Search Documents

By R Jones

OneSteel Whyalla’s grate-kiln-cooler pelletising plant was commissioned in 1968 processing haematite feed from the local South Middleback Ranges mining area. The existence of a magnetite resource beneath the haematite ore at Iron Duke had been known for some time. In 2004, a decision was made to covert the primary iron source for the Whyalla steelworks from haematite to magnetite – known as project magnet. The intent of the project was to convert the feed to the steelworks from haematite to magnetite and to free up the remaining haematite resource for export. The pelletising plant was cut over to a magnetite feed in 2007.The thermochemical differences of magnetite compared to haematite are threefold:1. the introduction of an exothermic reaction during conversion of magnetite to haematite,2. the absence of bound water which existed within the haematite, and3. lower gangue content requiring lower fluxing levels and therefore lower calcination energy demand.The combination of these differences results in a significantly different induration requirement for magnetite as compared to haematite. The change therefore required extensive research and test work to design modifications to the furnace and to ensure appropriate risk mitigation for the Whyalla steelworks.Preliminary pot-grate test work was performed to define the pellet chemistry and confirm the suitability of the magnetite to produce pellets suitable for the OneSteel blast furnace. A heating curve was developed by use of computer-based heat and mass balance modelling. Extensive pilot scale grate-kiln-cooler test work was then performed to confirm the heating curve and to verify and fine-tune the pellet properties. Computation fluid dynamics was used to design the physical changes to the furnace required to achieve the proposed heating curve.Following installation of an additional preheat zone, including a wall and dilution air fans, into the preheating furnace, and installation of an additional wall into the cooler, the modified furnace was commissioning in December 2007. The plant performed as expected during commissioning with the actual heating curve matching the proposed curve and the produced pellets within blast furnace specifications.

Jul 11, 2011

By C Pope, M Tannock

Mining exploration and development projects in Australia are being negatively affected by the highly complex regulatory and bureaucratic processes at all levels of government. These processes affect mining companies operating in Australia by impacting on timelines and the cost of developing a mining project. It is not uncommon for the granting of project approvals to take in excess of five years, meaning that mining companies struggle with productivity, efficiency, time frame and cost issues in respect to their projects in Australia. As the mining boom in Australia is moving from the investment to the production phase, it is now more important than ever to maintain a regulatory landscape that facilitates rather than discourages new investment.While one of our key arguments is that there is too much burdensome regulation and red tape in Australia, we are also strongly believe that regulatory intervention is necessary to ensure that appropriate checks and balances are in place to serve the public interest and manage environmental, health and safety, social and other development-related impacts that may arise from a mining project. However, the regulatory intervention in Australia has come to a point where it is excessive and starting to discourage valuable investment in mining projects for nominal return to the public. Excessive regulation or ‘red tape’ impedes productivity and competitiveness, deters investment and innovation and costs jobs, all of which ultimately impact on the growth of Australia and the standard of living of all Australians.This paper aims to examine and compare the federal, state and local regulations that govern mining projects in Australia. It will highlight how these regulations are unnecessarily complex, lengthy and duplicated and how they can be streamlined to reduce red tape. In doing so, the paper will evaluate the recommendations proposed by the Productivity Commission Report on Major Project Assessments released in 2013, which include the recommendation to move to a ‘one project, one assessment, one decision’ regulatory model.CITATION:Pope, C and Tannock, M, 2015. Project development and regulation red tape – a comparative analysis: does it need to be so complex?, in Proceedings Iron Ore 2015, pp 621–630 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S F. Rogers, K Doumis, J H. Graaf, B J. Barsanti

Advances in technology now allow geotechnical practitioners to better describe the properties and variability of a rock mass through advances in surface and underground mapping, borehole technology and geophysical imaging. Yet the way in which practitioners use this data is not being realised to its full potential and the quality and quantity of data that is collected is often superior to the conventional design approaches that are typically adopted. A discrete fracture network (DFN) approach provides the ideal basis for using this data to generate geologically-realistic rock mass models based on parameters derived from field data, which more effectively capture the variability and rock mass behaviour. However, until recently, the DFN approach has mainly been applied to cave mining and small-scale models associated with synthetic rock mass modelling or groundwater flow modelling for the nuclear waste and oil and gas industries.Ground support design for blocky rock masses in Australia is often dealt with in a rather traditional manner, adopting either an observational empirical approach through rock mass classification systems or conventional wedge stability analysis techniques. Using these methods requires several generalised assumptions about the rock mass fabric and excavation geometry. As such, the support system is often designed for a worst-case scenario based on a predetermined risk tolerance that the mine is willing to accept and a design block size that is generally determined by the proposed excavation dimension.A study by Doumis (2014) used conventional wedge stability analysis and the probabilistic key block analysis software JBlock (Esterhuizen, 1996) to estimate potential block sizes and support requirements. A DFN approach has also been adopted at Callie underground mine using FracMan™ software (Golder Associates, 2014). The methodology of the DFN wedge analysis will be compared with the key block analysis work undertaken by Doumis.CITATION:Graaf, J H, Barsanti, B J, Doumis, K and Rogers, S F, 2014. Towards the implementation of discrete fracture network modelling as a geotechnical design tool – case study of callie underground mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D L. Reid, G Nwaila, J Petersen, J-P Franzidis, Y Ghorbani, M Becker, F C. de Beer, L C. Bam

Traditional methods of gold extraction have involved comminution and processing via cyanide leaching, all of which are associated with energy, cost and environmental implications. Subsequently, numerous opportunities for improvement and optimisation strategies in gold mining and processing have been explored, including heap leaching, which has significantly lowered comminution costs. This paper explores the effect of the more energy efficient high-pressure grinding rolls (HPGR) on the comminution behaviour (especially on the crack density) and cyanide leaching performance of laboratory reactors study on run-of-mine gold ore comprising the Ventersdorp Contact Reef (VCR) and the Elsburg Reefs (ER), sourced from Carletonville in the Witwatersrand Basin in South Africa. The ore was comminuted using HPGR at three different pressure settings (120, 90 and 60 bar). Large (-16/+11.2 mm) and small (-5.6/+4 mm) particles of the HPGR product where then mineralogically characterised using optical microscopy, quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) and X-ray computer tomography (CT) before cyanidation. The results of the leach experiments indicated a correlation between gold extraction, particle size and crack density. Mineralogical characterisation of the ore indicates that the Fe-sulfides present in the VCR are likely to be more reactive than those in the ER, thus having a more favourable influence on gold cyanidation. Overall, the results show promise for the heap leaching of Witwatersrand gold ores prepared using HPGR and demonstrate the value of a multi-disciplinary geometallurgical approach.CITATION:Nwaila, G, Becker, M, Ghorbani, Y, Petersen, J, Reid, D L, Bam, L C, de Beer, F C and Franzidis, J-P, 2013. Morro do Ouro geological model with a metallurgical view, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 75-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By D Ford

BHP BillitonÆs new rotary iron ore car dumper installation at Finucane Island (Port Hedland) was constructed to increase the total capacity of the port facility from 110 Mtpa to 120 Mtpa and to allow for incremental capacity increases in future. The arrangement of the dumper is similar to other car dumper installations existing on site. To construct the facility, approximately 120 000 m3 of material was excavated in six months, to a total depth of 22 m. The saline water table was nominally 6 m below ground level and the materials excavated varied depending on depth, ranging from sand to mangrove muds. There was a need to retain the sides of the excavation and limit the amount of water from entering the excavated area. This was required to allow excavation to progress and had to be maintained during construction of the permanent concrete and steel facility. The excavation was backfilled progressively as construction progressed. Various retaining wall methods were investigated with the preferred option being sheet piles secured by walers and ground anchors. Detailed electronic models were developed and assessed to complete the final design arrangement. Dewatering bores around the perimeter of the excavation removed the groundwater to intercepted sumps within the site. A strict and methodical program was developed to monitor the integrity of the temporary works and the quality of the groundwater. The works were completed on time despite the following challenges being encountered: availability of resources and equipment, movement of mobile plant on æboggyÆ materials, difficulty driving sheet piles into material at depth, drilling of ground anchors to 32 m, grouting of ground anchors, greater than expected groundwater flows, and the risk of hydrocarbons within the groundwater. The lessons learned from the use of the retention system and, in particular, the associated construction challenges overcome, provide a sound basis for similar work in this buoyant resource market. The conference paper describes the temporary works options investigated, design considerations and processes, construction methodology and challenges encountered, and the monitoring systems developed. Lessons learned are also discussed.

Jan 1, 2007

By N Schofield

For the sampling of particulate materials in mineral exploration and mining, the fundamental sampling error (FSE) introduced by Gy is a measure of the constitutional heterogeneity of the sample lot and is expressed as the relative standard deviation of subsample grades of a particular mass. The FSE is presently regarded as an important indicator of quality for samples used in resource estimation. Constitutional heterogeneity describes an ideal state of heterogeneity with respect to all constituents of the lot such that the fundamental error among subsamples of a particular mass is minimised.In this paper, the term ‘sampling precision’ used in relation to mineral resource sampling usually refers to a statistic based on the assay results drawn from pairs of separate subsample splits of multiple sample lots. The pairs of splits are extracted after the lots have been prepared by crushing and pulverising to meet specified criteria of grain size and subsample mass. There is presently no generally accepted method of calculating the ‘sampling precision’ from such paired data but some form of the relative standard deviation that is consistent with definition of the FSE is preferred here. The work of Thompson and Howarth in the 1970s on geochemical analytical precision, which has been subjected to extensive examination and criticism by Stanley and Lawie (2007), and that of Francois-Bongarçon since the 1990s forms the background to the discussion in the paper.A significant aspect of the application of Gy’s sampling theory to sampling in gold deposits is the requirement that the fundamental error be maintained at less than ±20 per cent. The most important reason for this is to ensure that the effects of other sampling errors such as the grouping and segregation, and increment delimitation which can cause local and global biases in sampling are kept as small as possible. This paper is focused mainly on the quality of sampling in gold deposits and looks at an alternative to the use of a constant sampling precision applied to a collection of lots with varying average grade. A theoretical model for the FSE based on duplicate sampling is presented and the simulated results of the model are compared to practical outcomes of real duplicate pairs drawn from multiple sample lots. The goal of the work is to present a more informative analysis of duplicate sample data from multiple lots which may allow a more informed view of the potential for bias generating errors during sample preparation and processing.

Aug 22, 2011

By P Clark

This paper discusses the challenges, solutions and lessons learnt as tunnelling work continues on the Melbourne Main Sewer Replacement (MMSR) project.The MMSR project is a $220 million dollar project for the Melbourne Water Corporation. It involves the construction of approximately 4.2 km of new sewer from the southern fringe of the CBD through the inner metropolitan suburbs of Port Melbourne and South Melbourne.Of the 4.2 km of sewer currently in construction approximately 2.2 km will be constructed using a 2.95 m diameter Lovat EPB tunnel boring machine (TBM) with approximately 1.9 km of small diameter (300 to 600 mm) reticulation sewers constructed using trenchless techniques.These sewers are being constructed in a dense urban environment, which means that the tunnels and shafts are often in close proximity to buildings and structures. The underground constructionof the sewer is further complicated by the variable geology of the ancient Yarra River delta which includes weathered basalts, the infamous Coode island silt formation and fine loose sands.Some of the key challenges and lessons learnt so far during construction include:· steering and alignment control of the TBM through very soft silt with little residual strength,· development and refinement of a monitoring and alarm system for leaving the machine dormant on a day works only project,· control and measurement of tunnel lining defl ection during ring build and grouting,· prediction and monitoring of surface settlements during tunnel excavation,· improved understanding of the geology and hydrogeology at this previously unchartered area of Melbourne,· consolidation settlement due to dewatering at shafts required careful construction controls, and· ground support and excavation in close proximity to the existing 110 year old sewer which requiredvery detailed risk control measures.

Mar 8, 2011

By C F. Stokes

The Trident Gold Deposit has been successfully developed by Alacer Gold (formerly Avoca Resources Limited) into a 1.3 Mt/a operation in the space of four years from discovery to first gold pour (2008). The current in situ Resource for Trident is estimated to be 5 900 000 t @ 5.0 g/t for 940 000 ounces at a cut-off of 1 g/t or 2 g/t depending on ore style. Production to date (Alacer and previous owners) is in excess of 500 000 ounces. The deposit lies towards the southern end of the Norseman-Wiluna Greenstone Belt in the Archaean Yilgarn Craton, where it is centred on the historical Higginsville Mining Centre, midway between the world class gold centres of St Ives (+15 Moz) and Norseman (+6.5 Moz). Trident is hosted primarily within a thick, weakly differentiated gabbro with subordinate mafic and ultramafic lithologies and comprises a series of north-northeast trending, shallowly north plunging ore zones. The deposit comprises two main mineralisation styles; large wallrock-hosted ore-zones comprising sigmoidal quartz tensional vein arrays and associated metasomatic wall rock alteration (Eastern Zone, Western Zone and Apollo) hosted exclusively within the gabbro; and thin, lode-style, nuggety laminated quartz veins (Athena and Artemis) that formed primarily at sheared lithological contacts between the various mafic and ultramafic lithologies. The initial interpretation of the Trident Deposit was based on steeply-dipping structures controlling the zones of mineralisation, with much of the targeting and drill-testing aimed at this style of orebody. Subsequent exposure of the orebodies has identified a series of shallow-east dipping mineralised systems (interpreted to be large reverse shears) that at their intersection with the steep-dipping structures cause significant gold enrichment. It is postulated that both orientations are primary fluid pathways with the intersection between the two resulting in zones with significantly high concentrations of gold mineralisation (in excess of 300 000 ounces). This new understanding on ore controls at Trident has identified that the thin lode-style shear-hosted laminated veins are continuous for over 1700 m along strike as they step en echelon down-plunge. In addition, a repetition and periodicity to the intersection between these steep dipping lode-style systems and the shallow-dipping mineralised zones (estimated to be 700 - 900 m down-plunge) has been identified which has considerably increased the down-plunge potential of the Trident Deposit.

Aug 22, 2011

By L Drowley

The Adelaide Desalination Plant (ADP) draws raw sea water into the facility and returns saline concentrate to the Gulf St Vincent via subsea conduits. This paper describes the detailed design and construction methodologies developed for the cross connection tunnel excavation. The paper concentrates on key design elements which include:· lateral breakout support of the segmental tunnel lining,· ground improvement grouting in the zone of the cross connection tunnels due to extremely variable and weak ground conditions, and· excavation methodologies and proposed support types of the riser to tunnel cross connections.The design process consisted of developing concepts, detailed risk assessment, three-dimensional (3D) finite element modelling and structural analysis for temporary support of tunnel lining; functional design of the ground improvement grouting and the temporary support; and permanent lining design of tunnel to ocean riser connections in a mixed soft ground/hard rock environment.The paper also presents conclusions of the design based on construction data available, and highlights the close collaboration between the design team and construction team.

Mar 8, 2011

By A D. Campbell

The Homer Tunnel is located in a remote area of the South Island of New Zealand and carries large numbers of tourists to Milford Sound through an avalanche prone area. The tunnel is 1280 m long with a steep ten per cent unidirectional grade descending to the west. Construction of the tunnel began in the 1930s and was completed to a nominal 6 m width in 1954. In 1996, two passing bays were stripped-out to accommodate bi-directional flow of tourist coaches. During all phases of construction and widening there have been episodes of strain bursting.The condition of the tunnel and standard of internal services is below current international practice, principally in terms of; in-tunnel air quality, fire life safety, ground support, and road safety. A number of near-miss events have occurred involving coach fires on the approaches and inside the tunnel. The national road authority, NZTA, is considering a substantial investment to improve amenity and safety of the tunnel.This paper describes the rationale for the proposed upgrade works and the investigations undertaken to enable that design. A holistic approach to road tunnel safety has been adopted that balances the key interrelated safety drivers, namely; tunnel lining, traffic operations, ventilation, power supply and egress while ensuring continuity of safe access to Milford Sound.

Mar 8, 2011

By D FitzGerald

A critical component of any new tunnel design in a complex geological setting is the development of an integrated three-dimensional (3D) geology model with a full set of geotechnical properties of the rocks present. A novel means of predicting the geology based upon sparse observations of structural geology at the surface and from drill holes has been developed and used in several major tunnel studies in Europe.An example of this is the Lyons-Turin twin rail tunnel which is still in a development phase. This tunnel has been in planning and development for over 15 years already. An important aspect of this work is to characterise geological uncertainty along various possible tunnel paths as an input into early design optimisations for time, cost and risk avoidance strategies. Once the tunnel works commence and more detailed geological data is collected by daily mapping, progressive refi nement of the geological model is desirable; geological conditions still to be encountered can be more accurately predicted. Faults and their offsets, dykes, geological unconformities, folding, as well as standard sedimentary processes are all correctly modelled in the software. It is important to allow for seamless interchange of geological models at various scales with CAD workflows so that sufficient detail can be readily accessed at the required scale. Also, the proposed tunnel in its correct geometry can become a ‘section’ in its own right. Progressive detailed local geology models in the vicinity of the advancing head are created from the regional scale work by cutting and pasting a starting model, then adding all the extra detail for the required engineering geology work.For all rocks, most standard geotechnical quantities such as sonic velocities, Young’s modulus and Poisson’s ratio are handled. These and any other phenomena from borehole observations can have variograms calculated and stratigraphically constrained estimations made in a least biased geostatistical manner, in advance of the tunnel. RQD, or a prediction of rock fractures, is handled by the faulting and folding modelling facilities. This is probably the more interesting issue to pursue, as the fractal nature from small scale fractures and joints, to large-scale faults, can now be characterised more convincingly.

Mar 8, 2011

By L Scheunis, A Van den Bulck, E Jak, K Verbeken, M Shevchenko, R Starykh, I Bellemans, P-J Boeykens

As a result of the globally increasing consumer use of electronic devices, it is expected that pressure will increase on the supply chain of precious metals. Hence, recycling of these electronics becomes increasingly important, as well as optimising the current processes. One major issue in metallurgical processes is the amount of metal that is lost into the slag. This metal loss is inherent to the production process and therefore, additional processing steps such as slag cleaning may be required. Slag cleaning can be done in electrical resistance furnaces where heat is produced using the Joule effect, making the slag’s electrical conductivity an important operating parameter. Since slags are ionic liquids, the electrical conduction happens via the movement of ions which is called ionic conductivity. However, within the presence of transition metal oxides, a second mechanism of conductivity occurs as electrons are able to hop from one transition state to another, which is known as electronic conductivity. As ‘FeO’ is a common slag component in the non-ferrous pyrometallurgical industry, both mechanisms are present, but their proportions vary with the respective amounts of the two forms of the multi-valent ions and hence, with the oxygen partial pressure. The goal of the present study is to develop an experimental set-up and methodology for measuring the electrical conductivity of synthetic SiO2 – CaO – AlO1.5 – ‘FeO’ slags at various oxygen partial pressures.

Jun 19, 2024

By R Jaine, D Strang, M Fowler

"This paper presents a case study demonstrating active geotechnical pit slope management at the now completed Carina Iron Ore Project operated by Mineral Resources Ltd (MRL). The site is located 105 km north-east of Southern Cross, Western Australia. The paper is primarily focused on the slope stability failure modes and the remedial measures employed to maintain mining.Between a quarter and a third of the excavated slopes were impacted by some form of instability that was beyond expectations of the intended slope design criteria and common practice. Ongoing mining was supported by intensive geotechnical pit slope management including close cooperation between geotechnical, mine planning and operations staff to achieve timely and practical mining solutions.Mining encountered varied slope failure mechanisms which required a combination of remedial solutions comprising: horizontal depressurisation holes, deferral of excavation, unloading, buttressing and catch berms.The root cause of the challenging slope performance was a mismatch between the predicted and encountered geotechnical model, resulting from a failure to recognise the critical mechanisms that control slope stability.Despite the extensive zones of instabilities at completion of mining, full ore recovery was achieved without major delays and in a controlled and safe manner.Citation:Fowler, M, Strang, D and Jaine, R, 2016. Adapting to Geotechnical Change - a Case Study of the Carina Open Pit Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By J Li, J Regan, D Payne

The Caval Ridge Mine is an open cut coalmine and located within the Bowen Basin region in Central Queensland, and commenced mining and processing operations in 2014. A number of geotechnical challenges for managing dragline bench and lowwall stabilities have been encountered in both southern and northern pits over the years. Southern Pits contain steep seam dips of up to 15° (27 per cent) whilst the northern pits also have shears below pit floors. Geotechnical guidelines to manage the risk of dragline bench failure and lowwall instability have been developed and improved since these geotechnical challenges were identified. The dragline guidelines include dragline tub offset distances from the 60° Line (SDL) or buttressing thickness for different seam dips greater than or equal to 8°. The low wall stabilisation guideline established floor disruption widths and depths depending on seam dips and presence of floor shears to known depths of up to 3 m. As mining operations advance, lowwalls have remained stable until floor disruptions were fired, then returned to stable soon after the shot. The maximum distance of lowwall cracking with blasting has been as far back as the second spoil peak (the prestrip truck dumps construction limit). These failures need to be eliminated to allow the operational flexibility and haulage benefit of constructing the prestrip truck dumps behind the first spoil peak, while maintaining no risk to personnel or equipment. The floor shear depth was verified by collaborating with the exploration teams and taking advantage of the already planned 8-inch coal quality core holes, drilling them an extra 5–10 m past the coal seam floor and locating the shear presence. With this continuous improvement effort, no lowwall failures have occurred during floor disruption firing from the second strip after the new floor disruption depth guidance have been applied. This paper documents the processes for developing these geotechnical guidelines, operational implementation, and outcomes. Operational applications over the years confirmed that these guidelines have effectively managed the dragline bench and lowwall failure risks related with the steep seam dips and floor shears in this open cut coalmine.

Nov 29, 2022

By A Maier, M Goldner, C Gimber

Given the ongoing global crises of climate change and nature loss, with the World Economic Forum (WEF) identifying them as the top risks to global economies in terms of both likelihood and impact in the coming ten years (WEF, 2022), there is increasing, pressing demand for companies to demonstrate they understand their climate and nature related risks and look toward contributing genuine beneficial environmental outcomes. Within the mining industry, mine closure is the obvious field in which climate and nature positive strategy can be linked with operations. To do so, there is a need to challenge long-held assumptions around closure in the mining and regulatory context; particularly, to shift the focus from closing individual mines to considering regional opportunity generation and value creation.

Aug 2, 2023

By B D. Saffron

In 1983, open cut coal mining operations were suspended at the Tent Mountain coalmine, located in Alberta, Canada in an area called Crowsnest Pass. Montem Resources (‘Montem’), an Australian mining company, purchased the asset in 2016. They conducted several drilling campaigns and undertook environmental monitoring with the intent to restart operations. In 2020, Montem completed a Definitive Feasibility Study, which indicated a mine life of more than 14 years.

Aug 2, 2023

By D Stepanenko, G Stovpchenko, L Lisova, D Togobitskaya, L Medovar

Classical electroslag remelting of consumable electrodes is a drop-by-drop melt feeding through a slag layer into a renewing molten metal bath, slowly solidifying into a homogeneous, dense, defectfree ingot in a copper water-cooled mould. The new look at the additive nature of the electroslag remelting (ESR) process in a protective atmosphere allowed us to formulate the principles of a comprehensive thermodynamic-based model that can predict dynamic changes in slag and metal composition at certain ingot remelting. The model considers drastically different slag-to-metal mass ratios at the beginning and end of remelting and predicts gas, slag and metal composition in a chain of thermodynamic subsystems. Despite consisting of calcium fluoride and stable oxides, the ESR slag can oxidise main and active elements from steel and alloys (primarily aluminium, titanium and silicon) due to chemical reactions between slag and metal. ESR is not an electrochemical process in its nature. However, slags are ionic melts and deviation in their composition causes a change in their properties, affecting both operation mode and ingot quality. Another important understanding derived from the modern metallurgy technological route is that the ability to refine metal from impurities is not a priority for the ESR because consumable electrode has already passed all stages of refining and deep degassing at ladle treatment that changes ESR slags engineering principles. The critical importance became slag’s ability to generate process heat and keep the melting composition in the metal bath unchanged (except for non-metallic inclusions assimilation). Slag engineering for ESR required a compromise between chemical inertness to a metal composition and desired physical properties deriving from technological reasons. The Directed Chemical Bonds Concept (DCBC) in a multicomponent oxide system was used to build predictive models of electric conductivity and the melting temperature of fluoride-oxide slag based on their chemical composition. Both models help to design a customised composition of effective slags for steel and alloy groups or individual grades, and they are significant steps in the development of a comprehensive model of electroslag remelting.

Aug 21, 2024

By A Bird

Gravity gold circuits have an important part in reducing operating costs and maximising recovery in modern gold plants where coarse gold is present in the ore body. The design and selection of equipment has a vital part in the overall effectiveness of the gravity gold circuit. There are a number of associated factors that need to be taken into consideration when selecting the most suitable equipment for gravity gold circuits including occupational health and safety, security and labour requirements. This paper is a case study that outlines the validation behind the design, selection of equipment and subsequent benefits of the recent upgrade of the gravity circuit at the Marvel Loch gold mine with the main component to the upgrade being the installation of a Consep Acacia Reactor. Since the upgrade there has been a significant increase in gravity recovery, which has reduced the amount of gold reporting to the leaching circuit therefore reducing reagent consumption and overall operating costs. There has been an increase in overall gold recovery and therefore increased gold production. The benefits to occupational health and safety include the removal of toxic gases being released in the gold room during the previous practice of gold concentrate calcination and the removal of the arsenic and nickel from the gold doré, which poses a risk during refining. Manual handling and security has improved as there is no physical contact with gold concentrates during the automated process using the Acacia reactor. The total time for gold room personnel working in the gold room has also reduced from around six hours per day to less than one hour per day.With the continuing development of low grade gold deposits, there will be an increase in demand for low capital, high recovery gravity gold circuits that can significantly increase overall production while reducing operating costs.

Aug 8, 2011

A novel approach to validate size distributions obtained from bubble sizing techniques is introduced. The experimental rationale consists in verifying whether the output features the anticipated bi-modality when two uni-modal populations (ca. 0.5 and 5 mm) are mixed in a bubble column. The degree of deviation is quantified by comparing the calculated and real proportions on a volumetric basis. A sampling-followed-by-imaging technique was used to proof the concept. The results showed the anticipated bi-modality in which the real and calculated proportions corresponded with a deviation of less than 15 per cent, considered good given the severity of the test. However, the deviation was correlated to the superficial gas velocity (Jg) in the column and was consistently against smaller bubbles. Possible sources of bias are suggested.

Jan 1, 2005

By J P. Sykes, C Gemell, A Trench

The perceived and actual impact of government mineral policy upon the government share from gold mining revenues is assessed for ten key countries in which the gold sector is of relevance in advancing economic growth. Five African and five South American jurisdictions are considered, namely Burkina Faso, Ghana, Mali, South Africa and Tanzania from Africa; and Brazil, Chile, Colombia, Guyana and Peru in South America.Both the headline corporate income tax rate and royalty level are identified as poor indicators for the total government share. In addition, significant differences between industry perception and actual government tax levels are identified by this study. The quantitative financial analysis shows that there is no clear relationship between individual taxation rates, taken in isolation, and the overall average effective tax rate (AETR) paid by the project over its life. Neither companies nor governments should use individual taxation rates, or industry perceptions, in isolation to assess the overall competitiveness or equity of a country’s minerals taxation regime – such analysis can be very misleading.In this study, the perceived impact is determined from the well-established Fraser Institute survey published each year, and in 2014 compared 122 minerals jurisdictions globally. The actual impact is determined from quantitative modelling of the financial performance of a hypothetical gold mining project in each country. The technical parameters of the project are held constant; instead the differing mineral policies in each jurisdiction are applied to determine the resultant impact upon the relative share of the economic rents delivered to both private and public sectors. In the quantitative analysis, the total government share varies from 36.3 per cent in South Africa to 66.5 per cent in Ghana.CITATION:Gemell, C, Sykes, J P and Trench, A, 2016. Is perception reality? Evaluating the fiscal attractiveness of international jurisdictions for gold mining investment, in Proceedings International Mine Management Conference, pp 227-238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016