Search Documents

By Denholm W. T, Rankin W. J

The reduction of zinc from lead blast furnace slags using hydrogen was studied at 1300¦C as part of a laboratory investigation of zinc fuming. To perform the experiments, 300 g "spent slag" was melted in a crucible. Hydrogen was then injected into the slag through a lance and fresh blast furnace slag was added regularly in small quantities over a period of 40 minutes. Zinc added in the fresh slag was reduced and the zinc level of the bulk slag attained a steady state value of between 1 and 9% after about 10 minutes, depending on the gas injection rate. Because of the high reactivity of hydrogen, bulk supply of hydrogen to the slag was the rate limiting step at the flow rates used and it is believed that the gas-slag reactions in the system were at equilibrium. A partially/stabilized zirconia cell with a Ni/NiO reference electrode was immersed in the slags during the experiments and the steady/state oxygen potentials of the slags were measured. By using the experimental oxygen potential values and calculated values of the steady state concentrations of zinc in the offgas, the activity of ZnO in the slags was calculated from the Gibbs's free energy change for the reaction:

Jan 1, 1989

The Lake Rotokaua sulphur deposit, near Taupo, New Zealand, is a lacustrine sedimentary ore body, 220 acres in area and from 7 ft to 96 ft thick, containing, within the area drilled to date, some 20 million long tons of ore averaging 25% elemental sulphur in unconsolidated tuffaceous diatomaceous clay, overlain by about 120 ft of pumice sand and by the shallow Lake Rotokaua. An additional amount of perhaps 4 million tons of sulphur is regarded as probable in the area remaining to be drilled. Current economic studies cover the problems of mining an unconsolidated water-saturated formation with some residual thermal activity nearby; conservation and restoration after mining in a scenic recreation area; beneficiation of the ore and extraction of high- purity sulphur, principally for fertilizer manufacture. The deposit has additional importance as a pointer to possible further discoveries in the Thermal Region.\

Jan 1, 1971

By Rajan S, Mainwaring P, Gould WD, Beaulne M

Polished discs of a complex sulphide ore were leached with three lixiviants; a mixed culture of Thiobacillus ferrooxidans and Thiobacillus thiooxidans, Thiobacillus ferrooxidanalone, and ferric sulphate. At either one or two week intervals the discs were examined by scanning electron microscopy, and the amount of soluble metals released from the discs were determined. The mixed culture solubilized more Cu, Zn and Pb than did either ferric sulphate or T. ferrooxidans alone. However, no differ-ences were observed between the three treat-ments by scanning electron microscopy during the first 44 weeks. The minerals were attacked in the following order: pyrrhotite, cubanite, sphalerite, pyrite and chalcopyrite.

Jan 1, 1990

By Bhattacharyya AK

With increasing demand for more efficient production from the underground coal mines in the Southern Coalfields- of New South Wales, their design and operational aspects are constantly being reviewed and improved. One key area in such pursuits is the reliable design of stable and yielding pillars. The current designs of pillars based mostly on experience leads to unnecessary sterilisation of coal or strata control problems. To explore such mine design problems, computer based modelling is increasingly being applied. In the study described in this paper, the object was to determine the particular width of pillars separating three roadways in a panel at which the pillars yielded completely and their loads largely transferred to the unmined coal at the flanks of the panel. This was approached through a computer simulation of the behaviour of the strata around a panel, in which the three roadways were separated by pillars of progressively decreasing width. A computer program called FLAC based on the finite difference method was used to simulate the relevant strata behaviour in vertical sections. The appropriate in situ values of the deformability parameters relating to the coal seam, roof and floor were determined from the back analysis of some displacement measurements in such a panel. The process involved successive modelling of a vertical section through such a panel,starting with realistic values of the parameters and varying them until the measured and the modelled displacements agreed closely. Based on the results of the numerical modelling, the width of a yielding pillar for the given conditions is Suggested.

Jan 1, 1992

By Pala J

The Ellalong Colliery has been the first to mine the Greta Seam using the longwall method. Analysis of data from geotechnical monitoring has pointed to the role of the strong, massive sandstones of the Branxton formation in the development of loads on the powered supports and pillars. Failure of the sandstone intermediate-roof has been related to first-weight and periodic weighting, measured on the supports, using simple "voussior" analysis. Stress changes, including triaxial components measured in the barrier and chain pillars, have been compared with 2- and 3- dimensional numerical models. The applicable range of the models for the prediction of pillar loads under the strong roof is discussed.

Jan 1, 1986

Peko Mines, a Division of Peko-Wallsend Operations Limited (PWOL) has operated several small underground mines in the Tennant Creek district of the Northern Territory supplying ore to a central treatment plant. The Argo Mine is the most recently developed by Peko Mines. A magnetic anomaly was identified from low level airborne magnetics in 1960 and drilling, which commenced on the site in 1969, was halted in 1974 and resumed in 1980 following the rise in the price of gold. By mid 1983 a resource of + 200 000 tonnes of 12 g/tonne Au had been outlined and a decision to develop the resource was taken following the drilling of three further diamond drill holes which did not significantly alter the value of the resource. The small size of the orebody could not support the full capital cost of two shafts and a single entry mine plan was developed to extract the ore at a rate of 15 000 tonnes per month and to provide all the safety features, ventilation systems and services of a two shaft mine. In December 1983 a contract was let to Allied Constructions Pty. Limited (Allied) to sink and equip a 4.8m shaft to a depth of 410m and to convert the headframe and winder, which are leased for the life of the mine by PWOL from Allied, from a sinking to a production configuration. Shaft equipment designed by Hardcastle & Richards Pty. Ltd. (H & R) in conjunction with PWOL includes a skip/cage, counter- weight, and an auxiliary cage on rope guides, a sealed ladderway and exhaust air ducts.

Jan 1, 1986

By Robertson A. D C, Cranfield L. C, Murray C. G

Most base and precious metal mineralisation in the Gympie Province is genetically linked to intrusion of branitoids of Late Permian to Late Triassic age. Most lodes are hydrothermal quartz and quartz-calcite veins at intrusive contacts, within either the granitoids themselves or the country rocks, and commonly associated with dykes. Other types of intrusive related deposits are disseminated porphyry type Cu, base metals in skarns, and Mo in quartz pipes and veins. Although the Late Permian-Late Triassic granitic intrusives can be subdivided in terms of age, it is not yet possible to relate deposits of particular metals or styles to granites of a specific age on a regional scale.Some significant mineralisation is not associated with granitic intrusions. This includes the Gympie goldfield, by far the largest known deposit within the Gympie Province. Gold occurs in quartz veins crosscutting Early Permian volcaniclastic sediments and also in NW striking fault zones. The source of the mineralisation is unknown. Gold and silver also occur in epithermal, disseminated and breccia hosted deposits within Late Triassic continental volcanics. Epithermal Hg mineralisation at Kilkivan may be related to Early-Middle Triassic volcanics.

Jan 1, 1990

By Grey D, Turner R, Capsanis J

Coal fines are recognised to have a major impact on the cost and efficiency of the recovery of saleable coal. Fines affect the productivity of the whole mining cycle because of the low yields obtained in washing this material as well as affecting the moisture content and handling characteristics of the final product.In 1990, Coal and Allied Hunter Valley Mine initiated an internal study into coal fines based on the assumption that a reduction in fine coal in ROM material will lead to increase yields in the preparation plant. The initial results of this study indicated that the level of fines in the ROM coal can be reduced by more than 40 per cent by simple changes in blast design and implementation.

Jan 1, 1992

Misima Mines Pty Ltd (MMPL) operates a large open cut gold mine on Misima Island in the Louisiade Archipelago in Papua New Guinea. Misima Island lies approximately 600 km east-south-east of Port Moresby. The island is 40 km long by 10 km

Jan 1, 1994

By B Siddall, A Gunstone

The use of a partial secondary crushing circuit provides a flexible way to optimise existing SAG comminution circuits limited by rock competency or enables optimal processing of an ore through second hand equipment not specifically selected for that ore. This paper details the process involved in designing a partial secondary crushing circuit using the recent installation at Mt Rawdon Gold Mine in Queensland as an example.

Jan 1, 2004

The financing of mineral ventures is usually supported by the valuation of a mineral asset, the physical size and composition of which have been determined within quantified limits of accuracy in order that the lending or investment risk can be assessed. The Resource or Ore Reserve estimation is the measurement of that asset and may be the outcome of complicated processes of interpretation and estimation requiring an extensive knowledge and understanding of the general nature of ore occurrences, and of the particular deposit under review. In arriving at an interpretation of the nature and physical distribution of minerals in a deposit, observations may only be available from widely spaced samples and geological knowledge and principles are of prime importance. Consultants may be asked by the lending or investing body to "provide comfort" on the quality of the Resource or Reserve estimations and providing such comfort casts substantial obligations of diligence on the consultant.

Jan 1, 1990

By Jelenich L, Murray J. Rantanen J

The experience gained in the development of an Operator Guidance System (OGS) for on-line process control and fault diagnosis in a commercial scale sintering process will be discussed in this paper. The OGS development started with the specification of feasible control and support tasks, eg ratio control scheme, mass balance calculations. Next, minimum requirements for fault diagnosis and process control were defined and the adequacy of existing instrumentation was assessed. The OGS knowledge base consists of both quantitative and qualitative diagnosis methods. Quantitative models based on fundamental engineering principle are used first and any gaps in such quantitative knowledge are then filled with heuristic rules. The diagnostic rules for the knowledge base was developed based on the knowledge acquired from experienced operators and operations engineers and validated with plant data. A real time reasoning program was written using C language and data base software. The OGS has a human-computer interface which is the primary means of interaction between the OGS and process operator. The OGS development has been successful in assisting operators in decision-making in their routine tasks. Further enhancement to the existing system is currently underway.

Jan 1, 1995

The firing of mass blasts at Isa Mine is a normal operating practice. Both electric and non-electric initiating systems are being used for this purpose. The advantages gained by large firings relate to the Planning, Scheduling, Services and Production functions of Isa Mine. More efficient us"e is made of manpower due to the concentrated charging effort and con- tinuity of the charging operation. In addition, the requirement for ring firing personnel to work at the edge of large stope voids is reduced. Better fragmentation results from the interaction of adjacent detonating rings of blastholes and in flight collisions. With mass blasts there is also less chance of large blocks of ore, created by faults or joints, falling into the stope and creating problems at the drawpoints. The formation of a large tonnage of broken ore facilitates production at scheduled rates from that stope source. The weight of explosive detonating during a mass blast can be considerable. Isa Mine has achieved satisfactory blasting results without excessive ground vibration levels and present knowledge indicates that pillar ground stab- ility has been maintained.

Jan 1, 1978

By Turco E, Pelizza S, Vona A

Within the project against pollution in the Gulf of Naples (Italy) it was envisaged to build a sewage collection tunnel whose tunnelling section is about 30 m2 and whose length is over 4 km. The formations to be bored through feature heteregeneous volcanic deposits made up of either lenses or lava, lapilli and pozzolan layers and ashstone silts. The cover ranges between 10 and 30 metres. The surface is heavily built-up requiring then an accurate monitoring and reduction of noise, vibrations and settlements. The building of the tunnel is therefore carried out by means of a boom tunnelling machine equipped with a mechanized shield. Support along the complete excavation perimeter is provided by linerplates together with an immediate cement grouting behind them. At a later stage the concrete lining will be cast in place.

Jan 1, 1987

By Zhao JC, Chen JJJ

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions.

Jan 1, 1995

Detailed observations were made for two existing continuous miner and shuttlecar systems. A simple model for the shift average cycle consisted of three time components - delays, mining and transport. Cycle improvement and productivity improvement factors are derived and used to predict the theoretical improvement which the observed cycles could achieve. Various strategies of action ranging from short-term optimisation through to long-term planning for continuous haulage systems are evaluated. High potential for improvement is shown for a wide range of operating conditions. An overview is presented for systems, currently available or under active development, which can accept coal directly from continuous miners and offer continuous haulage to the surface. Systems are broadly classified as mechanical-roof mounted, mechanical-floor mounted and hydraulic transportation.

Jan 1, 1982

By Wasserman A. D

Methodological approaches and in- vestigation results are considered in the paper of heatmass transfer processes when harmful impurities are scattered and remo- ved from chamber-like workings, of the air distribution in complicated ventilation sys- tems and of chemical conversion of exha- ust gases in mine atmosphere when diesel equipment is operating. The results presented in the paper are the base for creation of the automatic design, control and regulation of the venti- lation processes.

Jan 1, 1988

By Kellerwessel H, Oberheuser

Since its invention by Professor Klaus Schonert of the University of Clausthal, Germany, high pressure rolls comminution has attained near total acceptance as the preferred method of size reduction in the cement industry. Over 300 units have been manufactured worldwide. At locations where the system has been installed, considerable energy savings have been realised. These energy savings are generally in the range of 20 to 30 per cent compared to conventional ball mill circuits. However up to 50 per cent power saving has been achieved at some installations. This technology, with the exception of the diamond industry, has up to now had only limited success in ore processing. This has mainly been attributable to the abrasiveness of ores encountered in this industry leading to high wear rates. These high wear rates have given rise to an unacceptably short life time of the wear surface of the rolls, requiring regular replacement. A new wear surface has been developed which has shown to give a ten-fold increase in service life over conventional surfaces. This, together with developments made in machine design now give the units the ability to attain the high availabilities demanded by the mining industry, and therefore to allow this industry to achieve the considerable operating cost savings offered by the high pressure rolls.

Jan 1, 1992

In mineral asset valuation the use of any valuation method requires the input of competent and independent technical professionals. A resource valuation must be as transparent as possible to allow others to assess the validity of their underlying assumptions. Materiality is a dominant factor in all valuations and a valuer should set out the basis for the subjective decisions made in this regard. Any valuation methodology must comply with the requirements of the law, practice notes and guidelines issued by the various relevant authorities and professional bodies. The valuation methodology chosen to value a mineral asset depends upon the amount of data available on that asset and the reliance that can be placed upon those data. Mineral assets generally fall into one of three broad categories, depending upon their state of development, ie whether they are at the exploration, development or operating stage. Naturally there are transition phases. Hence, there are ""Grass Roots"" Exploration Areas and Advanced Exploration Prospects; Pre-Development Projects and Developing Mines; and Operating Mines. The features of each of these mineral asset status categories are described, mainly in terms of the confidence in the contained identified Resources/ Reserves. The various subjective methodologies available for the valuation of ""Grass Roots"" Exploration Areas and Advanced Exploration Prospects -are specifically reviewed. The pitfalls in adopting a ""recipe"" approach are noted. It is the author's view that the Expected Value Method (based on the probability adjustment of the output of a Discounted Cash Flow/ Net Present Value model) has little application in the valuation of exploration mineral assets, so it is only briefly addressed. The methodologies reviewed are listed below. ò Multiple of Exploration Expenditure Method (expenditure based). ò Joint Venture Terms Method (expenditure based). ò Geoscience Rating Methods (eg Kilburn - area based). ò Comparable Market Value Method (real estate based). ò Rules of Thumb (eg $/Resource or production unit; % of in situ value). Some recent Prospectuses are used to provide examples of their misinterpretation and misapplication.

Jan 1, 1994

Electronic Detonators have made significant strides over the last few years, both in quality of product and performance in different blast applications. The precision and flexibility of the SMARTDET units provides the mines with a powerful means of controlling blast results, giving both cost and productivity improvements. The SMARTDET Electronic Detonator System, robust and easy to use, has been successfully deployed over the last 18 months in improving mine productivity and creating safer working conditions in both quarrying and long-hole stoping. The key to the improvements has been the precision and flexibility of the electronic timing, and the ability of the mine personnel to grasp the concept quickly and use it effectively.

Jan 1, 1999