Search Documents

By F. F. Peng, A. D. Walters, M. R. Geer, J. W. Leonard

INTRODUCTION Washability characteristics derived from float-and-sink analysis in Chapter 4 demonstrate that coal is intrinsically heterogeneous, and this heterogeneity is also evident in the proximate, ultimate, and size analyses. A range of particles from high to low specific gravity is usually seen in the run-of-mine coal. One objective of coal preparation is to recover the high quality float material (the particles of lower specific gravity) such that the recovered product meets certain quality specifications, as well as to reject or recycle low quality particles of higher specific gravity. The maximum recovery of cleaned coal at the required quality is of major concern to plant operators. However, the quantity and quality of products of coal cleaning, determined in the operation of actual commercial cleaning plants and by theoretical calculation based on run-of-mine washability studies, are known to be different with each coal. Therefore, during the last half century, coal preparation engineers have repeatedly sought methods to predict the technical and economical efficiency of separation of cleaning equipment and systems. Many formulas have been proposed by international investigators to evaluate the efficiency of various coal cleaning operations, primarily based on the yield and/or ash of the various products of coal cleaning. Performance criteria in use today are capable of defining all of the important aspects of a given concentrating operation; however each criterion has certain restrictions or limitations. It is important, therefore, to understand how such formulas can be used and the problems involved in their construction. Technical Measure of Plant Performance Conventional means for evaluating a preparation plant's performance are generally approached through the use of equipment performance mea-

Jan 1, 1979

By Oscar Glaeser

THE mine and plant of the United Verde Copper Co., located in Yavapi County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending-about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level.

Jan 1, 1929

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

The steady-state operation of an isothermal, counter-current reactor in which a mouing bed of hematite particles is reduced by hydrogen has been modeled mathematically using a generalized single-particle kinetic formulation for topochemical reduction with formation of the intermediate oxides, wustite and magnetite. Reduction prof iles have been generated for various oper- REDUCTION of iron ore, as practiced industrially, approaches counter current, granular-bed operation. The total process is extremely complex. Quite under- ating conditions selected to demonstrate the influence of major variables such as gas and solid flow rates, bed length, and particle size. These profiles illustrate , among other things, that the reducing-gas requirement in a countercurrent bed hinges upon the iron-wüstite equilibrium or 'pinch-point" in much the same way as in a staged reactor. standably, nearly all research has been focused on reduction of single particles of oxide under controlled conditions. While this approach simplifies the problem by eliminating interparticle interactions, the remaining intraparticle transport and kinetic processes still constitute a most formidable challenge. Only within the last few years has knowledge of single-particle reactions been developed sufficiently to make modeling of counter current-bed reduction a realistic and useful study of process behavior. The authors have analyzed1"3 extensive laboratory

Jan 1, 1969

By W. H. Burke

Deeper drilling, resulting in greater circulating distance and pressure, has directed attention to the advantages of the study of properties and control of rotary muds, which until recently have not had much consideration. One fundamental property of muds is viscosity, and viscosity is influenced by the quantity and character of colloidal material and can be controlled by chemical treatment. Colloidal Matter of Rotary Muds Two types of colloids are found in muds; the hydrophobic and the hydrophilic. Hydrophobic colloids do not associate intimately with water and are sensitive to small quantities of electrolytes. Hydrophilic colloids associate intimately with water, but are not so sensitive to electrolytes. The colloidal particles of rotary muds are derived from clay; In clay the particles may range in size from submicroscopic to macroscopic; a substance is a clay if the greater proportion of the particles are within the size limits prescribed for clay. The larger particles are inert and have no effect on the viscosity of normal hydrophobic colloidal muds. There are two theories accounting for the colloidal properties of clay-water suspensions: (1) the physical theory, that clay in water is a coarse colloidal suspension, and (2) Ashley's1 theory, that clay is a granular material with a colloidal gel surrounding the crystalline grains. The most important colloidal substances known to exist in clays besides the clay particles are: (1) colloidal silica, (2) colloidal alumina, (3) colloidal ferric hydroxide, (4) colloidal silicates, and (5) colloidal organic matter. Plasticity, a peculiar property of clay-water suspensions, is due to the colloidal particles. It is commonly (although not with strict accuracy) measured in terms of viscosity, and depends upon the amount and the state of flocculation of the colloidal matter present in the suspension. Fluidity in a rotary mud may be caused by a lack of colloidal clay particles or by deflocculated or flocculated clay particles, while viscosity in a

Jan 1, 1935

By Clifford Frondel

THE aluminum oxide known as corundum has several varieties that have been used as gem materials since ancient times. These include the red variety called ruby, the blue variety sapphire, and the asteriated types of ruby and sapphire. Asteriated sapphire was known to the ancients under the name of astrios, and descriptions of this gem were given by Pliny and other early writers. The relation of these gem materials to each other as varieties of a single species, corundum, was first clearly established by Haüy in 1805 and J. M. Güthe' in 1809. Natural gem corundum is obtained principally in Ceylon, Siam, Burma, India, and Australia. Star sapphires and rubies always have been highly prized and in recent years have become particu- larly popular in the United States. Natural star rubies of large size and fine quality are extremely rare and rank with large and fine emeralds and diamonds as the most valuable of gem stones. Interest thus attaches to the recent success in commercially synthesizing star sapphires and rubies of a size and perfection unmatched by nature. Corundum was first synthesized as crystals in 1837 by A. Gaudin, who fused alum and aluminum oxide with potassium sulphate. Numerous other syntheses have been reported in more recent years. Summaries of this work are given in Doelter's Hand-buch der Mineralchemie, Mellor's Compreheizsive Treatise of Inorganic Chemistry, and other reference works. The methods employed include the reaction in the gaseous state at high temperatures of halogen compounds of aluminum with water vapor or boric oxide; the crystallization of aluminum oxide from fusion in potassium molybdate, potassium dichrom-ate or borax; and crystallization from highly aluminous silicate melts. Red, blue, or green colored varieties can be obtained by the addition of small

Jan 1, 1955

Discussion of the paper of E. J. Hall and C. W. Drury, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 78, June, 1913, pp. 1059 to 1066. A. M. SMOOT,* New York, N. Y. (communication to the Secretary +) :-The nails method is given in many text books on assaying as a standard method for gold or for gold and silver in ores. It appears to be taught in the laboratories of technical and scientific schools as a standard method, and to some extent it is used by assayers in actual practice, although the class of ores to which it may be applied is limited to those free from reducible metallic compounds, the metals of which would enter the lead button. The experiments of Messrs. Hall and Drury show the inaccuracy of this rnethod for silver, in heavy sulphides, but not so clearly the short-comings with regard to gold. It seems certain that low silver is caused by the solubility of silver in iron-alkali sulphide as compared with its solubility in molten lead; that is, silver is distributed between iron-alkali sulphide and metal in the charge in proportion to solubility at the particular temperature of the fusion. Lead is a fixed quantity in these assay charges, but iron-alkali sulphide increases with increased sulphur, so the more sulphur in the charge, the lower the silver results.

Jan 11, 1913

By R. R. Hartman, W. B. Agocs

In the course of a return flight from Olympia, Wash., to Laramie, Wyo., an airborne magnetometer profile was recorded continuously. The level of flight was controlled at barometric levels along segments of the flight. Barometric altitude was changed from 3000 ft to a maximum of 12,000 ft above mean sea level to take care of topographic variations. Terrain clearance varied from 800 to 7300 ft. Horizontal positions were obtained by recording and tying to cities, towns, airports, river crossings, and other landmarks in the course of the flight. Figs. 1-6 show the course of the flight and the general geologic and tectonic features traversed. The flight line begins south of Olympia, Wash., and proceeds south across the Puget-Willemette depression to the Columbia River. Thence it proceeds eastward along the Washington-Oregon border across the Cascade Mts. and lava flows and the Umatilla basin to Pendleton, Ore. From Pendleton it traverses the Blue Mts. uplift of Oregon in a southeasterly direction, and then to the Boise basin of southwestern Idaho. The flight line swings in an easterly direction as it passes over the Snake River downwarp to the south of the Idaho batholith. It then passes over the northern portion of the Great Basin and the heavily overthrust area at the intersection of the Utah, Idaho, and Wyoming borders. The flight then assumes an easterly course to cross the series of basins and uplifts of southern Wyoming and terminates near the western flank of the Laramie uplift.

Dec 1, 1956

By Claude H. P. Lupis, John F. Elliott

IN the recent past, extensive use has been made of the interaction coefficient in treating the thermody-namic behavior of components in solutions at dilute concentrations. The development of this concept by wagner1 and chipman2,3 is sufficiently well-known so that its elucidation here is not necessary. The present discussion is focused on the relationship between E and e. The usual forms of the coefficients are:

Jan 1, 1965

By Suresh P. Babu, Joseph W. Leonard

The ultimate objectives of comminution should be to reduce material to some specified size while producing a minimum of undersize or fines, with less power, higher throughputs, and with more compact machinery. Attempts to achieve these objectives have been only partially successful, since gains in some areas are achieved at the cost of concessions in other areas. An example of some of these trade-offs can be found in the closed circuit crushing operations of the anthracite and crushed stone industry where, in order to produce a minimum of unprofitable fines, unfavorable concessions must be made in the size of the crushing facility where 2 or more crushing stages are interphased by 2 or more screening operations. This paper discusses experiments with a new process which attempts to achieve some, if not all, of the comminution objectives in a single pass operation without undesirable concessions; or, at the very least, to achieve more than is possible with systems in use today. These objectives are sought by use of water-flushing to enhance comminution. The crushing of coal and other minerals is a mature technology that is long overdue for a careful re-examination. Crushing of coal is generally achieved through the use of rotary breakers and roll crushers. Water-flushing, as envisioned here, appears to have potential application in the following areas: 1) For primary raw coal crushing or for secondary crushing of rotary breaker products. 2) For use as a size reduction and/or concentrating step for crushing coal mine refuse from present production or from existing refuse dumps. 3) For possible future application in underground preparation interphased with continuous mining machinery. Size reduction with conventional methods is known to be an inefficient operation when the increase in surface energy of the material crushed is compared with the input energy. A simple breakdown of the energy consumption in size reduction, given by Orr, is shown in [Fig. 1]. It is believed that most of the energy supplied is lost in the form of interparticle friction.2 Hence, the removal of fines immediately after their formation or the implementation of steps to prevent their formation, based on reduced friction, will reduce the energy requirements of the communition operation.3 A detailed discussion of the mechanism of size reduction is available in other literature.3-5 Even though the closed circuit crushing operation is designed to carry the fines away from the crushing zone, it is still inadequate for instantaneous removal of fines. The present investigation advocates the use of a flowing liquid medium to remove the crushed product immediately after size reduction. Unlike the wet-grinding methods, no constraints are required for the liquid flow rate, and, also, the liquid medium can be used in primary crushers like jaw crushers, hammer mills,

Jan 1, 1978

By H. S. McQueen

THE central Ozark region of Missouri has inter-ested geologists and mining engineers for many years. Of particular interest are the mineralized sink-hole type deposits, some of which have produced large quantities of iron ore. Deposits of coal are also known in this part of the State, and in mode of occur-rence are similar to the iron ore deposits. Occurring in the same general area, and often associated with coal, are deposits of high-grade non-plastic flint fire clay, and high alumina or diaspore clay. At present these clays are the most important materials being mined from the sink-hole type deposits. Deposits of high-grade flint fire clay have been known to occur in this region for many years, the Kelley pit near Rolla, Phelps County, being discovered in drilling for iron ore shortly after the close of the Civil War. Mining operations had disclosed at an early date masses of rough, open-textured "sandy" clay associated with the flint fire clay. Some of the hard flint clay also con-tained rounded shot-like particles of "sand." Both types of clay were considered of inferior grade and unsuited to the manufacture of fire brick. These clays were discarded in mining as value-less, in some instances being used for road metal. Some knowledge of the high alumina content of this sandy material had been obtained by 1908 1, and by 1917 the high alumina content was gen- erally known, and commercial shipments of what is now called diaspore clay were being made. These deposits of diaspore clay associated with flint fire clay form the only known deposits of commercial importance in North America. The production of diaspore and flint fire clay at present exceeds that of any former year. Statistics covering the production and value of the former were not collected prior to 1922, and the figures given below do not cover the tonnage of clay mined by companies and used in their own plants, so that the total produc-tion probably is much larger than that indicated. The figures were collected by the U. S. Geological Survey and the U. S. Bureau of Mines in cooperation with the Missouri Bureau of Geology and Mines.

Jan 6, 1928

By Donald C. Bradford

THE place of geophysics in the curriculum of a college or an engineering school has been much discussed. There is uncertainty as to whether the graduate may be called a "geological geophysicist" or a "geophysical geologist." Some have used the term "geophysical engineer." The question of the specialized undergraduate curriculum versus a general undergraduate training in the parent sciences with the addition of cultural electives has been and is still being argued. The literature during the past 10 years shows that there are two rather definite schools of thought on this subject. The prospective employer, engaged in active geophysical exploration, visualizes the graduate in terms of the routine work he will do in the field. The school administrator, grounded in many years of tradition in the cultural type of education, visualizes the graduate in terms of his position in a political and cultural society as well as in his work as a professional geophysicist. Both are right and both wrong. A third school of thought, that of the student himself, has been almost totally ignored. It would seem best, for the purpose of this paper, to treat these various points and allied material separately, and then to integrate the conclusions as a set of conditions that should be fulfilled as far as possible in the ideal curriculum. At the end the relationship of our findings to the curriculum that has been tentatively adopted at the University of Pittsburgh will be considered. DIVISIONS IN DEFINITION OF FIELD OF GEOPHYSICS Geophysics is that field of science in which geological and earth problems are solved with the use of physical and chemical techniques. Altogether too much attention has been paid to the artificial separation in this science of the commercial applications from the so-called "pure" or academic geophysics. The only real difference in the two types of work is one of scale of operations. In the commercial field the scale is large in terms of financial backing, immediate economic importance, and speed of operations. In the academic field the scale is large in terms of breadth of interests, in eventual economic importance, and length of time allowable for theoretical investigations. In exploration work the scale is small in terms of dimensions, since the methods are applicable only to the outer 20,000 ft. or so of the earth's. crust. In academic work, the student is not pressed for results of immediate economic importance, and therefore can afford to spend more time on problems that seem unimportant at the time. In the sense of background knowledge of the parent sciences necessary to the geophysicist, no essential difference can be found. Physics, chemistry, geology, and mathematics together, and in their proper proportionate amounts, form the matrix from which geophysical ideas and methods may spring.

Jan 1, 1942

By John C. Robison

INTRODUCTION Sensitivity analysis is a means of gauging the impact of individual risks on a financing. Key risks can occur in three time periods: - Feasibility, engineering and construction phase; - Start up phase (usually through completion); - Operating phase (post completion). If a company has agreed to cover these risks prior to completion, then less attention will be paid to the sensitivity of the project in the first two time periods. Since the operating phase of the project generates cash for both operations and debt service and generally does not begin until two to six years after the loan is signed, it is wise to look at scenarios other than the projected "base-case" scenario in order to determine the project's capability to operate successfully under a broad range of probable future events. Lenders are compensated at a fixed spread over their borrowing base and generally are not compensated if the project is successful beyond expectation. They are also subject to the loss of principal plus funding costs if the project performs below expectation. Because of this, lenders establish sensitivities around the parameters of conservative projections developed in the project feasibility studies and the cash flows resulting from these projections. The initial cash flow projections should demonstrate the project's ability to meet cash costs, debt service requirements (principal and interest), and still have sufficient cushion to cover contingencies such as strikes, price fluctuations, force majeur situations, etc. (See Schreiber, Chapter 10). The selection of the level of sensitivity analysis to be performed is the result of both objective criteria, including probabilistic analysis applied to the technical parameters, and, of equal importance, subjective criteria applied by the analysts, especially with regard to the economic and financial parameters impacting the project cash flows. RISK SENSITIVITY Assumptions used in the cash flow projections should be realistic. Risks identified by the lenders should be identified and cash flows prepared to assess whether these project risks are acceptable. Typical project risks include the following (see also Chapter 9): - Sufficient reserves - quantity and quality - Product price - Production level - Operating costs - Availability of energy and supplies - Transportation and infrastructure requirements and costs - Interest rate - Completion risks - Tax level - Political risks - Cost over-run risks - Operator experience - Management - Technological risks - Environmental permits and risks - Foreign exchange risks - Insurance coverage - Equity of sponsors - Inflation rate - Capital expenditure during project life In order to see the effect on the cash flow projections, each risk should be analyzed for its impact on the cash flow generating capacity of the project. Sensitivities can be examined to see if the resultant cash flow projection will meet the lenders minimum credit standards. 1.Reserve Sensitivity In general, lenders will not assume the reserve risk. However, it should also be noted that lenders receive loan proposals in which reserves range anywhere from proven to possible. Sensitivities are not generally run for various reserve levels and reserve estimates are either considered acceptable or not acceptable by the lenders.

Jan 1, 1985

By Frederick Laist

THE ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaces, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of -copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper;: this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it was found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first-.and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator, produces a product that is self-fluxing; in fact, it is possible to produce a

Jan 1, 1920

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By S. G. Epstein

Using the capillary-reservoir technique, electromi-gvation rates of cadmium and indium in liquid bismuth were measured at several temperatures. The electric mobility of cadmium Jrom 305° to 535°C and indium from 310° to 595°C can be expressed as a function of temperature by the equations UIn = 1.52 x 10-3 exp sq caz per v-sec Migraion of both solutes was cathode-divected at a rate rnore than four tiMes tHAt previously found for siluer in liquid bisnmth. The electric mobilities of cadmium and indiulrz in liquid bismuth at 500° C are nearly identical with their respective mobilities in mercury at room temperature. AS part of a systematic study of the variables which are considered to control electromigration in liquid metals, the electromigration rates of cadmium and indium in liquid bismuth have been measured. Mass transport properties of silver in liquid bismuth have been reported previously,&apos; and measurements of tin and antimony in liquid bismuth are forthcoming. Comparisons will be made with literature values for these same solutes in mercury.2&apos;3 This series of solutes was selected to determine the effect of the solute valence on its electromigration. Silver, cadmium, indium, tin, and antimony have nearly equal atomic masses but have chemical valences ranging from +1 to +5. They are all fairly soluble in bismuth above 300°C and all have radioactive isotopes, which are an aid in making analyses. EXPERIMENTAL TECHNIQUE Electromigration of cadmium and indium in liquid bismuth was measured by the modified capillary-reservoir technique previously described.&apos; In this method irradiated cadmium or indium is added to bismuth to form alloys containing about 1 wt pct solute (<2 at. pct solute). Several quartz or Pyrex capillaries: 1 mm ID and 5 cm long, vertically oriented, are simultaneously filled in the reservoir of the liquid alloy. A direct current is passed through two of the capillaries, which contain tungsten electrodes sealed in the upper end. The other capillaries sample the reservoir during the experiment. After a measured time interval the capillaries are removed from the reservoir and rapidly cooled. The glass is then broken away from the solidi- fied alloy, which is then weighed, dissolved in acid, and analyzed for solute content by chemical and radiochem-ical techniques. An electric mobility (velocity per unit field) can be calculated from the amount of solute entering or leaving each capillary by the simplified expression1 in which Ui is the electric mobility of the solute, ?mi the solute weight change, Ci the solute concentration of the reservoir, I the current, p the alloy resistivity, and l the duration of the experiment. This expression is valid as long as the experiment is terminated before a concentration gradient develops across the capillary orifice. Earlier experiments showed that the concentration gradient formed initially at the electrode changes with time and eventually reaches the orifice, due to back-diffusion. This condition produces a solute exchange between capillary and reservoir by diffusion or convection, opposing the electromigration, which results in a lower measured value for the electric mobility. To determine if the concentration gradient had reached the orifice, the capillaries used in some of the experiments were sectioned at 1-cm intervals and the solute content of the alloy from each section was radiochemically determined. A typical concentration profile for an experiment with indium in bismuth is shown in Fig. 1; cadmium in bismuth showed similar behavior. As illustrated in the graph, very little back-diffusion has occurred in the capillary containing the cathode, since the concentration gradient is confined to the upper 1 cm of the capillary. In the capillary containing the anode, however, the concentration gradient is much broader, extending nearly to the orifice, even though the net change in solute concentration is nearlv the same in both capillaries. Since cadmium and indium probably lower the density of bismuth when alloyed, depletion of the solute from the alloy adjacent to the anode would increase the density of the liquid in the uppermost region of the capillary. This would give rise to convective mixing within the capillary, causing the broadened concentration gradient. Conversely, the alloy adjacent to the cathode should have a reduced density as the solute concentration is increased by migration, explaining the "normal" concentration profiles found in these capillaries. This disparity was not found for electromigration of silver in bismuth. Both metals have similar densities at the operating temperatures, and nearly symmetrical concentration profiles were found in the two capillaries of each exueriment. This density effect was also apparently encountered when an attempt was made to measure diffusion coefficients for indium in liquid bismuth by the same technique which was successfully used to measure diffusion of silver in bismuth.&apos; Capillaries 1 mm ID and 2 cm

Jan 1, 1968

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250&apos; to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,&apos; and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By R. B. Roof, J. J. Lombardo

DURING the course of investigations on U-Cb alloys by X-ray diffraction techniques, an impurity or an additional phase was observed in severa1 alloys of various compositions. The X-ray dif-

Jan 1, 1959

By Louis Huntoon

THE USE of the aeroplane in engineering work is quite recent. Its general application to all branches of engineering, including mining and metallurgical engineering, is increasing and its possible uses are most promising. Comparatively little has been published on the sub-ject in the mining and metallurgical press, and it is for this reason that the following notes are recorded. In March, 1922, Prof. E. L. Bruce published an article in the Transactions of the Canadian Mining Institute showing the possible applications of the aeroplane to preliminary geological surveys. In October, 1922, Mr. DeShea, representative of the Fairchild Aerial Survey Co., of New York, discussed the subject before the New York Section of the Mining and Metallurgical Society. The writer has been in correspondence with the Laurentide Air Service of Montreal and engineers who have flown. Canada, with its many lakes and rivers-favorable landing places, meets the prerequisite for successful use of the aeroplane in an unexplored and uninhabited or sparsely inhabited country. During the open season hydroplanes are used, and during the, winter season ski runners are attached to the axle in lieu of wheels. With skiis attached it has been found practicable to take off and land on any depth of snow quite readily. Winter flying in northern Canada is quite common. The Laurentide Lumber Co., appreciating the value of the aeroplane, used them for two or three years for timber cruising, and about 1921 turned their equip-ment over to the Laurentide Air Service of Montreal, who operate flying machines. The photographic and engineering work in Canada is done by the Fair-child Aerial Surveys Co. under a contract with the Laurentide Company.

Jan 12, 1923

By Richard H. Jahns

GRANITIC pegmatite deposits are the chief source of commercial feldspar, sheet mica, beryllium, tantalum-columbium, and lithium minerals, and certain types of kaolin. They also have yielded significant quantities of cassiterite, gems, scrap mica, molybdenite, tungsten minerals, uranium-thorium and rare-earth minerals, and zircon, either directly or as the sources of placer deposits. The output from pegmatite mines in the United States is small as compared to other mineral products in terms of bulk or value, and much of it comprises minor metals and nonmetals. Nevertheless, pegmatite minerals play a vital part in domestic industrial economy, particularly in the ceramic and electrical industries. Numerous special purpose uses also are important, even though they require small quantities of raw materials. Never was United States dependence upon pegmatite mining more clearly emphasized than during World War 11, when greatly expanded demands and uncertainties of foreign sources of supply caused much concern. Such commodities as beryl, tantalite, and sheet muscovite remained high on the critical list for months at a time, and for some minerals there was a real struggle to achieve and maintain a favorable ratio of supply to demand. Satisfactory stock piles of certain sizes and qualities of sheet mica, for example, were not built up until late in 1944, when wartime requirements already had begun to level off or even to decrease. Production of all the strategic pegmatite minerals from domestic deposits during World War I1 constituted only 10 pct or less of the total domestic consumption of these minerals, but the importance of this contribution should not be minimized. Domestic production often represented the difference between increase and further reduction of existing stocks of commodities already in seriously short supply, and in the early stages of the war it was the only assured source if imports were cut off. During the recent war period, the U. S. Geological Survey carried on a program of pegmatite studies in the New England and Southeastern States, in the Black Hills area of South Dakota, in the Rocky Mountain region of Wyoming, Colorado, and New Mexico, and in various parts of Washington, Idaho, Utah, Nevada, Arizona, and California as shown in Fig. 1. Several papers and reports already have appeared as an outgrowth of this work,&apos;-= and others are in preparation. This paper outlines some results of data obtained by the writer during the period 1942 to 1946, when he was engaged in studies of pegmatites in the Southeastern, Southwestern, and Rocky Mountain States. Beryllium Minerals Beryl is the present commercial source of beryllium metal and beryllium compounds, which are used in ceramics, in the preparation of X-ray tubes and fluorescent lamps and screens, in special processes of paint and textile manufacture, and in the optical systems of some electrical instruments. The metal also is used in nuclear physics, chiefly as a source of neutrons. Beryllium is alloyed with aluminum for certain light-metal uses and is a constituent of some nickel and iron alloys. Currently the chief demand, however, is for copper-base alloys, which are exceptionally resistant to fatigue and wear, are responsive to hardening treatments after

Jan 1, 1952