Search Documents

By M Hudyma

Open stope mining is the most common mining method employed in underground, hard rock mines in Canada. It is characterised by relatively small, single lift stopes (20 000 to 100 000 tonnes), and fast stope turnaround times. Host wall rock mass conditions, which are typically poor to fair, are the controlling parameter in stope dimensioning. Rock mass stability is maintained by designing all stope surfaces at a stable dimension, and through extensive use of cablebolting for stope backs and frequently stope hanging walls. Dilution control is a high priority. The typically small, high-grade, deep and irregularly shaped orebodies are incrementally developed, usually in a bottom to top direction. In many cases, high stress is encountered due to the depth of the orebodies. Overstressing of pillars and hanging pillars are avoided through the use of pillarless or early pillar recovery mine sequencing strategies. Stopes are invariably filled, and in higher grade and wider orebodies, cemented fill is commonly used. This paper generalises many of the similarities found in Canadian open stope mines.

Jan 1, 2000

Traditionally, the predominant drilling method in open pit mining has been large hole rotary drilling using cumbersome, inflexible equipment offering merely limited scope for improvements in pit design and overall costs. By contrast, the recent development of comparatively light high-pressure down-the-hole hammer crawlers has paved the way for new ideas and trends. High penetration rates coupled with superior mobility and fast set-ups contributing to substantial productivity gains have resulted in a renascence for this drilling method in open pits. The ability to cover a wide range of hole diameters and angles gives designers unique drill pattern possibilities especially when establishing steep and stable pit slopes. As pre-split holes, buffer holes and production holes all can be drilled by using the same equipment, there are, there are obvious advantages in production scheduling as well as in materials handling and service. This paper presents some case stories, which will demonstrate the benefits and improvements that the introduction of new drilling methods and equipment has brought to open pit mining operations.

Jan 1, 2003

The recent installation of top gas temperature probes in blast furnaces at Australian Iron & Steel Pty. Ltd. - Port Kembla, has provided the means for studying radial gas flow distribution in blast furnace shafts. This paper describes the top gas temperature probes and outlines their development and results of initial studies aimed at obtaining a suitable relationships between temperature profiles and furnace parameters. The effects of various combinations of burden materials have been outlined by the results reported. The use of probes has also helped to clarify the effect of casting cycles on furnace operation leading to increased emphasis on the reduction of the interval between gun-up and drill-out. Areas for future studies are also broadly Outlined.

Jan 1, 1975

By Albano C, Antila A, Flykt B

A method for relating operating variables and dewatering parameters of Thunes disc filters in the LKAB pelletizing plant at Malmberget in Sweden, via empirical mathematical models is described. Near orthogonal experimental design was used, where all independentvariables were allowed to span over their domain of variation and pseudo-randomly distributed among the experiments. The dewatering parameters are dependent on many variables and instead of using a traditional mechanistic model, an empirical model based on multivariate data analysis was chosen. The way of expressing the relation is by regression coefficients obtained from partial least square regression (PLS). Two empirical models were generated. The models were validated using an extra set of 56 experiments. The dewatering parameters were related to the design variables with few experiments, and user-friendly response surface methodology was used to determine the optimal conditions.

Jan 1, 1989

By Brown GA

Results are presented which demonstrate the feasibility of employing electrolytic membrane technology to process leach liquors derived from alkaline pressure leaching of scheelite concentrates and to recover and recyle sodium carbonate. Thus the problem of disposal of sodium sulphate is avoided. In a further application of the technique sodium tungstate is converted to tungstic acid which can be further processed by three possible routes to crystalline or amorphous tungstic acid or tungsten powder. In each route sodium hydroxide is produced which on carbonation can be recycled as soda ash to the pressure leach stage. Further testwork is required to determine long term operational conditions in the membrane cell and to confirm the effect and deportment of impurities on products. The process has been patented.

Jan 1, 1986

Gold mineralisation at the Macraes Gold Project is hosted in the Hyde-Macraes shear zone and can be traced for ~30km along strike, although economic resources are confined to a 7 km section in the vicinity of the Macraes township. The shear zone, which typically dips at a low angle (~20 o ) to the NE, is bounded by an upper hanging wall shear and a lower footwall fault. Mineralisation occurs along the hangingwall of the shear zone as well as in low angle concordant shears and stockworks. Ore types include graphitic cataclasites with variable amounts of quartz veining, ælode schistsÆ and quartz-vein stockworks. Rehabilitation at the mine has focused on creating an environmentally benign site dominated by pasture to allow continuation of the traditional pre-mine farming economy. Changing regional economics, continued urbanisation and a reduction in traditional employment opportunities has seen a rethink in the long-term rehabilitation outcomes. The community has recognised that the rehabilitated site will provide the basis of a viable tourism venture and the creation of a Heritage and Art Park (working title æGolden Point ParkÆ) is the culmination of that process.

Jan 1, 2002

By J Zeni

In 2001, the Springvale Coal Mine determined a requirement for a 360 m deep vertical airway to ventilate ongoing underground longwall mining operations. The project, referred to as the Springvale No 3 Ventilation Shaft, was completed in 2003 - 2004 by blind boring a 4.25 m diameter hole from the surface to the coal seam at 360 m depth. The shaft was completed with a 3.5 m inside diameter lining made from a continuous watertight steel and concrete composite pipe. Presented from both the clientÆs and the contractorÆs perspective, the following paper describes the process of constructing a blind bored ventilation shaft for this application. Beginning with the clientÆs definition of the requirements and specifications for the shaft, the paper describes the steps followed by Springvale Coal prior to awarding the contract. Springv aleÆs process involved a thorough site investigation including procurement of geotechnical data for prospective contractors and the management of issues relating to safety, quality and the environment. The clientÆs view is followed by a description of the planning and works performed by their nominated shaft drilling contractor, Ardent Underground Pty Ltd.The contractorÆs description of the works includes the details of the blind shaft drilling and lining construction process used for this application. The design of the shaft lining installed at Springvale Coal was the first of its type to be used in Australia. The successful installation of a watertight composite shaft lining and the safety of the method, which did not require any personnel to enter the shaft or the mine, were among the positive outcomes from the project.

Jan 1, 2005

Published information on technical and market developments in the uses of zinc tends to dwell very largely on two groups of uses of zinc - zinc coatings (mainly galvanising) and zinc casting alloys. These two groups account for two-thirds of primary zinc consumption. However, if total zinc consumption is taken into consideration, coatings and casting account for a little over half the total. Either way, the health - or otherwise - of these 'other' uses of zinc can have a substantial effect on the industry as a whole. The aim of this paper is to put the whole market picture for zinc into better focus, concentrating on the factors which can affect consumption in the 'other half' of zinc's markets: ò brass - the third most important market for zinc at around one million tonnes - responds to changes in the economic cycle. It has seen substantial changes in the balance between different forms of semi products, and, in Europe at least, some real market gains; ò zinc sheet - one of the original uses of zinc in Europe - has grown substantially in some countries, but remains almost unknown elsewhere; and ò zinc pigments and compounds are so numerous that - barring the substitution of zinc oxide in rubber - major overall changes in the market are unlikely. The paper examines these markets and assesses their potential and implications for zinc markets as a whole.

Jan 1, 1993

By D Stow, M Edmondson

Lemington coal mine is operating in an environmentally sensitive area in the Hunter Valley, NSW, Australia. Late in 1999 the southern pit was developed using a series of box cut blasts. After the initial development the area would have been free dug due to the soft, well-jointed nature of the deposit. However, it was decided to trial drill and blast to determine if shovel productivity could be improved to enable an overall mining cost reduction. The initial trial blast results were less than satisfactory with both environmental issues occurring and the desired shovel productivity not being achieved. An audit of the blasts indicated that wet ground and the presence of soft clay inter-bedded with harder rock caused the poor blast results. Also, water-affected explosive product combined with explosive energy loss into soft ground led to flat spots and tight digging in the hard band areas, resulting in the lower dig rates. Lemington Mine and Orica Explosives developed a plan to match the rock with the appropriate explosive type and energy. This resulted in a number of blasts over a six-month period using a new non fuming explosive product, æNovaliteÆ. The results have been excellent with the environmental issues being totally resolved and dig rates improved, enabling reductions in mining costs. This has allowed the mine to continue with their exemplary record of environmental management whilst achieving operational efficiencies.

Jan 1, 2001

By E Mofya, R Kaunda, P Lever

One of the fundamental requirements for being able to optimise blasting is the ability to predict fragmentation. An accurate blast fragmentation model allows a mine to adjust the fragmentation size for different downstream processes (mill processing versus leach, for instance), and to make real time adjustments in blasting parameters to account for changes in rock mass characteristics (hardness, fracture density, fracture orientation, etc). A number of blast fragmentation models have been developed in the past 40 years such as the Kuz-Ram model (Cunningham, 1983). Fragmentation models have a limited usefulness at the present time because:The input parameters are not the most useful for the engineer to determine and data for these parameters are not available throughout the rock mass. Even if the input parameters are known, the models still do not consistently predict the correct fragmentation. This is because the models capture some but not all of the important rock and blast phenomena. The models do not allow for ætuningÆ at a specific mine site. This paper describes studies that are being conducted to improve blast fragmentation models. The Split image processing software is used for these studies (Kemeny, 1994; Kemeny et al, 1999).

Jan 1, 2001

All companies and individuals who embark on a business venture incur costs. For the most part these costs can be conveniently categorised, firstly into capital and operating costs and then into the various elements of these major cost centres. Although the nature of expenditure naturally differs as between industries certain broad cost types are characteristic of all heavy industries. The capital costs of gaining access to an orebody, equipping a new mine, building a treatment plant and perhaps refining and smelting facilities are likened to capital expenditure by a manufacturer on new plant and equipment required for an expansion or new product innovation. Similarly the day to day costs of labour and materials employed in the running of a mining operation can be likened to similar costs in other heavy industry. There is another group of costs that are not so easily categorised. Most industries incur unavoidable costs that do not form part of the direct or capital costs of physical production. These costs include taxes and other payments to government and research expenditure. The mining industry has a particularly heavy burden of non-production costs and it is the objective here to highlight and analyse a few of them. These costs are exploration expenditure, infrastructure expenditure, royalties and income tax. This is not to suggest that these are the only major non-production costs that the mining industry needs to bear. The industry may incur significant costs for environment protection, land tenure maintenance and on liaising with Government on a wide variety of matters. It is for reasons of subject manageability that the list is confined to the four costs mentioned. For the mining industry, exploration and infrastructure expenditure, royalties and income tax have several distinguishing features. Firstly, they are generally proportionately large costs. Exploration and infrastructure expenditure for example, could well exceed mine development costs. Depending on how royalties are levied, they may be very high in relation to profits earned and many in fact exceed profits. Secondly, except for income tax, they are costs that are generally not payable by other industries. Exploration expenditure is in some respects comparable with industrial research and development. However, because mines are wasting assets exploration is necessary for survival, and it is likely to form a larger part of costs per dollar of profits or sales than R&D. It can therefore be said that exploration is of far more significance to the miner than R&D is to the typical industrial company. Furthermore, unlike exploration expenditure, R&D results are transportable and patents permitting, transferable. The infrastructure burden that miners must carry is unique to the industry. Whereas urbanised industry is not usually liable for the capital cost of power, water, transport, townships and community facilities, the miner must finance these projects himself. Neither the payment of royalties, nor of course, income tax are unique to the mining industry. Royalties are more properly described as a unique charge on some primary industries but however described, they are a charge that manufacturing and service industries do not have to pay. Whilst we all pay income tax, the mining industry's uniqueness derives from the special problem that the industry has in arriving at annual net income in view of the capital intensity of the industry, partly due to expenditure on infrastructure, the indefinite life of capital equipment and its unpredictable residual value, funds expended on exploration and long lead times associated with a mine development. The third distinguishing feature of these costs is that, with the possible exception of exploration expenditure, they are heavily influenced by the policies and actions of Government. As such the industry has a responsibility to promote the industry by emphasising its potential to improve national product including exports and by requesting that the Government provide for the industry in its long term planning and seek its co-operation to prevent the industry incurring inequitable penalties relative to other industries.Finally, exploration and infrastructure expenditure are significant because they are front-end charges on a project. When due allowance is given the time value of money and the deferment of income from a mining development to which they relate, exploration and infrastructure expenditure assume greater importance than the raw money expenditure suggests. For all these reasons, exploration and infrastructure expenditure, mining royalties and mining income tax are worthy of detailed study. This is the purpose of this paper. The objective is to examine the determinants that give rise to them and provide some thoughts on their impact on on-going and potential mining developments and, where relevant, to make some suggestions as to how they may be minimised.

Jan 1, 1977

The Wellington Dam catchment has high value water, agriculture and coal and power generating resources. These conflicting land uses are managed through consultation and regulation. The Wellington Dam catchment is unique in that the Collie Coal Basin is located almost to the edge of the dam and has coal mining and power generation as its primary land use. Currently the dam is only used for irrigation due to its high salinity. The State Government has committed to reduce the damÆs salt levels to below 600 mg/L by 2015 so that it can be considered for public drinking water supply. The coal industry in conjunction with the community and State Government has worked together to enhance the water quality within the Wellington Dam to maximise its value and use by using mine dewater for industry, diverting saline Collie River flows, providing environmental (social) flows and enhancing water quality of mine voids to encourage new industry to the Collie Region. Both surface and groundwater in the coal basin are generally fresh, whereas the salinity in the Collie River East Branch generally ranges between 3000 to 20 000 mg/L and 1700 to 10 000 mg/L in the South Branch. Mine dewatering is currently two to three times greater than the recharge to the coal basin. As a result, all mine dewater is sent to power stations in the area, with excess discharged into drainage lines which flow into the South Branch of the Collie River. To maintain environmental and social flows some groundwater is also pumped to the South and East Branches of the Collie River during summer months. Completed mine voids are used for recreation and options for aquaculture are promising. However, handback criteria are yet to be finalised.

Jan 1, 2006

By T Davis

Cameco Corporation operates the high-grade 140 tpd fly-in/fly-out underground McArthur River Uranium Mine in Northern Saskatchewan in a joint venture with Cogema Resources Inc. Reserve grade is in excess of 20 per cent U3O8 with current mining grade averaging 16 per cent U3O8. Due to the high radiation potential of the ore, the non-entry mining method of raiseboring was chosen to minimise worker radiation exposure potential. The raisebore and extraction horizons are located in waste rock with the orebody located between horizons. Ore produced by raiseboring is delivered by LHD to an underground SAG mill and is then hydraulically hoisted to surface receiving facilities after underground thickening to 50 per cent solids by weight. Concrete backfilling is utilised. The orebodies at McArthur River are adjacent to water bearing sandstone. Ground freezing is therefore employed to isolate the ore from this water bearing ground. Calcium chloride brine at -35¦C is circulated through a series of cased boreholes to establish freeze walls up to 25 metres in thickness. At 18 000 000 lb of low cost U3O8 production per annum, McArthur River ranks as the worldsÆ largest uranium mine. Over 50 per cent of the workforce resides in this sparsely populated area of Canada with approximately 40 per cent being of aboriginal ancestry. Site operations must cater for winter temperatures as low as -50¦C.

Jan 1, 2002

By B H. Yin, S Mendoza, M Nusheh' C W Bumby, A Zhang

Hydrogen-direct-reduction of iron ore in a vertical shaft furnace is a potential process that could significantly reduce CO2 emissions from the steel industry. This approach requires the pelletisation of iron ore fines, which then undergo high temperature induration to strengthen the pellets before they can be fed into the shaft furnace. Here we report on investigations into the disc-pelletisation behaviour of New Zealand titanomagnetite ironsand, and its subsequent induration and hydrogenreduction behaviour. Initial studies focused on the effect on pellet strength of varying ironsand particle size and induration conditions using bentonite and a commercially sourced carboxymethylcellulose binder. Green pellets formed with ironsand of average particle size of 65 μm exhibited optimal strength. The compressive strength of these pellets after induration at 1200°C for 2 hrs in air was measured to be 976 N. Interparticle bonding within the indurated pellets occurs due to a combination of titanohematite recrystallisation (from oxidation of titanomagnetite), and the formation of a liquid bonding phase due to interdiffusion with the bentonite and subsequent melting. Further investigation with various binders showed that a combination of both organic and inorganic binders was essential to achieve optimal pellet strength. Carboxymethyl-cellulose binders provides green strength, whilst inorganic binders such as bentonite promoted high indurated pellet strength. Hydrogen reduction tests in a thermogravimetric furnace showed that all the pellets could achieve a maximum reduction degree of 97 per cent at 1100°C, indicating that the different pellet preparation procedures had no significant effect on reducibility. Pellet recipes developed in this work are now being used to investigate vertical shaft hydrogen-DRI processing of NZ ironsand in a kg-scale laboratory reactor.

Sep 18, 2023

By Y Wei, H-B Mnhlhaus

Particles are by far the easiest objects to simulate, because their dynamics is simple. Determining the motion of particles and their interaction, a wide variety of deformable structures can be constructed by connecting particles that have mass, position, and velocity, and that respond to forces. Starting from this simple idea we have derived what we call the particle-lattice method for the solutions of boundary value problems of deformation and fracture of solid mass. The problem of rock breaking by blasting operations as well as fracture and flow of rocks fragments involve momentum transfer between solid and fluid; gas flow and reactive mass transfer. In this paper we outline the method and describe briefly the salient features of the algorithm. We derive relationships between the contact properties for the discrete model and the properties of the underlying continuum and fluid flow coupling procedure. Finally we illustrate the potential of the method by means of example solutions related to the dynamic fracture and flow in jointed rock by blasting.

Jan 1, 1999

By W A. Take, M McKellar, A Walsh, S McDougall, S G. Evans

Recent tailings dam failures have heightened public awareness of the hazard posed by storage facilities for mining waste, illustrating the need for a more critical examination of tailings dam breach mechanisms and the potential mobility of liquefied tailings. Knowledge from tailings dam breach studies will help improve safety and risk management through more accurate inundation maps, dam consequence classifications and emergency preparedness plans. Tailings dams differ from conventional water retaining dams, although dam breach relationships used in practice rely heavily on relationships derived for breach processes from the latter. Physical modelling offers a controlled environment to advance the understanding of tailings dam breach processes, thereby allowing for modelling of simple geometry and boundary conditions to test hypotheses. The performed experiments investigate prototypical tailings dam configurations and material behaviour, with the objective of validating numerical models that will enable practitioners to better assess and mitigate tailings flows resulting from tailings dam failures. Research conducted in the Queen’s University Landslide Flume at the Coastal Engineering Laboratory has investigated the breaching of 1 m high dams with tailings geometry by overtopping initiated by a v-notch incised in the dam crest. This paper presents the initial results of the next stage of this research comparing the outflow hydrograph following loss of containment caused by shear failure to overtopping initiated by notch flow. The two dam experiments presented are constructed with similar dam and reservoir geometries allowing for a direct comparison of the effect on the outflow hydrograph of each failure event. Preliminary outcomes suggest that although both dam failure events are triggered from separate mechanisms their geometries allow for similar values of Q_peak to be reached. Future work is currently planned to expand the shear test series to explore the influence of failure mechanism on the outflow hydrograph.

Jul 1, 2021

By K Williams, G M. Evans, S M. Iveson, K P. Galvin, C E. Loo

The Australian Research Council (ARC) has recently established an Industrial Transformation Research Hub in the area of iron ore, focused on iron ore characterisation, beneficiation, materials handling and end-use functionality. The research hubs are part of a new initiative aimed at building stronger relationships between industry and universities, while addressing issues of national significance. The ARC Research Hub for Advanced Technologies for Australian Iron Ore will focus its attention on developing innovative approaches for creating enhanced value across the full value chain through the characterisation of different ore types, beneficiation and materials handling and transport. This hub brings together five industrial organisations and a research team formed from well-established research groups based at the Newcastle Institute for Energy and Resources. These groups have a record of working closely with industry to create opportunities. Examples include new beneficiation technologies such as the Reflux Classifier for achieving gravity separation, the expertise of TUNRA Bulk Solids in materials handling and the Iron Making Centre at Newcastle, which is a capability maintained by BHP Billiton following the closure of its Technology Centre in 2009. The purpose of this paper is to provide an outline of the research hub and its objectives, some background on the research groups that now form the hub and an insight into the strategy adopted for developing and implementing new technologies. The paper also describes a range of novel technologies that have the potential to be developed and applied to iron ore beneficiation.CITATION:Galvin, K P, Roberts, A, Loo, C E, Evans, G M, Williams, K and Iveson, S M, 2015. Australian Research Council research hub for advanced technologies for Australian iron ore – an introduction, in Proceedings Iron Ore 2015, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D Chalmers

After the sustained use of the GAG (Górniczy Agregat Gaśniczy) engine at a Queensland coalmine, it has raised questions as to its effectiveness as a remote firefighting tool. All firefighting apparatus have advantages and limitations, however the deployment of any apparatus must be based on its likelihood to succeed and effectively extinguish the fire or bring it under control. A recent study conducted for ACARP by researchers at UNSW has highlighted that there is more to be learned about the GAG. As coalmines are mining at greater depths and fan pressures are much greater than they were when the GAG was introduced, deploying the GAG may be a total waste ofresources and may place operators at greater risk. When the GAG unit is positioned on the surface of the mine, the pressure it generates has to overcome buoyancy of the exhaust gases and the frictional resistance of the borehole and part of the mine circuit. Buoyancy in deeper holes can lead to the GAG pressure relief system opening, venting out the products to the atmosphere without delivering any product to the mine workings. Additionally, frictional resistance is a function of distance. Deeper holes will have a greater frictional resistance than shallow holes. Delivering sufficient products from the unit will be limited by the available pressure that has to overcome the buoyancy, and increased mine resistance thatconsumes any residual pressure. By documenting the limitations of this unit it will enable better decisions to combat a fire or spontaneous combustion event.

Oct 12, 2022

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By K Le Bron

Fatalities that occurred because of rock falls in off-reef excavations (excluding shafts) over the last three years range between ten per cent and 20 per cent of the total number of fatalities that have occurred due to rock falls in the South African mining industry. These rock falls, mostly exacerbated by blasting practices, occur because of failure on discontinuities within the rock mass. Among other reasons of their occurrence is insufficient support installation or the incorrect assessment of rock mass conditions. This report presents qualitative analysis intended to outline rock stability conditions in tunnels subjected to dynamic loading. Seismic waves including those created by firing an explosive charge in tunnel rocks are considered. The rock behaviour is monitored using geophones and extensometers variably installed to record the near and far effects of roof bolt support units on a dynamically loaded rock. The paper discusses the results of field investigations.

Jan 1, 1999