minières tels les piliers de mine et les fins de zone, un risque de rupture violente ou de coup de toit plus élevé, des zones de rupture plus grandes au pourtour des excavations, des charges accrues sur le support de terrain, etc. Le présent article fournit un aperçu du travail fait à l?intérieur du Programme de Contrôle de terrain de CANMET au cours des sept (7) dernières années, entre 1995 et 2001, pour comprendre et suivre l?évolution des niveaux de contrainte à l?intérieur des structures minières. Les propriétés déterminées en laboratoire sur des échantillons rocheux et les prévisions effectuées au moment de la conception sont comparées avec les observations effectuées en chantier à la paroi des excavations et à l?intérieur de la masse rocheuse. La plupart des cas discutés ici montrent une corrélation satisfaisante entre les observations effectuées en chantier d?une part, et les résultats d?essai obtenus en laboratoire et les calculs réalisés lors de la conception d?autre part. Ces observations peuvent donc être considérées comme des moyens relativement sûrs pour vérifier et suivre l?évolution des niveaux de contrainte présents à l?intérieur des structures minières.

May 1, 2002

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015

By W. W. Culver

The paper explores the substance, circumstances and significance of the Whelpley and Storer Copper Process. The 1866 Whelpley and Storer patent specified a process combining mechanical and chemical engineering. The process called for a down-drafting shaft furnace with a horizontal flue connected at the bottom of the shaft. Powdered sulphide ore was roasted in the shaft and then sent forward fully oxidized to a bath of sulphuric acid and/or calcium chloride. The “water furnace” was developed in Boston, at a time when the city was home to most Michigan copper mining companies. The process was field-tested at Quebec’s Harvey Hill copper mine. In 1865 James Douglas, Jr. took over management of the Harvey Hill mine with the challenge of saving the family investment. He needed a way to make money from low-grade sulphides. Through his relationship with chemist T. Sterry Hunt, Douglas learned of a possible way ahead using the process developed by Whelpley and Storer. The paper confirms the centrality of publications, meetings, and networking in the advancement of metallurgy. The process is of interest historically, as much as anything, because it is one of the pillars of James Douglas’ distinguished career in copper. INTRODUCTION At the 1866 meeting of the American Association for the Advancement of Science (AAAS) in Buffalo, New York, T. Sterry Hunt (1826–1892) read a paper “On the Metallurgical System of Messrs. Whelpley and Storer.” The paper is part of a chain of events that constitute the foundation of James Douglas’ (1837–1918) success in the copper mining industry. To understand the career of Douglas over the early years of modern copper mining, we must necessarily start with Whelpley and Storer. Going back to Hunt’s paper, he concluded his remarks by asserting that the Whelpley and Storer Process was “capable of such wide and varied application, that it is probably destined to have a very important influence on the industry of the world” (Hunt, 1867a). He reached this conclusion reasoning that the process had overcome a critical metallurgical hurdle (Hunt, 1867a). Hunt, a geo-chemist in modern terms, recalled that the chemist of those years easily separated copper from “sulphuretted” ores by converting it to a soluble salt from which pure metal was precipitated by “an equivalent of iron.” The problem was to “…apply this principle in the working of copper ores on a great scale...” (Hunt, 1867a). Hunt noted that this very problem had “…engaged the attention of many metallurgists, and has given rise to various processes for obtaining copper by the moist way, many of which are nearly or quite perfect in their operation, but are lacking in practicability and cheapness” (Hunt, 1867a). Hunt thought Whelpley and Storer had overcome the low-grade sulphide hurdle with a commercially viable engineering breakthrough. Yet in the history of copper metallurgy, the process is missing. What happened?

Jan 1, 2019

By M. Doggett

All 231 Canadian primary gold mines that produced from 1946 to 2004 were analyzed with respect to their production and economic characteristics. Trend analysis revealed that the average annual capacity of Canadian gold mines, as measured by ore processed or gold produced, has increased over time. Conversely, the average grade of gold mines has decreased over time. The distribution of gold output is highly uneven: for example, the 22 giant mines producing more than 100 t (metric tonnes) of gold account for 62% of total output. Small mines producing less than 10 t Au account for 54% of total mines, but less than 4% of total gold. Each historical mine in the database was evaluated on the basis of a set of economic and technical assumptions to determine if it would be economic to develop today. Based on the net present value using an 8% discount rate, only 103 of the 231 mines were determined to be economic. About 80% of the uneconomic mines had less than 10 t of contained gold, and 63% had less than 5 t. It is concluded that these small mines would not be viable today due to a combination of real capital cost increases, and more stringent permitting and environmental regulations. The implication is that future gold supply in Canada will hinge on the discovery and development of a new generation of larger mines. Given that only one giant mine has been discovered in the past 20 years, it seems likely that gold output will decrease in the future.

Jan 1, 2007

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

By Zuhair A. Nawab, Muhammad A. Al-Marhqun, Mehmet Guney

"The Atlantis-Il-Deep is a stratified metalliferous deposit located along the median valley of the Red Sea at a water depth of about 2200 m. The metal-bearing mud contains sulphides of zinc, copper and iron with significant amounts of silver, gold and cobalt. A variety of oxide, siliceous and carbonaceous gangue material is also present. Long sediment cores indicate that the thickness of the deposit may reach 25 m, but the average kriged thickness of metal-rich sediments is about 11 m.Mining geostatistics was applied to estimate the Red Sea offshore mineral resources. Experimental semi-variograms were computed along 0 ± 180 degrees and then models were fitted to analyze the mineralization phenomenon. Kriging estimates indicate that 696.330 million t of bulk sediments contain 1.891 million t of zinc, 0.425 million t of copper and 3. 75 thousand t of silver. Gold and cobalt contents were calculated from the analysis of solids in flotation concentrates as 47 t and 5368 t respectively. The significant outcome of implementing geostatistics to the Red Sea brine precipitates is not only for the evaluation of metal resources, but it also provides a useful tool in the optimization of selective dredging of appropriate areas to be mined. IntroductionThe discovery and extensive exploration of hot brines and hydrothermal sediments in the Red Sea median valley revealed the fact that the Atlantis-II-Deep is a potentially exploitable metalliferous mud in the economic sense. Sediments in the mineralized deep are composed mainly of oxides, various types of silicates and sulphides with considerable concentrations of zinc, copper, cadmium, silver and gold. The mineral-rich deposit, located at a mean water depth of about 2000 m, has an average thickness of 11 m, and is covered by a brine layer having a temperature of 60°C."

Jan 1, 1988

By Adil Aledresse, Louis Mercier, Laxman Amaratunga

"The development of high capacity adsorbents with uniform porosity denoted, MP-HMS (Mercaptopropyl – Hexagonal Mesoporous Structure) using nanotechnology, and their ability to extract gold from solution, is presented. The preparation of highly effective heavy metal ion adsorbents by the incorporation of thiol moieties into the pore channels of mesoporous silica molecular sieves has been the subject of many nanotechnology research investigations. The unique feature of these nanoporous adsorbents is their ability to adsorb gold ions from ultra-low concentration solutions like mine effluent as well as from leached solutions in gold mills. The preliminary studies from laboratory simulated gold solutions show that the adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 370 mg gold per one gram of the nanomaterials from Tetrachloroaurate solution (up to 37% of their weight). Experimental studies indicated that the maximum adsorption of gold (as high as 99.9% recovery). The current studies will be extended to investigate the interaction of ionic gold complexes with nanomaterials. Future development of this work may lead to either to replace the conventional CIP/CIL processes or use nanomaterials in tandem with the former, suggesting plausible use of mesoporous material in pulp, MIP or in leach, MIL, as a novel gold extraction process.INTRODUCTIONGold typically occurs at very low concentrations in ores less than 10 g/t or 0.001% (mass basis). At these concentrations the use of aqueous chemical (hydrometallurgical) extraction processes is the only economically viable method of extracting the gold from the ore. Typical hydrometallurgical gold recovery involves a leaching step followed by the separation of the gold bearing solution from the residues, or adsorption of the gold onto activated carbon adsorbent. After elution from the activated carbon the gold is further concentrated by precipitation or electrodeposition."

Jan 1, 2008

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments. A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including respectable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects. Reflecting the observation of a wide range of views regarding the subject of inflation, this paper will-address the impact of five different approaches to inflation on the evaluation of a single Canadian mining project."

Jan 1, 1987

By C. J. A. Davie

"SUMMARY A practical application of nitric acid oxidation of sulphides, based on the principles of the Arseno process, has been developed for the Cinola ore. Development of the process has been based on testwork conducted by Bacon Donaldson of Vancouver and Hazen Research of Denver, and on conceptual engineering performed by Minproc Engineers of Denver.A comprehensive Stage II report for the project has been submitted to the B.C. permitting agencies, containing provisions for a zero discharge tailings impoundment system and prevention of acid mine drainage. Approval in principle is expected in early 1989.A feasibility study recently completed by Minproc Engineers and Davy McKee Corporation demonstrates that this project can be brought to production for a capital expenditure of C$120 million for a mill throughput of 6,000 tonnes/day and operated at a total direct operating cost of less than $20/tonne.INTRODUCTION The Cinola orebody was discovered in 1970. It is situated approximately in the centre of Graham Island, the largest of the Queen Charlotte Islands. It represents the mid to upper levels of a hydrothermal precious metals system, characterized by intense brecciation and silicification. Gold is associated with finely disseminated sulphides in a breccia matrix and in free form in numerous quartz veins.Ownership of the property has changed hands a number of times, and previous attempts to bring the property to production have failed. Two critical factors have frequently been blamed for difficulty in creating a successful project: namely, process and environment factors, hence the title of this paper.City Resources (Canada) Limited (""City"") acquired the property in 1986, and commenced an aggressive campaign to verify ore reserves, to carry out metallurgical research and to address environmental issues.PROJECT OVERVIEW When the Cinola orebody was discovered, the significance of hydrothermal mineraliza¬tion associated with crustal plate boundaries was not recognized, and for several years, the orebody was considered an uneconomic curiosity. If the type and location of orebody sought by many companies engaged in gold exploration were to be specified, it would probably be a description of the Cinola orebody - it is a large (greater than 1.5 million ounce), low grade (2.45 gm/tonne), refractory ore reserve associated with the Pacific rim crustal plate boundary. The industry appears to have recognized in the past few years that its future lies in the exploitation of such orebodies, and is prepared to come to grips with the technical problems associated with such ores. In this sense, the Cinola orebody might be considered to have come of age."

Jan 1, 1989

By Marie-Eve Boucher

The slag in iron ore pellets allows wet sintering during firing and leads to suitable bounding. The process of slag formation differs whether it takes place in the core or in the external zone of a pellet. In the core, hematite can be reduced to secondary hematite, depending on the temperature and on the carbon monoxide/dioxide partial pressure ratio. The reaction rim that appears at the outskirts of a silica particle in contact with the FeO bearing magnetite is considered as the slag precursor in the core of the pellet. By contrast, in the external zone of a pellet, where O2 is available and CO partial pressure is very low, the first step towards slag formation is flux decomposition, mainly dolomite and limestone. The CaO liberated through this reaction will be available to react with hematite by solid diffusion to form calcioferrites, which play an active part in the slag evolution process. These two slag formation paths will be explained.

May 1, 2007

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units."

Jan 1, 2012

By E. Gallestey, D. Groenveld, F. Kolb, M. Rozou

"Recent copper price evolution pushes modern mining industry even harder to achieve highest production with maximum efficiency. Operations are bound by numerous contractual and environmental conditions that bring a high degree of complexity to both the operators controlling the process and the plant managers assessing the circuit’s potential and setting the production goals.Advanced process control (APC) for grinding is one important tool to operate this most energy intense area in an optimal way, finding the optimal trade-offs between highest throughput, energy efficiency and product quality based on variable ore properties, production targets and management priorities.ABB’s state of the art control and optimization software platform enables user to design a controller based on model predictive control (MPC). The paper and the presentation show the technology used and the results achieved through an APC controller installed in a pilot project in Aitik (Boliden SA), Sweden. Furthermore, possibilities to interconnect grinding with other areas as stockpile management and flotation with various interconnected APC controllers will be shown. Finally, an example of the return on investment and the payback times based on the increased throughput and better product quality will be presented.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations (see Figure 1).The main goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. At the same time, it is also crucial to execute this process at the lowest possible energy and grinding media consumption."

Jan 1, 2015