Search Documents

By Robert G. Nisle

In conducting a pressure build-up test on an oil well, it is often necessary to shut-in the well for a short time prior to initiation of the test. The effect of such a short tern shut-in on the resulting pressure build-up curve is derived. The derivation is based on the Kelvin point-source solution and is a straight forward extension of the fundarnental theory. The magnitude of the effect is evaluatecl and illustrated by an example. It is shown that if the production subsequent to the short term shut-in is at least 10 times the duration of the shrct-in, the effect will he less than 10 per cent. INTRODUCTION It often happens that before a pressure build-up test can be made an additional valve must be mounted on the wellhead, or on arrival at the well, it might be learned that the well had been shut-in several hours the previous day because of a shortage of tankage. In such cases the question is How will such an interruption of production affect the results of a pressure buildup test This work explains how to take account of such a short term shut-in in order that the test can proceed without further delay. The solution presented here makes use of the Kelvin point-source solution used by Horne1 in his treatment of the pressure build-up in wells. Use is also made of the super-position theorem. MATHEMATICAL DERIVATION The well is assumed to have been in production at a constant rate for a relatively long time (several days or more). It is then shut-in for a short time, after which it is again placed in production at the previous constant rate. It continues to produce at this rate until shut-in for a pressure build-up test. The Kelvin point-source solution is expressed by Eq. 1. The sequence of production rates is listed in Table I. TABLE 1 — SEQUENCE OF PRODUCTION RATES Time interval Production Rate At time AT the pressure will be the resultant of the sequence of production rates shown in Table 1. An expression for the super-posed effects may be derived from this table. (Effect of + q for T + ? T) + (Effect of - q for T + ?T-t,) + (Effect of + q for T + ? T - t,) + (Effect of - q for ? T) = Resultant........(2) The desired result is obtained by substituting the effect defined by Eq. 1 for the terms in Eq. 2. The result is Eq. 3. When the logarithmic approximation is made for the exponential integrals and the terms collected the result is Eq. 4. Let T — t2 = T = flowing time following short term shut-in t2 — t1 = 6 = duration of short term shut-in Then T - t1 = r + 6 Substitution of these quantities in Eq. 4 gives p(rw ?T) = P,, -When d<<t - AT then d—&apos;-, T— approaches 1. r + AT In this case the effect of the short term shut-in may be ignored. In order to get some idea of the numerical magnitudes involved take the worst possible case, when AT = 0, that is at shut-in. If the error is made less than some maximum acceptable value at this time, it will be less than the maximum for all subsequent times. d + r Let the difference between the value of y-— and 1 be less than 0.1. Then —6+r — 1 < 0.1 S < O.l T Therefore, if the flowing time following a short term shut-in is at least 10 times the duration of the short term shut-in, the error introduced by ignoring the short term shut-in will not exceed 10 per cent of T+AT A T

Jan 1, 1957

By R. M. Fowler, H. L. Hamner

DURING the last 25 years, there appeared in the literature a number of papers describing equipment and operating techniques for the determination of total oxygen in iron and steel. In the early papers, comparatively little attention was paid to side reactions that occur when iron is saturated with carbon at a high temperature in a high vacuum. As more experience was gained with the new method, the limitations appeared. Metals, with a boiling point lower than iron, distilled out of the crucible, condensed in the cooler part of the furnace, and subsequently reacted with carbon monoxide to form oxides and carbon. Aluminum, manganese, and the alkaline earth metals proved troublesome in this respect. Modifications have been devised to overcome the difficulties due to aluminum and manganese, while the alkaline earth metals are not of too much concern as yet to the steel chemist. The reactions of sulphur have received less attention, although it is generally recognized that some carbon disulphide is probably formed. Liquid air traps have been used in some cases to prevent any carbon disulphide from entering the analytical train. Sulphur was not a particular problem at the Union Carbide and Carbon Research Laboratories until the analysis of the irons of higher than usual sulphur contents became necessary. In order to describe the procedure developed for such irons, it will be necessary to first describe the type of vacuum-fusion equipment employed because the operation of vacuum-fusion equipment is an art to a considerable extent. At the Laboratories, vacuum-fusion equipment has been in daily operation since about 1930. Over the years, the evolution of this apparatus has been governed by the versatility required to analyze a wide variety of materials. Since all types of materials from high purity metals to slags are analyzed and, since seldom more than a few samples of one type are analyzed in succession, the apparatus was designed for accuracy and flexibility rather than for speed. A general view of the equipment is shown in Fig. 1, while Fig. 2 shows the relationship of the various parts. In Fig. 2, A is a vertical double-glazed 24X27/8 in. OD silica tube heated with a 20 kva mercury-arc high frequency generator. The tube is closed with a water-cooled brass head attached with de Khotinsky cement. A turret cap fits on this head and is sealed with a 1/8x3 in. "0" ring. The head contains a sight glass and two 8 in. horizontal glass tubes, for sample storage, cemented in with de Khotinsky cement. B is a four-stage Gaede mercury diffusion pump connected to the water-cooled head with a 11/2 in. copper tube through a flange with an "0" ring. The output of the vacuum pump feeds into an automatic Toepler F pump which compresses the gas sample over mercury in the measuring burettes, G and H. There are bypasses in this line for a McLeod gage C and a Piranni gage D, a manometer E, and for initial pumping out of the system with a Cenco Megavac backing-up pump. The reduction crucible shown in Fig. 3 is machined of Tungar Bulb quality (A.G.K.T.E.-2) graphite. The sample is guided into the crucible with the graphite funnel depicted on this figure. The arrangement of the crucible, radiation screens, etc. in the furnace is as follows: A 1 15/16x61/2 in. Alundum thimble, porosity RA-84, with two 1/8 in. holes near the top and opposite each other which take a pair of special tongs used for lowering it in place, is prepared. A 3/4 in. layer of powdered graphite is placed in this Alundum thimble, and the graphite crucible containing 20 g of ingot iron and 0.5 g of carbon is carefully centered on this bed of graphite powder and graphite powder is packed around it to the top of the graphite cru-

Jan 1, 1953

By S. Weinig, E. S. Machlin

IN a previous study of the grain boundary stress relaxation phenomenon,&apos; the authors had arrived at the conclusion that two successive steps were involved in the complete relaxation of stress at a grain boundary. These two steps were grain boundary migration and grain boundary slip. It was further suggested that the slower of these two processes is rate controlling. In an attempt to ascertain the validity of the above, a study of grain growth kinetics on the same alloys used for the previous study was undertaken. Separate wire specimens, 0.030 in. diam, in the same as-deformed state (99 pct reduction in area) as in the previous investigation were heated to the various temperatures for a sequence of times. The compositions used and the temperatures of testing are summarized in Table I. A statistical determination of grain size was then made on each specimen, using the average length of traverse between boundaries as a measure of the grain size. Examples of typical results obtained are shown in Figs. &apos;1 and 2. The grain growth law D = ktn was found to fit most of the data. Using this relation, values of the grain growth exponent n were calculated and the inter -esting dependence of n on solute content shown in Figs. 3 and 4 was then obtained. Also, it was found that the constant K which was obtained from extrapolation is roughly independent of solute content. (K is uncertain to within ±25 pct.) An estimate of the activation energy for grain growth was made using the technique of Burke? This method utilizes the plot of the reciprocal of time necessary for the grain size to increase from a definite starting size Do, to a final size D, for each isothermal heat treatment. The slope of this curve corresponds to the heat of activation for the process. In Fig. 5 the rate of grain growth is plotted against the reciprocal of absolute temperature. The activation energies were obtained from these curves and are summarized in Fig. 6. Discussion It is interesting to note that the same saturation in the variability with concentration has been found for the grain growth exponent n in this research as was found in the previous researches on both grain boundary stress relaxationa and internal friction of dislocation origin." The significant feature is that saturation in the variation of these properties has been found to occur at about the same level of solute concentration, namely, between 0.1 and 0.5 atomic pct. The only characteristic common to these different quantities is that solute adsorption at grain boundaries and dislocation can take place and affect these values in a similar fashion. Thus, it is concluded that the grain growth exponent n depends upon solute adsorption at the grain boundaries. It appears, therefore, that theoretical considerations leading to the contrary conclusions5,6 have not treated the real process by which solute atoms exert their effect on grain growth. Prior to the analysis of the observed activation energies, certain of the aspects of the aforementioned grain boundary stress relaxation investigation will be briefly reviewed. It was found that with the addition of solute atoms the grain boundary stress relaxation peak (internal friction vs temperature) decreased in intensity. Simultaneously a second peak was observed which increased with increasing solute atoms. Both of these peaks were shown to be the result of grain boundary stress relaxation. They have been termed, respectively, poire peak and solute peak. It was suggested that the solute peak was dependent upon grain boundary migration, whereas the pure peak was a manifestation of grain boundry slip. Activation energies for both peaks were obtained as a function of Solute content. The value of the activation energy in the temperature range corresponding to the solute peak was

Jan 1, 1958

By S. F. Frederick, W. A. Bailey

The relationship between microstructure and mechanical properties of cast 356-type aluminum alloys was studied to determine the cause of the variations in properties resulting from differences in solidification rate. It was found that variations in strength are a consequence of variations in ductility and that ductility is inversely proportional to the dendrite cell size. A mechanism is proposed to account for this correlation based on the fracture strain of the inter-dendritic silicon particles and the differential strain across dendrite cell boundaries. IT has long been assumed that permanent mold castings of aluminum are superior to sand castings because of their finer grain structure and reduced porosity.&apos; A systematic variation of static properties was noted during unpublished studies of fatigue-strength variations with solidification rate of A356-T6. Of particular interest was the observation that for a given composition and heat-treatment, both ductility and the ultimate strength increased with higher solidification rate. Because the A1-Si system forms the basis of many alloys used for castings and welding wire, a study was initiated to determine the details of how higher cooling rates improved mechanical properties of these alloys. The results of this study are presented here. EXPERIMENTAL PROCEDURE Specimens were prepared from 356-T6 to supplement the A365-T6 alloy data from earlier studies. This allowed a comparison of behavior of alloys with substantially different strengths but with only small differences in alloy composition. The composition and heat treatment of both alloys are given in Table I. The specimens were cut from a chill plate casting,&apos; which is a 6 by 9-in. plate, 1 in. thick, which has one end heavily chilled, and a large riser at the other so that solidification is essentially unidirectional from the chill end to the riser. Although not measured here, solidification times measured on similar specimens by embedded thermocouples are a few seconds at the chill end and up to 5 min near the riser. Specimens were obtained by cutting slabs from the plate, parallel to the chill; these represented different cooling rates, with essentially the same composition. For the tests, either 0.125 or 0.250-in. thick slabs were cut for standard 2-in. gage length specimens. The thicker specimens were tested to failure at 2000 lb per min while the thinner specimens were tested in an Instron machine at a constant cross-head speed of 0.02 in. per min. These thin specimens were intended for trans- mission electron microscopy. Some thin specimens were tested to failure while the remainder were given various amounts of prestrain. Dendrite cell sizes were measured by the linear intercept method on photomicrographs at either X100 or X50, depending on the cell size. It was assumed that the dendrite cells were outlined by the silicon particles. Determinations were made on two mutually perpendicular planes and an rms average taken. Electron fractographs of representative tensile specimens were made in the conventional manner using the two-stage replica technique.3 Samples for transmission electron microscopy were prepared by chemical milling followed by electropolishing. RESULTS AND DISCUSSION The results of the tensile tests and the dendrite cell-size determinations are given in Figs. 1 and 2. All data show the same trends, namely, a decrease in ultimate strength and elongation with increasing distance from the chill (and solidification time), and a corresponding increase in dendrite cell size. The yield strength remains essentially constant. The constancy of the yield strength was particularly significant since it indicated that variation in the solidification rate does not affect the stress required to initiate plastic flow. By plotting true stress-true strain curves as in Fig. 3, it can be seen that both

Jan 1, 1969

By J. Lindbo, B. Vigeholm

IN transmission electron microscopy, specimen thicknesses quoted are frequently based upon either traditionally familiar values or a few evaluations representing the whole material. Taking aluminum in 100 kv TEM as an example, average and maximum values are widely accepted as being 2000 to 2500 and 6000 to 7OOOÅ, respectively. It is the purpose of this note to revise these figures and to point out the importance of evaluating individual specimens carefully. All evaluations have been based upon slip trace widths and lattice orientations as determined from diffraction patterns. In many cases where two or more slip systems have been operating the geometrical method described by Crocker and Bevis1 has been applied as a check. The foils were usually oriented to within 2 deg from the exact Bragg angle. Kikuchi patterns were used as indications of correct orientations but not applied in the evaluations. The tilt of the foil surface relative to the beam normal may with certain geometrical relations between the tilt axis and the operating slip plane lead to substantial errors.2&apos;3 Where these geometries were inevitable the samples were omitted in the investigations. Various measures were taken in order to overcome ambiguities, e.g., comparison with neighboring grains, tilts, evaluations based upon two or three slip systems,&apos; and comparison with extinction contour evaluations where s = 0 conditions were obtained. Errors caused by misinterpretation of the slip traces on a micrograph are easily avoided by considering the bright-dark sequence on opposite surfaces and by taking into account the tapering of the foil usually leading to a distinguishable divergence of the pair of traces. In the investigations described here the interpretation was further facilitated as the slip trace formation was observed on the microscope screen and sketches taken down. In a few observations slipping was so violent that the distinction of pairs was considered dubious and consequently given up. To assess average values, thickness evaluations carried out in two independent investigations were analyzed: I) 99.998 pct A1 extruded, cold-drawn, and recrys-tallized to grain sizes between 35 and 500 um were deformed in tension at room temperature. In order to determine the dislocation densities as a function of strain,4 specimens prepared by spark machining and electropolishing in a PTFE holder were analyzed in the electron microscope at 100 kv. Thicknesses were evaluated for 569 selected areas. Histogram I in Fig. 1 shows the results, the average thickness being 4900Å. II) Electropolished specimens prepared from 99.9999 pct A1 with magnesium contents from 0.005 to 0.5 pct rolled to foil and annealed were subjected to fission fragment irradiationa2 For volumetric dose and defect concentration determinations thickness evaluations were performed on 123 areas. Histogram II in Fig. 1 shows the thicknesses of these areas averaging 4250Å. Whereas in investigation I no selection related to thickness has been made, some thin as well as thick areas have been omitted from I1 for experimental reasons. This and the application of two different microscopes although of the same type may account for the difference in average thickness. Assuming a mean error of 10 pct for a single evaluation, the error of the average should be negligible. In order to investigate the maximum transmissible foil thickness in aluminum, specimens were prepared from single crystals with (111) and (110) orientations parallel to the beam, and from polycrystalline material. Maximum values of thickness that could be measured were given by the stopping of the dislocations. The visibility often extended far beyond the end of the slip trace, but with no means of knowing the

Jan 1, 1970

By G. Derge, R. E. Grace

Diffusivity of bismuth in liquid Pb-Bi alloys has been measured by the capillary reservoir method as a function of temperature and composition. Fair agreement between theory and experiment is found for the measured diffusion coefficients and activation energies of diffusivity and viscosity in dilute lead alloys. The measured diffusion coefficients in the high bismuth alloys describe mass transport in special concentration gradients. THE study of diffusion in liquid metals has been restricted largely to the amalgams over small ranges of temperature and composition. In contrast to this, diffusion and transport of ions and molecules in aqueous and organic solvents have been studied extensively for the past 50 years. The general difficulty of measuring diffusion coefficients in both gases and liquids at high temperatures has been that of eliminating convection currents. Measuring techniques based on freezing and sectioning after the diffusion period1 are not particularly satisfactory because of the volume changes and segregation which occur during freezing. The most promising technique which is currently being developed for liquid metals is the capillary reservoir method. This eliminates convection currents from the diffusion zone and requires measurements only of the length and initial and final compositions of the alloy within the capillary. Anderson and Saddington&apos; have measured the diffusion coefficient of tungstate anions in aqueous Na,W04; Wane4&apos; and Hoffman- ave studied structure and self-diffusion in water and self-diffusion in mercury, respectively, by similar techniques. Selection of the Pb-Bi system for initial study was made for several reasons: I—It afforded a low temperature system for development of techniques which would be suitable for high temperature measurements in liquid iron. This research on diffusion in liquid iron is now in progress as a part of a general program on the rates and mechanisms of slag-metal reactions. 2—Activity data on liquid Pb-Bi alloys of all compositions are available from the emf meas- urements of Strickler and Seltz.9 3—Some data are available on the diffusion of bismuth into solid lead. The measurements on solid alloys were made by von Hevesy and Seith7 for the concentration range of 0 to 2 pct Bi. An appropriate solution to Fick&apos;s law (unsteady state) for the capillary reservoir has been found by considering the mass flow which passes through a unit area of surface on a slab of infinite thickness as a function of time. This is the first application of this solution to diffusion measurements, although a similar solution is available for identical boundary conditions.&apos; By analogy with heat conduction, the problem reduces to a perfectly insulated infinite slab at temperature C,, one surface of which is quenched to C, for all times, t. Heat is permitted to flow from quenched surface of the slab to an infinite supply of coolant at C.&apos; (see Appendix). For the corresponding solution for diffusion in liquids, these terms become Where Cu is the initial concentration of component A" in entire capillary at t - 0, C, is the final con- In this case. component A is bismuth, and C, = 0. centration of component A in entire capillary at t = t, C, is the concentration of component A in bath for all t, 1 is the length of the capillary in centimeters, t is the time of diffusion period in seconds, and D is the diffusion coefficient in square centimeters per second. By comparison with solutions to Fick&apos;s law used in the solid state, this solution for liquids is similar to the Grube solution for solids, where the change in D with chemical composition is not taken into consideration. Difficulty is to be expected if large concentration gradients are employed and if the concentration gradients extend over an appreciable length of the capillary.

Jan 1, 1956

By R. F. Mitchell, G. F. Dillon, A. F. Armington

In this paper the present methods of boron preparation are discussed with emphasis on the iodide intermediate. Several methods of boron triiodide preparation were investigated, the most satisfactory method being the preparation from the elements. A yield of 60 pct based on iodine is found for this method. Zone-refining, sublinzation, distillation, and fractional-recrystallization results are given for the boron triiodide, with distillation producing the best results. Several methods of decomposition are also discussed. The purity of the resulting iodide boron approximates the puritjl of the best available bromide boron, ELEMENTAL boron has been suggested as a possible high-temperature semiconductor by several workers,&apos; but has never been exploited as a device material. The principal difficulty with boron is the unavailability of pure crystalline material from which accurate information on electrical properties could be obtained. Most boron crystals presently produced are very imperfect in structure and of questionable purity, particularly in relation to carbon content. Several methods of boron purification have been reported in the past few years, all of which produce material with a purity better than 99.0 pct. Most of these methods have been the subject of a recent review by Starks&apos; and will not be elaborated upon in this report. However, of all the purification methods reported, only those using halide intermediates produce a purity approaching that usually required for electronic applications. The bromide intermediate has been most used for the preparation of high-purity boron.&apos;y3 This material is easily prepared from the elements and can be effectively purified by distillation and decomposed by hydrogen reduction. The resulting product contains a trace of silicon, and an uncertain amount of carbon, believed to be approximately 100 ppm. It has been recently reported by Russian workers that high-purity boron can be produced using an iodide intermediate.&apos; In the work cited, boron is reported free of spectro-scopically determined impurities, but the reported detection limits are quite high (- 100 ppm). In addition, no data is given on the carbon content of the product. In the present paper, boron triiodide was chosen as the intermediate for several reasons. First, carbon tetraiodide, which could be a major impurity, is reported to be unstable above 200" and hence could be easily separated from the boron triiodide by its decomposition, since temperatures greater than this are attained during the purification process. The low melting point (45°C) and boiling point (20B°C) and the relatively high vapor pressure of boron triiodide should allow the application of any physical purification technique to the material. The possibility of a lower decomposition temperature than that used for the bromide process is another advantage which might cut down extraneous contamination. The iodide, however, does have certain disadvantages when compared with the bromide, the production cost being the most significant. This is the result of a higher halide-to-boron weight ratio, which means more intermediate must be employed. The cost of the starting material is also greater for the iodide. This cost could be considerably reduced however, by recycling the iodine byproduct. Epitaxial growth of boron, which is probably the best method of producing junctions, should be possible with either the bromide or the iodide as the intermediate. However, this has been attempted only on a limited scale up to the present time because of the unavailability of good crystals. The authors have been relatively successful in laying down a heterotaxy of boron on silicon, however. This will be reported at a later date. Several crystalline modifications have been reported for boron, four of which are now believed to be real.&apos; These are the a! and 0 rhombohedral and the a, and 0 tetragonal. In general, the a! rhombohedral is the low-temperature form and the B rhombohedral is the high-temperature form. The tetragonal structures are detected between 1000"

Jan 1, 1964

By S. S. Lisnyak, B. D. Lichter

An important question in the study of the "hot corrosion" phenomenon (i.e., accelerated oxidation of Ni-Cr-base and Co-Cr-base "superalloys" in the presence of sulfur) is the condition of formation and physico-chemical properties of different sulfides in the system Ni-Co-Cr-S. seyboltl has observed the presence of ((chromium-rich" sulfides of compositions M3S4, and M2S3 in the scales of superalloys after hot corrosion; however, as he points out, much confusion exists as to the identity of sulfides found on Ni-Cr and Co-Cr alloys. According to the literature,&apos; ternary sulfides, e.g., NiCr2S4, (monoclinic structure) and CoCr2S4 (spinel structure) exist in these systems. Therefore, it is likely that these compounds are found in the scale of alloys undergoing hot corrosion. At present this possibility has not been discussed in the literature. Accordingly, we have begun investigation on the properties of ternary sulfides and their mutual interaction. The magnetic and electrical properties of pure NiCr2S4 and pure CoCr2S2 have been previously determined."-&apos; In the present work we have studied the interaction between these sulfides at high temperatures by means of X-ray diffraction and magnetic susceptibility. The measurements were carried out at room temperature after appropriate thermai treatment of samples at high temperatures. For alloys containing the three elements nickel, chromium, and cobalt this interaction may be of importance in the study of the hot corrosion phenomenon. The compounds NiCr2S4 and CoCr2S4 were prepared from stoichiometric amounts of the elements and CoS in the case of CoCr2S4. Samples were mixed and sealed in evacuated silica tubes, slowly heated to 900&apos; to 100O°C, and held at temperature for a total of 120 hr (NiCr2S4) or 80 hr (CoCr2S4) with intermediate re-grinding~. X-ray diffraction showed a pure spinel structure for CoCr2S4 and a monoclinic structure for NiCr2S4. Samples of mixtures of the two ternary sulfides were prepared with different compositions, see Table I. Samples were heated for a total of 80 hr at 900&apos;C in evacuated silica tubes, with one intermediate regrind-ing. The capsules were slow-cooled to room temperature in the furnace. Samples for X-ray diffraction were prepared by placing powder on a glass slide with vaseline. Dif- fractometer traces were obtained on a G.E. XRD-5 diffractometer using a chromium tube and vanadium filter (40 kv and 31 ma). The size of the spinel unit cell was determined from the eight highest angle peaks (80 deg < 2b < 160 deg). Calculated lattice parameters were plotted vs cos B . ctn 0 and extrapolated to 6 = 90 deg. Measurements of the magnetic susceptibility were carried out at room temperature using the Faraday method in a magnetic field of 3000 G and using a Cahn RG automatic microbalance. The system was calibrated from the well-established susceptibilities of platinum and palladium: (Xpt = 0.968 x 10-6 g-1 and Xpd 7 5.04 x 10~6 g-1). The weight of samples were approximately 0.200 g. X-ray diffraction patterns for unsintered mixtures showed Bragg peaks from both the spinel (CoCr2S4) and monoclinic (NiCr2S4) structures. After sintering no monoclinic peaks were observed in samples containing up to 40 mol pct NiCr2S4. However, the spinel peaks were displaced to higher angles with increasing

Jan 1, 1970

By R. I. Jaff, H. R. Ogden, D. J. Maykuth

A phase diagram for alloys containing from 0 to 66.9 pct Mn was determined. Two compounds, tentatively labeled 6 and y, were found in this range. The 6 compound is located at about 66.9 pct Mn and melts congruently at 1330°C. The ? compound has a composition near 53 pct Mn and originates in a peritectic reaction at 1200°C between liquid and 6. ß and Y enter into a eutectic reaction at 1175°C. The ß phase field terminates in a very sluggish eutectoid reaction between a and ? at 550°C. MANGANESE is one of the important alloying addition elements to titanium. As a ß-stabiliz-ing addition for a-ß and ß alloys, it provides high strength with adequate ductility.&apos; Two of the earliest commercial alloys contain manganese as a major alloying component.&apos; The earliest published data on the constitution of Ti-Mn alloys was that of Wallbaum,~ who reported the existence of the compound TiMn2. The transformation range of commercial-purity Ti-Mn alloys was investigated by Craighead, Simmons, and Eastwood&apos; who found limited a solubility and a lowering of the ß transus to about 790°C at 7 pct Mn. Preliminary work by the authors of this paper, using high-purity titanium, confirmed the ß-stabilizing action of manganese and showed the existence of several intermediate phases in the Ti-Mn system." More recently, McQuillan3 determined the ß transus temperatures for high-purity Ti-base alloys containing up through 4.4 pct Mn. These data are given in Fig. 1. The present investigation covered alloys made with a high-purity base. The constitution of titanium-rich alloys made with commercial titanium has been reported4," by Holladay, Kura, and Jackson. The alloy range covered in the present investigation was from 0 to 69.5 pct Mn. This alloy range extends slightly beyond the composition of the first congruent-melting compound encountered on proceeding from the titanium end of the system. A description of the materials and methods used in the determination of the diagram is given in the Appendix. The partial phase diagram determined for the Ti-Mn system is shown in Fig. 2. Details on equilibria in the titanium-rich alloys are given in Fig. 3. Liquid-Solid Relationships Observations on the cast structures of the arc-melted ingots showed that the terminal solid solution of manganese in ß titanium enters into a eutectic reaction with an intermetallic compound labeled ?. As will be shown later, this compound has a composition around 53 pct Mn. The eutectic reaction temperature was determined as 1175°C by thermal analysis which also showed that the ? phase originates in a peritectic reaction at 1200°C. Fig. 4 shows typical eutectic structures for alloy compositions on both sides of the eutectic composition which is located at 42.5 pct Mn. In alloys over the range of 45.4 through 69.5 pct Mn, a second intermetallic compound, labeled 6, was identifield as the primary phase. This phase consistently increased in amount as the manganese content approached 66.9 pct, and, as shown in Fig. 5, an alloy structure containing 66.9 pct Mn consisted essentially of the 6 compound. Thermal-analysis data indicate a melting point of about 1330°C for the 6 intermediate phase. At 67.0 pct Mn, small quantities of a new, higher manganese-content phase were observed in the form of Chinese-script eutectic particles. Comparison of Fig. 6a and b shows an increasing quantity of this phase as the composition was increased to 69.5 pct Mn. The formation of peritectic ? in arc-melted alloys containing 45.4 pct Mn and above appears to be almost entirely suppressed, as shown in Fig. 7a and b. This is because of the narrow freezing range available for its formation by peritectic reaction and because of the very high cooling rates obtained in

Jan 1, 1954

By Paul Gordon

The distribution coefficient, k, of interest in zone refining is generally defined as the ratio of the solid to the liquid solubilities of one element in another at the normal melting point of the solvent. In practice, distribution coefficients are frequently calculated from solubilities at temperatures well below the melting point of the solvent, e.g., at a eutectic temperature. This is done because of the general lack of accurate data on the liquidus and solidus curves in most phase diagrams. The practice is equivalent to assuming that the liquidus and solidus curves are straight lines in the temperature range between the melting point of the solvent and the temperature at which data for the solubilities are known. It is recognized that the k values so derived may be in serious error; we have found evidence in recent zone-refining operations that a case in point is silicon in aluminum. The phase diagram found in the literature for silicon in aluminum indicates a eutectic on the aluminum-rich side at 12.5 at. pct Si and at 577°C,1 and a solid solubility of silicon in aluminum at this temperature of 1.59 pct.2 It also shows the liquidus and solidus as nearly straight lines from 577°C to the melting point of aluminum (660°C)1,2 The k value obtained from this data is 0.13. This is almost exactly the same as the k value (about 0.14)&apos; obtained in a similar way for copper in aluminum. Yet we have found by mass-spectrograph analyses* of three bars of zone-refined aluminum that copper is efficiently removed from aluminum by zone refining but silicon is not. Two of the three bars of aluminum were zone-refined in our laboratories, the other in the laboratories of AIAG Metals, Inc. The former two bars, designated bars PG2 and PG3, were 30 in. long by 1 in. in diameter during refining; each was processed in a high-purity graphite boat* and kept under refining stage of the process consisted of thirty unidirectional zone traverses at rates of about 1 to 2 in. per hr, with a zone length of 1 to 2 in. At approximately the middle of the refining period a 6-in. piece of the impurity-laden finishing end of the bar* was cut off and replaced with new start- ing material. Following refining, the purest 20-in. section of the bar (obtained by discarding approximately 2 in. of the starting end and 8 in. of the finishing end of the bar) was leveled and then analyzed. The AIAG bar was 16 in. long and about 1.2 in. in diameter; it was purified by eight passes of a 2-in. zone at a rate of 1.6 in. per hr, the bar being contained in a sintered alumina boat lined with loose alumina powder of the highest purity. Data for the silicon and copper contents of the three refined bars are given in Table I. Derived data for the efficiencies of the zone-refining operations are listed in Table 11. It is clear from these two tables that the copper is removed much more efficiently—by a factor of 10 to 50 times—from aluminum during zone refining than is silicon. For example, in bar PG3 the thirty zone passes reduced the copper content from 10 to 0.02 ppm, i.e., by 500 times, whereas the same treatment lowered the silicon content by only a factor of about 16. It seem virtually certain, therefore, that the distribution co efficient, k, for silicon in aluminum is well above that for copper and is very likely not much below unity. This also implies that the solidus line on the aluminum-rich side of the A1-Si phase diagram is very probably appreciably curved near the aluminum melting point since the phase-diagram data indicate such curvature is unlikely in the liquidus.

Jan 1, 1965

By Nicholas J. Grant, Olaf Troili, John Chipman

IN recent studies of the factors which affect the rate of desulphurization and its equilibrium, it became apparent that certain concurrent reactions were operative which had a significant effect on desulphurization. This is emphasized in the experiments of Hatch and Chipman1 and of Grant, Kalling, and Chipman&apos; by the slow approach to a final state of equilibrium which is in marked contrast to the initial rapid transfer of sulphur from metal to slag. Since the removal of sulphur is of such profound importance in iron and steelmaking, it appeared necessary to investigate the reactions responsible for this behavior. It is now known that the presence of iron oxide in the slag interferes seriously with the principal reaction of blast-furnace desulphurization: CaO (slag) +-S + C - CaS (slag) + CO [l] The interfering reaction is most simply expressed as: CaS (slag) + 0 = CaO (slag) +-S 121 and a small concentration of oxygen (or FeO) is sufficient to hold a considerable amount of sulphur in the metal. It has been shown by Grant, Kalling, and Chipman2 that the addition of MnO to blast-furnace slag slows the removal of sulphur from the metal. This effect overshadows the contribution of MnO to basicity and is ascribed to its oxidizing power. It will be shown in this paper that SiO, also has sufficient oxidizing power to interfere with blastfurnace desulphurization. This is, of course, only one of its several effects. Primarily it is an acid and therefore reduces the concentration of excess lime. But when silicon is reduced to the metal the oxygen to which it was previously bonded becomes in part available for reaction 2. The proof of this statement is found in the following experiments. Experimental Procedure and Results Utilizing the same procedure and apparatus described by Grant, Kalling, and Chipman&apos; five additional heats were made using slags IV and 11, the starting compositions of which were: slag IV—40 CaO, 10 MgO, 35 SiO,, 15 A1,0,; and slag 11—50 CaO, 10 MgO, 25 SiO,, 15 Al3O3. An important difference between these heats and those previously reported was that silicon to the extent of 1 to 4 pct was added to the present heats whereas the starting silicon content was formerly about 0.2 pct. Table I shows the slag and metal analyses for heats 82 to 87, and Table I1 shows the silicon addi- tions made to the charge. These additions are based on 400 g of metal and 400 g of slag. All heats had 1.65 400pct S charged before the cold slagadditions. The temperature was maintained at 1525°C. Rate of SiO, Reduction: Fig. 1 shows the silicon content of the metal in contact with slag IV at 1525°C as a function of time. Heat 70 from the work of Grant, afunctionKalling,of and Chipman is included as the lowest starting silicon. It will be noted that eeven with 4 pct Si in the starting metal, there is an increase in silicon content with time. Heat 84 is apparently approaching silicon equilibrium very slowly. Heats 70 and 82 with very much lower slowly.starting silicon show a more rapid initial rise in startingsilicon content but do not reach equilibrium during a long holding period. Fig. 2 shows 3 different initial silicon contents for Fig.2shows3differentheats 73 (from Grant, Kalling, and Chipman) 86 and 87, in contact with slag II, the most basic slag. Heat 73 is increasing in silicon with time, whereas heat 87 with an initial silicon content of 3.7 pct shows a decrease with time. Heat 86 shows a very close approach to equilibrium. The rate of transfer of silicon from slag to equilibrium.metal is very slow in all of those heats, even those which are initially far from equilibrium. ____

Jan 1, 1952

By W. R. Hibbard

It has been proposed1 on the basis of slip and flow that the ideal deformation texture of drawn wire for face-centered cubic metals is a (111) direction parallel to the wire axis. Under these considerations, an intermediate [loo] texture is permissible but should eventually change to the stable [Ill] orientation. This theory does not explain why copper and its alloys containing up to about 30 pct nickel, 5 pct zinc and 1 pct aluminum were found to have a double [Ill], [100] texture, while alloys with at least 8 pct zinc and 2 pct aluminum developed essentially a single [Ill] texture.1,2 It does suggest, however, that the [loo] component of the former alloys should disappear with additional deformation.3 Some evidence exists to support this suggestion. Howald4 reported that annealed copper wire previously drawn 93.8 pct and 98.5 pct developed a single [Ill] texture. Since, in wire, the drawn and annealed textures are similar, these wires probably had a single [Ill] deformation texture before annealing. In addition, although cold rolled polycrystalline copper and 80-20 brass were found to form different types of pole figures,5,6 single crystals of these metals when rolled from the stable (110) [112] orientation were found to produce essentially the same polo figure.7.8 It may be, therefore, that while the addition of solute elements changes the path by which the final texture is obtained, the final texture is not changed. Experimental Results The wires remaining from the previous investigation1 already drawn about 50 pct reduction in diameter were further drawn to 86 pct and then to 96.4 pct total reduction in diameter. The textures were determined after these stages by transmission X ray photograms taken with a copper K-alpha beam rotated 0 degrees toward the wire axis. It was found that the ratio of the [111].] and [100] intensities of the double texture in copper and its alloys containing 0.94 pct aluminum, 30.70 pct nickel, 2.61 pct zinc and 4.99 pct zinc increased from about 3:l for the 50 pct reduction to about 9:l for the 86 pct reduction. After 96.4 pct reduction, these wires exhibited essentially a single [lll] texture. Summary Thus, the drawn wire deformation texture of copper and its alpha solid solution alloys containing aluminum, nickel or zinc is essentially a single [Ill] texture as predicted by theoretical considerations of slip and flow.&apos; For copper and its alloys containing up to about 1 pct aluminum, 5 pct zinc and at least 30 pct nickel, an intermediate [loo] component is found after about 50 pct reduction in diameter, but disappears after about 95 pct reduction in diameter. For alpha solid solution alloys containing at least about 2 pct aluminum and 8 pct zinc the single [Ill] texture is developed considerably more easily and is found after about 50 pct reduction in diameter. No explanation of this compositional effect is apparent. Similar work is contemplated for cold rolled and cold compressed alloys. References 1. w. R. Hibbard, Jr. and M. K. Yen: Trans. AIME 175, 126. Metals Tech., Feb. 1948, TP 2334. 2. W. R. Hibbard, Jr. and D. E. Trout, 11: Trans. AIME 185, 620. Jnl. of Melals, Sept. 1949, TN 18. 3. W. R. Hibbard. Jr.: Disc. of R. M. Brick&apos;s paper on Deformation Textures, ASM Symp. on Cold Working of Metals, Oct. 1948. 4. T. S. Howald: Disc. of Ref. 1. Trans. AIME, 175, 126. Melals Tech. Aug. 1948, TP 2449. 5. R. M. Brick, D. L. Martin and R. P. Angier: Trans. ASM (1943) 31, 675. 6. 0. Dahl and F. Pawlek: Zlsch. Melall. (1936) 28, 266. 7. C. S. Barrett and F. W. Steadman: Trans. AIME (1942) 147, 57. 8. J. E. Burke and C. S. Barrett: Trans. AIME 175, 106. Melals Tech., Feb. 1948. TP 2327.

Jan 1, 1950

By Robert F. Mehl

PROGRESS in the general field of nonferrous physical metallurgy during the past .year has been uneventful but healthy. A continued increase is apparent in the number of useful alloys and in the mechanical treatment and heat- treatment of finished metals and alloys nothing can hinder the multiplication of alloys or the diversification of their treatment as knowledge of the behavior of .alloys increases; as ternary and quaternary alloys are better understood, hundreds of new metal combinations with unusual properties may well be expected. Evidence of rapid progress is already at hand.

Jan 1, 1936

By Charles E. Heinrichs

IN the last decade one of our oldest and largest non-metallic metallic mineral industries has been the subject of persistent technical research, the results of which are another example of the benefits following the systematic application of scientific principles. The consequent improvement in the technique of phosphate recovery represents the greatest material advance in the industry since the discovery of phosphate in Florida in 1881. Moreover, these successes have stimulated interest and development in numerous other nonmetallic industries. Strange as it may seem, and despite the fact that the phosphate deposits of Giles County, Tennessee, together with those of Polk and Hillsborough Counties, Florida, have yielded more than 50,000,000 long tons in the last twenty years, the mineralogy of phosphates has been given scarcely any space in our technical literature. For many years it was the general consensus that these so-called phosphate rocks represented a physical mixture composed principally of tri-calcium phosphate, together with smaller quantities of calcium carbonate, calcium fluoride, iron phosphate, aluminum phosphate and other less important constituents. More recent investigations, however, led to the conclusion that these phosphates really represent a complex mineral in which calcium, iron, aluminum, phosphorus pentoxide, carbon dioxide, and fluorine all form a definite part of the molecule. Colony, after a careful study, utilizing chemical, microscopic, and X-ray diffraction methods, reported that American phosphates consist principally of calcium-carbono-phosphate of the staffalite type.

Jan 1, 1933

By Henry D. Hibbard

THIS article aims to clarify the use of some terms often occurring in writings on iron and -steel, and also to suggest several new short abbreviated names for some of the things related to the subject which now are indicated by phrases. Crude or Crude Iron The name crude or crude iron is recommended for the iron produced from ore by the blast furnace. When necessary it can be specified as pig iron when in the form of pigs (usually cold), or as molten iron, commonly called hot metal to distinguish it from cold iron in pigs. The product of a direct process of making wrought or malleable iron from ore is not included.

Jan 1, 1924

By Raymond O. Ladoo

FUSED quartz is a glass made by the fusion of nearly pure silica. Some confusion in terminology exists but in the trade today "fused quartz" generally refers to the perfectly transparent colorless product made from rock crystal whereas "fused silica" is a white, translucent product made from silica sand. Vitrified silica is the term preferred by purists for all quartz glass, but it lacks the definiteness of -the trade terms. Since the raw materials, methods of production, and properties of the finished products arc different for the two types, the trade terms are preferred. As fused quartz is amorphous, it-physical properties differ greatly from those of quartz crystal. Lacking crystallographic directions and having no piezo-electric properties, fused quartz. of course, has no value for the making of radio oscillator plates; but it does have other valuable and unique properties. Perhaps the &apos;best known and most useful properties are its extremely low coefficient of expansion and its ability to transmit short-wave ultraviolet radiant energy. Crystal quartz not only has an aver-

Jan 1, 1947

By AMY F. JENNINGS

TO give a concise history of the Woman&apos;s Auxiliary of the A. I. M. E. is a difficult task and much interesting information must needs be omitted. The organization has grown and evolved so much from its early simple beginning that it seems best to adopt the technique of some of our modern novelists and begin with the latest development. As the headquarters of the A. I. M. E. is in New York, it follows that the Woman&apos;s Auxiliary to the A. I. M. E. necessarily has also its central office and government there. The affairs of the organization are administered by a duly-elected president and five vice- presidents, a treasurer, recording secretary, and corresponding secretary and a board of directors, the personnel of which includes each chairman of a section or an elected or nominated representative who is able to attend the monthly meetings of the board and correspond with the section for which she acts, and the chairmen of the five standing national committees, i. e. Educational Fund, Library, Emergency, Membership and Hospitality. The chairmen of these committees are all responsible to the president and board of directors and their activities must be indorsed with their approval.

Jan 1, 1929

By AIME AIME

THE non-ferrous &apos;metals industry of the Soviet Union found itself in a very low position at the beginning of the reconstruction period in 1922, due to the absence of modern smelters and the run-down condition of the existing ones. Up to. 1924 there was no great demand for newly smelted non-ferrous metals due to the considerable stocks&apos; of copper, zinc, lead, tin and aluminum in the courtry and also to the undeveloped condition of Soviet industries. However, in 1925 it became necessary to obtain new stocks of non-ferrous metals and in that year 12,000 tons of zinc, 14,000 tons of lead and 2,000 tons of tin and aluminum were imported into the U. S. S. R.

Jan 1, 1929

By Carl S. Westerberg

Coal preparation practice and trends follow, among other factors, production trends in any given area. Considering an area the size of a state, some broad predictions may be made after a review of the annual production records. As this paper is concerned with coal cleaning in Utah, data on its production record are pertinent. Table 1 shows the percentage relation of coal production in Utah to the national total as a single figure up to 1935 which includes all recorded production. From 1935 through 1947 these data are presented by years. It is evident from these data that the production of Utah coal is ascending. The reason for this trend is industrial growth in the West resulting in a population shift which accounts for more people than the normal increase would supply together with Utah&apos;s relatively fortunate geographical location and its abundance of good-quality coal. Utah is also hopeful of supplying more coal in the future for West Coast power generati0n.l

Jan 1, 1949

By H. Reginald Hardy, Y. S. Kim

Recent studies of inelastic behavior and acoustic emission in geologic materials further validate the concept that such materials may be considered to consist of an elastic media containing an array of pores and cracks. In the present paper this concept is investigated further by experiments in which the mechanical behavior of a number of geologic materials were studied in detail at low stress levels using ultrasonic pulse methods. Experiments were carried out on cylindrical test specimens of Indiana Limestone, Tennessee Sand- stone and Barre Granite under relatively low confining pressures (0-5000 psi). Analysis of data from these experiments indicated that there existed a low-level critical stress at which there appeared to be a transition in the mechanical behavior of the material. Under triaxial stress, results indicated that the differential critical stress was relatively independent of confining pressure, i.e., the mechanism responsible for the transition in mechanical behavior was governed by a maximum shear stress criteria.

Jan 1, 1971