Search Documents

By E. S. Machlin, A. J. McEvily

HE results of an experimental investigation by McEvily and Machlin have indicated that a strong relationship exists between the processes of cross slip and fatigue. Whenever dislocations can cross onto an intersecting plane and expand thereon, as in AgCl crystals, the usual type of S-N behavior is obtained, but when such a process is difficult, as in NaCl crystals, fatigue does not occur in its usual manner, if at all. MgO, because of its crystal structure (NaCl type) and slip systems ({110}<110>) would not be expected to fail in fatigue. However, Cornet and Gorum2 have found something akin to the usual type of fatigue behavior for MgO crystals. The purpose of this note is to attempt to resolve this apparent discrepancy. In Cornet and Gorum&apos;s work as-cleaved crystals were tested under cyclic axial loading, whereas in McEvily and Machlin&apos;s work chemically-polished crystals were tested in reversed bending. Because of the difference in specimen preparation, the major effort of the present work was directed toward comparing the behavior of as-cleaved as opposed to chemically-polished specimens. The effect of type of loading seemed less important, but a check was made on this also. Eighteen bend tests and one axial load test were made. The specimens were cleaved from Norton magnorite blocks, and measured 1 by 3/16 by 1/8 in. To avoid failures in the grips, the thickness of the bend specimens was reduced from 1/8 in. near the ends to 0.04 in. in the central portion. This reduction was from one side of the crystal only. Twelve specimens were polished in orthophosphoric acid to remove the damage due to cleavage. The other six specimens were not chemically polished so as to maintain the as-cleaved condition of the crystal faces which had not been reduced. The axial-load specimen was reduced from both faces to a thickness of

Jan 1, 1962

By Joseph W. Richards

THIS method of briquetting flue-dust, or flue-dust mixed with fine ores, or, in a few exceptional cases, coke-dust, has come into large commercial use in Europe, and a small plant is already in operation in the United States. It promises to become of such great importance to the iron industry of the United States that the following description will certainly interest the majority of our pig-iron producers. Discovered in 1908, the process rests upon the observation of Dr. Schumacher that blast-furnace flue-dust, while possessing of itself no binding or cementing properties, acquires strong cementing properties if mixed with a very small amount of certain salt solutions, the amount of which is so small that the resulting cementation appears to be rather by catalytic action of the salts added than by the mass-action of such chemicals. To be more specific, fresh blast-furnace flue-dust mixed with from 5 to 10 per cent. of its weight of magnesium chloride or calcium chloride solution-that is to say, with from 0.25 to 2 per cent. of its weight of magnesium chloride or calcium chloride-acquires the property of setting within a short time, from 15 to 60 min., and forming a hard cemented briquette. Alkaline solutions appear to have no action such as described, and they even interfere, if present, with the action of the magnesium and calcium solutions. When treated in this way the flue-dust briquette sets very hard, apparently from pure excess of cementing- and setting-power. It is, therefore, possible to . mix with the flue-dust a considerable proportion of inert ore or like material, which has no setting-power by this process, and thus to make a compound briquette containing large quantities of ore mixed with flue-dust, but in which the flue-dust may be regarded as the cement or binding-material. A particularly strongly cementing flue-

May 1, 1912

By Robert R. Brookshire

Brush plating has been thought of by many as black magic bordering on alchemy. Actually it is a science that uses both electro-chemical and mechanical engineering skills and technology. We are not sure when brush plating was first used or by whom. I do know that many times when we would put in for patents on things we thought of as new and innovative, we would find that someone had done it many years before. It took World War I1 to get brush plating off and running. Now at this point, someone may be asking just what is brush plating? And why are we plating brushes? One way of describing what brush plating is, is by telling what it is not such as tankless plating. Brush plating-is an electro deposition of an electro-platable element or alloy onto a conductive surface. To do this a source of direct current is required; this can vary widely. I prefer stepless voltage control from 0-35 volts with a capacity depending on the size job to be done. This can vary up to 500 amps for normal applications. In one case we have used 7500 amps.. In the beginning a brush was actually used with a wire in the middle of the bristles and a jelly-like paste made up from tank plating solutions. The bristles were saturated with the gunk and the spot to be plated was muddled with the concoction at a potential which was the same as the applied tank Voltage. Metal was deposited but only thin coats were achieved. Today we use graphite wrapped or covered with cotton to form a Q-tip type anode. By using graphite rather than a specific metal we are able to either plate, de-plate or strip, electro- mill, electropolish, or anodize--all with the same equipment. Only the electrolyte needs to be changed.

Jan 1, 1984

By T. Kilner, A. Plumtree

DURING an investigation of electro-deposited silver structures, samples were prepared for metallographic examination by cold mounting in plastic, grinding on successive grades of emery paper down to 3/0, and chemically polishing by swabbing using the chromic acid solution described by Gilpin and Worzala.1 Attempts to etch these samples using the standard solutions described for silver (e.g., 5 pet KCN-5 pet Na2S2O8, H2O2-NH4OH, and various potassium dichro-mate solutions) all failed to give good results due to staining of the samples and to rapid etching. The staining was caused by the chromic acid polishing solution being trapped in small fissures between the sample and the mounting plastic, and also in small fissures in the sample itself. To overcome these difficulties, an etchant was developed which prevented staining at the same time as it slowly etched the sample. This resulted in a very clean, crisply etched surface as shown in Figs. 1 and 2. This etch consisted of 10 ml of orthophosphoric acid, 10 ml of distilled water, and 2 drops of the polishing solution noted above,&apos; which is made by mixing 100 ml of saturated CrO3 solution, 45 ml of 10 pet HC1 solution, and 800 ml of distilled water. The etching procedure involved taking the final polished sample, either immersing or swabbing in the etchant for a period of 1 to 2 min, rinsing as quickly as possible in distilled water, alcohol, and ethyl ether in that order, and then immediately drying. This etch is easily controlled due to its slow rate of etching, and produces samples with clean, sharp surfaces. Pits due to overetching produced varying contrast effects when viewed under polarized light, and are therefore obviously useful for revealing many structural details within the sample. Another effect of overetching was to produce a height varia-

Jan 1, 1968

By Bert S. Sandell

Much has been said and written about the various uses of die castings, their applications in the various industries and their advantages and disadvantages. Examination of this literature, however, fails to disclose any data concerning the effect of temperature upon any of the physical properties of die-casting alloys. The uses and applications of die castings are so numerous, and of such a varied nature, that far too lengthy a manuscript would be required to list all of them. Brief mention of some specific cases will suffice to illustrate the temperature ranges in which certain die castings function. Automobile hardware, such as hub caps, door handles, radiator caps, etc., can be used as one example. Castings of this type are constantly exposed to varying climatic conditions, temperatures ranging from below zero to upwards of 100" F. Refrigerator parts, such as ice-cube trays, etc., form another example. Approaching the other temperature extreme, we encounter conditions such as are found in kitchens in which oven-heat indicator parts, cooking utensils, waffle grids, etc., embody use of die castings, where temperatures as high as 500" F. are often met with. Because of this variation in service temperatures, it was felt necessary to ascertain the effect of these temperatures upon the physical properties of die-casting alloys. The Charpy impact test was chosen first because of its simplicity, and because of the fact that brittleness is more likely to be objectionable in die castings than hardness or other physical properties. Alloys Investigated Two types of alloys were used in this investigation—zinc-base and aluminum-base alloys. Two alloys of each group were included. Those most generally employed in the industry at present were selected. Alloys A and B are of the same nominal composition, and correspond to A. S. T. M. alloy XXI, containing 4 per cent aluminum, 3 per cent copper, 0.1 per cent magnesium, and the balance zinc of 99.99 per cent

Jan 1, 1932

By Haakon Styri

IN discussion of Dr. Fitterer&apos;s paper on electrolytic separation of slag inclusions, some results from experiments on electrolyzing high-carbon steels at the SKF Research Laboratory were given.1 We had been working for a number of years on chemical methods of separating the inclusions but could not find any solvent that would dissolve the steel without attacking some of the inclusions, particularly the sulfides in which we were mostly interested at the time, nor any that would dissolve all sulfide or silica in filings as fine as 300 mesh without attacking the iron. Electrolytic methods had also been tried without any real progress until we learned from the Bureau of Mines about the use of the collodion membrane around the anode. Our early difficulties were to some extent different from those of the Bureau of Mines, perhaps because of experimenting on steels of higher carbon content, but most of our difficulties were of the same nature as those of the Bureau. Formation of large quantities of basic hydroxides use of impure and oxidized ferrous sulfate. To protect from oxidation from the atmosphere during electrolysis, after purer chemicals were obtained, a thin layer, 1/8 in. or less, of molten paraffin was poured over the surface of the cathode liquid, where it solidified. It was found desirable also to hold the cathode chamber slightly acid by initial addition of 0.1 per cent acid (sulfuric or hydrochloric) to prevent precipitation of the hydroxide. This acidity would decrease gradually and the cathode chamber would become neutral before the end of the electrolyzing. The increase in acidity in the anode chamber during our early experiments had appeared to cause attack of the precipitated sulfides in the residue, which originally was analyzed by volumetric method for sulfur, and for this reason a 10 per cent sodium citrate solution was substituted for the sulfate in the anode chamber.

Jan 1, 1932

By Robert H. Richards

The group of four papers on ore dreseing read at the Butte meeting, all of them dealing with the recent developments at the Great Falls and Washoe plants of the Anaconda Company, form an extremely important contribution to the subject of ore dressing. It proves the efficacy of the new hindered-settling principles first brought out in a paper entitled Close Sizing Before digging&apos; and later elaborated in a paper entitled Development of Hindered-Settling Apparatus: and it is the first large demonstration on this class of mill that has been made. It must be very gratifying to all mill men to have these papers at hand, charged with careful investigations and results pointing to the conclusions reached; the papers cannot fail to be a great help to every designer of mills and to mill men who are working on this class of concentration. The papers have dealt with their subjects so completely and have demonstrated every point from beginning to end in each case so thoroughly it leaves little for the commentator to say in the way of criticism. Therefore it seems best to him to confine himself to adding a few points of history which he believes will be interesting to the readers. Referring to the paper by Mr. Wiggin, and to the fact that the Richards hindered-settling pulsator classifier was turned down, the writer wishes to say that this classifier was the first of its kind that had ever been introduced, and since that time it has undergone great developments which he believes would overcome the difficulties encountered in the test,. In fact, there was one test made at Great Falls which with the Wilfley tables and vanners brought all the tailings down to 0.36 per cent. copper except the fine slime. Since that time, and since the classifier has been further developed, in one Colorado mill it proved a wonderful amalgam catcher, catching in all

Jan 1, 1914

By Minoru Sasabe, Mayurni Sorneno, Kazuhiro Goto

I) The Object of the Present Experiment. When the oxygen chemical potential in the gas phase is changed, the oxygen chemical potential in the liquid metal or in the liquid oxide phase will be subsequently changed. The object of the present experiment is to develop a method of measuring the change in the chemical potential of oxygen in liquid metals and in liquid oxides with respect to time, when the oxygen potential in the gas phase changes. II) The Experimental Method. The following types of the oxygen concentration cells with the solid electrolyte of Zr0z-CaO are used: KAZUHIRO GOTO, MemberAIME.MINORU SASABE,and MAYUMl SOMENO are Associate Professor, Research Associate, and Professor, respectively, Department of Metallurgical Engineering, Tokyo Institute of Technology, Meguro-ku, Tokyo, Japan. Manuscript submitted March 12, 1968, EMD. Igas phase liquid Ag or Pb ZrO2-CaO electrolyte!, The measured reversible electromotive force can be expressed by the next equation, provided that the transference number of the oxygen anion in the electrolyte is unity: E = RT/nF log (at electrode I)/P~ (at electrode 11) where is the electromotive force, R is the gas constant, T is absolute temperature, n is valence of oxygen anion, and Pq is the oxygen pressure at the electrodes. As shown in the previous work1 of the authors, the electromotive force is determined by the difference in the chemical potential of oxygen at the vicinity of the interfaces between the solid electrolyte and the electronic conductors used for the two electrodes. Fig. 1 shows the two kinds of the cell assembly used to measure the change of the chemical potential of oxygen in liquid metals and liquid oxides with respect to time. In both cases, the change of the oxygen pressure in the gas phase is measured by the independent oxygen concentration cell located above the

Jan 1, 1969

By A. B. Kinzel

MUCH work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. . This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it con-stitutes the main action in the usual steelmaking processes. A. L. Feild1 has formulated a basic differential equation expressing the open-hearth reactions and Hefty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action. to the reaction FeO +C ?? CO +Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed&apos; constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Feild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X 10-2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty&apos;s, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By O. J. Malacarne, D. G. Millenbruch

The use of a series of thickeners for washing of the slime fraction of a leached ore is not uncommon in the uranium industry; however, few ore processing mills have used a thickener circuit for washing leached total ore. The common practice is to wash the sand fraction in classifiers and the slime fraction only in thickeners. At the Uravan mill of Union Carbide Nuclear Co., a total ore acid leach is employed to extract uranium values from sandstone ores. These leached ores are then washed at a nominal rate of from 1000 to 1300 tpd in a series of washing thickeners. A typical screen analysis of the ore being washed in these thickeners is: 25 pct, -200 mesh; 3 pct, +35 mesh; and about 1 pct, +14 mesh. The amount of slimes (-200 mesh) will vary from 20 to 30 pct as the mill receives ore from 150 different mines. The washing liquor is acidic, from a pH of about 2 in the first thickener to 0.6 pH in the last thickener and, of course, all acid duty equipment must be used. The Uravan mill of Union Carbide Nuclear Co. is located in Montrose County, Colo. and is physically located on a canyon wall along the San Miguel River. The thickeners referred to in this paper are located on top of the mesa above the canyon. For purposes of identification, these thickeners are numbered 1 through 8 from south to north. GENERAL DESCRIPTION OF CIRCUIT The circuit utilized consists of eight wooden fir tanks, 60-ft diam by 12-ft deep, set in a line and staggered in elevation by approximately 3 ft. The washing water flows through the thickeners by gravity, while the ore pulp is pumped uphill from thickener to thickener. Adequate piping and pumping capacity are available so that any of the thickeners can be bypassed in the circuit. All the controls for the

Jan 1, 1962

By G. C. Stone

At the conclusion of my paper on the same subject read at the Boston meeting of the Institute, I offered to send some of sample No. 2 to any chemist who wished to analyze it. Eight chemists wrote to me for samples; so far I have received results from five. I give these results in a table (on the following page), together with the results previously obtained: As to the chemists and their methods : K is an iron-works chemist whom I only know by correspondence; lie writes: "No. 27(13.64) was obtained by the method I generally use, as follows : Dissolve 0.8 grams spiegel in hydrochloric acid and a little potassium chlorate, in a half-liter flask. Boil off most of the acid, add ammonia in slight excess, redissolve in acetic acid, using rather more than is really necessary, and then add 8 or 10 grams of sodium acetate and make up to the mark with warm water. Boil hard for fifteen minutes, then allow to settle (cool?), until the liquid reaches the mark, and withdraw 300 C.C. of the nearly clear liquid. Add to this an excess of hydrochloric acid, evaporate to dryness, take up with hydrochloric acid and water, and separate the iron by two precipitations with ammonia (I have often tested the ferric hydrate for manganese, but have never found any, if the separation by ammonia was properly made). Finally, precipitate the manganese as phosphate." Nos. 28, 29 (13.35, 13.07) were by Ford&apos;s method." No. 30 (13.50) was by Troilus&apos;s method He writes, " I may add the results are quite as good as I expected, although for any element except manganese, they are not close enough for anything like accurate work." L is a firm of commercial chemists of large experience who have made a specialty of iron work. Their method is as follows : Dissolve

Jan 1, 1884

By R. W. Smith. Discussion by D. Watson, R. M. Manser

D. Wotson, R. M. Monser (Watten Spring Laboratory, Stevenage, Herts., U. K.) - This is a valuable and interesting paper and will make an important contribution to the development of a general theory of silicate flotation. In particular the dominance of surface reactions which produce fluosilicic acid and its ions has been convincingly demonstrated. In a paper to be published shortly, however, we offer some evidence which is not consistent with the feldspar activation theory proposed by Prof. Smith. This theory, given in Eqs. 17-20, suggests that activation takes place through the exchange of SiF6 ions for OH- at aluminum sites. This results in a negatively charged site facilitating adsorption of RNH3 Firstly, we have determined the flotation response (using the vacuum flotation technique) and the adsorption of dodecylamine on a natural feldspar (albite) and on the same feldspar after washing with perchloric acid at pH3. This pre-treatment was shown to remove surface adjacent aluminum atoms. It was found that although the acid washed feldspar floated much less easily than the untreated sample, the function of fluoride ion - giving activation over the pH range 4-6.5-was preserved. Moreover, the amount of dodecylamine adsorbed either with or without fluoride present is little affected by acid-washing, despite the depression caused by this treatment. This suggests that surface aluminum atoms can be of little importance in the fluoride activation mechanism. Secondly, we have determined the changes in solution concentration of F- and H+ (or OH-) accompanying reaction of the surface with fluoride ion. The ratio of H+ lost from solution to F- lost is high, ranging from 6.9 at pH4 to 1.0 at pH 7.5. This is consistent with reaction of HF (6 molecules for every Si removed) at the surface, producing SiFi-ions, but not with the re-adsorption of these ions.

Jan 1, 1967

By M. J. Marcinkowski, R. M. Fisher

The flow stress-grain size relationship has been determined at room temperature in both a disordered and a fully ordered FeCo for plastic strains up to 30 pct. The results are in agreement with a Hall-Petch relation of the type given by Of =a,+kd-1/2 where of is the flour stress and a, increases mono-tonically with increasing strain to a maximum value which is much higher for the ordered than for the disordered alloy. The slope, k, is found to increase FOLLOWING the original work of Halll and petch relating the effect of grain size to the lower yield stress of iron and steel, it has been generally found that the yield stress oy.s. of polycrystalline metals with strain to a maximum and then decrease for both ordered and disordered alloys. However, k for the ordered alloy is in general higher than that for the disordered alloy and the critical strain for k max somewhat larger. All of these observations can be satisfactorily accounted for quantitatively and in some cases semiquantitatively by using a slip band-grain boundary intersection model, and by taking note of the fact that, in general, moss slip, while quite common in the disordered alloy, is extremely difficult in the ordered alloy. obeys a relation of the form oy.s.=a0+kd-1/2 [1] where a, and k are constants and d is the mean grain diameter. For convenience, and in accord with prevailing custom, Eq. [I] will be referred to simply as the Petch relation. Tjerkstra3 and Armstrong, Codd, Douthwaite, and petch4 showed that the flow stress af of iron or steel measured at strains of up to at least 20 pct also obeyed a relationship of the type given by Eq. (11. The latter investigators have also shown that Eq. [I] applies to fcc and hcp metals and alloys.

Jan 1, 1965

By Wolfgang Gartner

METALLURGISTS engaged in the pulling of single crystals of germanium and silicon, and their zone purification and zone levelling for transistor and diode production, have found that the lifetimes of minority carriers in low resistivity samples tend to be shorter than in high resistivity material, although equal care is taken in the crystal preparation. In other words, it is more difficult to obtain long lifetimes in single crystals of low resistivity semiconductors. It is the purpose of this note to point out that this phenomenon follows directly from the Hall1 and Shockley-Read&apos; theories of lifetimes in semiconductors." In general, the recombination mechanism may be very complicated,&apos; but experiments seem to indicate that the simple formula2 for the lifetime of excess carriers given by n0 + n3 Pn + P1 T = Tpo,------------------+ Tjpu ----------------------- [ 1 ] nu + pn na+ + Pa is a good representation of the situation prevailing in transistor grade semiconductors. In this formula, no and pa are the equilibrium densities of electrons 6+ - E./ET and holes, n1 = N,e is the number of electrons E1- E2/KT in the conduction band, and p1 - N,e is the number of holes in the valence band, both for the case in which the Fermi level falls at the trap level, E1. N,. is the effective density of states in the conduction band; E1, the recombination level; E1, the lower edge of the conduction band; k, Boltzmann&apos;s constant; T, absolute temperature; N,., effective density of states in the valence band; and E,., the upper edge of the valence band. t,.,, denotes the lifetime of holes injected into highly n-type material, and The indicates the lifetime of electrons injected into highly p-type material. Eq. 1 holds for nondegenerate semiconductors in which only one recombination level is active and the charge in the recombination centers is neglected. It is further assumed that the number of injected ex-

Jan 1, 1957

By R. E. Reed-Hill, J. L. Martin

Kinking is an important deformation phenomenon in poly crystalline a zirconium. The crjlstallo-gvaphic features of the most important form of kinking have been determined with the aid of twins formed at 77°K in grains previously kinked at high temperatures. It has been .found that the kink-band boundaries correspond to walls of edge dislocations with (1150) Burgers vectors and dislocation lines parallel to (1070). The present observations imply that basal slip is an important secondary-slip mode in polycrystalline zirconium. Previous single-crystal studies13 did not veveal this mode Other evidelzc.e for (0002)(1120) slip is also presented. ThE first studies of kinking in hexagonal metals were made by orowan,1 using single-crystal cadmium wires. He suggested that this was a new de- formation mode in metals, different from ordinary glide or twinning. Next, Hess and Barrett2 studied zinc-crystal rods in compression, and were able to offer an explanation of the phenomenon described by Orowan. They concluded that kinks required no new deformation mechanism and were a special form of deformation band that developed gradually and solely from basal glide. Similar kink bands were then observed by Washburn and parker3 on zinc crystals deformed in tension at low stresses and high temperatures. In titaniun,4 kink bands associated with {1010}<1120> prism slip have been observed in coarse-grained specimens. Magnesium5 and rhenium6 have also been observed to kink in conjunction with their basal- and {1010} prism-slip systems, respectively. Yttrium has (1010) as a predominant slip plane, but no observations of kink bands were reported.7 Since no previous investigations of kink bands in zirconium have apparently been made, this study was proposed. Its aim was to determine the crys-tallographic features of a type of kink band frequently observed in polycrystalline zirconium. EXPERIMENTAL APPARATUS All tests were performed on a type TTC Instron machine. The cross-head speed usually chosen in tension or compression was 0.02 in. per min. Ten-

Jan 1, 1964

By F. L. Vogel

Densities and distributions of dislocations in plastically bent germanium crystals before and after annealing were studied. In the bent and annealed crystals, the theoretical relationship between radius of curvature and density of dislocations is confirmed. Before annealing, however, more dislocations are present than required, and these are distributed with a minimum at the neutral axis and maxima at the top and bottom surfaces. On annealing, three significant changes occur in the bent bars: 1) the average dislocation density is reduced, presumably by the annihilation of opposite signs; 2) dislocations migrate from the high density outside regions toward the low density neutral axis, thus producing the equilibrium distribution of dislocations; and 3) a polygonized structure is formed by movement of the dislocations into walls normal to the slip plane. ETCHING to reveal edge dislocations&apos;-" offers a unique opportunity to study, in germanium single crystals, the functioning of dislocations in plastic deformation. Plastic bending is ideally suited to this purpose because it produces a static array of edge dislocations in an ideally plastic material which is predictable from the theory." " Nye" has given a rather complete treatment of the geometry of bent crystals in terms of dislocations. The density of excess dislocations is related to the radius of curvature of the slip plane of a bent crystal, as shown in Fig. 1, assuming the absence of macroscopic elastic stresses. The curvature of any plane in the zone of the bend axis is found by resolving the Burgers vector into that plane, so that for the usual case where the slip plane is inclined at some angle 0 to the neutral plane of the bar, the equation applies, with T equal to the radius of curvature of the neutral plane of the bent crystal. Two predictions which are relevant to this study may be made from Eq. 1. First, in crystals bent to various radii, the average excess dislocation density is inversely proportional to the radius and second, for a bar bent to a radius which is large compared with its thick-

Jan 1, 1957

By R. Kossowsky, W. C. Johnston

CONSIDERABLE experimental data has been published in recent years on a few directionally solidified aluminum base eutectic alloys. The mechanical properties of A1-Al3Ni eutectic have been studied by Lemkey, Hertzberg, and Ford1&apos;,2 and Salkind et a1.3 where the alloy has been demonstrated to behave as a whisker reinforced composite with superior properties over many aluminum alloys. It has also been shown4 that aluminum reinforced with Al3Ni whiskers R. KOSSOWSKY, Member AIME, is Senior Metallurgist, Westing-house Research Laboratories, Pittsburgh, Pa. W. C. JOHNSTON, formerly with Westinghouse Research Laboratories, is Head, Department of Physics, George Mason College, University of Virginia, Fairfax, Va. Manuscript submitted March 28. 1969. IMD__________________ possesses excellent microstructural stability to 508°C. The effect of lamellar structure in A1-CuA12 eutectic was compared3 to the rod-like structure in the A1-Al3Ni eutectic, and was found to be better in low cycle fatigue. This was rationalized3 by postulating that a lamellar reinforcement was more efficient at blocking lateral plastic flow than a rod-like rein-forcement. The purpose of this study is to explore eutectic strengthening in other aluminum base alloys. The Al-Pd system5 forms a eutectic with aluminum and the intermetallic compound A13Pd at 25 wt pct Pd, and has a melting point of 615°C. A13Pd has an orthorhom-bic structure and transforms to hexagonal Pd2A13 at 785°C. Growth characteristics, compression yield strength, creep rupture, and microstructural stability of directionally solidified and as-cast alloys are investigated. Eutectic ingots having a nominal composition of 25 wt pct Pd were prepared by first compacting 1/2 in. diam by a in. high pellets from 99.99+ pct A1 and 99.99 pct Pd powders. The pellets were then levitation cast into 1/4 in. diam by 2 in. long copper molds. Directionally solidified bars were prepared by grinding the cast ingots to 0.195 in. diam, inserting them into alumina

Jan 1, 1970

By N. A. Gokcen, M. Ohtani

Thermodynamic intevaction pararnetevs of elements E2(2), for dilute binary solutions of a component "2" in liquid iron, i.e., E(22) = 9 In f2/?N2 where f2 is the activity coefficient and N2 the mole fraction, and E(3) 2 = In f2/ N3 dilute ternary solutions of "2" and "3," and the carbon saturation parameter sc(3) (In f c/ N3) N c/N Fe for N3 - 0, are critically examined and correlated. It has been found that the interaction parameters and the atomic numbers of alloying elements follow regular periodic putterns. PHYSICO-chemical behavior of alloying elements in molten iron have become the subject of numerous investigations during the past 25 years. Consequently, the mutual effects of elements in the iron-rich solutions Fe-C-X, Fe-N-X, Fe-H-X, Fe-O-X, and Fe-S-X where X represents an alloying element, have gradually become better understood. These effects for a given temperature and pressure may be expressed by the interaction parameter of Wagner1, 2 derived briefly in the following manner. The complete differential of the Gibbs free-energy equation at constant temperature and pressure is dF = Fl dn, + F2 dn, + F3 dn3+ . . . [ 1] where F is the free energy; F 1, the partial molar free energy of "I"; and n,, the number of moles of "i." Cross-differentiation of this expression* *Cross-differentials are obtained as follows: Since the order of differentiation of F with n2 and n3 is immaterial, the left sides of the second differentials are equal, hence the derivation of Eq. [2] is obtained. For a dilute solution of components 2 and 3 in solvent 1, with the substitution of RT In f i = Fi xs for Fi where fi is the activity coefficient, and Fixs is the excess partial molar free energy, Eq. [2] becomes O) [3] where N2 and N, are the mole fractions. The interaction parameters are defined by

Jan 1, 1961

THE SECRETARY The year 1917 has been a notable one in Institute affairs. The usual activities, including meetings, publications, local section interests, library service, and so-forth, have been continued on at least the same scale as previously, and in addition the resources of the Institute have been placed without stint at the service of the Nation, not only for the active prosecution of the military side of the war, but even more especially in the industrial operations which form the very basis of modern warfare. The officers and directors of the Institute have labored both officially and individually, while the Institute as a body, through committees of, prominent members, and through many individual members, has given freely. Finally, Institute funds have been appropriated to an amount exceeding $5000 to accomplish the cooperation with Government bureaus, and provide committee expenses necessary for performing the services that have been given. The President of the Institute had a very large personal share in many of these activities, which will be described in the following pages, as well as in the President&apos;s own report. Many of the Institute&apos;s members are giving their whole time for. $1 a year, or less, and especial mention should be made of Herbert C. Hoover, Food Administrator, W. L. Honnold, Head of the Commission for Relief in Belgium, Mark L. Requa, Petroleum Administrator, Edgar Rickard and Charles W. Merrill of the Food Administration, S. A. Taylor of the Fuel Administration, W. L. Saunders, B. B. Thayer and Joseph W. Richards who .are giving a. large share of their time to the Naval Consulting Board, W. Y. Westervelt, W.0. Hotchkiss and Harvey S. Mud of the War Minerals Committee, David W. Brunton of the War Committee of Technical Societies, and hundreds of others whose names are mentioned in the Honor Roll of Members. It has also been a notable year in cooperation with sister-societies. The most important event under this head was the accession of the American Society of Civil Engineers into the fraternity of Founder Societies.

Jan 2, 1918

By John Griffen

OF the western European countries, only England has made any extensive use of equipment developed initially by the coal preparation industry of the United States. About 20 years ago, the Chance sand flotation process for cleaning coal was introduced in England, and it has had a fairly wide adoption, particularly in the South Wales coal fields. In recent years, particularly since 1946, a considerable number of Denver flotation cells have been installed throughout the English coal fields for the cleaning of slurry. Until the advent of the Denver cells, the flotation of coal slurries in Western Europe had been done largely with the Mineral Separations cell or its modifications. Kleinbentik of Dutch State Mines had developed a cylindrical cell used in Holland and occasionally in Belgium and France. In England, the establishment of the National Coal Board to control the planning and operation of all coal production has retarded somewhat modernization of properties. A considerable period of study was required before definite long-range plans could be formulated. It was soon recognized that stopgap measures were needed in many cases to bridge the period until final plans could be developed and consummated. One of the stopgap problems in coal preparation was providing plants of small and medium capacity that could be used for a few years at one site and yet could be moved economically to another site so as to reduce depreciation charges per year and per ton. Such plants are being installed but the most satisfactory answer probably has not yet been found. One such installation uses a Norton Baum jig to wash 6 in. to 0. The equipment is in a steel structure rather than in a reinforced concrete frame with brick curtain walls, which is the normal structure for permanent plants. Since England has between 700 and 800 preparation plants for an output of 200 million tons per year, one of the long-range objectives is a consolidation of mine output which will require fewer coal

Jan 1, 1952