Search Documents

By R. B. Yerxa, C. F. Green, H. O. Hofman

MASSACHUSETTS INSTITUTE OF TECHNOLOGY, In refining copper, the metal is melted down in a reverbera tory furnace in a more or less oxidizing atmosphere and then further subjected to an oxidizing smelting in order to eliminate the common impurities, most of which have a stronger affinity for oxygen than has copper. In these operations some of the copper is oxidized to cuprous oxide and dissolved by the metal bath. When the quantity of dissolved cuprous oxide has reached about 6 per cent, the metal is said to have been brought to " set-copper." A button-sample will show a depressed surface and, when broken, a single bubble at the apex of the depression; the fracture will be brick-red and dull. It is essential to carry the oxidation to this point in order to know that the impurities have been oxidized as far as it is possible under the given working-conditions. Nearly all the cuprous oxide of the set-copper is now reduced to the metallic state by poling, when "tough-pitch" copper will be obtained. A button-sample will show a flat surface. Upon breaking, it will be found that the former bubble has disappeared and that the fracture has become rose-colored and shows a silky luster. The quantity of cuprous oxide allowed to remain in the copper will vary with the impurities still present in the metal and with the degree of pitch that it is desired to reach. It is essential for the general physical and the mechanical properties of the resulting copper that such impurities as arsenic, antimony, bismuth, lead shall be present in the oxidized state, as they are

Jan 1, 1904

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By W. M. Bertholf

IN 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral can make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory," as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,1 but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1946

By C. E. McCarthy, A. George Stern, Stanley J. Green

THE national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of I9I4-I8 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. WYOMINGITE DEPOSIT For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the southwestern part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world's largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, I2; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the wyomingite has a potash content averaging slightly higher than eleven per cent K20. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1944

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By Frank C. Schrader

Page Introduction.............................. 196 Geology of the District......................... 196 Ore Deposits of the District....................... 198 Gcncral Description........................ 198 The Cerbat Mountains Group................... 199 General Description...................... 199 Tennessee Mine....................... 203 Midnight Mine........................ 203 Mineral Park........................ 204- Golconda Mine........................ 204 Other Ore-bearing Districts.................. 205 Lost Basin District ...................... 205 The Black Mountains Group.................... 206 Tom Reed-Gold Road District...................... 208 General Dcscription........................ 208 Development........................... 209 Topograplly............................ 210 Geology.............................. 210 Ore Deposits........................... 213 General Dwcription...................... 213 Zones.......................:....215 Structure of Ore Shoots.................... 217 Gold Road Mine ......................... 218 General Description...................... 218 Geology........................... 218 Ore Deposits......................... 219 Tom Reed Minc......................... 222 General Description..................... 222 • Ore Deposits.......................... 222 Development......................... 223 Character of Ore....................... 224 Other Mines........................... 224 Fields Similar to the Ton1 Reed-Gold Road District......... 227

Jan 1, 1917

By Lauren A. Wright

SINCE the early nineteen-thirties the production of talc* in California has increased five-fold to a yield in 1947 of about 76,000 tons (fig. 1); conse- .' Unless otherwise qualified, the term "talc" in this paper will imply a mixture of the pure talc with such related minerals as commonly occur in the commercial material. quently the state is now one of the nation's three principal talc producers. The 1947 output, which represented about one-sixth of the national total for that year, was approximately equal to production from Vermont, and was second in value to that from New York. New York has an annual output of about 130,000 tons. Three factors have been mainly responsible for the expansion of talc production in California. (1) Technical advances and innovations, particularly in the ceramic industry, have increased the demand for certain California talcs. The nation's high-qual- LAUREN A. WRIGHT, Junior Member AIME, is Associate Geologist, California Division of Mines, San Francisco, Calif. Los Angeles Meeting, October 1948. San Francisco Meeting, February 1949. TP 2622 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscripts received Dec. 7, 1948; revision received Aug. 29, 1949. This paper is Contribution No. 508 of the Division of Geological Sciences, California Institute of Technology, Pasadena, Calif. the industry, mainly through demand for the urgently needed steatite. Fibrous talc, used as a paint extender by the armed forces, also was produced in quantity. (3) Expanding western industry has continued to draw heavily on California talc deposits, and has extended the upward production trend into the postwar period. Considerably more than half of California's current talc output is used as ceramic raw material. The paint, rubber, paper, and textile industries are the more important consumers of the remainder. Smaller amounts are used as insecticide carriers, and in cosmetics, and various minor industrial applications. During World War I1 the principal steatite deposits were studied in detail by members of the U. S. Geological Survey; other sources of commercial talc in the state have in the past received but scant geologic attention. The following discussion is essentially a preliminary report based on research currently in progress by the California Division of Mines, and includes a brief outline of previous steatite studies by the U. S. Geological Survey. Distribution of California Talc Deposits: The principal talc resources of both California and Nevada are confined to an elongate belt that extends from the vicinity of Baker, in north-central San Bernardino County, northwestward to include the southern Death Valley region, the Inyo Range, and the Palmetto-Oasis district of western Nevada (fig. 2). This belt, of which all but the northernmost tip lies in California, is approximately 200 miles long and 30 miles in average width. Included in the belt are four contrasting areas. The deposits within each area are geologically similar and yield talcs that have characteristic properties and applications. Three of these local "talc provinces" lie within California's portion of the talc-

Jan 1, 1951

By W. Hurst, A. F. van Everdingen

A distillate-bearing sand complex is often made up of sand stringers of different permeabilities. In order to take into account the influence of the different permeabilities, "parallel flow" is defined, and this concept is used to compute the recovery efficiency of recycling such a sand complex. In the first approximation the position of the wells with respect to one another is not considered. In order to compute the effect on the recovery efficiency of the position of the wells, the area of a field is considered to be made up of rectangles; each rectangle containing one input well in the center and two producers located symmetrically with respect to the input well. Formulas are given from which to obtain the pressure and streamlines in a steady-state flow. A method is devised to compute rapidly the successive positions of the dry gas front. If the field is irregular in shape, pressure and streamlines can be obtained by a potentio-metric electrical model study. By using the concept of "parallel flow" and the results obtained by mathematical analysis or by electrical model study for a homogeneous formation, the effects of different permeabilities and of the location of the wells can be established. From these studies it is apparent that the efficiency of recycling can be profoundly influenced by differences in permeability among the various parallel strata. Introduction With the discovery of an increasing number of gas-distillate fields in the Gulf Coast, engineers have had occasion to give more thought to the performance of these reservoirs, as evidenced by the literature published in recent years. In the majority of studies published so far the formations are considered to consist of uniform, homogeneous sand. In this paper the authors wish to bring out the effect of variations in the permeability of the formations on the over-all recovery efficiency of wet gas in cycling operations. The importance of the permeability profile is clearly indicated by the fact that in gas cycling, highly permeable stringers in an otherwise tight sand can allow complete displacement of wet by dry gas in these stringers long before the wet gas in the tight portions of the sand is displaced. This by-passing will be reflected by a reduction in the condensate content of the production sooner than can be anticipated from a mathematical analysis or an electrical model study on uniform sands. Electrical model studies or mathematical analyses cannot take into consideration the manifold variations of permeability within the reservoir. Experimental as well as analytical difficulties make it necessary to consider the prototype for either of these studies as a perfectly uniform sand. Mathematical analyses are applicable only when a reservoir can be divided into units of simple geometrical form, of uniform thickness throughout. Electric model studies are capable of giving information on reservoirs of any shape or thickness, but it is essential that the sand be considered homogeneous, so that three-dimensional flow can take place. The method of approach in the following

Jan 1, 1946

By Harry Gard Knox, F. R. Harris

This paper covers some of the problems presented to the oil industry in the drilling of oil wells in the open waters of the Gulf of Mexico. The hazards, delays and relative costs of offshore drilling are reviewed and various forms of drilling platforms discussed. The requirements of the offshore drilling rig are summarized together with the principal items affecting the cost of construction. Sea waves and their size and characteristics as affecting offshore platforms are reviewed. Drilling platforms are classified as fixed, or fixed and floating. Fixed platforms of the conventional cofferdam and pile-supported type are discussed together with their good points and their limitations. The desirability is pointed out of eliminating as much offshore work as possible where operations are subjected to constant and expensive delay and substituting therefor the prefabrication of structures ashore or in sheltered waters. Marked economy will come with the standardization of offshore rigs aid special means of transporting them to the site. Several types of structure which are partly pile-supported and partly buoyancy-supported are discussed and their possibilities of future usefulness commented upon. General Considerations The predominant attribute of offshore drilling equipment is that it must be equal to the job in hand. We therefore give first thought to the matter of adequacy. In view of the probable depth of drilling, the investment involved and the per diem labor costs, it is assumed heavy modern drilling equipment will be employed. In order to usc such equipment efficiently, the working deck must be ample in size and strength and supported so as to be relatively free from motion and from green seas even in heavy storms. These requirements necessitate a high and rigid land-based support for the drilling rig and machinery with plenty of space for supplies, such as pipe, mud, water and fuel, with reserves for days when transportation from shore is impracticable. In offshore rigs the crew will be housed onboard in comfortable quarters, probably air conditioned and equipped with a galley and refrigerated food storage. An important consideration will be the ability to transfer stores and crew to and from the rig in all but the heaviest weather and the platforms must be protected from the impact of supply vessels when alongside. It will be essential to maintain continuous communication with shore by radio or cable, not forgetting the possibility of a helicopter landing space for the transfer of crew and light stores as well as a means of general communication. Whatever structure is constructed must be secure from storms of hurricane force and a safe place for the operating crew to work. If the well comes in, the drilling rig will presumably be removed and a small but rugged pile-supported platform will remain to carry the Christmas tree with safe working space around it. It will be protected from damage on all sides by buffer piles or dolphins. It is assumed that the flowing oil will be piped to storage tanks in the vicinity of the well. An individual tank for each well or a

Jan 1, 1949

By R. F. Evans, J. M. Avery

MUCH has been written of the glamour of magnesium from sea water, the Aladdin-like creation of a huge magnesium plant in the Nevada desert using cheap hydroelectric power from Boulder Dam; the marvels of the Hansgirg process for the electrothermal reduction of magnesium oxide by carbon, and the ferrosilicon process for producing magnesium from dolomite. This is the story of the production of -magnesium by the electrolytic process, using steam-electric power supplied by a public utility, in a plant at Painesville, Ohio, 30 miles east of Cleveland on the shore 'of Lake Erie. The story is not without interest, since it involves several unique developments that provide the answer to a question frequently asked: How is it possible to produce magnesium metal economically at such a location as Painesville, Ohio? Basically, the answer lies in making use of facilities already in existence for the production of soda ash, which makes it possible to manufacture magnesium chloride, the principal raw material, cheaply enough to offset the high cost of electric power. To this is coupled the successful conversion of by-product chlorine into a product required for the war program. The source of magnesium for this operation is the enormous surface deposit of high-grade dolomite in the region south of Toledo, within reasonable freight haul of Painesville. This same geological stratum underlies the Painesville plant, but unfortunately at a depth of about 3000 ft. apparently too great a depth to permit underground mining to compete with the delivered cost of rock from surface quarries in other areas. The cost of dolomite obviously is an important factor, since the rock contains only some 12 per cent magnesium (20 per cent MgO) so that one dollar on the cost of stone means more than $8 in terms of its magnesium content, and more than that in terms of recoverable magnesium metal. PRODUCTION OF MAGNESIA FROM DOLOMITE In the summer of 1941, the Diamond Alkali Co. was well along with construction of a plant intended for the commercial production of refractory and other grades of magnesia from dolomite. The process to be used was designed to make maximum economic advantage of existing plant and operations by tying the production of magnesia in with the manufacture of soda ash in such a way as to make use of the lime (CaO) value of calcined dolomite. The process finally adopted after a lengthy research and development program has much in common with the old Clerc-Nihoul process, but includes certain innovations found to be necessary or

Jan 1, 1945

The Hadsel Mill. By R. G HALL (Trans, vol 112 4000 words) This mill is designed to effect the entire reduction of ores by combined crushing and grinding from mine run size to material sufficiently fine for the usual operation of flotation or cyaniding The work is begun and completed in the same machine. The machine is designed on the principal of the elevator wheel, and crushing and grinding are accomplished by dropping a mixture of ore and water upon specially placed "breaker plates" in such a manner that the resultant material passes back into the buckets of the wheel for further elevation One method of removal of the finished product is to permit an overflow of wet pulp on one side of the mill through coarse screens A recent improvement provides for the removal of a pulp by a launder part way up the path of the buckets In either case the pulp passes to a classifier, and the oversize back to the mill in the manner familiar in ball-mill practice Although hardly through the development stage, the machine has given a very good account of itself in simplification of plant, by elimination of coarse and fine crushers with consequent reduction of installation cost and power consumption As compared with the ball mill alone, there is a reduction of power consumption as well as a material reduction of grinding steel There is an increase in cost of maintenance other than grinding steel, but as the machine passes out of the development stage there is a show¬ing of reduction of costs on this item It seems probable that with further develop¬ment and strengthening of the weaker parts further improvement may be made Ball Milling. By A. M Gow, M GUGGENHEIM, A. B. CAMPBELL AND W. H COGHILL. (Tech Pub 517; also Trans, vol 112. 24,000 words) This paper outlines a new philosophy in ball milling by using power as an index of mill operation and ascertaining the effects of the set and induced variables By recognizing the amount of ore in the mill as an important induced variable and recognizing that the amount of ore in the mill depends principally on the size of the discharge trunnion, ball volume, rate of feed, and speed of mill, obstacles formerly met were surmounted When the amount of ore in the mill is dealt with intelligently and the applied work is proportional to the amount of feed, series testing, which would otherwise give a hotchpotch, gives concordant results The study of ball paths and trajectories was seen to be fruitless when it was shown that the old attrition theory for slow mill speed

Jan 1, 1935

By Lauren A. Wright

SINCE the early nineteen-thirties the production of talc* in California has increased five-fold to a yield in 1947 of about 76,000 tons (fig. 1); conse- .' Unless otherwise qualified, the term "talc" in this paper will imply a mixture of the pure talc with such related minerals as commonly occur in the commercial material. quently the state is now one of the nation's three principal talc producers. The 1947 output, which represented about one-sixth of the national total for that year, was approximately equal to production from Vermont, and was second in value to that from New York. New York has an annual output of about 130,000 tons. Three factors have been mainly responsible for the expansion of talc production in California. (1) Technical advances and innovations, particularly in the ceramic industry, have increased the demand for certain California talcs. The nation's high-qual- LAUREN A. WRIGHT, Junior Member AIME, is Associate Geologist, California Division of Mines, San Francisco, Calif. Los Angeles Meeting, October 1948. San Francisco Meeting, February 1949. TP 2622 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscripts received Dec. 7, 1948; revision received Aug. 29, 1949. This paper is Contribution No. 508 of the Division of Geological Sciences, California Institute of Technology, Pasadena, Calif. the industry, mainly through demand for the urgently needed steatite. Fibrous talc, used as a paint extender by the armed forces, also was produced in quantity. (3) Expanding western industry has continued to draw heavily on California talc deposits, and has extended the upward production trend into the postwar period. Considerably more than half of California's current talc output is used as ceramic raw material. The paint, rubber, paper, and textile industries are the more important consumers of the remainder. Smaller amounts are used as insecticide carriers, and in cosmetics, and various minor industrial applications. During World War I1 the principal steatite deposits were studied in detail by members of the U. S. Geological Survey; other sources of commercial talc in the state have in the past received but scant geologic attention. The following discussion is essentially a preliminary report based on research currently in progress by the California Division of Mines, and includes a brief outline of previous steatite studies by the U. S. Geological Survey. Distribution of California Talc Deposits: The principal talc resources of both California and Nevada are confined to an elongate belt that extends from the vicinity of Baker, in north-central San Bernardino County, northwestward to include the southern Death Valley region, the Inyo Range, and the Palmetto-Oasis district of western Nevada (fig. 2). This belt, of which all but the northernmost tip lies in California, is approximately 200 miles long and 30 miles in average width. Included in the belt are four contrasting areas. The deposits within each area are geologically similar and yield talcs that have characteristic properties and applications. Three of these local "talc provinces" lie within California's portion of the talc-

Jan 1, 1951

By W. Hurst, A. F. van Everdingen

A distillate-bearing sand complex is often made up of sand stringers of different permeabilities. In order to take into account the influence of the different permeabilities, "parallel flow" is defined, and this concept is used to compute the recovery efficiency of recycling such a sand complex. In the first approximation the position of the wells with respect to one another is not considered. In order to compute the effect on the recovery efficiency of the position of the wells, the area of a field is considered to be made up of rectangles; each rectangle containing one input well in the center and two producers located symmetrically with respect to the input well. Formulas are given from which to obtain the pressure and streamlines in a steady-state flow. A method is devised to compute rapidly the successive positions of the dry gas front. If the field is irregular in shape, pressure and streamlines can be obtained by a potentio-metric electrical model study. By using the concept of "parallel flow" and the results obtained by mathematical analysis or by electrical model study for a homogeneous formation, the effects of different permeabilities and of the location of the wells can be established. From these studies it is apparent that the efficiency of recycling can be profoundly influenced by differences in permeability among the various parallel strata. Introduction With the discovery of an increasing number of gas-distillate fields in the Gulf Coast, engineers have had occasion to give more thought to the performance of these reservoirs, as evidenced by the literature published in recent years. In the majority of studies published so far the formations are considered to consist of uniform, homogeneous sand. In this paper the authors wish to bring out the effect of variations in the permeability of the formations on the over-all recovery efficiency of wet gas in cycling operations. The importance of the permeability profile is clearly indicated by the fact that in gas cycling, highly permeable stringers in an otherwise tight sand can allow complete displacement of wet by dry gas in these stringers long before the wet gas in the tight portions of the sand is displaced. This by-passing will be reflected by a reduction in the condensate content of the production sooner than can be anticipated from a mathematical analysis or an electrical model study on uniform sands. Electrical model studies or mathematical analyses cannot take into consideration the manifold variations of permeability within the reservoir. Experimental as well as analytical difficulties make it necessary to consider the prototype for either of these studies as a perfectly uniform sand. Mathematical analyses are applicable only when a reservoir can be divided into units of simple geometrical form, of uniform thickness throughout. Electric model studies are capable of giving information on reservoirs of any shape or thickness, but it is essential that the sand be considered homogeneous, so that three-dimensional flow can take place. The method of approach in the following

Jan 1, 1946

By T. Reed Scollon

Coal reserves of the Rocky Mountain area are vast and are more than adequate to meet significantly increasing demands in the immediate future. Practically all of the increase in coal demand for the next decade or so will be in the electric power utility sector. All ranks of coal are available in the area, and from a technological viewpoint, all are suitable for electric power generation. Location of economically recoverable coal deposits, location of generating plants with respect to power demand areas and sources of cooling water, and availability and price of other fuels are the major factors which, individually or in combination, will determine the ultimate selection of Western coal deposits to be developed for electric power generation. The low sulfur content of most western coals and the non-urban location of many power plants should tend to minimize problems of air pollution. If projections for nuclear power prove correct, increases in demand for Rocky Mountain area coals beyond about 1980 will depend primarily on the extent of commercial development of synthetic fuel processes. Current research activities on the conversion of coal to liquid and gaseous fuels are promising. Most western coals range in rank from lignite through high-volatile bituminous coals and are particularly amenable to conversion. Vast reserves of Rocky Mountain coals have long lain dormant primarily because of their remoteness from major market areas. Recently, however, innovations in coal transportation and electric power transmission methods, combined with unprecedented demands for electric power in the West, have resulted in large-scale development of some of these coals. In the past few years, announcements of coal mine openings and transportation plans in the Southwest have been filled with superlatives: The Navajo mine in northwest New Mexico is expected to be the largest mine in the country in the near future. The largest single coal agreement ever made provides for coal shipment from northeast Arizona to Nevada via the largest and longest coal-slurry pipeline ever used. An 1100-mile haul of coking coal from northern New Mexico to California by unit train began last year. It is the purpose of this report to evaluate the coal resources of the Rocky Mountain area, and to project their potential utilization. In projecting energy demand levels on a national basis, the Bureau of Mines has developed some rather complex techniques to cope with uncertainties. Using these same techniques, an estimate has been made of consumption of Mountain area coal in 1980. No attempt was made to estimate coal consumption beyond 1980, but new market potentials are discussed briefly. The present and potential coal-producing fields of the Rocky Mountain area are in six states comprising the Mountain Region - Arizona, Colorado, Montana, New Mexico, Utah, and Wyoming. Since approximately 19% of the coal produced in these fields is shipped to the Pacific Region (Washington, Oregon, Cali-

Jan 1, 1969

By R. F. Mehl, J. K. Stanley

THE recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are employed.1 Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystallization is not a heterogeneous reaction within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress .4,5† The theory of recrystallization is not in advanced state; if recrystallization data were obtained in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed .27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert measurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now

Jan 1, 1942

By Henry Fay

THE erosion of guns is a complex problem which can be solved only by a detailed study of all the factors involved. In the present paper it is proposed to submit the results of observations and experiments which have extended over several years. Certain facts have been established and preliminary reports have been published.' Conclusions have been reached since then which, it is believed, are worth presenting for the purpose of promoting discussion, and with the hope that ultimately the whole truth will be known. The particular phase of the problem which will be presented here is the hardening of the inner surface of the gun tube. It has been known for a long time that after firing a large caliber gun for some time, the surface of the metal becomes hard and brittle, cracks, and wears away.2 The character of this phenomenon may be learned by an examination of some results which are typical, obtained from a detailed study of a 12-in. gun. The gun was trepanned and rings representing various sections of the gun were cut out for examination. The first ring represented the metal at the muzzle end, and the other rings were removed at approximately 120, 240, 325 and 337 in., respectively, toward the breech end. The appearance of the surface of the metal in the different sections is shown in Fig. 1. The greatest amount of wear and maximum amount of hard surface layer was found in section marked E, which is nearest the powder chamber and at the beginning of the rifling; the maximum amount of cracking in D; the maximum amount of copper deposition in C. Section B showed heat cracks on both lands and grooves, and section A showed heat cracks on the driving edge of the lands only. There was much flow of metal in both sections E and D, and there was progressively less effect noticeable toward the muzzle end. The polished cross-section of these same pieces is shown in Fig. 2. The

Jan 12, 1916

Since the beginning of the 20th century the world has been trying to find a new political system, even as it did at the end of the 18th century. The French Revolution instigated the destruction of absolute monarchies when Napoleon unwittingly showed the masses the advantages of freedom, as opposed to the abuses of unlimited power by the imperialists. In spite of advances in culture, science, and technology during the past 50 years, there is a hangover of laissez-faire economic principles. Failure to divert the trends of minority pressure groups has caused two world wars and is the basis for the current social unrest and turmoil. In the ebullition of ideas there have risen to the surface the dregs of ideas, old and new-Nazism, Fascism, Russian Communism-a hodgepodge of imperialistic, socialistic, communistic and capitalistic maneuverings where state monopoly of capital enables ruthless exploitation of the masses. The United States owes much of its industrial greatness to the work of pioneers in the mineral industries. The task of the pioneer was to locate and develop in a rude way the mineral resources of the nation. Today, mineral industries leaders are still in great demand, but for a different purpose-to direct intelligent utilization of the limited, waning, submarginal mineral resources. Today the need is for trained earth scientists, mineral

Jan 1, 1950

By Frank Somogyi, Donald H. Gray

Techniques for in-situ dewatering of tailings and slimes include evaporation, decantation, drainage under self weight, drainage by surcharging, and electro-osmosis. A promising technique for increasing drainage efficiency is a vertical, wall-drain system, which can be constructed in an impoundment concurrently with deposition of slurried tailings. The vertical drains, which can be constructed from sand or from the coarse fraction of a tailings stream, greatly speed the rate of consolidation of the fine tailings or slimes. The performance of a wall drain system and the semitidy of consolidation efficiency to certain variables or system parameters are examined. These parameters include the slime deposition rate, ratio of drain to slime permeability, drain width, and drain spacing.

Jan 1, 1979

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, )"Why automate?" Automation, automatic control devices and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with a minimum of instruments for the purpose of merely guiding the operators. Processes were manually controlled by the operator on the basis of simple temperature, pressure, flow and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction savings in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material through- put, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins or producing a new and saleable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure, and (2) units which both measure and control a process variable. In coal processing, the first class of instruments, those which measure only, include analytical devices such as automatic ash, moisture and sulfur measuring units and the simple pressure, temperature, flow and level indicating devices mentioned previously. The second group of instruments, those which both measure and control, include a wide variety of units such as continuous weighing devices on conveyor belts and photoelectric cells which gauge the position of railroad cars on the track and insure that the cars are in the proper location for loading (see Chapter 15). The latter types of units as used in the coal industry differ from those used in other industries in one significant point. In coal processing these instruments need not be as highly sophisticated and accurate as in other industries; hence their cost is proportionately lower than in other industries. Because of the economic fact that coal sells for only a fraction of a cent per pound compared to dollars per pound for many chemical products, and

Jan 1, 1968

By H. J. O’Donnell, B. C. Parks

IN 1930 the late Dr. Reinhardt Thiessen set up a method of microscopic analysis and type classification of coal that has since been followed as standard practice in the coal-petrography laboratory of the Bureau of Mines. Thiessen's terminology which designated the constituent parts of coal in terms of botanical origin was introduced in 1920.l The technique, however, of preparing a completely representative series of thin sections from a column sample of coal for use in making quantitative determinations of coal components with a microscope was developed about 10 years later by Thiessen and coworkers G. C. Sprunk and H. J. O'Donnell.2 Complete thin-section analyses subsequently have been made of 126 column samples of various ranks and types of American coals. The data and information were assembled from these thin-section studies and published in a large number of reports dealing chiefly with investigations of the coking and hydrogenation properties of certain American coals. In the years following adoption of Thiessen's method, a considerable amount of work was done in collecting column samples of many coals, making routine thin-section analyses of these, interpreting the results, and finding practical application for the information in other fields of coal research. The many reports and papers covering the work in coal petrography, however, offer very little discussion that can be considered as critical appraisal of the technique. Criticism outside the Bureau most often has voiced questioning opinions concerning the accuracy of the method used of measuring coal components microscopically and classifying the coal into arbitrary types on the basis of the quantitative determinations. The principal purpose of this paper is to discuss in some detail and present data showing the results of certain investigative work done in the petrography laboratory on the accuracy of the Bureau's method of microscopic measurement of components in coal thin sections. Data from microscopic analyses on file made by G. C. Sprunk and H. J. O'Donnell were freely used in the investigation, and a table of columnar analyses from an unpublished manuscript by Sprunk is included in this paper for reference. In the course of the experimental work a method was developed for measuring instrumentally with a planimeter the components shown in micrographs of selected thin sections. Measuring coal components with a planimeter furnished useful information for studying the accuracy of microscopically measuring the same components in thin sections. PETROGRAPHIC COMPONENTS AND TYPE CLASSIFICATION OF COAL Thiessen considered coal to be composed of two visibly different major components present in various types of coal in greatly varying proportions. He named

Jan 1, 1948