Search Documents

Current models for the origin of banded iron-formation (BIF) derived in situ iron ore deposits assume that the typical chert and iron oxide banded BIF is the primary rock from which enriched iron ore deposits arise by the selective leaching of quartz and the residual accumulation of the iron oxides. Weathering extends to the base of all the hematite deposits of the Hamersley Province, which lie within the saprolitic weathering zone, as shown by the preservation of the primary textures, and are overlain by a hydrated goethite zone representing the solum. Since groundwater typically contains dissolved silica, derived from the hydrolysis of silicate minerals, greatly in excess of the saturation solubility of quartz, it is incapable of removing quartz from below the watertable, and quartz is preserved in all saprolites derived from quartz bearing rocks. Quartz may be dissolved in the solum due to the influx of meteoric water having little or no dissolved silica, but soil-forming processes that dissolve quartz likewise alter the oxides by hydration and transposition with consequent destruction of primary textures, and there is no suggestion of soil-forming processes having produced the deposits, which typically extend to considerable depths below the water-table. A characteristic feature of the typical hematite orebodies is the unaltered nature of the iron oxides in the ore compared to those in the adjacent cherty BIF. Although the solubility of ferric iron at >10 ppb is much less than quartz, any process capable of dissolving the huge volume of quartz must also affect the iron oxides, but evidence of this is completely lacking in most ore deposits. Hydrothermal alteration at Koolyanobbing in the Southern Cross Province affects both cherty BIF and ore, and clearly shows equal mobilisation and recrystallisation of hematite within quartz/hematite veins and in the surrounding cherty BIF, which shows no evidence for the selective leaching of quartz. Similarly, any metamorphic process capable of removing all quartz from BIF would leave characteristic evidence in the remaining oxides. However, a hydrothermal process may account for at least portions of certain ore deposits, in which the chert bands have been replaced by carbonates at comparatively low temperatures, to produce a quartz-free magnetite/ carbonate rock that is readily upgraded to high-grade ore by supergene dissolution of the carbonates. This process is interpreted to have formed high grade ore at Mt Gibson, Koolyanobbing æAÆ Deposit and Mt Tom Price North Deposit. In addition to carbonate replaced cherty BIF at Mt Gibson in the Murchison Province, there are extensive sequences of magnetite BIF without chert bands, and this chert-free facies of BIF is interpreted as the precursor to the majority of in situ hematite ore deposits, through oxidation and weathering of magnetite and iron silicate and carbonate minerals. The world-class martite/microplaty-hematite deposits of the Hamersley Province are a special case of BIF-derived iron ore deposits that were initiated during the Proterozoic era. Evidence from overlying Wyloo Group conglomeratic horizons containing clasts of Hamersley Group BIF indicates that microplaty-hematite formed within the clasts before deposition, and that Proterozoic subaerial oxidation and weathering of uplifted Hamersley Group formations produced the microplaty-hematite in both chert-free and cherty BIF.

Jan 1, 2002

By R LEATHAM

Long hole drilling underground has come a long way since 'down the hole' surface drills were first taken underground. The underground miners have progressively developed the use of long hole stope drilling from the 'quarry blast' to a precise and selective removal of ore while leaving the remaining structure as undamaged as possible. To reach this position has involved the development of equipment and explosives to give the desired results. This paper reviews some aspects of long hole stope production drilling.

Jan 1, 1992

By T G. Neville, G Terrey, J Burns

This paper explores recent industry training programs and lessons for supervisors. The Belbin Team Role model was used to increase participants’ awareness of behaviour and its application. The application of the Belbin model to underground, open cut mine and quarry supervisors is discussed.The key to team success may rest with the expertise and experience of its members, but increasingly effectiveness depends on how team members understand, acknowledge and support each other’s behavioural strengths. Discovering strengths is a challenge, both for their measurement and for the encouragement of team members to use the knowledge of themselves and others in the team. Using behavioural models provides a constructive approach and a language for supervisors as they build personal motivation and engagement.Prima facie, the mineral industry’s work may be too vigorous for teams and their managers could be more prone to use ‘solo’ or traditional management styles. Managers and supervisors must know when work allocated to a team is appropriate or where individual effort should be applauded and rewarded. For practical people with well-developed technical skills, improving the soft skills necessary for a supervisor requires some reflection and effort. The Belbin behavioural model can be an effective tool for recognising characteristics that can assist teams to be more productive.Experiencing the Belbin Team Role model as part of an industry qualification is important for supervisors studying to refine their team leadership skills. Data are available for participants to assess the nature of their teams and to confront the appropriateness of the behavioural mix for the work of the team and its individual members.So what are the next steps? All team development must have a place in the strategic thinking and plans of the enterprise. This needs a visible presence of senior managers and supervisors in managing a team culture with practical links to workplace priorities and professional development with continuous improvement.CITATION:Burns, J, Terrey, G and Neville, T G, 2016. Supervisors and teams at work, in Proceedings International Mine Management Conference, pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By A Nixon

The Australian mining industry has changed dramatically over the past 20 years in terms of mining methods, mining equipment and human resource policies. The industryÆs approach to safety and health in terms of attitudes, style of legislation, and risk management techniques has also changed significantly. These changes have had and continue to have major impacts on the design of underground mine ventilation systems. In some areas, trends are clearly emerging. In other areas, mine ventilation planning remains very æreactiveÆ and is performing poorly in terms of providing a safe and healthy work environment at a reasonable cost. New concepts involving the role of ramps and shafts, the provision of refrigerated air, æventilation on demandÆ and newe gress and entrapment approaches are likely to be incorporated into mine planning and operating practices over the next ten years. This paper discusses these and other trends and identifies some likely future developments in the area of hardrock mine ventilation.

Jan 1, 2005

By J Naser, M Tuck

This paper reports a computational study using computational fluid dynamics (CFD) in a mine ventilation system. Ambient air is injected to a rectangular mine drive through a circular duct. Moisture evaporates from shaft wall depending on flow properties of air in the drive-duct system. The physical process involves simultaneous momentum, heat and mass transfer. A species transport equation is employed to account for the moisture concentration in air. The momentum equation is solved using standard k- model, while energy and species transport equations are solved using standard expressions for moisture evaporation rate and heat flux from the drive wall. The aim of this paper is to investigate effectiveness of CFD simulation in relation to mine ventilation in a drive where a significant mass transfer phenomenon occurs. Results from simulation are compared with existing data from a site in Victoria.

Jan 1, 2005

By D Xiong, G Xu, L Yao, F Wang, Y Duan

The goal of this project has been to digitise and use drill parameter data from rotary drilling (measurement while drilling; MWD) for a more effective planning of the blasting process in surface mines. A more accurate and reliable digital drilling and automatic hardness identification technology was developed, which includes both a hardware and software system. In the aspect of hardware, we designed a positioning, navigation and hardness perception terminal system which consists of a global positioning system original equipment manufacturer board, programmable logic controller and sensors of measuring major parameters, and a wireless data transmission system which combines digital blasting platform and wireless transmission facilities. In the aspect of software, we developed the navigation software of locating blastholes using LabVIEW and C++, and the blasthole design software using AutoCAD ActiveX (C#) technologies. This new technology is applied at Jiangxi Dexing Copper Mine, and initially realising the digitisation of drilling and hardness identification in blasting zone.CITATION:Duan, Y, Xiong, D, Yao, L, Wang, F and Xu, G, 2015. Advanced technology for setting out of blastholes and measurement while drilling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The Kelian gold mine which was developed in East Kalimantan Indonesia in 1990 - 1992 is scheduled to complete mining and processing operations in 2004. This will have a major impact on the neighbouring communities who have benefited from the jobs, economic activity and infrastructure development which has been generated by the mine. Currently, there are no formal regulations or standards specifying the procedures for relinquishment of mining leases in Indonesia. Furthermore, a move towards regional autonomy, providing greater authority and responsibility to local (regional) areas, has recently been implemented in Indonesia and limited capacity exists in the new regional governments. Consequently, in October 2000, Kelian Equatorial Mining (KEM) initiated a partnership with the local community and government to explore sustainable post-closure options for the mine site and community development programs. The Kelian mine closure strategy seeks full involvement of all stakeholders through the Kelian Mine Closure Steering Committee (MCSC) in the development of sustainable solutions which will enable communities to secure long-term benefits and minimise post-closure risks from the KEM operations. This organisation, jointly chaired by the Head (Bupati) of the regional West Kutai government and the KEM President Director, with representatives from the local communities, governments and NGOs, has developed a Charter, a website and evaluation criteria to ensure accountability and transparency. There are four technical working groups, consisting of representatives from the mine, local community leaders, NGOs, Universities, Local, Provincial and Central Government Departments, which report to the Steering Committee. These working groups have researched, developed and recommended sustainable options to the Steering Committee. The MCSC has met quarterly to examine options in accordance with the criteria set out in the Charter and has endorsed sustainable solutions which have support from Government, Community and the mine. This paper describes the closure risks, sustainable outcomes derived through the Kelian mine closure steering committee process and outlines the methodologies used to develop and endorse sustainable solutions in a society with limited capacity undergoing enormous change and uncertainty.

Jan 1, 2003

By J Player, G Sweby, S Webber, E Jones

Seismic systems are a tool for the monitoring and forecasting the rock mass response to excavation. Common issues encountered at mine site audits and reviews are: how to design an effective seismic system, implementation of the design, interpretation of seismic source results and understanding the reliability of the seismic source. These issues are often a function of several items including: • Experience of site personnel in undertaking seismic system design. • Personnel not envisioning multiple phases of system expansion to understand system robustness issues. • System design/expansion occurring in response to damaging seismic activity rather than planned expansion of a system • The mine access development is often localised in comparison to the total orebody being mined hence, planning sensors in longholes in advance of development rather than in short holes close to development will improve the three-dimensional aspect of the network. • Limited site processing of the seismic event data, hence engineers do not see the uncertainty associated with event location, size, source and system layout. Mine site users require a framework to appreciate the challenges and limitations in locating large events. For example, event locations are given as precise measurements (to the nearest centimetre) whereas the volume of deformation resulting in the event often has dimensions of tens of metres or more (as defined by the source radius). A stronger awareness of the uncertainty of rock mass yield within large seismic sources will assist site users in the interpretation of rock mass damage. The encountered design and implementation errors are reviewed and discussed with a practical set of rules presented to provide a robust seismic system that provides consistent results and increases the user’s understanding of uncertainty in source location and size. The authors’ experience across multiple mine sites, seismic systems and damaging seismic events over a 30 year period has been summarised into practical rules for site personnel of all experience levels.

Nov 29, 2022

Ordovician metasedimenIs near the Karamea Bend and east of Ihe upper Carboniferous Karamea batholith were intruded by acidic stocks during the Cretaeeous. K/ Ar dating of two of the stocks gave 110 ± 3 millionyears whereas the batholith granite gave 290 8 ± million years. All but one of the stocks mapped lie on an approximately ENE line along which they show gradation in composition, texture, and alteration.Most of the intrusions have produced homfelsic haloes in the surrounding rocks but the hydrothermal alteration centred near the head of Questa Creek is quite distinct. Here much wider zones of alteration are characterised by chlorite, green biotite, sericite, and quartz-orthoclase in order towards the centre, though no stock crops out. Each zone of stronger alteration is heralded by "spots" containing the next characteristic mineral.It is suggested that a late phase of the intrusive period that gave rise to the outcropping stocks also gave rise to a volatile-rich intrusion still hidden beneath the head of Questa Creek.

Jan 1, 1976

By M Akop, G Phillips, L Elliott

An estimation geologist has many tools in their kit and using the correct one for the job is vital for creating a useful model. Reconciliation is a key step to monitor the performance of a resource model and to ensure the correct tools have been selected and appropriate parameters are set. This paper presents an example of refining the estimation methodology for a Channel Iron Deposit (CID), resulting in an improved model. Rio Tinto Iron Ore (RTIO) CIDs are unique iron ore deposits located in the Pilbara region of Western Australia and contribute a significant volume to the world’s seaborne iron ore market. A problematic feature of these deposits is the irregular dispersion of clay pods that cannot be delineated with confidence within the resolution of the exploration drilling. Resource to grade control reconciliation showed an over-prediction of high-grade material in the resource model. A fresh approach was required to improve grade and tonnage predictions. Historically, clay pods were delineated using traditional wireframing techniques and estimated using ordinary kriging with hard boundaries. The new method utilised indicator kriging to estimate the probability of clay. Probabilities generated from the indicator kriging estimate were used as an additional weighting following the ordinary kriging of grades. Results showed indicator kriging improved global high-grade tonnes reconciliation, however, as expected, it did not improve the spatial prediction of clay. Based on improved reconciliation results indicator kriging has now been adopted as a suitable alternative for analogous CIDs at RTIO. These improvements benefit the mine planning process, but do not replace grade control models.

Mar 22, 2022

By P Holtham, W Valery, P Baguley, A Jankovic

There is a growing interest in magnetite ores because of the increasing demand for this commodity. With these ores, there is significant cost associated with milling the ore to fine sizes using ball mills in closed circuit with hydrocyclones. Cyclone classification efficiency tends to be poor due to the large difference in density between magnetite and gangue. This decreases the grinding circuit efficiency and results in over-grinding of magnetite. The objective of the work described in this paper was to modify the Bond locked cycle milling test procedure to quantify the loss of grinding circuit efficiency due to the mineral density effect. The locked cycle test procedure described here includes a stage of magnetic separation treating the closing screen undersize, which allows simulation of magnetite classification. The effect of classifier efficiency on low-density particles (non-magnetics) was simulated by altering the proportion of closing screen undersize bypass returning to the mill. Using a magnetic separator and a screen in the magnetics stream, different proportions of the magnetic fraction can be bypassed, thus allowing simulation of the effect of particle density on classification efficiency. This laboratory test work has confirmed that the impact of mineral density on cyclone efficiency subsequently has a crucial negative effect on ball mill circuit capacity. The results are in good agreement with reductions in capacity observed in practice. Multicomponent grinding and classification models were also developed in the LIMN software environment and were able to successfully simulate both the industrial and the laboratory ball mill circuit. The test and modelling procedures established in this project could be used for improved design of new magnetite ball mill grinding circuits as well as the optimisation of existing circuits.CITATION:Jankovic, A, Baguley, P, Valery, W and Holtham, P, 2015. Effect of mineral density for milling magnetite ores, in Proceedings Iron Ore 2015, pp 159–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Player, G Sweby

The material properties and hence performance of saturated alluvial sediments slope can be incorrectly forecast if the water content is not preserved, and materials properties not correctly determined. The occurrence of saturated sediments in the Western Australia (WA) Goldfields, while not common, should be a significant investigation focus. Geotechnical engineers new to the area may be unaware of this and hence the importance of correct testing and determination of the material strength. Application of appropriate analysis to determine stable pit slopes to an acceptable level of risk, is not possible unless the appropriate strength and hydrogeological parameters have been established at the outset. A back analysis is presented of a pit that had extensive slope failures in alluvial clay-rich sediments with discussion on the approach adopted by the original design engineers to assess pit wall stability and consequent poor slope performance. Learnings from a full pit 3D back analysis are presented, with an approach to geotechnical and hydrogeological investigations and analysis for slopes in similar materials.

Jun 22, 2022

The Rotary Kiln at TeKumi was commissioned in February 2002. The process involves burning limestone at 1000 - 11 000¦C to produce a burnt lime (CaO) product. This paper describes the design and installation of a trifoil system to improve the energy efficiency of the kiln. An energy balance showed that 32 per cent of the energy was being lost through the flue gases, compared to 5.8 per cent in shell losses and 2.5 per cent lost as heat in the product. The trifoil proved to be the best way to tap the energy from the flue gases. Drying tests showed that a trifoil improved the drying time of limestone by 37.5 per cent, compared to only 25 per cent for a lifter system. The trifoil system increases the surface area for heat transfer in a Rotary Kiln by 180 per cent. The overal energy efficiency of the Rotary Kiln was improved by 15 per cent, resulting in a 15 per cent increase in production and an 80¦C reduction in flue gas temperature. This has reduced dust build up in the ducting while reducing maintenance costs through a reduced fan speed. The trifoil hub was designed with tooths at the centre to prevent shifting. Each trifoil leg has an anchor block on the down side to prevent downward movement of the trefoil legs.

Jan 1, 2003

By W M. Tekano, T S. Coulter, N M. Hutt

The Vancouver Island Highway Project (VIHP) was a $CAD 1.2 billion expenditure by the Province of British Columbia to improve travel safety and relieve traffic congestion between Victoria and Campbell River on Vancouver Island. In the section of highway between the Tsolum River and Oyster River, on the Inland Island Highway portion of the VIHP, over half of the rock to be cut and filled was found to be net acid generating. The Tsolum River has been impacted by metal leaching and acid rock drainage (ML/ARD) for decades from an upstream closed minesite. Geochemical testwork indicated: over half of the rock along this section of highway was potentially net acid generating based on a site-specific SNPR (=NP/SAP) criterion of 1.5; some core samples were already acidic; pyrite occurred in disseminated framboidal and gel forms; the rate of acid generation was not high; measured neutralisation potential (NP) provided some lag time for the onset of net acidity; and non-carbonate neutralising minerals prevented low pH (These predictions led to ML/ARD controls involving: realignment of the highway; elevation control to minimise the volume of disturbed rock; encapsulation of blasted-rock fills within the highway, surrounded by low-permeability till and covered with asphalt; and diversion of water away from cut faces. Internal pipes drained any water reaching the fills into external ditches and ponds, where the water could be monitored and, if necessary, treated. Water from the cuts was also captured in ditches and carried to monitored ponds. Elevated aqueous sulfate concentrations in several ponds confirmed that sulfide minerals were oxidising, but the lack of both acidic pH and increasing trends in concentrations demonstrated that ML/ARD was controlled. Contingency plans for any pond that may become acidic include water treatment, which predictive testwork has shown would not require substantial amounts of limestone or lime.

Jan 1, 2003

By P Radulovic, V Lawson, M Muller, J Wallace

The Mount Isa Copper Concentrator was commissioned in 1973. Since commissioning some significant upgrades have been undertaken such as: • the replacement of the rod mill/ball mill circuit with AG mills and the subsequent conversion of the AG mills to SAG Mills. • the introduction of columns as retreat cleaners in 1987, then reallocated as prefloat cleaners in 1994 and rougher cleaners in 1996.• the repurposing of some rougher capacity to preflotation roughing to remove carbonaceous pyrite and talc in 1994.• the introduction of a Jameson Cell for preflotation cleaning in 2000. • the expansion of the rougher and cleaner circuits in 2002 with the inclusion of 6 x 100 m3 Wemco cells to replace the capacity lost to preflotation and to increase residence time and improve recovery. In 2013 work commenced to replace the cleaner circuit after 40 years of operation. The new cleaner circuit, consisting of 3 x B5400/18 Jameson Cells, replaced the rougher cleaner columns, cleaners, recleaners and retreat Agitair banks and was commissioned in Sep 2015. The new cleaner circuit was configured as two cells in series producing the final concentrate and a cleaner scavenger cell to supplement the existing Wemco cleaner scavenger cells. The performance of the new circuit is discussed.CITATION:Lawson, V, Muller, M, Radulovic, P and Wallace, J, 2017. Mt Isa copper concentrator cleaner circuit redesign, in Proceedings MetPlant 2017, pp 279–287 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By L Kempenaers, T van der Maten, U König, M G. C Zoontjes

Improving liquid blending operations in production plants is of paramount importance in many industries like mining, oils, petrochemicals and food. For accurate blending of different types of process streams, like homogeneous, heterogeneous, cold or hot streams, it is essential that the composition can be accurately monitored in real time. Advances in energy dispersive X-ray fluorescence (EDXRF) technology offers the possibility to apply XRF for online elemental analysis. In this paper we discuss an online EDXRF analyser for accurate blending control in many industries.EDXRF has the advantage that multiple elements can be measured simultaneously over a wide concentration range of wt per cent down to a few mg/kg, for elements between sodium (Na) and americium (Am) in the periodic table. To reach the desired accuracy and precision in an online XRF analyser, it is important to bring a representative and homogeneous sample of the process flow into the optical path of the analyser. The combination of a laminar flow cell design and advanced EDXRF technology leads to low detection limits and high performance. The obtained precision and accuracy allows for much tighter process control. In this paper we present two examples of industrial applications.CITATION:Zoontjes, M G C, van der Maten, T, Kempenaers, L and König, U, 2017. Online X-ray fluorescence spectrometer for accurate monitoring and improving blending sharpness in liquid production processes, in Proceedings Eighth World Conference on Sampling and Blending , pp 235–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By K Fiedler, A Newell, P D. Munro

Test work is the foundation upon which the success of projects and subsequent operations is laid, reflected in Professor Arthur Taggart’s pithy observation: ‘Make your mistakes on the small scale and your profits on the larger scale’. Indeed, Professor AllanTrench has succinctly noted that ‘Get the metallurgical characteristics wrong and you don’t have a project’.With deposits becoming lower grade, more structurally and mineralogically complex, final products requiring lower levels of impurities and tailings management demanding more attention, test work now assumes even greater significance in the acceptance and successful execution of a project. This paper is the first in a series aiming to stimulate thought on the metallurgical test work process by getting back to the fundamental basics through exploring and providing some guidelines for the metallurgical testing world, noting preferred practices as well as precautions and mitigations. This covers the key characteristics of metallurgical test work programs, including what needs to be done, sample selection, quality control and associated drivers, and most importantly, selecting, assessing and managing test work facilities. CITATION:Newell, A, Munro, P D and Fiedler, K, 2018. Metallurgical test work – between a rock and a hard place, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 15–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

The current talk of risk management as a separate discipline and management function is like earlier imposition of Quality Control (QC) as an overlay on shoddy production management. Risk management is vital, but is integral in the way we marshal our staff, make decisions, then monitor and review and make crucial secondary decisions. New leaders must not assume that hiring experts ensures good decisions. It is only the essential step one. The worst company I worked for had more expertise than the best. The difference was in culture and decision-making processes. Failed feasibility studies, persistent technical factions in a company that cancel each other, heaps of expert consultant reports piled up like a dump of bricks, even great but half-managers in large and small companies cancelling expertise at their disposal, are the worst manifestations. Just daily foul-ups are common even amongst smart people. We miners have made a great industry but are content to drift far below excellence, even where that word is bandied around. All the management literature and management courses will not right the situation û we have been sending budding managers to this good stuff for two generations and the effects are worthwhile but marginal. A few key ideals, ideas and slogans are not the way. These make inspiring books that work about as long as the Christmas spirit does in the real world. What we need is a coachesÆ manual and a standard of the essential package of culture and work processes that make excellence possible and show how to maintain it long term. It has not been written until now because most managers want to remain dilettante amateur managers without the discipline that creates excellence. First, believe excellence is possible and worth any effort; then commit to it.

Jan 1, 2007

By H Haghighi

Haul roads are often permanent unsealed access roads used by heavy haul trucks to transfer minerals. These roads can deteriorate rapidly which results in potholes, deformations and dust. Downer EDI Works has successfully provided efficient solutions to the mining industry to maintain their haul roads. HaulPac as a solution package is a process in which a bituminous emulsion is used to create a stable and durable pavement. The emulsion penetrates the road and binds the particles together, creating a stable base. It also seals the surface and prevents water from penetrating the underneath layers. Bituminous emulsion can increase the strength of the pavement material and decrease the road surface degradation which results in dust suppression. However, the everincreasing price of commodities, the necessity of reducing carbon emissions and the increasing use of autonomous haul trucks have made it vital to invest in novel maintenance solutions that can meet the needs of the mining industry in a cost-effective manner. This paper outlines the benefits of bituminous emulsion in terms of productivity, safety and environment followed by Downer’s approach to evaluate the suitability and to optimise the amount of product. The potential for changing the colour of the treated surface is explored and an initiative that incorporates end-of-life tyres of haul trucks into the pavement is introduced. And finally, an innovative method using artificial intelligence to estimate dust emission is presented.

Sep 18, 2023

By M Hawkes, Z Ji Gang, Z Ming, R Hassell

As underground mines become more geotechnically challenging with increasing depth and excavation size, the requirement for ground support to be installed as per design becomes more critical. The verification of installation quality for cable bolts and grouted rock bolts is difficult to assess. Current methods to control quality have limitations; pull testing is largely inconclusive with only extremely poor installation being identifiable. Audits during installation can only capture a small percentage of installed bolts. Following large rock mass displacement from either squeezing ground or seismic events, even previously well installed bolts may have yielded and require replacement. A method to provide an improved understanding of the reinforcement installation quality is Non- Destructive Testing (NDT) using acoustic reflection. To validate the accuracy of an NDT system, both plain and bulbed strand cable bolts were grouted in clear plastic tubes. The encapsulation grout quality was deliberately varied from full encapsulation through to partial encapsulation and a range of different size voids. The clear tubes allowed the ground encapsulation to be observed. Cable bolts strands were cut at varying lengths and different water cement grout ratios were used. Acoustic testing of the cable bolt specimens was completed blind; the technicians were not aware of what was being tested. The NDT results correlated well with the grout encapsulation, with differences between full encapsulation, minor voids and major voids being determined. The different water cement ratio and bolt lengths (including when partially cut) were also identifiable but with some discrepancies. Trials of the technology underground have also shown the data collection process to be relatively quick with each bolt taking 1-2 minutes to test, with interpretation of the results able to be completed soon after. The NDT results collected from the underground trial showed a wide variance in cable bolt grout encapsulation quality indicating that there were installation issues.

Mar 15, 2021