Search Documents

By Thirumalai K, Peluso R. G

The United States has more than 45 billion tons of economic coal reserves in seams above 10 feet thick and current underground production from thick seams represent less than three per cent of the total production. A tripling of underground production from thick seams is necessary within the next 10 years to meet U.S. coal production demands. An analysis of underground accident and production data is presented in the paper. A study of accident and injury distribution in different coal seam heights in the eastern and western part of the United States in seams ranging in thicknesses from 5 to 15 feet indicates that the seam thicknesses do not produce adverse impact on underground injury incidence. Accidents associated with roof falls and haulage account for about 70 per cent of underground mining injuries.

Jan 1, 1976

By Doyle P, Mulroney D

The Cassidy Shaft was sunk to access the Mount Charlotte and Reward Orebodies below the Flanagan Fault. The 1,184m deep shaft is concrete lined to 6.5m diameter for its full depth. The initial 590m was excavated by stripping into a 1.8m diameter borehole and hoisting the broken material through the existing mine. The remaining 594m was excavated by conventional shaft sinking methods. The shaft was sunk through 3 existing plats and an additional 8 plats cut. 1,800 tonnes of steel and 8 cables were installed during the furnishing of the 4 compartments.

Jan 1, 1985

Traditional vat leaching has been done on a batch basis, which involves loading the vats, leaching, drainage, washing, draining again, and unloading. As a result of these many steps and the attendent cost of labor, vat leaching is generally not an economic proposition. Also, like heap leaching, there is a tendency for channeling to occur within the bed, whether the leach solution flow is by percolation upwards or downwards. No doubt experimenters over the decades have been enticed by the idea of fluidization induced by upward flow through the ore bed. If the bed could be fluidized, then a continuous flow of material could be set up, dispensing with the high cost of loading and unloading the vat. A quick calculation of solution flow requirements, however, soon reveals that the volume of constant liquid movement necessary to sustain fluidization is prohibitive from a power and cost standpoint. The premise of the Mackie Vat Leaching Jig (MVLT) concept was that the large volume of liquid flow required for fluidization could be achieved instantaneously, and that during this small element of time, the solids would flow under the influence of the hydraulic gradient in the vat. If this procedure could be repeated in a cyclic manner, then a steady-state condition could be set up. Experiments in the laboratory demonstrated that solids flow could be achieved in this manner.

Jan 1, 1991

By Large RR

Underlying the 15 million tonne, high grade Hellyer volcanogenic massive sulphide deposit of western Tasmania is an extensive, well developed, and well preserved stringer system. Pervasive alteration of the footwall mafic volcanics occurred as the hydrothermal system initiated. Mineralogical zoning exists within the footwall alteration pipe, with a central siliceous core giving way to zones of chlorite, chlorite-carbonate, sericite-chlorite, and finally sericite-quartz on the margins (stringer envelope zone). However, the alteration morphology and zonation is not symmetrical around the central siliceous core; eastward the alteration zones are steeply dipping and terminate abruptly under the massive sulphide, while westward they extend out under the ore body in a blanket fashion. Geologic evidence indicates that the pervasive alteration started with the development of sericite-quartz which was subsequently overprinted by chlorite and finally quartz-sericite as the hydrothermal system became focused towards the centre of the stringer system.

Jan 1, 1990

Open pit mines in the Yilgam Craton have unique hydrogeological characteristics resulting from a combination of geology, mineralisation and the complex and extended development of the regolith. The principal features of this geological relationship are:ò deep and complex multi-stage development of the weathering profile; ò steeply dipping rock layering;ò supergene enrichment; andò mining across the regolith/rock interface.These features result in large changes in permeability horizontally across rock layers; vertically through the weathering profile and along-strike in association with mineralisation and the mineralised Structure.

Jan 1, 1993

Probabilistic seismic hazard analyses (PSHA) have now gained wide acceptance in the development of design criteria for major projects. When used with regional criteria the procedures have also allowed the preparation of more rational seismic zoning maps. Seismic zoning maps using various levels of results from PSHA studies around the Pacific Rim now include Canada, Indonesia, New Zealand and the United States. Some Pacific Rim countries such as Chile where the seismic exposure is dominated by subduction events have no subdivision into separate zones.Approaches to risk based zoning are being considered in several Pacific Rim countries including Australia. Australian studies must face problems similar to parts of the Eastern United States where seismic activity is low with irregular and infrequent occurrences of moderately large earthquakes. The perception of the seismic exposure by both regulatory agencies and the public at large is different when considering areas of low seismicity. There is therefore a need to make different interpretations of the results of PSHA studies in these areas of low seismicity. The aim of this paper is to explore some of these differences by comparing the results from two site specific studies from areas with widely differing seismic activity rates.

Jan 1, 1990

By Sataev IS, Malinovskaja ND, Otrozdenova LA, Knodov NV, Maximov II, Kuznetzou OK

The technology of flotation recovery of silver from the residue of a zinc plant is described. The peculiarity of this technology is a preliminary pulp conditioning in sodium chloride solution in the presence of aluminum metal under high temperature. In this process the silver is converted to the metallic phase and then floated with the usual sulphydryl collectors. A variant using a combined technology is also described, in which before flotation is performed about 50 per cent of silver is leached. The total silver recovery with the combined technology comes up to 90 - 94 per cent.

Jan 1, 1993

By G Bournival, Y Saavedra Moreno, S Ata

Flotation frothers are heteropolar molecules that are preferentially adsorbed at the bubble interface to enhance the flotation performance by promoting the formation of small and stable bubbles. Frothers have different characteristics that can be used to classify them. A classification framework has been recently presented by Saavedra Moreno et al (2022) to classify non-ionic frothers by conducting a principal component analysis (PCA) and a hierarchical clustering analysis (HCA). However, for the purpose of the present research, only five frother characteristics, including molecular weight (MW), hydrophile–lipophile balance (HLB), critical coalescence concentration (CCC), the minimum Sauter mean diameter (DL), and foam stability index (DFI) were used in the PCA and HCA. All those characteristics were evaluated for a two-phase system in the absence of particles. Realising the important role that particles play in froth stability and behaviour, the effect of hydrophobic particles on the presented frother classification framework was investigated in this study. Four frothers with different characteristics, methyl isobutyl carbinol (MIBC), 1-pentanol, tri (propylene glycol) (TPG), and tri (propylene glycol) methyl ether (TPM), were chosen. The experiments were carried out in the presence and absence of silica particles esterified with 1-pentanol. It was evident that the results for 1-pentanol, TPM, MIBC, and TPG in the three-phase system agreed well with the frother classification presented for the two-phase system as frothers were clustered in the same groups. The findings from this research support the use of the frother classification system presented in two-phase system to select a specific frother for a particular application without the necessity of conducting laborious experiments in a three-phase system.

Aug 24, 2022

By Abbott T. M

Alcoa of Australia operates three Alumina refineries in the South West of Western Australia at Kwinana adjacent to the South suburbs of Perth and at Pinjarra and Wagerup in rural settings 100 and 150 kilometres south of Perth respectively (see Figure 1). Alcoa's total alumina production is currently around five million tonnes per annum and this will increase to 5.5 million tonnes by early 1990. Further expansion of production is likely if current world aluminium demand trends continue. Alcoa's refineries utilise bauxite mined in the nearby Darling Range which is low grade by world standards having around 32 % by weight extractable alumina (by comparison Weipa bauxite yields around 55% alumina). This means that for every tonne of alumina produced two tonnes of solid wastes remain and therefore while we in Western Australia can boast of hosting the largest alumina industry in the world with around 18% of total world production we suffer from having the lion's share or 40% of the world's bauxite residues to dispose of. In its Western Australian setting the management of these residues in a manner which is acceptable to the community creates many challenges. These are primarily due to the mass and volume of waste produced, its chemical and physical characteristics and the environmental features of the local area including close proximity of neighbours, competing land uses and the presence of natural resources such as surface water and groundwater. In addition the trend towards more stringent statutory environmental controls and greater political and community awareness of environmental issues means that we must be able to demonstrate improvements that will reduce the considerable adverse impacts of past practices. Of course we must also try to keep the overall cost of residue disposal as low as possible to maintain our competitiveness with refineries which may have much smaller volumes of waste to dispose of and less environmental constraints.

Jan 1, 1989

By Gibbons S. L, Ritchie I. M, Murr D. M

Fundamental studies on the transformations of iron oxides have been carried out and related to the solution conditions in the Becher process. The results show that a number of iron oxide interconversion reactions occur in the aeration reactor with the products depending on the pH, temperature and oxidation potential of the aeration liquor. It is concluded that the lack of process control in the aeration reactor of the Becher process significantly hinders the ability to predict and produce high quality single phase iron oxides of a consistent colour.

Jan 1, 1990

The Rosebery Mine on the west coast of Tasmania is a world class polymetallic base metal deposit, containing six major minerals: galena, sphalerite, chalcopyrite, gold, silver and pyrite. This resource has been exploited for nearly a century, yet a reliable estimate of the reserve continues to present a challenge.Over the past twenty years, the operation has changed from relatively low productivity cut and fill timber-support scraper mining, to higher productivity bulk mechanised open stoping. At the same time, economic constraints have changed and grades have fallen, which have increased the pressure to refine the resource/reserve estimating processes. This paper compares the restrictions of the polygonal section method of the past with the advantages of a kriged block model. The limitations of Mine Call Factors, the problems involved in converting decades of diamond drilling data on paper into a computer data base, and the effect of this new methodology at Rosebery, are described.

Jan 1, 1990

By Stevenson I, Dickinson W, Taylor R. N

Despite flash smelting's widespread use little is known about the actual processes taking place in flash furnace shafts and comparatively few reports of sampling campaigns have appeared in the published literature. his paper reviews the previous reports of the use of horizontal trough samplers and analyses their expected collection efficiency. In the light of the deficiencies revealed by this analysis an isokinetic sampler was produced and a vertical sampling technique was also developed to obtain samples from directly below the burners in the shaft of the flash furnace at the Kalgoorlie nickel smelter. Comparison of the sizing of the samples obtained with the horizontal trough and isokinetic samplers confirmed the theoretical analyses and showed that the trough samplers were not collecting the fine particles. Besides providing data to validate mathematical models of the burners and shaft, chemical analyses of the shaft samples showed that the coal in the charge was reacting preferentially and that the plume of at least one of the burners was being deflected from its axial position. In the region directly below the burner there was evidence that the disperser on the burner was imparting more momentum to the coarser particles and that these were concentrating in the outer regions of the particle plumes issuing from the burners.

Jan 1, 1992

By D E. G Connelly, K Y. Wong

Gold at the Harbour Lights Mine (HLM), WA occurs principally in pyrite (Py) and arsenopyrite (AsPy) minerals rendering it inaccessible to direct cyanidation. Froth flotation produces a concentrate with low mass recovery and with high recoveries of sulfides. After investigating several alternatives, a novel flotation process has been developed to separate the concentrate into pyrite and arsenopyrite rich fractions. The pyrite fraction is finely ground and cyanide leached, while the arsenopyrite is treated off-site. This paper describes the separation process from laboratory bench scale through to commercial operation at the HLM gold plant.

Jan 1, 2005

Commencing from a platform acknowledging the capability of the Russian mining industry in open cut and underground mining operations a revitalisation of the industry will depend on an assimilation of mining economics and on an opportunity for technical training of Russian mining industry professionals.Successful foreign investment in parallel with the reconstruction of the industry rests on an understanding of culture, history, internal controls under central planning, and external factors affecting mining development.

Jan 1, 1997

The outlook for suppliers of energy to the expanding economies of the Pacific Basin region is essentially positive, but particularly for exporters of high quality steam coal. This paper argues that economic growth in the Pacific Basin region has exceeded world economic growth for some years and that this will continue to be the case for the next decade at least. It looks briefly at the link between economic growth and energy demand and at the relationship between energy demand and the demand for electricity.Changing preferences in fuel mix for electrical generation in the region are noted and tentative forecasts made about variations in this mix. The pros and cons of various forms of fuel used to generate electricity are considered from the point of view of the consumer.

Jan 1, 1990

By Sharpin PC

The countercurrent gas-solid-heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temp-erature distributions through the drier have been calculated. Although the calculations rest on several simplifying assump-tions, to be corrected as the experimental work develops, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating con-ditions on the rate of drying of the briquettes which-controls the 2 strength of the char produced. The analysis shows why a limitation was reached in the improvement of char-strength in the pilot plant in 1961 and a prediction is made of ' a way ' in ' which the limitation could be overcome.

Jan 1, 1963

By Richmond A

Like many industries the coal mining industry has, since the beginning of this century, undergone many changes. Technological advances and the increasing demand for fossil fuels have introduced new mining methods and techniques which allow the extraction of thicker and deeper coal seams at higher rates of production. Most new methods of mining (or for that matter any other processes) introduce problems which the engineers of the industry are expected to face and resolve. Unfortunately, spontaneous combustion has plagued the coal mining industry since the first attempts to mine coal, and is no doubt partly responsible for the reputation that coal mining is a hazardous industry. The financial loss and toll of human lives due to the occurrence of spontaneous combustion of coal in coal mines is enormous, if not incalculable. Its occurrence today is less likely to claim lives, due to both improved methods of working and in the detection of spontaneous combustion sites.

Jan 1, 1983

A review of the factors controlling stope wall behaviour such as excavation geometry, rockmass strength, induced stress, ground support, blast damage and drill drive layout is undertaken. In addition, the advantages and disadvantages of single lift stope geometries linked to vertical crater retreat are also analysed. Finally, key components of multiple lift stoping such as cut-off slots, production rings, stope undercuts and drawpoints are studied in detail.

Jan 1, 2000

The occurence of high silver values in the oxidised zone of the main lode at Broken Hill is well known as a large factor in achieving the early fame of Broken Hill, and the minerals of this zone form a long list, which has been tabulated by G Smith*, and includes...

Jan 1, 1926

By Wilkins L. G

Ore recovered by North Broken Hill Limited as a result of mining operations at its Broken Hill leases is obtained, at the present scale of working, in the proportions of 80% from the North mine and 20% from the British mine sections, and is composed mainly of a silver bearing, sulphide lead and zinc mineral, in association with the gangue materials mentioned later in the text.The lead-zinc sulphide lode at the North mine is deposited in folds in pre-Cambrian sedimentary schists. These folds pitch north-east at approximately 40° and dip north-west at approximately 60°. In plan the deposit appears as two lenses designated on the mine as the "Southern" and "Northern" ore-bodies.The Southern ore-body yields the main tonnage of crude ore. The sulphide mass here overlies a heavy layer of rhodonite which persists with the pitch of the lode. In the central section of this ore-body the sulphide zone is coarse grained and of high grade with a wide range of minerals in the gangue dilution. Quartz, garnet, ftuorite, rhodonite, and felspar are common, whilst chalcopyrites, pyrites, pyrrhotite and green felspar are often present. The Northern ore-body is dolomitic to siliceous in nature. Crude ore obtained from the British section is predominantly...

Jan 1, 1940