Search Documents

By G. L. Craig

COPPER containing a small amount of arsenic has been used extensively abroad, and a number of reports, particularly those by English workers, have indicated that such copper is better suited for certain uses than high-conductivity copper. Inasmuch as a large percentage of the copper fabricated is used for nonelectrical purposes where high conductivity is not at all essential, it has been suggested that arsenical copper might be at least as suitable as high-conductivity copper for many purposes. An investigation spon-sored by the Calumet & Hecla Consolidated Copper Co. at Battelle Memorial Institute was therefore undertaken with the object of determin-ing the effect of small amounts of arsenic (up to 0.75 per cent) on the properties of copper. In this work the effect of arsenic on the basic properties of tough-pitch and of phosphorized copper have been critically studied and many data collected from laboratory experiments which have been supplemented by mill-scale tests. The results of these tests, with coppers of the type referred to, in the annealed condition and after various degrees of reduction, show that the basic properties of copper are not greatly affected by small amounts of arsenic, an increase in strength being observed with increasing arsenic with no corresponding decrease in ductility. It is well known that the evaluation of material for plastic deforma-tion, on the basis of laboratory tests, may not be directly comparable with its performance in commercial operations. In order, therefore, to substantiate the data obtained at the Institute, the cooperation of the Wolverine Tube Co. was obtained for a series of production tests on the fabrication characteristics of phosphorized arsenical copper in the manu-facture of seamless copper tubing. In these tests the behavior of the arsenical coppers was carefully observed in comparison with that of representative types of phosphorized arsenic-free copper, which were fabricated under the same conditions.

Jan 1, 1933

By T. W. Guy

THE increased moisture due to water¬spraying for coal dust control is of interest even for mines from which the coal is to be wet-washed before screening, because in many cases wet coal dust materially decreases the loading efficiency of men an equipment at the faces. It also causes serious increase in the normal wear and deterioration of all equipment with which it comes in contact. It is important to the consumer if it increases his as-receive moisture. No attempt will be made in this paper t cover the entire subject of water-spraying of coal for dust control. It will be confine to discussion and data on (r) percentages c dust in bituminous coals, (2) moisture increases due to spraying for dust control in mines or plants by methods which have proven satisfactory for periods of one to five or more years, and (3) a few suggestions for research. SIZE AND PERCENTAGE OF COAL DUST The U. S. Bureau of Mines1 classifies a coal dust all bituminous coal passing 20-mesh sieve (0.0328 in. square opening; The percentage of such dust to be found is ROM coal, of course, varies widely wit. the characteristics of the seam, and with the methods used in the mining and in the preparation of the coal. ROM screen analyses of 12 U. S. coals selected at random from personal files given in Table I show: A few other screen analyses examined indicating 40 pct or more of 2o-mesh X o dust in 3/8 in. X o-sizes were not included because of uncertainty that they were representative. The number of results in Table I is not sufficient to give a reliable estimate of the average, or of the range to be expected, but it indicates that in every case the coal dust is a relatively large percentage of the total ROM coal, and, of course, a progressively larger percentage of resultants as the larger sizes are separated for marketing.

Jan 1, 1948

By L. G. Carpenter, D. E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO,. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley. The deposit is believed to be made up of salts present in the runoff waters from the last two ice stages. Searles Lakes was the third in a chain of five lakes that received waters from the Owens Valley drainage of the Sierra Nevada Mts. After leaving Owens Lake the waters could flood in succession into the Indian Wells, Searles, Panamint, and Death valleys (Fig. 2). During the first two ice stages of the Pleistocene Epoch most of the waters eventually arrived at Death Valley; consequently the lower 3300 ft of Searles Valley contain only mud

Jan 1, 1960

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

BURKE BAKER, Philadelphia, Pa. (written discussion*).-The small briquetting plant of the American Briquet Co., at 25th Street and Washington Ave., Philadelphia, was built primarily as a demonstration plant. Its output per hour is 4 tons of 2-oz. briquets, which have been retailed in the, vicinity during the year the plant has been in operation. They have proved very acceptable for use in ranges, heaters and grates in-home, and in steam heating plants in apartment houses and hotels. They have not been sold for power purposes, although satisfactory tests have been made in. this field. Anthracite silt is used and is shipped direct from breaker or washery, the only preparation it receives being the removal f excess moisture by means of a Ruggles-Coles rotary dryer. Care is taken, however, to purchase silt containing less than 18 per cent. ash. The method is covered by U. S. Patent No. 941454, issued to Chas. E. Hite, and is known as the "emulsion process." The binder, which is the, basis of the patent, is composed. of 0.5 per cent. cornstarch or wheat flour; 1 per cent. asphaltum or hydrolene, and 6.5 per cent. water, on the weight of coal dust. It is prepared in a tank equipped with paddle agitators and heated by steam jets. The starch and water are first made into a paste by being brought to the boiling point with live steam; the melted asphaltum is then introduced and thoroughly beaten into the paste by the agitators. This rapid stirring breaks. the hot asphaltum into minute particles which are distributed through the paste, producing a smooth chemical emulsion. This emulsion, when dried, is not soluble in water. The binder is mixed with the dry coal dust in a horizontal paddle mixer, 8 per cent. binder to the weight of coal being used. The resultant plastic mass is then discharged into the press, which is of the simple roll type. Since the binder is a liquid and is not sticky or gummy until

Jan 3, 1918

By A. F. Andresen

IN the course of another investigation the lattice parameters were determined for a series of compositions of tin in copper. Ten-gram samples of the alloys were made from spectroscopically pure tin and copper. The metals were weighed and placed in graphite capsules (previously fired at 5500°F) which were then sealed individually in evacuated vycor tubes. The tubes were mounted on a spit, transverse to its axis, which continually rotated the melts in a furnace. After homogenizing, filings were made of one third of each slug by filing off a complete cross section. A 325-mesh sieve was used to obtain the powder for the X-ray determination. The sieved powders were annealed in vacuo at 600°C for 24 hr to remove the cold work, and then quenched. The lattice parameters were determined with a flat-plate back-reflection camera using CuKa radiation (A., = 1.5405A, A,? = - 1.5443A). With this radiation the (331) and (420) reflections appeared close to the focusing region. As reference lines were used the same reflections from pure copper powder, between which the (420) lines of all these alloys are situated. The variation of the systematic error over this angular range was found to be less than the estimated experimental error ±0.0005A which is indicated in Fig. 1 for all but the sample with 8 pct Sn. As a check some of the powders also were examined in a regular Debye-Scherrer camera with the Straumanis film mounting. The parameters were here evaluated by extrapolation against cos2? to ?= 90o. The results are shown in Fig. 1 where the lattice parameters in Angstrom units are plotted as a function of weight percent of tin. The reflection lines for the 8 pct alloy were not clear at first, perhaps due to coring. Several measurements were made after different annealing programs on two separate

Jan 1, 1959

By G. W. Healy

G. W. Healy (union Carbide Metals 0.)-The author's paper is a useful contribution to the store of maps of chemical activities of oxides in multi-component slag systems. It is also a good example of the utility of the Gibbs-Schuhmann technique for calculating activities in a system where that of one of the components has been measured. This paper Koh and Caugherty. This plot is reproduced by alor in X-ray Metallography. Because of this nonlinearity, preparation cf suitable standards and/or correction for absorption and enhancement are essential in microanalysis. However, our objection is not the conclusion that Dr. Aaronson has arrived at nor the technique he has used; but only to the foot-note credited to V. Macres. The level of chromium that he was concerned with (less than 3 pet) is so low that the deviation of uncorrected Cr-curve will be negligible. Besides Dr. Aaronson has used chromium intensity from martensite and set it equal the bulk chromium content of the alloy. Using this chromium-intensity as a reference, he has calculated the amount of chromium in the ferrite. This amounts to the same as using an internal standard. Since the chromium content in austenite and ferrite are almost the same, enhancement due to iron in both will be the same and therefore does not need to be corrected. together with the author's recently published one1 on the CaO-FeO-Fe2O3 system will be most helpful to others learning to apply Schuhmann's method, which merits a far wider application than it has received to date and should greatly aid our understanding of equilibria between metal and oxide phases. As shown by okcen" its use may even be extended to sections of systems with any number of oxides. I have some questions as to the selection of equilibrium constants made by Dr. Turkdogan. He has chosen one for the formation of Fez03 from FeO and oxygen which gives Fea3 activities 50 pct higher

Jan 1, 1963

By J. W. Leonard

This expanded and more detailed supplement to earlier published work1 is offered as a means to demonstrate the high empirical correlation which exists between the readily measured coal bench scale test parameters of volatile matter (d & a.f.), Hard-grove grindability index (HGI), Koppers cone bulk density (BD) and pulverization level (% passing a 1/8-in. screen) to the less readily measured full scale coke stability index. Thus, Fig. 1, 2 and 3 represent the correlated test data contained in Tables I, II and III respectively. Ninety-six coals are correlated so that 97% of the resultant cokes fall within two points and 100% fall within three points of the actual tested coke stability indices. The main generalizations which can be drawn from the correlation of these coals are as follows: 1) The coke stability indices for higher bulk density coals (46.0 BD to 50.6 BD) appear to be largely influenced by differing combinations of factors for coals above and below a pivotal point of approximately 36% to 37% volatile matter. Below this pivotal volatile matter coke stability index appears to be influenced largely as a result of changes to the coal volatile matter and pulverization level. While above this pivotal volatile matter coke stability indices appear to be dependent on the coal hardness, as measured by the HGI, and to some extent upon coal volatile matter. Pulverization appears to have little influence on the coke stabilities of the harder coals (52 HGI to 58 HGI) of greater than 36% to 37% volatile matter. 2) The coke stability indices for lower bulk density coals (41 BD to 45.9 BD) appears to be largely influenced by changes to coal volatile matter and pulverization level for softer coals above approximately 58 HGI. 3) The main empirical observation to be drawn from these results is that for coals above approximately 36% to 37% volatile matter the quantities of hard and soft constituents as measured by the HGI are important when defining coal rank for correlation to the coke stability index.

Jan 1, 1965

By M. A. Rigdon, R. E. Grace

The dissociation of cupric oxide to cuprous oxide and oxygen was studied with a microbalmce technique at 700" to 750°C. In this temperature range the dissociation pressure of the reaction 2CuO= Cu2O + 1/2 O2 was: The theory of near-equilibriwm reaction rates predicts a linear relationship between reaction rate and the Gibbs free-energy change for small values of AF/RT. This correlation is found to be valid for AF/RT = -0.1 or approximately 200 cal per mole away from equilibrium. THE theory of reaction rates near equilibrium as developed from classical thermodynamics suggests a small range of linear behavior between the overall reaction rate and the free-energy change accompanying the process. The extent of this linear correlation is generally unknown, even to the order of magnitude. The idea of linearity is also found in the formal mathematics of coupled transport phenomena, e.g., chemical diffusion, thermal diffusion, thermoelectricity, and so forth. The linear array of forces and fluxes which leads to various main and cross coefficients is predicated upon linearity between reaction rates and the bulk thermodynamics which govern the process. The general case in reaction kinetics is well-known: the magnitude of the free-energy change does not cor- relate with observed reaction kinetics, irrespective of whether the process occurs by diffusion or chemical reaction or both. The real need is to investigate specific reaction paths near equilibrium in order to learn of the limitations in attempting to correlate reaction rates and thermodynamics. It is the main purpose of this paper to examine the dissociation kinetics of cupric oxide under conditions of known driving force where the dissociation process is likely to occur by chemical reaction. A secondary objective is to obtain equilibrium data for the CuO-Cu20-O2 system. In a prior paper Edmiston and race' investigated reduction kinetics of wustite in H2-H2O gas mixtures. The present study was carried out in oxygen according to the following reaction:

Jan 1, 1969

By C. D. Starr

IT is well known that the martensite reaction can be induced to occur isothermally above the M, temperature by plastic deformation of an alloy in its austenitic state, and also that as the test temperature is increased above the M. temperature, plastic deformation under a given set of conditions merely causes additional slip with a corresponding tendency toward the formation of less martensite per unit of strain. Thus it appears that a maximum temperature exists above which martensite cannot be formed isothermally by plastic deformation. This temperature is commonly designated as the equilibrium temperature Te. Attempts to determine experimentally the equilibrium temperature have indicated that a critical temperature is observed, under a given set of conditions, above which martensite cannot be formed isothermally by plastic deformation. But the observation of a "so called" critical temperature, Te, should not be confused with the equilibrium temperature, Te. In order to clarify this anomaly, true stress-strain curves were obtained for a series of type 304 stainless steel specimens (manufacturer's analysis, 0.08 pct C, 18 to 20 pct Cr, 8 to 10 pct Ni, balance Fe) over the temperature range 67" to 300°K.' Since martensite is magnetic, a quantitative measure of the amount of martensite that was produced by plastic deformation was obtained by determining the magnetic permeability as a function of strain. The results of these tests are given in Fig. 1. They appear to indicate that a plastic critical point does exist at about 240°K for the stainless steel under investigation here. But that 240 °K is not the equilibrium temperature nor even a true plastic critical temperature can be seen from Fig. 2 wherein the permeability of the same material is shown to increase with cold rolling at 293 OK. Consequently the observation of a "so called" plastic critical temperature is dependent on the mode of deformation and has no theoretical significance. Acknowledgment This work was sponsored by the Office of Naval Research. Permission to publish this note is gratefully acknowledged.

Jan 1, 1954

By James F. Kemp

Discussion of the paper of D. Foster Hewett, Bulletin To. 27, March, 1909, pp. 291 to 310. JAMES F. KEMP, New York, N. Y.:-Mr. Hewett's paper is one of exceptional interest, because it not only adds an important contribution regarding one of the rarer, valuable elements, but also because it introduces compounds hitherto unknown and in associations no less novel. While we have occasionally dis¬covered and recorded asphaltite in metalliferous deposits, for example in the Joplin and Granby districts, we have not seen a metallic ore in a deposit essentially asphaltite. The source and method of introduction afford a subject well worth serious reflection. Vanadium was first discovered and recognized as a distinct element in the slags obtained in smelting the titaniferous magnetites at Taberg, Sweden. For a long time, therefore, we looked upon the titaniferous magnetites as its hone. Analyses proved, years ago, that it was present in the ores of this type in New Jersey and in the Adirondacks. It was quite rarely determined, but when looked for it was, I think, invariably found, although the Amount seldom exceeded 0.5 per cent. of V,05., In just what combination it exists in the titaniferous ores is uncertain. One might imagine V2O3 replacing some of the Fe2O3 of magnetite; or, since in the lead series vanadates and phosphates are closely akin, one might wonder if a lime-vanadate could take the place of apatite. Yet no lime-vanadate has been found in nature, and apatite itself is usually rare in the titaniferous ores. When percentage-curves are plotted for a series of analyses of the ores, the line of vanadic oxide shows a curious sympathetic behavior with the line of chromic oxide;' but the data are somewhat limited, and no compound has sug¬gested itself which throws light on the matter. Dr. W. F. Hillebrand has discussed the occurrence and dis-

Oct 1, 1909

By Arthur C. Simmons

The Pennsylvania-grade oil industry suffered a serious decline in 1938, which can be largely accounted for by the decrease in the use of lubricating oil. Production was considerably lower than in previous years and prices were very much lower. Operating profits undoubtedly were lower than the year 1933, for the average price of Bradford crude in 1938 was $1.898 as compared with $1.86 in 1933, and the difference in average price of $0.04 per barrel was more than offset by increased operating costs and taxes. Bradford Field Production in the Bradford field in the state of Pennsylvania averaged 36,759 bbl. per day in 1938 as compared with 41,300 bbl. in 1937. The decline in average daily production of 4541 bbl. can be attributed to low market price and pipe-line proration rather than to the actual physical capacity of the field. Pipe-line proration was in effect for the last eight months of the year and the daily average production per month fluctuated between a maximum of 41,852 bbl. per day in March 1938 and a minimum of 33,649 bbl. per day in November. Production figures for Bradford field have been corrected to include only the parts of the Bradford field that arc within the state of Pennsylvania, but the well-completion data for the Bradford field cannot be segregated and include those of the entire Bradford field, part of which is in Sew York state. Production from the Bradford field was obtained almost wholly by water-flooding and no radically new methods or practices occurred. Intensive research work was carried on both by individuals and companies and as a cpooperative enterprise, and minor improvements are gradually occurring in spacing, shooting, application of pressure and water conditions. Drilling Central and Southen Pennsylvania.—Pennsylvania production in central and southern Pennsylvania was obtained largely by air and gas repressuring together with the usual amount of natural production, and the repressuring operations in other than the Bradford field have not

Jan 1, 1939

By J. B. Mackintosh

In a recent paper read before the Institute on this subject, Mr. G. C. Stone advances the theory that the precipitate obtained in Williams's volumetric process,* by treating the boiling nitric acid solution of a manganese salt with potassic chlorate., is not pure MnO2, but approximates more closely to the composition 10Mn02+Mn0. As the value of the process and the accuracy of our results mould depend on whether this was the fact or not, it has seemed to me, and to my associates, Messrs. Beebe and Colly, that it would be of importance to ascertain the composition of this precipitate, and to that end the following series of experiments has been undertaken. These experiments have all been based on the considerations: 1. That potassic permanganate has an oxidizing power equivalent to five atoms of oxygen for every two of manganese : K2Mn2O8 = K2O.2MnO.O5. 2. That the same amount of manganese in the state of binoxide has an oxidizing power equivalent to two atoms of oxygen : 2MnO2 = 2MnO.O2. If, then, we take a solution of permanganate of unknown strength, and reduce it to binoxide, the oxidizing power of the binoxide formed will be equal to that of two-fifths the quantity of the permanganate solution originally taken. While, if the precipitate obtained should not be binoxide, but an indefinite or definite mixture of bin- and mon- oxides, then, from its equivalent oxidizing power, we can calculate its composition. The analyses were conducted in the following manner. The amount of permanganate taken was decomposed with hydrochloric acid, and concentrated to expel the excess of water. Sufficient excess of nitric acid was now added, and the solution was boiled until all the hydrochloric acid was destroyed. The manganese was then precipitated by potassic chlorate; and, after standing some time to cool—a pre-

Jan 1, 1884

By Paul Merica

ONE of the most useful, and at the same time least commonly used, methods of thermal analysis for the determination of transformations in metals and alloys consists in the recording of the tune intervals required for successive increments of temperature change during heating or cooling, the temperature of the furnace containing the specimen being altered at a uniform rate. The curve obtained by plotting these time intervals as a function of the mean temperature of the specimen during the interval is called the inverse-rate curve. It is probably due to the fact that no simple and convenient method has apparently been available for the measurement of the successive time intervals that this method has not been so generally used as, for example, the differential method, for which several tykes of automatic or semi-automatic apparatus have been designed. Whenever this method has been used, the intervals have usually been measured with the use of a chronograph; its operation as practised at the Bureau of Standards' is as follows: The temperature of the specimen is measured by a thermocouple and a dial potentiometer. The operator sets the potentiometer at successive values of the electromotive force differing by equal increments, usually 0.02 millivolt, and records the exact instant on the chronograph, by pressing a contact key, at which the galvanometer coil passes through its null position. Two-second intervals are also recorded on the chronograph record, and the number of 'seconds elapsing between successive signals is afterward counted from the record and plotted as a function of the electromotive force or of the temperature. This is an admirable method and by it most minute thermal arrests may be detected, but it requires a good chronograph, which is generally difficult to obtain, and the time of one operator during the recording and, subsequently, to read the intervals from the record; the latter operation often takes from one to two hours.

Jan 7, 1919

By Arthur C. Simmons

The Pennsylvania-grade oil industry suffered a serious decline in 1938, which can be largely accounted for by the decrease in the use of lubricating oil. Production was considerably lower than in previous years and prices were very much lower. Operating profits undoubtedly were lower than the year 1933, for the average price of Bradford crude in 1938 was $1.898 as compared with $1.86 in 1933, and the difference in average price of $0.04 per barrel was more than offset by increased operating costs and taxes. Bradford Field Production in the Bradford field in the state of Pennsylvania averaged 36,759 bbl. per day in 1938 as compared with 41,300 bbl. in 1937. The decline in average daily production of 4541 bbl. can be attributed to low market price and pipe-line proration rather than to the actual physical capacity of the field. Pipe-line proration was in effect for the last eight months of the year and the daily average production per month fluctuated between a maximum of 41,852 bbl. per day in March 1938 and a minimum of 33,649 bbl. per day in November. Production figures for Bradford field have been corrected to include only the parts of the Bradford field that arc within the state of Pennsylvania, but the well-completion data for the Bradford field cannot be segregated and include those of the entire Bradford field, part of which is in Sew York state. Production from the Bradford field was obtained almost wholly by water-flooding and no radically new methods or practices occurred. Intensive research work was carried on both by individuals and companies and as a cpooperative enterprise, and minor improvements are gradually occurring in spacing, shooting, application of pressure and water conditions. Drilling Central and Southen Pennsylvania.—Pennsylvania production in central and southern Pennsylvania was obtained largely by air and gas repressuring together with the usual amount of natural production, and the repressuring operations in other than the Bradford field have not

Jan 1, 1939

By Ian J. Smalley

"Quickclay is an extreme case, it is by far the most mobile of all the common solid materials on the earth's surface. It has both a high water content and a mineral texture that allows it to flow with the utmost ease. A mass of quickclay that has lain undisturbed for thousands of years can be jarred into motion by any sudden shock." The quotation is from the paper by Kerr called, "Quickclay," which was published in Scientific American in 1963. This was probably the most widely read paper on quickclay ever published. It was reprinted by Fred Betz in his Benchmark collection on Environmental Geology (BM 25), A quickclay is an extremely sensitive soil. The sensitivity parameter is produced by dividing the undisturbed shear strength by the remoulded shear strength. If a value greater than 50 is obtained, then the soil can be classified as a quickclay. True quickclays are characterized by a very low remoulded strength of the order of 0.5 kPa. The classic quickclays are found in Scandinavia and Eastern Canada, but the 1964 Alaska earthquake revealed a considerable quick¬clay deposit underlying the town of Anchorage. This was discussed in a classic paper by Kerr and Drew in Engineering Geology in 1967. The Kerr views on quickclays were perhaps most clearly expressed in the paper with Liebling in Geol. Soc. Amer. Bull. in 1965. They suggested that the major critical conditions which contribute to quickclay movement are: substantial quantities of layer lattice silicates of colloidal size (about 40% or more by dry weight), sub¬stantial pore water (44%), a reduction in electrolyte concentration below 5 g/l of salt, and addition of a dispersant. There is still discussion and disagreement about the nature of quickclays and the mechanisms of quickclay slides; the "clay mineral"-based views favored by Kerr still find support, although an alternative "primary mineral" view suggests that it is the finely ground primary minerals

Jan 1, 1985

Hugh M. ROBERTS,* Minneapolis, Minn. (written discussion ? ).¬The paper by Messrs. Hall and Row marks a distinct advance in the art of diamond drilling, because it records a systematic-application of a method for directing the path of the diamond bit. Their work is an admirable example of engineering development. They had a definite object to attain; i.e., the drilling of many vertical diamond-drill holes to depths of 2500 or 3000 ft. (762 or 914 m.). They availed them-selves of a method of wedging seldom used, improved the manner of making the wedges, developed a technique of survey, and put the process into practical, continuous operation. So effectively has this been done that they determine the average cost of the work. The publication of the results, in the form of detailed diagrams, makes the application general to whoever has a similar problem. The wedging of diamond-drill holes has been practised in the Lake Superior region for the purpose of making branch holes, particularly where the original hole has penetrated a great thickness of glacial drift. The uneven nature of the iron formations has caused the results to be somewhat uncertain. One operation, in 1907, near the American mine on the Marquette Range, by the firm of Longyear & Hodge, predecessors of the E. J. Longyear Co., resulted in the drilling of a hole 1828 ft. (557 m.) deep, with two branches at depths 100 ft. (30 m.) and 770 ft; (234 m.), respectively. A second hole from the same set-up went to a depth of 2497 ft. (761 in.) with a branch at 185.0 ft. (563 m.). In this instance, the wedges were forged to the desired shapes and angles with respect to each other. A drill hole, sunk in 1915,. in the township of Bates in the. Iron River district of Northern Michigan, which penetrated 385 ft.

Jan 11, 1919

By J. L. Gissy, G. H. Schippereit, J. B. Schroder

THE existence of mechanical anisotropy in hexagonal metals is well known.' One possible method of measuring the degree of anisotropy in a metal is to make hardness measurements on the different planes of a single crystal. So far as is known, no single-crystal hardness data have been reported in the literature for alpha titanium. To obtain an estimate of the variation in hardness with crystallographic direction in titanium, Knoop hardness measurements were made on single crystals of electrorefined alpha titanium obtained from the Bureau of Mines, Boulder City, Nev. The hardness of arc-melted ingots prepared from this material was 64 Bhn (1000-kg load, 30 sec). Crystals of sufficient size were mounted in epoxy resin with the basal plane exposed. They were then polished and etched to remove excess plastic resin and work-hardened surface material. The crystals were then examined by x-ray diffraction, using the back-reflection Laue technique to insure that the crystals were properly oriented and strain free. After Knoop hardness readings (100 or 200-g load) were taken on the exposed surface, the crystals were remounted to expose a prismatic face and the foregoing procedure was repeated. Hardness values for various orientations are listed in Table I. The data show a difference between the hardness of the basal planes and that of the prismatic planes, as anticipated. More striking is the hardness difference observed between different orientations of the indentor on the prismatic planes as shown in Table I and Fig. 1. All of the indentations shown in Fig. 1 were made with a 100-g load. The long axis of indentation A is parallel to the unique (c) axis of the crystal. The deformation marks visible around indentations A and C of Fig. 1 are probably slip traces of the (10.0) system reported by Rosi, et al. The greater hardness observed when the long axis of the indentor was perpendicular to the unique axis of the crystal (indention B) is probably caused by the opera-

Jan 1, 1959

By S. R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

John Dasher (Materials and Processes Engineer, Crucible Steel Co. of America, Pittsburgh, Pa.) The authors are to be congratulated for their excellent work, dramatic results, and persuasive explanation on the neglected subject of the temperature variable in soap flotation. The explanation includes why heat is helpful in conditioning and why heat is helpful in flotation. This is a fine start, but I hope the work will be continued to show which is the major effect. In the work of Noman and Dash er(1) it was found that substantially all the benefit of heat came from the conditioning step, and that results were much better if a thick pulp was conditioned hot and then diluted with unheated (or less heated) water for flotation (or agglomerate tabling) than if the same quantity of heat was used to condition and float at some intermediate temperature. In other words, heat for conditioning gives a Rood return, but additional heat for dilution water is near or beyond the point of diminishing return. Strathmore R. B. Cooke, lwao lawsaki, and Hyung Su0p Choi (Authors' Reply) Mr. Dasher'skind comments on our paper are appreciated. In view of the relative simplicity of empirical investigationsof the temperature variable upon conditioning and flotation, it ispuzzling why the subject is so neglected. Our work, being sub sidiary to the main investigation of the effect of structure of fatty acid collectorsupon iron ore flotation, was quite restricted, but we intend to return to the subject as soon as possible. Mr. Dasher's point, that given a certain number of calories it is better to invest them for conditioning in a thick pulp rather than to spread them out for both conditioning and flotation operations, is well taken and cannot be argued. On the other hand there is no question that high temperature during the flotation of iron ores induces superior frothing characteristics, and, in particular, greatly augments the rate of flotation and markedly decreases the time required for "difficult" particles to float.

Jan 1, 1961

By Magnus Troilius

For some time I have been using with great advantage, for the purpose of determining rapidly and accurately the chemical composition of gases from Siemens producers, an apparatus arranged generally like that proposed by Prof. Eggertz; * and I now take pleasure in laying before the members of the Institute a description of the apparatus and its use, hoping that some of them may find it. of practical advantage. At the end of the paper are given some results obtained and heat calculations, with the necessary data for the same. COLLECTION OF GASES. Fig. 1. Shows the arrangement for taking a sample of gas. The funnel F, which may be made of tin plate, is made to fit the test-hole. The gas passes up through the funnel and through the rubber-tubing with the glass tube K, filled with asbestos for retaining dust,, and is drawn into the upper flask by means of water flowing from the same into the lower flask. The upper flask must be completely filled with water from the beginning, so that no air remains. When filled with gas the screw-compressors are securely fastened on, and the flask disconnected from the funnel and receiver. Quart flasks, with openings at the bottom, are very suitable, and easily obtainable. COMPOSITION OF THE GASES. The ingredients found in producer gases are: carbonic acid (CO2), oxygen (0)) ethylene (C2H4), carbonic oxide (CO), hydrogen (H), and marsh gas (CH4). The nitrogen is taken by difference. CO2,O,C2H4, and CO are determined by absorption in various liquids and by observing the resulting diminution of volume. H and CH4 are determined by combustion with oxygen. Carbonic acid.—For this gas is used a solution of 16 grams of potassium hydrate in 100 C.C. of water. 4 or 5 C.C. of this solution absorb 100 C.C. of CO2.

Jan 1, 1883