Search Documents

By R Dimitrakopoulos, I Minniakhmetov

Geostatistical simulation techniques are used to quantify uncertainty of spatial attributes of interest describing mineral deposits, petroleum reservoirs, hydrogeological horizons, environmental contaminants and so on. The majority of existing methods consider second-order spatial statistics and Gaussian processes, while the more advanced multiple point-based simulation approaches are algorithmic and do not consistently account for the high-order spatial relations in data. Recently, simulation techniques for complex and non-Gaussian spatially distributed variables have been developed, based on high-order spatial cumulants, and make no assumptions on data distribution or require data transformations. In this paper, the previous developments are extended and a new approach for the joint simulation of multiple correlated variables using high-order spatial statistics is proposed. The technique is based on a new algorithm for the decorrelation of correlated variables into factors, using the so-termed diagonal domination condition of high-order cumulants. The decorrelated factors are then simulated using high-order simulation and back-transformed into the initial correlated variables. The decorrelation using diagonal domination of high-order statistics is tested with a data set from a multielement iron ore deposit, and then a fully known two-dimensional data set with two correlated variables is used to demonstrate the practical intricacies of the proposed method.CITATION:Minniakhmetov, I and Dimitrakopoulos, R, 2014. Joint simulation of correlated variables using high-order spatial statistics for orebody modelling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 53–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J J. McNee and, J Crusius, T F. Pedersen

The use of water covers is a globally-applied method for minimising acid rock drainage (ARD) and metal leaching. Although the subaqueous disposal of potentially acid-generating materials has been shown to effectively limit ARD, under certain scenarios, metal remobilisation can occur at circum-neutral pH. The following paper presents data from four case studies in which metal mobility from submerged mine waste resulted in degradation to water quality in the overlying water cover. Subcentimetre resolution profiling of dissolved constituents across the tailings-water interface (dialysis arrays), in conjunction with mineralogical information, were used to elucidate the controls governing metal mobility. The data illustrate four pathways of metal remobilisation, including: the release of zinc via the oxidative remineralisation of metal-rich organics at the tailings-water interface; enhanced remobilisation of arsenic as a result of anthropogenic eutrophication; the release of copper resulting from the pH-driven dissolution of treatment sludges; and the release of radium from uranium mill tailings due to the dissolution of radiobarite [(Ra,Ba)SO4] by sulfate-reducing bacteria. The results highlight the conclusion that the chemical stability of submerged tailings reflects both: the solid-phase characteristics of the tailings material; and the physical, chemical and biological characteristics of the depositional environment. In particular, the data illustrate that rigorous characterisation of both the waste solids and receiving environment must be performed in order to assess their compatibility. The results have relevance to the management of tailings repositories including constructed impoundments, pit lakes and natural lakes.

Jan 1, 2003

Christmas Island contains large deposits of phosphate minerals varying from high-grade calcium-phosphate (apatite) to lower grade iron and'aluminium phosphate (crandallite/millisite). The surface material is dominantly C-grade (Fe/Al) phosphate profiling into B-grade, a variable mixture of C- and A-grade ores, before reaching the high A-grade phosphate (apatite) which overlies a limestone Karrenfeld Base formation. A-grade ore is the basic phosphate used for the manufacture of superphosphate and phosphoric acid, whilst B-grade contains amounts of iron and aluminium which are unacceptable for these acidulation processes. Research into methods of separating the finer iron and aluminium phosphates from the coarser calcium phosphates has led to the development of wash-screen processes enabling recovery of 50 to 60%, as A-grade phosphate. Developmental stages included laboratory investigations, mineralogical studies, pilot tests leading the initial 20 tph prototype production unit and the current 100 tph production wash/screen plant, commissioned early in 1970 at Christmas Island.

Jan 1, 1971

In a previous study, various pyrite depressants were examined to improve the flotation performance of a copper-sulfide ore. Optimal results from this study were used to examine the effect of elevation on recovery and grade. Tests were conducted at elevations of 3350, 1735, 610 and -760 metres, consisted of five repetitive experiments for statistical analysis, and were performed both with and without airflow control. Tests were also performed in a glove box at Montana Tech to mimic the pressure conditions. Results indicate that both recovery and grade are dependent on pressure via bubble size and airflow suggesting that pressurised flotation cells should be considered for operations, particularly those at high elevation. Economics are extremely favourable for implementation because ensuing capital expenses are inconsequential with minimal time for return-on-investment.

Jan 1, 2005

By J E. Everett

Ore selection is generally a highly subjective task, with emphasis on producing product with a consistent target grade matching a perceived market requirement. A composite selection criterion ‘Comp’ (a linear function of the grade vector) can be used to maximise ore tonnage at a specified target grade (in Fe and contaminants) extractable from a block model. The blocks correspond to the selective mining units, with grades interpolated from diamond drill hole data. An iterative procedure has been developed to identify the coefficients and cut-off value for the composite function ‘Comp’, maximising potential ore tonnage at target grade.Commonly, target grade is predetermined by marketing; however, there is no guarantee that maximising ore tonnage at a specified target grade maximises the potential value of the mine. If the value of ore could be expressed as a linear function of the grade components, then these coefficients would be appropriate for the selection criterion ‘Comp’. The cut-off value for ‘Comp’ would correspond to the marginal cost of production; all blocks with a ‘Comp’ score above the cut-off would be classified as ore; and the cumulative grade of these ore blocks would be the average product grade over the life of the mine.Unfortunately, no such value function for iron ore is generally available. Methods for estimating the value function are discussed, using the spot price and sensitivities based either upon operational tolerances for Fe and the contaminants or upon published price differentials. This approach has been applied to an anonymous Pilbara deposit with about one million blocks averaging 1.1 kt. It is shown how the optimal target grade, cut-off grade and maximum tonnage can all be explored as a function of marginal cost and iron ore price. Alternatively, given marginal cost and an iron ore price, the effects of changing the tolerances (and therefore the relative costs of the contaminants) can also be explored.It is suggested this procedure can enable informed decision-making for an iron ore mine. Rather than setting final policy for the entire life-of-mine, the method enables target grades and tonnage estimates to be revised by re-computation as the mine life proceeds to recognise changes in market conditions and knowledge about the resource.It should be emphasised that this paper is concerned with ore selection rather than ore sequencing. Appropriate ore selection is a necessary but not sufficient condition for maximising value. Having identified the set of blocks that potentially maximise value, the sequence in which they are mined will present a trade-off between producing at constant grade and extracting high value ore early. The sequencing issue is not considered here. It is shown that optimum ore selection for an open pit mine is independent of any consideration of discount rates, although ore sequencing will depend upon the time value of money if the product grade is to vary across time.CITATION:Everett, J E, 2015. Ore selection to maximise value, in Proceedings Iron Ore 2015, pp 443–448 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs.A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanized mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximized, cost if reduced and all profit opportunities are optimized. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

By Bicer N

Current problems in predicting sub-surface strata movement and fracture development due to longwall mining have highlighted the need for more accurate, dependable methods of physical modelling of rock mechanics problems which are beyond the capabilities of current mathematical techniques. Physical model studies of the caved zone above the working faces up to the base of a water source are of importance in attempting to understand changes in mass permeability due to induced fracture zones and the resulting ground water conditions. Turkey's most important supplies of coking coals are to be found within the hard coal resources of the Black Sea coast. Coal seams up to 9 metres thick, dipping at angles as steep as 90 degrees are being successfully mined at the Kozlu Mine. Since 1956, mining operations have been carried out under the sea in dry conditions. The undersea mining conditions of the Kozlu Mine have been investigated using scaled physical models constructed from artificial materials which satisfied necessary scaling requirements. Models representing the in-situ conditions were tested and the following extraction sequence was employed: 1. The Sulu Seam extraction 2. The Acilik Seam extraction (as two slices) 3. The Piric Seam extraction. The displacement of the fixed reference points were subsequently measured using a high precision photogrammetric technique and induced horizontal and vertical strains were calculated.

Jan 1, 1988

By D W. Airey

Frictional rock bolts are widely used because of their low cost. However, they have a thin wall section that makes them prone to corrosion, and they cannot be relied on to provide long-term ground support. It is difficult to assess the capacity after the bolts have been installed as they can only be pulled out if this has been allowed for during insertion. The questions of how long can the rock bolts function effectively and the effectiveness of various surface coatings, which can have significant cost implications are, investigated in this study.A series of accelerated corrosion tests have been performed on frictional rock bolts. The rock bolts, typically 900 mm long, have been inserted into concrete cylinders produced using a styrofoam insert to create the hole for the bolt insertion. Strata rock bolts with four surface coatings have been tested: uncoated black steel, galvanised, enduro (plastic coated) and coated with a proprietary aluminium/zinc alloy. Tests have been performed on two diameters of bolts. Following insertion of the bolts, the concrete cylinders were placed in a large drum filled with saltwater and current was applied to accelerate the corrosion process. The rock bolts were then extracted at various times after the commencement of corrosion. Comparison of the insertion and extraction resistances shows that corrosion initially increases the bolt resistance and that substantial section loss is required for the bolt resistance to drop significantly.CITATION:Airey, D W, 2014. Laboratory corrosion tests of frictional rock bolts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

A series of physical tests have been conducted to determine the actual performance of bunton to shaft side wall connections typically used in new shaft construction in South Africa. The test set-up is described, together with the applied loading, which incorporates a cyclical load component and a quasi-static load component, in an attempt to simulate actual conditions in the shaft. The test results are given and it is shown that generally the performance is adequate, provided double-slotted holes are not used. Generally the fatigue performance is found to be good, with the only exception being cases where the bottom of the bunton is lower than the seating level for the bunton to side wall connection. Arising from the tests, typical design values of connection stiffness, strength and fatigue life are proposed and a design procedure including these three key aspects of connections is described.

Jan 1, 2005

By Smallnone P, Walker B

Mining of the AKI lamproite pipe at the Argyle Diamond Mine (ADM) commenced in 1985. Originally designed to mine ore at a rate of 3.6 Mt per annum, the project has gone through two major plant expansions to a designed production rate of 8.7 Mt

Jan 1, 1998

By Postupack C

A major problem that has continued to plague the surface and underground coal industries is blast induced damage to the coal seam. Blasting Analysis International, in conjunction with a number of other organizations, has continued to address this concern through 14 years of field research in 68 full-scale production environments worldwide. Compiled results were obtained from varying field conditions. These included single and multiple seam coal mines, horizontal, rolling and steeply dipping coal seams and varied borehole diameters (ranging from 102 to 381 mm) and when using various explosive formulations. Results are discussed in detail along with the tools, test methods and analysis techniques to identify and quantify the problems. Over ten major causes of coal damage were identified. A number of practical and economic recommendations are presented that can benefit the entire coal and blasting industry especially in commercial operations whose economic growth relies heavily upon recovering an undamaged coal seam.

Jan 1, 1995

TUNGSTEN occupies an outstanding position amongst metals to-day, for by its use modern manufacturing methods have received a wonderful impetus. The important part played by tungsten in the recent war is not generally recognized. It was tungsten steel, in the shape of highspeed tools, that kept our soldiers supplied with munitions of war at more than one critical period. Tungsten added the necessary hardness and durability to various metals which were indispensable for carrying the war to a successful conclusion. In the words of...

Jan 1, 1921

By S Pontual

Compact and field portable infrared spectrometers have been increasingly used over the past few years by an exploration industry constantly searching for a technological edge and the ability to more accurately and rapidly assess project areas. In particular, this technology allows large amounts of data to be rapidly collected on-site and sample mineralogy, mineral crystallinity and mineral composition to be quickly assessed. In recent years, short wave infrared (SWIR) reflectance spectroscopy has proved useful in a wide range of geological environments and at various stages of exploration programs, from grass roots reconnaissance through drilling programs and resource evaluation. Unfortunately these data have frequently been analysed and interpreted in isolation using time consuming data analysis techniques removed from the realities of a fast moving exploration industry. This paper presents new analysis techniques which allow these data to be efficiently integrated in the exploration program. Although SWIR data contain a wealth of mineral information it is impractical to use this information in its raw form. A more effective approach involves the extraction of key characteristics of these data (ie mineralogy, mineral composition and crystallinity) as numerical values, and the integration of this ædigital mineralogyÆ with more conventional exploration datasets (eg geochemistry, coordinate data, etc). This paper demonstrates that the integrated analysis of sound geological observations, geochemical, spatial and spectral data can quickly lead to a greater understanding of the nature and distribution of target mineralisation. As a first step, software driven pattern matching routines enable the identification of the major clay mineral species in a series of samples (eg kaolinite, montmorillonite and sericite). This allows the major alteration facies and their spatial distribution to be identified. Quantification of diagnostic absorption feature characteristics then allows more accurate determinations of mineralogy to be made (eg mineral composition and crystallinity). Examples of the application of SWIR analysis for alteration mapping from selected porphyry and epithermal systems from around the Pacific Rim are discussed. The data presented are derived from a variety of locations and sample types including drill core, ridge and spur rock chip samples, soil samples and geochemical pulps. In these large alteration systems, the spectral data can be used to describe and map the distribution of various alteration facies as many of these are characterised by clay and phyllosilicate mineral assemblages and are detected by SWIR analysis (eg smectite, chlorite, biotite, illite, muscovite, kaolinite, dickite, pyrophyllite, alunite, etc). In addition, the ability to evaluate even subtle trends in mineral crystallinity and composition is often vital in these systems when looking for vectors towards higher temperature parts of the system. In addition to detailed evaluation of mineralogy, the integration of digital mineralogy data with geochemical data leads to the ability to describe not only geochemically anomalous intersections or regions but also to recognise associations between subtle changes in mineralogy and target mineralisation. This is often important because understanding these mineralogical associations can lead to more accurate targeting and rapid assessment of the project.

Jan 1, 1999

By G K. N Subasinghe

"In the design and operation of mineral processing plants, knowledge of the variability of ore properties and that of the expected metallurgical performance within the orebody is of great importance in order to avoid both production constraints due to inadequate design and less than expected metallurgical performance during operation. Of the many properties that determine the performance of downstream separation processes, such as flotation, gravity separation and leaching etc the liberation characteristics are of primary importance.Current methods of evaluating liberation characteristics of ores such as the use of Mineral Liberation Analyzer (MLA) and QEMSCAN techniques are expensive and suffer from the drawback that these tests are performed on comminuted particles at a given grind size and/or samples of product streams. This problem could be overcome by developing predictive models of liberation that can predict the grade distribution of comminuted products at any grind size based on texture of the parent rock. This paper discusses a procedure that has been developed to predict liberation using information obtained from a sample of the parent rock such as drill core, based on Barbery’s liberation models. The required characteristic statistical functions have been evaluated from image analysis techniques using scanning electron microscope (SEM) images of the parent rock and narrowly sized comminuted particles. Such information can then be used in a predictive model to predict or explain the variability of metallurgical performance at various grind sizes used in future operating plants. The model will predict not only the valuable mineral liberation but also gangue liberation, which will be useful to those who are looking to remove liberated gangue from comminution circuits.CITATION:Subasinghe, G K N, and Dunne, R, 2016. Predictive Model of Mineral Liberation for Geometallurgical Applications, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 347–350 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J Wu

Swirl Flow Technology (SFT), a novel approach for agitation in large industrial slurry tanks, was jointly developed and patented by CSIRO and Queensland Alumina Ltd (QAL). Currently, SFT is used in 16 alumina precipitation tanks at QAL, with the first installation in January 1997. This paper provides insight to the underlying fluid dynamics, which were investigated through pilot-scale experiments. A key finding was that SFT produces tank wall velocities approximately four times that of conventional draft tube agitator systems for the same power input, whilst for solids suspension, much less power is needed. SFT is energy efficient and practical in scaling suppression as demonstrated by the full-scale experience at QAL.

Aug 8, 2011

The characteristics and causes of the spoil pile failures at the Goonyella Mine are described, and research results from investigations of spoil pile instability are discussed. Some effects on spoil stability of the development of deep strip mining projects are considered and recommendations are made for relevant research.

Jan 1, 1981

The history of potential large scale development at Stawell in northwestern Victoria dates back to 1914, when Great Boulder Mines Limited, of Kalgoorlie, Western Australia, took up options on some of the major mines in the Stawell Goldfield. Despite this and other attempts by various groups over the next thirty years, mining activity on the field gradually dwindled to the retreatment of old mill tailings.A static price for gold and indifferent drilling results prevented a major effort towards reopening the field until the late 1970's. A renewed exploration effort led to the discovery of sufficient reserves to justify installation of a carbon-in-leach gold treatment plant.

Jan 1, 1984

By M Dunglison, P M. Cameron

Simultaneous mass-balancing of a mineral processing flow sheet results in adjustments to each data point that reflects the accuracy and precision across the full set of data. In this way, all the good work that goes into designing the sampling and analysis protocol for each sample point is leveraged in order to produce a æbetterÆ set of balanced numbers for every sample point in the circuit. Few operating plants employ whole of circuit balancing techniques to produce reported operating results. This situation is changing with the application of mass balancing technology which utilises redundant data for production accounting and metal reconciliation from product to ore source across multiple phases and multiple time periods. Mine and plant data can now generate credible information to improve productivity. Mine and plant personnel can now use consistent data sets for review and planning. Decisions based on balanced data can be made quicker and with increased confidence.

Jan 1, 2005

By E E. Hall, S, E D. Thimons, R J. Timko

The heart of mine ventilation science and technology is the protection of the life and health of the miner. Lung diseases that result from overexposure to various mine aerosols can largely be prevented by maintaining concentrations below prescribed limits. Maintaining safe aerosol concentrations depends, in part, on our ability to know what mine aerosol concentrations are in a timely and accurate way. The Centers for Disease Control and Prevention (CDC), National Institute for Occupational Safety and Health (NIOSH) has been developing several new tools to help miners monitor respirable coal dust, silica and diesel particulate matter. This paper will discuss three main topics. First, the latest results of the person wearable dust monitor (PDM), developed by Rupprecht and Patashnick under CDC contract. The PDM was tested side-by-side with conventional samplers at a number of US coal mines and results indicated that the PDM was comparable to conventional samplers. Second, improvements to the dust dosimeter monitoring technique that includes a new pump with built-in pressure transducer and algorithm to convert differential pressure to dust concentration have shown good precision. Third, advances in the use of the detector tube technique to monitor tailpipe diesel emissions and ambient diesel particulate matter show that strong correlations exist between differential pressure measurement and elemental carbon in the samples.

Jan 1, 2005

By Ennis P. C

The Mt Keith ultramafic intrusive extends for about 200 kilometres from Agnew in the south to Wiluna in the north. It forms the host for a number of nickel sulphide orebodies including Mt Keith and Honeymoon Well. Long fibre minerals are associated with the orebodies. The presence of these minerals impacts on the issue of tailings disposal from several standpoints, particularly the slurry beaching properties and dust generation from dry beaches. Central thickened discharge (CTD) is an innovative method of tailings disposal that involves stacking tailings in a low conical hill instead of storing them in cells. In appropriate circumstances this leads to savings in capital costs and operating expenditure. The method was introduced to Australia in 1981, and is currently employed at four operating mines, Elura and Peak Gold, both at Cobar in NSW, McArthur River in the Northern Territory, and Union Reefs near Pine Creek, also in the Northern Territory. It is the proposed method for Century Zinc and Ernest Henry, both in Queensland. The paper describes laboratory test work and design parameters for the application of the method to tailings disposal at Honeymoon Well and compares them with comparable data for other CTD systems. Of particular relevance for design purposes are beach slope, density, and water recovery. Wind tunnel tests were conducted on the Honeymoon Well tailings samples to investigate dust generation from the dry beach surface and it was concluded that dust generation from an undisturbed beach would not occur because of crusting.

Jan 1, 1996