Search Documents

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Lawson F

A rotating disc geometry has been used to provide a uniformly accessible surface for a kinetic study of the cementation of the metals cadmium, lead and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu/Zn and Cu/Fe systems for which the rection rate was found to be completely solution-phase mass-transfer controlled. When the amount of material deposited was greater than 0.2 to 0.4 mg/cm2 there was an apparent enhancement in e which is attributed to the formation of a roughened deposit. This same phenomeon was obseived in the Cu/Zn Cu/Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass ,..~sfer controlled.

Jan 1, 1970

By Hocking G

For some underground structures, the use of the plane strain assumption in stress analyses may not be justified. The finite element method and photoelasticity have been used to obtain complete 3-D solutions, but, for various reasons, neither method has found universal use. The boundary integral equation method (B.I.E.M.) can be more efficient and economical than the finite element method for 3-D problems involving large volume to surface area ratios. A B.I.E.M. program developed for calculating stresses and deformations in infinite elastic media has been used to determine the 3-D distributions of stress around T- and Y- junctions of circular tunnels in stress fields in which the ratios of horizontal to vertical stress are 0, 0.33, 1.0 and 2.0. For the T- junction considered,stress concentrations at the intersection are approximately twice the plane strain values. Except where horizontal field stresses are high, the stresses in both tunnels approximate the plane strain values at about two tunnel diameters from the point of intersection of the tunnel centre lines. The stresses in the two branches reach those for the corresponding plane strain, two parallel tunnel case two diameters from the point of intersection of thq inner tunnel walls. Very high stress concentra- tions occur in the pillar of rock between the inner tunnel walls near the point of intersection.

Jan 1, 1976

By Takeuchi T, Matsugaki K

We have developed a new shotcreting which is suitable for the primary support of TBM tun- nelling in soft rock. This spraying compound is made from cement, a special accelerating agent and glass fiber. It can be sprayed on to a rock surface using a specially designed gun similar to paint-spraying equipment. Some of the characteristics of this method are as follows: 1) If spraying is done keeping the distance between the gun and the rock surface be- tween 0.2 and 3.0 m, the rebound losses are small and there is little dust. 2) This method can be used on excavated rock surfaces under inflowing water conditions of up to 10 i/m2òmin. 3) After 1 day the compressive strengthes of the sprayed material is greater than 250 kgf/cm2.

Jan 1, 1987

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988

By Kametani H

Since pyrite is a semiconductor, the relationship between the leaching rate and the semiconducting properties is of interest. In order to investigate this relationship, a pyrite concentrate (95% FeS2) was oxidized at 90¦C (363 K) in an acid solution containing 100 g/dm3 H2SO4 and 1.0 to 25.1 g/dm3 total Fe. The suspension potential (Pt vs. SCE) was maintained at the desired values, within the range 0.40 to 0.70 V, by controlled additions of a KMn04 solution during leaching. The results were analyzed using a simplified kinetic expression. The rate constant was independent of the Fe concentration, while it increased with suspension potential. Partly oxidized samples were then prepared at varying fractions of reaction. After removing the elemental sulphur formed, they underwent thermoelectric power measurements using a packed bed lying in a temperature gradient. The value of thermo- electric power increased from about 0 to 30 pV/K in the early stages of oxidation. The results obtained are compared with those for chalco- pyrite reported in a previous paper.

Jan 1, 1987

A Kellogg type computer model of the slag fuming process is applied in reverse to derive some thermodynamic properties of components in lead blast furnace slag. At 1200¦C, the average activity coefficients calculated were 3.40 (S.D. 0.50) for ZnO referred to the pure solid; 0.657 (S.D. 0.022) for PbO referred to the pure liquid; for the ratios y 3.175 y (referred to the Feo.9450, Fe304 pure solids) 4.19 (S.D. 1.15), and for yCaS/ 1CaO (referred to the pure solids) 5.10 (S.D. 2.96). Statistical relationships were derived for these activity coefficients and ratios as functions of the composition of slag, which contained in molar percentages 1.9 - 12.6% ZnO, 19.8 - 24.9% Fe0.9450, 0.9 - 1.6% Fe304, 0.002 - 1.9% PbO, 16.1 - 18.6% CaO, 25.9 - 31.0% SiO2, 4.8 - 5.5% MnO, 9.2 - 10.3% A101.5, 1.2 - 1.4% CaS, and 5.1 - 9.6% "Mgo" (the balance).

Jan 1, 1980

A mechanised sub-level overhead benching method is used at Cleveland, to produce 22,000 tons per month of ore assaying 0.92% Sn and 0.40% Cu. The ore occurs in a series of vertical lenses which can be mined by open stoping. Levels are developed at 60ft., vertical intervals by jumbos. The ore is silled out and the stope block formed between levels drilled out by long hole drilling. Each row of holes is fired and broken ore within safe reach from the stope brow is mucked out by Wagner ST-5A Scoop Trams. The remaining broken ore is recovered on extraction of the next lower level. Ore is hauled by road to the crusher station from the mine. As mining proceeds below the lowest surface portal a spiral decline will be used for ore haulage and mine servicing.

Jan 1, 1970

By R Dwyer

Iron ore currently mined in Australia generally requires very little beneficiation. However, depleting high-grade resources means that in the future low-grade iron ore deposits will need to be mined to meet the increasing demands of the global steel industry. Along with the increased demand, the industry faces additional pressure to reduce the environmental impact of mining and mineral processing. This has stimulated research beyond incremental improvements to conventional processing into alternative low-impact processes, including biotechnological approaches to mineral processing.Bioflotation and bioflocculation have emerged as relatively recent technologies, in which bacteria and/or their extracellular material may be used as flotation reagents (collectors or modifiers), enabling improved selective separation of minerals. The primary advantage is the production of a selective, environmentally-benign alternative to conventional flotation reagents. A biotechnological approach may also be taken in the beneficiation of high-phosphorous iron ores utilising bacteria capable of iron reduction and phosphorous solubilisation.Samples from three iron ore deposits in Western Australia were examined for bacteria suitable for iron ore benefi ciation. A number of common soil microorganisms including Pseudomonas spp, Limnobacter thiooxidans, Paenibacillus spp, and Ralstonia insidiosa were identified using culture-independent molecular techniques. A number of anaerobic species belonging to the genus Clostridium were also identified in the core samples. Selected aerobic species were enriched and isolated on high nutrient media in the presence of haematite. Several of the isolated strains showed an affinity for iron ore, attaching to haematite in enrichment cultures and further demonstrated through adhesion studies. Other isolated species such as Ralstonia isidiosa and Pseudomonas stutzeri are known to solubilise rock phosphates in soils and have potential for the removal of phosphorous from Australian iron ores.

Jul 11, 2011

In reviewing recent developments in the process mineralogy of gold it is convenient to distinguish between visible (>0.1 pm) and invisible gold (1 - 2 pm in size in polished section; these can scan the surface of a polished section, identifying the gold minerals, recording co-ordinates of the grains for subsequent examination, and making measurements of areas and sizes of the grains. However, problems of sample reliresentivity in polished section mean that such data may not give good quantification of gold mineral proportions and liberation/locking characteristics and other methods are required for this (amalgamation, cyanidation, ultra-fine milling and cyanidation). Characterisation of invisible gold in bulk material (eg a sulphide concentrate) can be done by mineral separation, ultra-fine milling and cyanidation or by quantitative point analyses of a large number of mineral grains. Analytical methods include electron microprobe analysis (detection limit normally -200 ppm but -10 ppm by using special techniques), ion microprobe analysis (secondary ion mass spectrometry - SIMS; detection limit -0.2 ppm) or proton microprobe analysis (PIXE; detection limit

Jan 1, 1992

The paper highlights the conceptual developments in rock mechanics applied to quantify the effect of bolts in the stabilization of joints and yielding soft rocks. NOTATION Aa = stress change after excavation Eä EE, Eä = moduli of intact rock, single joint and jointed rock Eb = elastic modulus of the bolt k, = normal stiffness of joint Ab = cross section area of the bolt A, = area of influence per bolt ab = axial bolt stress e, = axial strain of the bolt eä e,, ej, = strains of intact rock, joint and jointed rock Ai = area of the joint ,r+ = shearing resistance of the bolt (at the joint) a = normal stress at the joint plane aäa3 = major and minor principal stresses c;, 4i; = cohesion and friction angle of the joint 0 = angle between the bolt and the joint a = inclination of the joint to the vertical axis P = bolt density parameter u, = convergence of unsupported tunnel section u, = convergence of bolted tunnel

Jan 1, 1992

The Ok Tedi Project has been planned as a selective mining operation since the Feasibility Study. The nature of the orebody, and the need to 'stage' the infrastructure buildup meant that initially the mill would process gol ore using a leach-CIP process, followed by parallel leaching of gold ore and flotation of copper ore, and finally all flotation of copper ore. Cutoff grades were applied to gold and copper ore of 1.0-1.3 g/t Au and 0.4-0.3% Tot. Cu. Since startup, unpredicted occurrences of sulphide copper and, to a Lesser extent, carbonaceous material, has necessitated significant additional short term drilling (other than at grade boundaries), and shift grade control in the pit to control contaminant levels. Remodelling of the orebody based on the most up to date variography and geological interpretation has had a significant impact on the reserves, and thus the whole project development strategy; necessitating the earlier processing of copper ores, and preflotation of the gold ore.This paper discusses some of these points in detail, and in particular highlights how unforseen geological occurrences coupled with processing restrictions can have significant impacts on ore reserves and the mine development schedule.

Jan 1, 1986

Silica and limestone fluxing levels in copper smelting slags were studied. Copper concentrates with flux additions were smelted to matte (55.5 per cent Cu) and slag in a pilot scale submerged combustion furnace.Results indicated that oxidic and sulphidic copper levels in slags were minimised with a slag Si02 level of 36 per cent and a SiO2/CaO ratio of 5.5. Total copper losses in slags were 0.6 per cent under these conditions.To produce the desired slag chemistry, additions of bulk silica and limestone to copper concentrates of fluctuating grades were predicted numerically. The method employed the solution of two simultaneous equations, each respectively for silica and limestone calculations.The predicted flux additions were applied in a further series of tests and the resultant stages were found to be satisfactory. The method is applicable to smelting 'operations which employ two flux bins, with weigh feeders, so that slag chemistry may be controlled with the flux/concentrate feed mix.

Jan 1, 1985

By S Jahanshahi

In an earlier LCA study, the authors showed that the electricity consumption of the electric furnaces used in the production of the ferronickel and ferrochrome feedstocks made significant contributions towards the Gross Energy Requirement (GER) of stainless steel production, on a æcradle-to-gateÆ basis. Given the relatively low efficiencies associated with electrical power generation, substantial reductions in the GER for stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel and ferrochromium smelting stages.In view of these findings, a follow-up study was undertaken to investigate the likely environmental benefits of using bath smelting processes for the production of ferronickel and ferrochromium compared to the traditional rotary kiln-electric furnace processes, but still utilising the electric furnace process for stainless steel production. The METSIM process simulation software package was used to set up models of the two bath smelting processes and provide process energy requirements that were incorporated into the LCA. The environmental impacts considered in the LCA were greenhouse (Global Warming Potential, GWP) and acid rain gas (Acidification Potential, AP) emissions and solid waste emissions.The results of the study showed that the bath smelting route reduced the GER for ferronickel production by about 37 per cent over the traditional route, which translated to about a 21 per cent reduction in the GER for stainless steel. The corresponding reduction for ferrochromium was about half that for ferronickel, and when combined with the ferronickel result gave a 25 per cent reduction in the GER for stainless steel production. Similar reductions were also observed for the GWP and to a lesser extent the AP for both feedstocks, as all primary energy inputs were essentially fossil fuel based. Substantial reductions in solid waste emissions were also indicated for the direct use of ores in smelting. By utilising bath smelting processes for the production of the ferronickel and ferrochromium feedstocks, stainless steelÆs suitability for meeting many of the goals necessary for sustainable development, already recognised because of its particular properties, would be even further enhanced.

Jan 1, 2004

By L Cooper, J Sharma, M J. Hendry

Thick clay tills below potash mine tailings and brine ponds are important natural barriers protecting fresh water aquifers in Saskatchewan. Centrifuge modelling was applied to assess geochemical processes and impacts of dilute brine (0.1 M NaCl) migration through clay till core samples obtained from non saline, unoxidised clay till at a mine site. At accelerated gravity of 876 + g, during each day of centrifuge modelling, flow driven through a 52 mm length core simulated transport through a 45 m thick clay over ~2100 years. Hydraulic conductivity, monitored continuously before and during brine permeation, was low and relatively constant (8.5 + 10-12 m/s), confirming that confining stresses prevent permeability increase. Core density and porosity measurements confirmed that reactive transport occurred under realistic in situ conditions. Breakthrough (defined by C/C0 = 0.5) of non-reactive Cl- occurred at 25 days. The slight delay for Na+ breakthrough, associated with small increases in Ca2+ and Mg2+ concentrations in the effluent were attributed to ion exchange, but carbonate reactions were relatively unimportant. Cation exchange analysis of core samples was inconclusive without corrections for porewater Na+ and carbonate dissolution. Geochemical processes that were observed during centrifuge modelling were successfully simulated using the 1D geochemical transport code PHREEQC. Solute transport was dominated by diffusion with limited ion exchange to delay Na+ migration. Brine would not break through a 45 m thick clay for tens of thousands of years. Based on these findings, the thick clay till at this site, if laterally extensive and undisturbed by drilling activity, is likely to act as an effective natural barrier to vertical brine migration over the long term.

Jan 1, 2003

By R A. Pax

Electrostatic separation is a core requirement for the beneficiation of mineral sands suites to provide valuable product. Although the basis of electrostatic separation has been understood for some time, the details required to be able to calculate the metallurgical performance of a separator has not previously been achieved from a mechanistic perspective. Empirical models have had some success but require extensive test work. Traditionally, performance of an electrostatic separator is determined by careful experimental work using the target mineral suite. Although electrostatic separation was invented at the end of the 19th century, very little modification of the basic equipment occurred until relatively recently, with the addition of a plate electrode to aid separation. Previously, the author has presented results, calculated using finite element modelling (FEM), of the electric fields present in an electrostatic separator in various configurations. This paper will present some new mathematical modelling work, which uses the FEM determined electric field configurations but also incorporates some fundamental physical processes that provide insight as to the limitations and opportunities for this important separation technique.

Oct 5, 2011

By Takiuchi T, Kurita M, Owada S

This paper describes the possibility of the application of flotation to the separation of monazite from xenotime and of columbite from ferberite, which have been said to be difficult with generally used physical beneficiation methods. For Malaysian monazite and xenotime samples, a great difference is observed between the flotation recoveries at pH 7.5 using 1.0 x 10-4mol/1 dodecylammonium chloride (DAC). The grade and recovery of columbite in the binary flotation with both minerals result in 85 per cent and 67 per cent in the cleaning froth and 91 per cent and 51 per cent in the re-cleaning froth, without adding any scavenging stages. For monazite samples from various localities, the flotability is dominated by the electrostatic interaction between mineral surface and collector ion using DAC as collector, but the singular decrease of flotation is observed in the sample of which the crystallinity is low and the surface structure is rugged and complex. Otherwise, ferric ion in the flotation system probably dissolved from mineral is found to activate the flotation using sodium dodecylsulfate as collector. For columbite and ferberite, the separation is judged possible at pH 3.0 using 1.0 x 10'3mo1/l sodium oleate (NaOl) from the single flotation results of each mineral. In the binary flotation, however, columbite recovery in the froth is greatly diminished below that expected. This would be because NaOl is prevented from adsorbing on the columbite surface of which the charge is transformed more negative side by the specific adsorption of the tungstate ion dissolved from ferberite.

Jan 1, 1993

By Waladan M, Elliot B, Rankin W. J

A survey was undertaken on the Kalgoorlie Nickel Smelter in which samples of slag and matte were taken along the length of the integrated flash smelting furnace and analysed to determine the variation of nickel and iron concentration. At the same time the oxygen potential of the slag and matte was measured using disposable tip solid-state oxygen probes. The results show that the oxygen potential of the slag is higher than that of the matte and that both decrease from the reaction shaft end to the slag tap hole end of the furnace. The slag and matte are not at equilibrium except towards the tap hole end. Reduction of nickel and magnetite from the slag occurs before the slag enters the slag-cleaning appendage by reaction with iron in the matte. Thermodynamic modelling and laboratory experiments showed that the equilibrium nickel and magnetite contents of the slag in the absence of a carbonaceous reducing agent are about 0.4 per cent and 7.5 per cent, respectively. A carbonaceous reductant is required to obtain a lower nickel content in the slag.

Jan 1, 1991

A nine-month investigation was conducted into the effect on coke quality and blast furnace operation of the addition of bentonite and southern coal to the northern coal fed to the coke ovens at the Newcastle steelworks.Additions of 0·3 per cent bentonite or 25 per cent southern coal to the northern coal increased the coke strength from 15-20 A.S.T.M. stability to 25-30 A.S.T.M. stability. It is likely that improved mixing and blending facilities would, in both cases, give a coke of over 30 A.S.T.M. stability.For the same coke strength, the use of 0 3 per cent imported Wyoming bentonite was considerably cheaper than the use of 25 per cent southern coal, but the use of Australian bentonite promises the same coke strength for still lower costs. Other additives such as coke breeze, charcoal, iron ore fines, and certain other finely divided materials, gave relatively minor improvements in coke quality.There appeared to be sufficient improvement in blast furnace operation and production to justify full scale addition of bentonite to improve coke quality, although other variables, particularly iron ore physical quality, overshadowed on many occasions the effect of coke quality. Further coke trials with southern or bentonite will be carried out when ore quality has been improved by the introduction of ore sintering at Newcastle.INTRODUCTIONDuring the period of operation of the Newcastle coke ovens and blast furnaces from April 1960 (when No. 3 blast furnace was blown in after rebuilding) to December 1960, a bentonite coke trial was carried out based on earlier research findings (Gregory, 1959a, 1959b; Felton and Gregory, 1960; Gregory, 1960) that as little as 0 3 per cent to 05 per cent bentonite clay added to northern N.S.W. high volatile coking coals gave a significant increase in coke strength. The bentonite coke trial was followed by trials...

Jan 1, 1962

The design of mine ventilation systems for the BHP Steel Division Collieries is based on the acquisition of ventilation survey data for the establishment of a realistic computer net- work model. The branches which form the net- work for the computer models are calculated from a range of resistance factors incorporat- ing both a frictional and shock loss component. Since shock losses can account for up to 30 per cent of the total energy losses in mine airways the use of friction factors alone without accounting for shock losses will result in the choosing of an insufficiently performing fan. Published tables of friction factors have in- variably been taken from metalliferous or single entry studies and consequently are not reliable for Australia's mining conditions where multiple entries with regularly spaced cut-throughs are the normal practice. Typical resistance factors for roadways of rectangular cross-section 5.5 m x 2.0 m, with coal sides, have been found to vary from 0.11 Ns2/m8/km where no timber supports are used, to 0.98 Ns2/m8/km where double centre legging together with wooden chocks is used. In addition to the range of resistance factors due to varying support methods, the nature of use for a roadway is very significant because of the condition of repair and upkeep maintained.

Jan 1, 1983