Search Documents

By John D. Carr

Introduction The Flin Flon zinc plant operates on what is known as the low density or standard sulphate process, that is, the zinc is carried through the plant solution circuit attached to the SO4 or sulphate radical at a concentration not exceeding 175 grams per litre zinc. The process may be described briefly as follows: The zinc is received in the zinc concentrate chemically combined with sulphur and mixed with many other impurities. The concentrate is roasted and most of the sulphur is burned to a gas, which is discharged from the plant. The roasted concentrate, or calcine as it is called, is leached with a weak sulphuric acid solution so that the resulting leach solution contains a high zinc content but a very small proportion of the impurities. The solution is separated from the solids and is purified further by agitation with zinc dust to remove copper, cadmium, and cobalt. This purified zinc sulphate solution is then pumped to the electrolytic department. The solids from the first leach are again leached, but this time with a stronger acid solution to dissolve all of the remaining zinc which is soluble in the strength of acid available. The solids and solution from the leach are then separated. The solids are stock-piled for further treatment at some future date and the solution, carrying a relatively high amount of impurities, is sent to the first leach, where the chemical action is such that the contained impurities are precipitated as solids. The electrolytic department is nothing more than a large number of electroplating cells in which the zinc is plated on aluminium sheets. Since zinc does not plate tightly to aluminium, the zinc plating or sheet is easily stripped from the aluminium and the sheets are collected to be melted and cast into the standard market bars or slabs. In the electro-deposition cells, the zinc sulphate (ZnS04) is split to metallic zinc (Zn) which plates out, and sulphate (S04) which combines with the hydrogen of the water of the solution to form sulphuric acid (H2S04). When one pound of zinc is deposited, about one and one-half pounds of sulphuric acid are formed. This acid is sent to the leaching section, where it dissolves one pound of zinc from the calcine. The solution is purified and is again pumped to the plating cells. The solution travel forms a complete circuit.

Jan 1, 1935

By A. H. A. Robinson

Until quite recently-practically up to the present time-all but an insignificant amount of the copper produced in Canada was shipped abroad in the form of ore, matte, blister, etc., there to undergo the further treatment necessary to bring it to the refined state in which it is required by fabricators of copper. Consequently, Canadian manufacturers were forced to import nearly all the copper required in their business; and a considerable portion of the ultimate value to be derived from a Canadian raw material was lost to the country of its origin. In the early days of Canadian copper mining, when both the production and consumption of copper in Canada were much smaller than now, such a condition of affairs was perhaps economically unavoidable, and, in any case, was not a matte~ of sufficient importance to attract general attention. Later on, however, when there had been large and rapid increases both in the production and consumption of copper in Canada, it formed the basis of much adverse criticism, deserved or not, of producers of Canadian copper-criticism that became intensified during the war and subsequent years. Happily, the chief grounds of complaint have now been removed, and there are today copper refineries in Canada, either operating or under construction, that are capable, in the aggregate, of turning out amounts of refined copper greatly in excess of any indicated Canadian consumption.

Jan 1, 1931

By Rick Valenta

Is the Labrador Central Mineral Belt part of the IOCGU Club? ?I sent the club a wire stating, PLEASE ACCEPT MY RESIGNATION. I DON'T WANT TO BELONG TO ANY CLUB THAT WILL ACCEPT ME AS A MEMBER.? GrouchoMarx Acknowledgements ?Ian Dunlop, Matt Lennox-King, Mark O?Dea, Dave Barbour, Derek Wilton, Lucas Marshall, Roland Butler, Mark King, Sally Howson,

May 1, 2006

By R. Stauffer, S. Lindsay

"Sherritt Gordon Mines Limited utilizes pressure hydro-metallurgical techniques to recover nickel, copper and cobalt from su1phidic concentrates, mattes and various other metal-bearing materials.A brief description of the nickel refinery operation is given. In the nickel refinery process, an ammonia pressure leach is employed to treat the feed materials to dissolve the non-ferrous metals as their respective ammine complexes. The resulting leach solution goes through a series of steps which removes copper as copper sulphide and further purifies the solution prior to nickel precipitation by hydrogen reduction. The reduction end solution, containing the cobalt which was originally present in the leach solution as well as residual nickel, is treated with hydrogen sulphide. The resulting nickel-cobalt sulphide precipitate feeds the soluble cobaltic ammine process, which separates the nickel and cobalt and recovers the cobalt as a pure powder.A detailed description of the cobalt recovery process is given. Included are the various steps, comprising: acid leaching of the mixed sulphides, solution purification, ammine complex formation and cobaltous oxidation, two-stage nickel precipitation, cobalt conversion and reduction. A brief description of cobalt powder handling is included, along with typical physical properties and chemical analyses of the cobalt product. In general, the purpose of this paper is to describe the present plant practices employed in the recovery of cobalt as a by-product of the nickel refinery operations."

Jan 1, 1967

By B. Wasmund, M. Y. Solar, I. Candy

The nickel laterite industry is divided into two camps when it comes to the grade of the ferronickels produced. One group, led by Falcondo and Cerro Matoso, markets high-grade ferronickels in the range of 35 to 40% nickel, while another group, led by SLN and the Japanese smelters, favour lower grades in the range of 20 to 25%. Because the ores processed by these smelters vary widely in terms of nickel content and iron to nickel ratios, it is probably more accurate to classify these smelters in terms of their iron recovery: Falcondo and Cerro Matoso smelt at lower reduction potentials and thus recover only 15 to 30% of the iron in their ores, while SLN and the Japanese smelters are very reducing and recover 45 to 65% of their iron. Low reductions generally imply higher slag losses and lower nickel recoveries, but also lower power and reductant requirements; higher reductions, the reverse. The question is, therefore, whether an economically optimum ferronickel grade exists for processing any given ore. This paper proposes a methodology for determining this optimum grade and concludes that nickel laterite smelters should favour low reductions and production of high-grade ferronickels.

Jan 1, 2008

By K. Schimann, H. D. Knipping, J. P. Fouques

"RESUMELe gisement d 'uranium de Cigar Lake, dans la région de l'Athabasca au nord du Saskatchewan, fut découvert en mai 1981 par Cogema Canada Ltée, opérant pour Ie compte de la ""Waterbury Lake Joint Venture"".Le corps minéralisé. qui est dépourvu de toute expression directe en surface, est situé a la discordance entre les met sédiments du wottaston Group (Protérozoïque inférieur ou Aphébien) et les grès de l 'Athabasca (Protérozoïque moyen ou Hélikien), à une profondeur de 410 a450 m.Fin 1984, Ie gisement était reconnu par 105 sondages minéralisés repartis sur une longueur de 1800 m, pour une largeur comprise entre 25 et 105 m. 11 se présente sous forme d’une lentille aplatie de 5 a30 m de puissance, et montre une remarquable continuité d'ensemble. Une ride ou bombement topographique de la discordance est associée au gisement surtoute sa longueur.A l'échelle régionale, le corps minéralisé à est associe à un corridor structural d’orientation est-ouest, a l'intérieur duquel des facies particuliers aténdance blast mylonitique sont développes dans les formations métapolitiques agraphite du socle métamorphique. Il est entouré par un halo d'altération très important, caractériser Ie développement de minéraux argileux alumino-magnesiens (illite-chlorite).La minéralisation est située, pour la plus grande part, dans les grès d'Athabasca, et se compose essentiellement d'uraninite et de sulfo-arseniures de nickel et de cobalt,De nombreux levés géochimiques et géophysiques ont été effectues dans la région de Cigar Lake. Aucune anomalie ne peut être associée directement au corps minéralise, mais la combinaison des données en provenance de plusieurs sources s’est révélée fort utile au niveau de l’interprétation géologique régionale et de la définition des cibles de sondages a l'intérieur des zones reconnues favorables.Le gisement de Cigar Lake présente de nombreuses analogies avec plusieurs des gites classiques de la région de l'Athabasca; il est caractérise en particulier par l'intensité des phénomènes d’altération et la présence de minéralisations extrêmementriches.En 1984, les réserves géologiques globales estimées par géostatistique sur I ‘amas minéralise principal s 'élevaient a 110 000 tonnes d'uranium, aune teneur moyenne de 12.2%, avec une précision de 25% à l'intervalle de confiance de 95%.ABSTRACTThe Cigar Lake uranium deposit, in the Athabasca area of North Saskatchewan, was discovered in May 1981 by Cogema Canada LId., as operator of the Waterbury Lake Joint Venture. The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sands tone, at a depth of 410 m to 450 m below surf ace.AI the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25 m and 105 m. It has the shape of a flat-lying lens 5 m to 30 m thick and shows a remarkable longitudinal and latera continuity from the information obtained to date. A well-defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west-trending structure within which a particular rock facies (""augen gneiss"") has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-A I rich clay minerals (illite-chlorite).The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfo-arsenides of nickel and cobalt.Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, although there may be locally a good coincidence. However, a combination of several methods proved extre"

Jan 1, 1986

By D. Komljenovic, E. Lafontaine, J. Paraszczak

Availability of the production equipment used in underground mines has a substantial impact on production costs and, thus, on mine profitability. Appropriate collection of pertinent data and information, as well as use of adequate performance measures and their analyses, can help mine operators identify cost-effective opportunities to improve equipment availability. This paper presents study results aimed at reviewing and analyzing means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews sources, as well as quality and quantity of relevant data and information, and examines performance measures and their definitions, as applied to surveyed mines. Problems concerning data acquisition and meaningfulness of the performance measures are discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. Evidence suggests that the latter may become a more useful tool for mine operators in their efforts to reduce production cost.

Jan 1, 2008

By E. Laatio, W. McKay

"History of Tara Mines Ltd.Tara Exploration and Development Company Ltd. was formed in Canada by Irishmen in 1953. The discovery of an orebody approximately six miles from the historically famous Hill of Tara in County Meath was a wild dream . Nevertheless this dream became a reality. Tara Mines Ltd. was formed, and the mine developed some 35 miles northwest of the City of Dublin in the Irish Republic.Tara's original drilling program indicated a zinc-lead orebody of approximately 60 million tonnes grading at 10.1% Zn and 2.6% Pb. The terms of the mining lease stipulated that the Irish government would acquire 25% equity interest in the operation. The mine was thus owned 75% by Tara Exploration and Development Company Ltd. of which the principal shareholders were Noranda and Northgate, together with 25% being held by the Irish government. The mine was purchased in March 1986 by Outokumpu Oy, a Finnish mining and metallurgical company, and together with the 25% government stake are the current owners. Outokumpu Analysis on Tara Mines Ltd.Upon ownership Outokumpu carried out a comprehensive analysis on the operation and came to the following conclusions :1. Tara had a good orebody;2. Tara had a skilled, capable, stable workforce;3. Tara's concentrator and processing equipment was adequate to meet requirements;4. Tara's mobile equipment fleet was too old and too numerousin numbers; and5. Tara had too many employees, both staff and hourly paid .With ore reserves of approximately 50 million tonnes and at a planned extraction rate of 2.6 million tonnes it meant that the mine had a lifespan of approximately 20 years. To be a viable operation into the future, the mine had to become more efficient. Operating costs and manpower levels had to be dramatically reduced."

Jan 1, 1989

By P. D. R. Maltby

"The Canadian Institute of Mining and Metallurgy has undertaken to host the XIV International Mineral Processing Congress to be held in Toronto at the Royal York Hotel from October 10 to 16, 1982. The theme of the Congress will be ""Worldwide Industrial Application of Mineral Processing Technology."" The program will include 10 sessions and numerous field trips to the different mining areas of Canada.For prospective authors, the preliminary program includes sessions on,1. Flotation - plant practice, equipment design, simulation, control and economics.2. Comminution - plant practice, equipment, design, simulation, control, wear, energy consideration and economics.3. Round table seminar on large grinding mills.4. Round table seminar on modern and future plant design.5. Mineral processes to recover precious metals.6. Mineral processes to recover energy minerals (coal, uranium).7. Mineral processes to recover industrial minerals.8. Round table seminar on the environment and ecology and how the different countries cope with associated problems.9. Materials handling with an emphasis on agglomeration techniques ereconentration methods, solid-liquid separation.10. Open session to deal with topic emerging from general demand."

Jan 1, 1980

By N. M. Soonawala

Detailed regional geophysical and geochemical surveys, ground surveys and drilling were undertaken to follow-up the federal-provincial Uranium Reconnaissance Program (URP) over the 27,OOO-km2 Kasmere-Munroe area in northwestern Manitoba. An analysis of the URP data showed a fair correlation between the regional airborne radiometric results and lake-bottom geochemical results, both of which also correlated with the regional geology. More detailed surveys defined anomalies with greater precision within the broad zones outlined by the URP. The ground follow-up indicated that URP anomalies can be caused by varying degrees of uranium concentration in the rocks. Mineralization of interest was found in leucogranites at several locations within the survey area. Anomalous uranium concentrations were also found in coarse pegmatites and Hudsonian granitic intrusions. It can be concluded that large-scale regional surveys can be followed up in relatively short periods of time to yield meaningful results if a properly planned exploration sequence is employed, each stage of which successively narrows the area of interest.

Jan 1, 1979

By S. Kwon, J. W. Wilson

"In salt and potash mines, the time-dependent deformation mechanism should be clearly understood based on in situ measurements to predict the performance of a mining design. In this study, in situ deformation measurements from the Waste Isolation Pilot Plant (WIPP) and other salt and potash mines were used to determine the transition time from the primary to the secondary creep stage and to investigate the influence of adjacent excavations such as a nearby tunnel excavation, panel excavation and/or pillar extraction on rock deformation. IntroductionThe deformational behaviour of underground excavations in salt and potash mines is complex due to the time-dependency of the rocks. When the material properties are determined from laboratory tests, they should be carefully applied to in situ conditions, because in situ conditions are completely different from laboratory conditions. For instance, in situ deformation measurements show that the deformation rate decreases with time similar to those observed in the laboratory during the early stages. However, the rapid decrease of deformation rate does not come from the microscopic strain hardening effect observed in laboratory tests, but mainly from stress relief around the opening after its excavation (Baar, 1977). It is, therefore, recommended to undertake in situ measurements and use them to understand the deformation mechanism.Even though in situ measurements are widely accepted as important information for understanding the deformation mechanism of salt and potash (Barr, 1971; Kovari and Amstad, 1993), not many publications have focused on the fundamentals of data measurement, the application of the measured data, and the development of data analysis techniques. Recently, several new techniques for better understanding the deformation mechanism of rock salt have been developed that are based on in situ measurements. Kwon and Miller (1995) developed a new technique for describing the actual deformational behaviour of an underground excavation in rock salt. The migration of “zero strain boundary,” which represents a no movement boundary around an underground excavation, could be calculated by the technique developed by Kwon and Miller (1996). Kwon and Wilson (1997, 1998) applied neural network techniques to in situ deformation measurements to predict the deformational behaviour of the underground excavations at the Waste Isolation Pilot Plant (WIPP) located in the United States.In this study, in situ deformation measurementsfrom the WIPP site and other salt and potash mines in the United States were extensively analyzed to understand the deformation mechanism of the underground excavations in the rock mass."

Jan 1, 2002

By K. N. Subramanian

Previously reported work on total oxidative leaching of chalcopyrite concentrates ha s shown that high copper extractions are obtained at 210°C and 0.4 MPa oxygen pressure. A simple integrated flow sheet using pressure leaching, solution treatment involving precipitation with a calcium base, and electrowinning to produce wire-bar-quality copper is described. Reagent and energy requirements developed from this work indicate that the process could be attractive for small operations where a smelting-refining complex cannot be justified.

Jan 1, 1978

By P. Cheung, J. Gulyas, R. Clary

Over the past 50 years, the use of autoclaves in the metallurgical industry has evolved from final metal recovery (hydrogen reduction) and purification (sulphide precipitate oxidation) to treating whole ores and concentrates. Recent process developments, such as the use of autoclaves for laterite leaching, have necessitated higher temperature and pressure operations, which in turn have seen marked advancements in technology and manufacturing capabilities to keep in step with process demands. This paper will discuss the advances in technology in terms of design, materials and construction of autoclaves and liners, typical dip tube design and geometric layout. This paper will also address specific auxiliary equipment, such as acid and steam injection systems, and components, such as agitator seal systems.

Jan 1, 2004

By A. H. Onur, S. Ural

"The Afsin-Elbistan coal deposit with its 3.4 billion metric tons of reserve is the biggest coal basin and one of the most important resources for electrical energy production in Turkey. The coal deposit is located north of Elbistan, Kahramanmaras Province, in southeast Turkey (Fig. 1).The Kislakoy sub-basin of the Afsin-Elbistan basin was selected as the first open cast mine to feed four power station blocks of 340 MW each. The mine is equipped with six identical bucket wheel excavators of the type Sch Rs (2300/5) 32. The annual coal demand of the power station is 18.5 million metric tons. The Elbistan basin encompasses an area of 900 km2, and its centre lies about 1150 m above mean sea level. The sedimentation took place mainly in the upper Pliocene period. The thickness of the coal bed varies from 20 m to 60 m, respectively. The basal part of the coal beds consists of clay, marl and sandy clay. These formations are overlain by gyttja, which may also occur in the form of calcareous ooze, enveloping coal beds. The thickness of the gyttja is up to 35 m (Otto-Gold, 1969). The coal of Afsin-Elbistan is soft coal and the quality has been found to vary considerably throughout the deposit. The thicknesses of the sterile intercalations vary from 0.50 m to 2.2 m and average 1 m in thickness. From the quality control point of view, the coal seam is regarded as upper seam where the gyttja formation occurs as sterile intercalations, and lower seam where the clay formation occurs instead of the gyttja (Fig. 2). The CaO content of upper Kislakoy coal is very high, grinding resistance is low and base to acid ratio of ash, that is, the ratio of acid oxides of metals to base, is greater than one (Ural and Onur, 2001). Contrary to upper Kislakoy coal, CaO content of lower Kislakoy coal is very low, grinding resistance is high and base:acid ratio of ash is smaller than one. Modified Impact Strength Index (MISI) tests are used to determine the grindability of the Elbistan coals (Ural, 1999)."

Jan 1, 2003

By Witold J. S. Ostrowski

The shaft structure being part of an underground mine, depends on programned functional duties, and on geological and hydrological conditions. The majority of Canadian metal mine shafts are in hard competent igneous rocks, which are in an elastic state of equilibrium around the excavation. Others penetrate soft sedimentary or very weak water-bearing rock formations in which the equilibrium varies from plastic to hydrostatic. Knowledge of how to interpret the underground conditions, determine acting forces and design proper structures is essential for the production and safety of the future mine.

Jan 1, 1973

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

By C. Derek Martin

"Predicting the ground response for tunnels in weak shales remains challenging. Predicting the ground response is challenged by difficulties in characterising the material, and our ability to predict deformations that are driven by coupled hydromechanical processes, when this material yields. The techniques that are used for characterizing weak shales are reviewed, and three case histories are examined that demonstrate the behaviour of these weak rocks during tunnelling. A general framework is provided for assessing the squeezing potential for weak shales.1 INTRODUCTIONGeologically, shale is an argillaceous fine-grained sedimentary rock that forms from the compaction of silt and clay-size mineral particles commonly referred to as ""mud"". Because of this grain size, the material is generically classed as Mudstone (Figure 1). Shale is distinguished from other mudstones because it is made up of many thin layers (laminated) and readily splits into thin pieces along the laminations (fissile). While the geological classification of shale appears straightforward, the classification for engineering purposes is often confusing. Underwood (l967) provided the first description of shale that made the distinction between “soil-like” compaction shales and “rock-like ""cemented"" shales. He coined the term ‘clay shale’ to capture the characteristics of hard clay yet recognizing its origin as a shale. In this paper weak shale is synonymous with clay shale and have strengths that typically range from R1 to R2 (1 to 25 MPa). Characterising these materials draws on methods from both soil and rock mechanics."

Jan 1, 2015

Project Details ? Located 420 km northeast of Yellowknife, Northwest Territories ? Jericho kimberlite discovered in 1995 ? Feasibility study showed +3,000,000 carats recovered from 2.6 million tonne reserve ? Nine year mine life ? Approx. 100 person workforce in full production ? First mine for Tahera, First new mine for Nunavut Completed Ambitious Construction Schedule During 2005 o Feb ? Mar/05 Winter road mobilization o Mar ? Dec/05 Pre-stripping, earthworks o Mar ? Apr/05 Camp facility, occupied May 3 o May ? Dec/05 Process plant o Jun ? Dec/05 Maint. shop, fuel storage, power plant o Jan ? Mar/06 Commissioning, start-up o April 2006* COMMERCIAL PRODUCTION

May 1, 2006

By C. A. Pickles, D. K. Xia

"In the last few decades, microwave energy has been widely employed in food processing, rubber and plastics curing, and in ceramic sintering. Recently, the application of micro waves as an energy source in extractive metallurgy has received considerable attention from a number of researchers. During the period from the mid-1960s to about 1988, the majority of the research was focussed on the behaviour of materials in microwave radiation. These research activities will continue to be important, since fundamental data on the interaction of microwaves with materials are vital for the successful application of the technology. Since1990, a number of potential applications of microwave processing have been investigated.These include: pretreatment of ores and concentrates, leaching, reduction, preheating of refractories, heating of slags and waste treatment. In this paper, the interaction of micro -waves with materials of interest in extractive metallurgy are reviewed and potential applications are discussed.IntroductionMicrowaves were first used in 1946 for the heating of materials, shortly after radar equipment was invented during the second world war. It was evident that microwaves were very effective for heating water and the technology was quickly adopted for drying and cooking. Since the introduction of the first microwave oven by Raytheon in 1952, many millions of domestic microwave ovens have been sold annually (National Research Council,1994; Atomic Energy of Canada and Voss Associates Engineering, 1990).In extractive metallurgy, microwaves are in the early stages of development (National Research Council, 1994; Atomic Energy of Canada and Voss Associates, 1990; McGill and Walkiewicz, 1987; Bradhurst and Worner, 1990;Peng et al., 1993). However, there are several reasons for the growing interest in the use of this technology in the field of metals extraction. These include the following potential advantages of microwaves: (1) rapid and selective heating of materials; (2) reactions can be catalyzed because the heating occurs on a molecular or atomic level; (3) clean and controllable energy source; (4) the gas volume is reduced and the atmosphere can be controlled as there are no gaseous combustion products; (5) the material is heated internally in comparison to external heating with conventional methods; (6)the temperature of the refractory can be minimized; and (7) the working environment is improved."

Jan 1, 1997

By C. M. Clapperton, K. E. Darke, A. J. Boyce, C. M. Rice, S. D. Redwood

"The Kori Kollo gold deposit is hosted by a c.15 Ma sericitized dacite stock in the LaJoya district on the Bolivian Altiplano. The mineralization is of the Bolivian polymetallic vein(BPV) type, with a signi?cant amount of the gold reserves contained in the oxide cap.Field and microscopic studies, K-Ar dating, ??34S values of pyrite, alunite and jarosite, and ??18O values of alunite and jarosite demonstrate that some of this gold is supergene. Two types of supergene gold are present: minute gold grains, 1 to 10 microns across, of high fineness and associated with jarosite and iron oxy-hydroxides; and ‘invisible’ gold, which is probably sorbed onto minerals such as jarosite and iron oxy-hydroxides.Pyrite ??34S values fall in the limited range -3.5 ± 0.6‰, consistent with a magmatic origin. Sulfate ??34S values are homogeneous and overlap closely with those of pyrite (-1.2 ± 2.1‰), which supports petrographic evidence that sulfates replaced pyrite. By contrast, sulfate ??18O values are inhomogeneous with a large range (alunite +2 to 26‰, jarosite -5 to +18‰). These data are interpreted as reflecting kinetically controlled reactions involving various proportions of atmospheric oxygen and local meteoric water. This is typical of supergene alteration and is due to the seasonally dry climate of the Altiplano.The oxide-zone mineralogy is dominated by sulfates and iron oxy-hydroxide minerals with some phosphates and halides, which indicates that the groundwaters were acidic, oxidizing and relatively saline. Under these conditions the most likely complexes responsible for gold mobilization are halides.Geological data and K-Ar ages indicate that oxidation of the BPV deposits began at least around 11 Ma and possibly up to 15 Ma ago, and that supergene alteration lasted until around 4 Ma. During this period, erosion was minimal. Although supergene processes have been active on the Bolivian Altiplano since the Middle Miocene, in contrast to Northern Chile, enrichment of gold has not occurred."

Jan 1, 1997