Search Documents

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities.

Jan 1, 2002

By Han Kook-Nam, Lawson F

The recoveries of the three cobalt minerals in the Mount Cobalt deposit, cobaltite CoAsS, erythrite CO3(AS04)8H20, and new cobalt mineral with a composition approximating 2CoO.CaO.Fe203.2As205.11H2O were investigated using physical and surface-chemical processes.Over 80 per cent cobalt recovery was achieved by tabling a cobaltite-mineralized sample, while about 76 per cent cobalt recovery was obtained by dry feed magnetic separation of a sample containing erythrite and the new cobalt mineral. The resultant primary magnetic concentrate with a cobalt grade of 5.5 per cent, was able to be upgraded to 14.4 per cent cobalt by regrinding .and a further magnetic separation.Electrophoretic mobility - pH responses for each of the three cobalt minerals were found to be similar. Each mineral remained negative over the pH range 3 to 11 and was most negative at mildly alkaline pH values.Cobaltite was floated effectively with amyl and ethyl xanthate collectors under acidic conditions at collector concentrations of 10-2M to 10-5M. Erythrite showed a similar flotation response using 10-sM amyl xanthate. The practical application of these laboratory separations to an industrial process is suggested.

Jan 1, 1976

Agglomeration Drum Selection and Design A model has been developed by for drum agglomeration which allows selection of geometry and power input. Specific aspects considered are: calculation of total operating volume, solids residence time based on drum geometry and operating parameters, selection of the drum aspect ratio, selection of proportion of critical speed, calculation of rotating power requirements. The model uses solids total residence time to calculate the required operating volume. The burden density is calculated from the solids bulk density, agglomerate packing and the fluid density. Power is calculated using a modified Liddell and Moys correlation for burden position and shape, and the operating drum speed. A further power allowance is made to allow for accretion drop off during drum rotation. Results from the model (especially power and per cent operating fill) have been verified from industrial installations of significant size. Predicted and observed power draws are within five per cent when burden slip and bypassing are not significant. When these are significant (at fills above 15 per cent) the actual power draw will be less than the model prediction. Under these circumstances the quality of the agglomerates will be poor.

Sep 13, 2010

Portable crushing at Duval Corporation's Sierrita open pit mine has proven both the economics and operability of large, hardrock, portable systems. In-house expertise was utilized to create a system incorporating both operational and maintenance features requested by operating personnel. The monitor/control system involves over 400 channels of information and is based on a DEC 1SI 11/2 microprocessor communicating with seven microprocessor-based data acquisition systems over a 4-wire, multidrop link. The year and one-half successful operation affirms the design philosophy and the hardware/software implementation.

Jan 1, 1985

The relationship between the permeability of coal to a mixture of methane and carbon dioxide, and the permeability to methane and carbon dioxide separately is described in this paper, along with the analysis of the differences in permeabilities of coal to methane and carbon dioxide.

Jan 1, 1989

In recent years there have been a number of excellent towns built for mining communities in remote parts of Australia. Planning has been thorough, and very large capital expenditures have been made by companies to provide high standards of accommodation, services and amenities. But so often the phrase 'company town' comes to be applied, expressing the frustrations of the residents, working for a single employer who dominates their lives, and of the company, which would prefer not to have to build and operate a town. The much-vaunted early success of some iron ore, bauxite and coal projects has led to a belief that the success of all mining projects is assured. Those holding this belief ignore the vagaries of mineral deposits and of markets, and the need to amortise large high-risk capital expenditures, much of which is spent on social and industrial infrastruc- ture. This expenditure on infrastructure does not have to be

Jan 1, 1975

This paper reviews the use of MTU diesel engines in uses such as Off-Highway Vehicles, Rail traction, Generating Sets, Marine Propulsion and Defence Applications, and focuses on a central theme of maximum power in the minimum of space.

Jan 1, 1986

By Haartti J

Generally when equipment is chosen for solving a dewatering problem, the equipment is based on one of following physical methods: gravity (sedimentation, screens), vacuum (vacuum drum and disc filters, belt filters), pressure (filter presses, hyperbaric filters) and centrifugal forces (centrifuges). The choice of method and type of equipment depends, among other things, on the requirements on the maximum water content allowed in the filter cake and on the particle size distribution and the concentration of solids in the material to be dewatered. All the above-mentioned equipment has its benefits and drawbacks. The conventional vacuum filters of drum or disc type are of a simple construction with few parts to be replaced, but these filters produce a filter cake with a fairly high moisture content, and a dryer is required for additional drying. In most cases the use of pressure makes it possible to produce filter cakes with the desired moisture content but the equipment is of complicated construction, leading to high maintenance costs . In addition to this the consumption of compressed air is high. The capillary filtration to be described in this article is a dewatering method which combines the benefits of both the conventional vacuum disc filter and the filter press. The capillary filter produces low cake moistures with a machine of very simple construction similar to that of the vacuum disc filter.

Jan 1, 1993

By V Sahajwalla, S Shin

Research activities to classify the quality of iron oxides have a long history but most of such activities are for the existing processes such as blast furnace or DR plant. Therefore the newly developed process, such as the COREX process, needs new standardisation although some basic functions of the new process have similarity to the existing processes. Many researchers (Hauk, 1990; Cho et al, 1998) in the field of COREX process have conducted investigations since the early stages of the process development and activities are underway for further plant optimisation. As Agrawal and Oshnock (1995) pointed out, because coke is not included in the COREX reduction shaft the strength requirement of the feed materials in COREX process will be more demanding than that in the blast furnace. This condition is similar to Midrex DR plant but the main reduction gas of COREX plant is carbon monoxide generated from coal combustion while that of Midrex DR plant is hydrogen from natural gas.

Jan 1, 2000

The able address on the currency question given by the Right Honorable A. J. Balfour, M.P., late leader of the Government, at the Mansion House lately, before a large and influential audience, will strike a key-note that will resound throughout the world. It is high time that gentlemen of position and influence should come forward and express their views on this subject, so as to cause the matter to be,more seriously considered than it has been. The question can be no longer ignored or treated with indifference by bankers, financiers, merchants, miners, and others interested in the settlment on some basis the relative values gold and silver bear to each other. It is gratifying to not that such a great leader of political opinion as Mr. Balfour has given serious attention to this important question.The address created a deep impression ,on the minds of many who probably had not given the matter much att.ention, and Mr. Balfour's words will re-echo over a wide range of thought with such effect that I have no doubt they will materially help to check the downward tendency of the value and uses of silver. As a mining engineer, interested in the development of our mining resources for increasing gold aud silver for currency, and having devoted much attention to the subject, I cordially approve of the views set forth by Mr. Balfouf, and I think the general body of all interested in the production of gold and silver will do the same.

The equipment and general smelter layout for the Mount Isa Copper Smelter were designed by engineers associated with the American Smelting and Refining Company and by Mount Isa staff engineers. The final notice of site was dictated by the need for 'building the smelter near the existing Mount Isa power house to enable full use to be made of the steam from the waste heat boilers. Although much excavation work was necessary before concrete foundations could be poured, the location lends itself to further expansion should it become necessary. The plant is designed and constructed to involve straight line smelting operations which include the following major steps in the overall scheme.1. Charge make-up.2. Roasthig.3. Reverberatory smelting.4. Converting.5. Refining.6. Casting.CHARGE MAKE-UPA system of proportioning bins is provided for preparing the feed mixture for the roasters, Sulphide concentrate containing 24% copper wiil be delivered by belt conveyor from the filter plant to the smelter storage patio. This is a large roofed concrete floor that provides a maximum storage capacity of 8,000 tons of concentrate. Eight proportioning bins located below but adjacent to the south end of the patio will be used for actual charge make-up from which concentrate, ore and flux will be proportioned to the feed belt and conveyed to the roaster feed hoppers. Four of the proportioning bins, 80 tons capacity each, will receive...

Jan 1, 1953

By Torrance AC

A joint research programme conducted by BHP Central Research Laboratories and Du Pont Wesfarmers Pty Ltd examined the effect of the size of cast primers on the run up and steady state detonation veloci- ties of ammonium nitrate based explosives as a function of blasthole diameter. Both continuous and point to point velocity of detonation meas- urement techniques were used. The field trials examined a number of the Du Pont HDP series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the run up velocity of 187mm diameter ANFO charges is negligible using cast primers as small as 150g. owever, emulsion and watergel explosives did exhibit run up in both 187 and 311mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blasthole diameters.

Jan 1, 1988

n One of the most interesting and economically important developments which has .`taken place- in the Kalgoorlie Field over the past twenty .years is the proved penetration of ore into - caicò schist. which:has been established on the North Kalgurli Mine. 'This is quite extensive, both. laterally and ' in -depth, and has occasioned-,'" ccasioned ' " some madification.of geological thought In the search for additional ore sources:. .Ore has been mined in calc schist almost since the' first major: gold::discoveries-were made,. and the principal 'features of the various types of depos:itl are well covered in the literature ' of the field. ' However, occurrences in caic schist have not-been characterised by the same degree of continuity or frequency as the innumerable lode formations in- the more -favourable quartz dolerite, ' and there has been a tendencyAo regard,them as isolated and discontinuous ore bearing structures, occurring only under very special-- conditions. It is not intended-:to describe the whole' range of caic schist ore occurrences in this paper, but only major controlling structures, whose penetration therein has been definitely established, and in which an appreciable .amount.of,_ore.has, been and is still being. found.. . It is considered that -similar stiiictiires: may present a' major objective for future exploratory work in other parts of the field'.

Jan 1, 1964

By Eoffe SW

The wide application of computers in beneficiation plants has resulted in the creation of a number of complex automatic control systems at all stages of ore dressing processes. To create such systems it is necessary to solve complex problems of analysis and calculation. The application of computers to solve these problems demands development of simple and effective methods of investigation and simulation of ore dressing process dynamics because all the known methods are complicated in usage and cannot guarantee the desired accuracy and quality of process control. A new grapho-analytical method of investigation and calculation of ore dressing flow sheet dynamics, worked out by the authors of this paper, is based on proportion method development and is used to construct dynamic characteristics of the investigated processes. It is possible to use the given method for investigating benefication schemes with flotation machines having non-linear static characteristics and circulating loads. The suggested method of investigation of concentration flow sheet dynamics allows us to obtain dynamic characteristics of technological process parameters in both linear and non-linear systems. Moreover, the final result can be obtained without labour consuming analytical calculations by a simple graphical construction based on the static characteristics of the known equipment and processes.

Jan 1, 1993

The writers of these notes, having conducted some tests on the steam consumption of air compressors under varying conditions, believe that the detailed results of such tests will be of interest to the members of the Institute, and may lead to the contribution of further and more valuable information, of benefit both to manufacturers and users of this class of machinery-to the manufacturer in that he frequently has the opportunity of giving a very thorough test to the machine in the shop, and-tothe user or purchaser by making clear to him what may be reasonably demanded of a high-class machine. It must be remembered that, though of the highest importance, a low steam consumption is but one of the many features of a high-classmachine; for the present, however, it has been considered advisable to confine the paper chiefly to the first-mentioned aspect, with such information concerning the air ends as is obtained along with the steam consumption tests. Unfortunately, too few of these tests are conducted, and but few results are published, therefore the writers feel that no apology is needed in bringing their results before the members.Some nine months ago the Brilliant Extended G. M. Co. was supplied with a compressor by Messrs. Thompson and Co., of Castlemaine, and with the object of testing its actual performance.

Jan 1, 1907

The thick coal seams of the South Maitland field are the only ones in New South Wales which have been worked extensively to heights beyond 3.8 m (nominal "thin" seam height). Under shallow cover only minor difficulties were experienced in developing first workings but later the widespread occurrence of incidents of spontaneous combustion and the growth of "creeps" extending over large areas gave the field its own peculiar problems. As the mines have driven under deeper cover extreme difficulties in forming development roadways have been experi- enced. Various methods have been adopted in an attempt to overcome the problems of the field.

Jan 1, 1976

IN the course of his employment the Broken Hill Co. the writer has had occasion to use and instruct others in the use of the Shamrock rescue apparatus. This paper deals with the various types of apparatus tested. The common object of the various types of breathing apparatus is to enable the wearer to remain and work for varying periods of time in an atmosphere which is either deficient in oxygen or is poisonous that is, contains carbon monoxide or irritating and irrespirable vapours, such as the smoke from underground fires, sulphur dioxide or ammonia fumes. For any apparatus to be efficient as required in the above paragraph it must fulfil the following conditions;1. Air-tight as regards the passage of the air from the outside to the inside. In atmosphere containing carbon dioxide a slight leak would not render the apparatus useless; but where irritating vapours, such as the smoke from burning oregon and sulphides, are met with, even the slightest leak must be avoided.2. The oxygen supply must be ample, and so supplied that it is not checked by expiration.3. Expiration and inspiration must not be retarded.

Jan 1, 1911

Robe River Mining manages a large open pit iron ore mine in the Pilbara region of the North-West of Australia. The mine is managed for various joint venture participants.In July 1986, Robe River Mining made various changes to its management philosophy, which were heavily publicised in the media at the time.As a result of those changes to its management philosophy, Robe River Mining has been able to dramatically increase its production output, productivity, and safety performance without having to resort to major capital outlays and without the benefit of restructuring of applicable industrial awards.

Jan 1, 1992

By J-P Franzidis

Industrial flotation plant design is a complex process involving many aspects, one of which is the use of pilot-scale plants to test industrial plant flow sheets. Once test work on a pilot-scale has been performed, scale-up of these results to the full-scale plant must be performed. This paper describes scale-up test work performed on the Floatability Characterisation Test Rig (FCTR). The FCTR is a self-contained, highly instrumented mobile pilot plant designed to determine flotation model parameters and to develop and validate flotation plant modelling, scale-up and simulation methodologies.

Jan 1, 2004

THE manufacture of Portland cement on a commercial basis dates back to the year 1824, when Joseph Aspidin, of Leeds, patented his process. It was, however, only within the past 25 years that the cement of to-day commenced its history, and during that period manufacturers have constantly tried to improve the grade of cement.The introduction of the rotary kiln at the opening of this century was the starting point of rapid development in the process of manufacture, and in the quality of the cement produced.Following on the rotary innovation came the wet process. This at first was used only where the raw materials were of a soft nature; but to-day nearly all classes of materials can be treated by this method. Oompared with the dry process, it allows for greater refinement of raw materials, more intimate mixing, better chemical combination, and economy in fuel. Taking advantage of this, the manufacturers in England and America are in a number of cases substituting the wet for the dry process.Subsidiary machinery throughout the factories, such as crushing and grinding mills, have also been vastly improved. The chemists, too, have done their share in the work. Long and careful research has proved the necessity for accurate proportioning of raw materials, thorough mixing, and very careful burning. All these factors combined have given us the product of to-day, which is consistent within very narrow limits, and far superior to that of the beginning of this cement era.

Jan 1, 1926