Search Documents

By H. H. Reamer, B. H. Sage

Attempts have been made to predict the volumetric and phase behavior of naturally occurring hydrocarbon mix-turesl-6 but these methods have not been extended to the higher pressures and tem-peratures that are currently encountered in some producing formations. Furthermore, the methods of prediction at present avail-able have not been tested in a sufficient number of cases to ensure their applica-bility to all naturally occurring hydrocar-bon mixtures, even at the lower pressures and temperatures. For these reasons the behavior of a number of hydrocarbon mix-tures from a field in which the subsurface pressures are above 4500 lb. per sq. in.t and the temperatures are in the neighbor-hood of 250°F. was investigated. Method The objective of this program was to determine the volumetric behavior of ma-terial as it existed in the reservoir as a function of pressure, temperature and com-position. Strictly speaking, this cannot be accomplished in any simple fashion. How- ever, the variations in composition that are encountered within a producing reservoir may be approximated roughly by means of mixtures made up of two arbitrarily chosen constituents. Experience indicates that the liquid and gas phases from a high-pressure gas trap afford a simple source of material for this purpose. Throughout this discus-sion the samples of the gas phase and liquid phase from the production trap will be called the "trap-gas sample" and the "trap-liquid sample," respectively. The volumetric behavior of both of the trap samples was determined throughout the temperature interval between 100" and 250°F. at pressures up to 5000 lb. per sq. in. In addition, the behavior of eight different mixtures containing varying proportions of the two trap samples was studied throughout the same temperature and pressure intervals. The experimental results yielded information concerning the specific volume of the material as a function of pressure, temperature and the relative quantity of the trap samples. The relative amount of each of the paraffin hydrocarbons of lower molecular weight than n-hexane was determined for each of the trap samples. In addition, the specific weight, viscosity and average molecular weight of the hexanes-and-heavier fraction of the trap-liquid sample were determined as well as similar information for each of five fractions separated from this material by distillation. From these data the weight fractions of each of the components from methane through pentane were determined for the trap samples and eight systematically chosen mixtures. Materials The gas and liquid samples were obtained from the production trap of a well in the Rio Bravo field in California during the fall of 1939. Information concerning the condi- 70

Jan 1, 1941

By Jack R. Elenbaas, Donald L. Katz

A radial turbulent flow formula has been developed which permits the computation of the pressure drop for radial flow in gas wells whether the flow is laminar, turbulent, or partially laminar and partially turbulent. Using the formula a complete back-pressure curve has been calculated and analyzed by a comparison with existing back-pressure curves. A procedure is presented for computing the permeability of the porous media when the porosity, sphericity and average particle diameter are known. Introduction Recent studies on the flow of fluids through porous media have provided new methods for computing flow under turbulent conditions. The present study was initiated as an investigation of pressure -drop computations for flow through porous sands in gas wells and as an analysis of present-day back-pressure tests. Although laminar flow exists in the producing formation of gas wells under normal flow rates, turbulent flow does take place adjacent to the well bore. As the flow rate is increased, turbulent flow exists further and further into the producing formation and under open-flow conditions in relatively deep wells a considerable portion of the flow through the sand will be turbulent. In order to calculate a complete backpressure curve for relatively deep wells without resorting to extrapolation of curves drawn from data obtained in back-pressure tests or calculations made in the completely laminar region, it was necessary to have some means of calculating pressure drop for flow through porous sands under turbulent conditions.4.6 As a result, a radial turbulent flow formula was derived from the equations recently presented by Brownell and Katz.1 A rigorous solution of this equation involves a trial and error graphical integration. By making the assumptions of average viscosity, temperature and compressibility factor of the flowing gas, it was possible to graphically integrate the relation for the general case of radial flow of gases through the porous sand of gas wells. A chart has been prepared relating the value of the integral to the radius of the well bore and to the Reynolds number of the flowing gas. The chart actually performs the graphical integration and the solution of the formula is then reduced to a simple trial and error calculation. A typical back-pressure curve is calculated to show the transition from laminar to turbulent flow. This paper will briefly describe the pro-cedurcs for computing flow through porous media, including a method for predicting sand permeability from porosity and grain size and shape. Flow through Porous Media Brownell and Katzl recently reported a correlation for computing flow of fluids through porous media by the use of an enlarged Reynolds number and friction factor in which the porosity of the bed is included as an additional prime variable. The enlargcd Reynolds number com-

Jan 1, 1948

By Donald L. Katz, Jack R. Elenbaas

A radial turbulent flow formula has been developed which permits the computation of the pressure drop for radial flow in gas wells whether the flow is laminar, turbulent, or partially laminar and partially turbulent. Using the formula a complete back-pressure curve has been calculated and analyzed by a comparison with existing back-pressure curves. A procedure is presented for computing the permeability of the porous media when the porosity, sphericity and average particle diameter are known. Introduction Recent studies on the flow of fluids through porous media have provided new methods for computing flow under turbulent conditions. The present study was initiated as an investigation of pressure -drop computations for flow through porous sands in gas wells and as an analysis of present-day back-pressure tests. Although laminar flow exists in the producing formation of gas wells under normal flow rates, turbulent flow does take place adjacent to the well bore. As the flow rate is increased, turbulent flow exists further and further into the producing formation and under open-flow conditions in relatively deep wells a considerable portion of the flow through the sand will be turbulent. In order to calculate a complete backpressure curve for relatively deep wells without resorting to extrapolation of curves drawn from data obtained in back-pressure tests or calculations made in the completely laminar region, it was necessary to have some means of calculating pressure drop for flow through porous sands under turbulent conditions.4.6 As a result, a radial turbulent flow formula was derived from the equations recently presented by Brownell and Katz.1 A rigorous solution of this equation involves a trial and error graphical integration. By making the assumptions of average viscosity, temperature and compressibility factor of the flowing gas, it was possible to graphically integrate the relation for the general case of radial flow of gases through the porous sand of gas wells. A chart has been prepared relating the value of the integral to the radius of the well bore and to the Reynolds number of the flowing gas. The chart actually performs the graphical integration and the solution of the formula is then reduced to a simple trial and error calculation. A typical back-pressure curve is calculated to show the transition from laminar to turbulent flow. This paper will briefly describe the pro-cedurcs for computing flow through porous media, including a method for predicting sand permeability from porosity and grain size and shape. Flow through Porous Media Brownell and Katzl recently reported a correlation for computing flow of fluids through porous media by the use of an enlarged Reynolds number and friction factor in which the porosity of the bed is included as an additional prime variable. The enlargcd Reynolds number com-

Jan 1, 1948

By George F. Weaton, Carleton C. Long, H. I. Najarian

Partial descriptions of the operation of the St. Joseph Lead Company's Joseph-town smelter have been published. In, 1936 the electrothermic production of zinc oxide was described;' in 1939 appeared a description2 of the electrothermic method of producing zinc metal. Inasmuch as the plant capacity has more than doubled, and in view of the fact that operating practices have improved greatly since these publications, it seems worth while to prepare a fresh description of the present-day elec-trothermic zinc plant and practice. Josephtown smelter is situated on the south side of the Ohio River about 3 miles below its confluence with the Beaver River. In addition to river barge, the smelter is served by Pennsylvania state highway No. 18 and by a spur line of the Pittsburgh and Lake Erie Railroad (N.Y.C.). A recent extension of this spur line connects with the Pennsylvania Railroad. As originally contemplated the plant was to handle only the product of the com-pany's own mines in St. Lawrence County, New york, but owing to the incessant demand for zinc and zinc oxide, it has been necessary to supplement New York concentrates with foreign ores (principally from Quebcc and the Argentine). The general operational procedure followed comprises roasting the sulphide con-centrates, converting the sulphur dioxide into sulphuric acid, preparation of a strong-structure sinter from the calcine, crushing &lid sizing of coke, reduction of coke-sinter mixture by electrothermic means, condensation of the evolved zinc vapor to make zinc metal or burning of the zinc vapor to make zinc oxide, collection and packing of the zinc oxide. Dusts recovered by the roaster and sinter Cottrells are treated in the leach plant for separation of lead sulphate, cadmium metal and zinc sulphate. The general flowsheet is shown in Fig. I. Principal Items OF Equipment Roaster Plant Concentrate drier, 6-ft. 'ia. by 4O ft. 5 in., countercurrent, direct gas-fired. 3500-~on concentrate storage in three vertical steel tanks. Five modified Nichols-Herreshoff twelve-hearth roasters, 21 ft. 6 in. in diameter. Four fans for shaft-cooling air. One threedrum Stirling water-tube waste-heat boiler, 4'8 hp., 200 1b. Per sq. in., with connections to upper and lower balloon flues. Direct gas-fired countercurrent rotary-kiln roaster for Cottrell dust. Necessary conveying equipment, described below. Instrumentation consists of: draft indicators, (3d hearth); various manometers; pyrometer served by thermocouples in each hearth, entrance and exit of waste-heat Joseph. entrance and exit of each hot Cottrell; roaster draft recorder and shaft air-pressure controller; temperature recorder and controller (10th and 12th hearths); SO* recorder (waste-heat boiler n

Jan 1, 1944

By Frank S. McKenna, Myron A. Pugacz, Clarence E. Jackson

THE notched-bar impact test has proved worth while in certain applications as a test for control of the quality or the heat- . treatment of steel. In view of the serious thought that even so simple a test as the tensile test, has evoked during the past years, it is not surprising that the notched- bar impact test should have inspired much experimental work. The correlation of the great number of data has not been successful, although steady progress has been made toward a better understanding of this test. Progress has been made, especially, in the isolation of the effects of the many variables that control the results. The stress system imposed on a specimen with a notch is so complicated and un- predictable that no simple evaluation of the test has been possible. Because of this uncertainty, many engineers hesitate to use the notched-bar impact test, and this attitude may well continue until a better understanding of the effects of the variables in the test are available. Without doubt, any additional data that may be presented should be accompanied by as complete a description of the details of test as possible, so that it may be added to the general fund of information that is to serve as the basis for the theory of the notched-bar impact test. The many factors that may control the test results have been pointed out repeatedly. The importance of the effect of the type and dimensions of the specimen has been recognized. Most of the work reported by American investigators has been limited to small- size (Charpy) specimens tested as a simple beam; two types of notches (Fig. I) have been commonly used. Considerable data have also been presented by many investigators using a small specimen tested as a cantilever beam; this commonly being called the Izod test. Here, however, a shear component of stress makes the stress system even mare complex than that present in the simple beam type of test, hence a critical analysis is difficult. Much work has also been reported by investigators using the tension type of specimen. A second variable that must be con- trolled is the testing temperature. An indication that the tests were performed at room temperature is not sufficient, since in many steels a variation of a few degrees in the actual testing temperature may be sufficient to give an entirely different range of results. Other factors. such as the com- position and condition of the material being tested and the speed of test, should also be considered. Many investigators have contributed data and theoretical discussions on the problems encountered in notched-bar test-

Jan 1, 1944

By Robert M. Dreyer

AGGREGATE With an annual domestic production of over 1.6 billion tons at a value of over $2 billion (see Table 15.1.1), the production of aggregate (crushed rock, sand, and gravel) is a basic industry of utmost economic importance. Because of the role of aggregate materials as essential ingredients of concrete, asphalt surfacing, and plaster, their delivered prices are major factors in determining the cost of construction. The annual domestic production comes from nearly 10,000 plants. About 15% of these plants account for over one-half the production. In a rapidly inflating economy, the average mine sales price of aggregate has remained relatively stable. The actual mine sales prices, however, vary greatly depending on quarrying costs in various parts of the country. Of much more importance in construction costs, however, is the delivered price of aggregate. This varies for each job, depending on the distance from the quarry and resulting transportation costs, as well as the initial cost at the mine. Because of a proliferation of regulations limiting new quarries in the vicinity of the encroaching urban sprawl, the average distance which aggregate must be transported has been increasing rapidly. Although it is impossible to derive an average delivered cost for aggregate, it should be noted that even an increase of only $1 per ton in average delivered cost over the last decade (probably a minimal assumption) would mean an annual cost $1.5 billion higher than ten years ago. In recent years, structural engineering considerations, as well as an increasing use of lightweight concrete blocks, have resulted in a rapidly increasing demand for lightweight concrete and plaster, the essential ingredient of which is lightweight aggregate. Principal lightweight aggregates are: pumice, slag, perlite (thermally expanded hydrous volcanic glass), vermiculite, and expanded shale, formed by the thermal expansion of shale and slate. The United States now has the capacity to expand, annually, over 13 million tons of shale and slate and to expand over 600,000 tons of perlite. In locating a site for aggregate production. the following factors must be considered: (1) tonnage available; (2) quality of aggregate (including local variations); (3) distance from major use areas; (4) transportation costs, including those resulting from present and possible future haulage restrictions; (5) zoning regulations; (6) operating costs, including the cost effects of compliance with local regulations governing blasting, air pollution, water pollution and drainage, noise levels, and operating periods. At one time, locating a suitable site for the production of crushed rock, sand, or gravel, in most areas, was regarded as an extremely simple task. In the past few years, however, finding a site for profitable production of aggregate has assumed ever-increasing com-

Jan 1, 1976

By H. W. Hindry

This paper presents the ingredients com-~osing a type of oil-base mud that has been successfully used in drilling oil horizons in California, the effect of ingredient concentrations on physical properties, methods of handling at the well and possible advantages of a waterless drilling fluid with excellent plastering properties. Introduction An oil-base mud is a rotary drilling fluid in which oil has been substituted for water as the principal liquid ingredient. In recent years such a mud has been developed and used successfully for drilling the oil horizons of wells in various Calilornia fields. There are several types of oil-base mud, but only the type that is currently used to any appreciable extent will be considered at this time. The oil-base drilling-mud compositions used by Shell Oil Company, Incorporated have been covered by several patent applications on which patents are expected to issue at an early date. The purpose of this paper is to present data on the fundamental design of the mud; the ingredients used and their specifications; the effect of ingredient concentration on physical properties; the selection of the proper mud; the facilities needed for handling the mud; and a general discussion on drilling with oil-base mud. In view of the early stage of development of oil-base mud, the great number of vari- ables, and the almost unlimited possible combinations of these. variables, which in turn require extensive laboratory study, there are certain irregularities and omis. sions in the data presented here. However, it is believed that sufficient data are at hand to permit a fairly complete analysis of the characteristics of oil-base muds. In view of the excellent plastering properties of oil-base mud when properly proportioned, its use should: (I) minimize the possibility of impairing the natural flow potentialities of the producing horizon such as that resulting from infiltration of water from water-base muds; (2) permit smaller clearances for setting liners, since the mud sheath has no appreciable thickness; (3) eliminate the possibility of clogging the perforations of the liner with thick mud sheath; (4) facilitate the removal of the mud sheath from the walls of the hole, for its mud sheath has no appreciable strength; (5) assist in drilling through formations, such as "heaving shale," where water wetting appears to be a source of difficulty. (6) permit cores to be obtained without contamination from drilling water. Fundamental Design of an Oil-base Mud In the design of any rotary drilling mud it is necessary to select materials that will fulfill the following requirements: (I) act as the liquid medium and regulate the viscosity; (2) impart initial and final plastering properties; (3) give gel strength and structure in order to prevent settling; (4) serve as a weighting material. The

Jan 1, 1941

By H. W. Hindry

This paper presents the ingredients com-~osing a type of oil-base mud that has been successfully used in drilling oil horizons in California, the effect of ingredient concentrations on physical properties, methods of handling at the well and possible advantages of a waterless drilling fluid with excellent plastering properties. Introduction An oil-base mud is a rotary drilling fluid in which oil has been substituted for water as the principal liquid ingredient. In recent years such a mud has been developed and used successfully for drilling the oil horizons of wells in various Calilornia fields. There are several types of oil-base mud, but only the type that is currently used to any appreciable extent will be considered at this time. The oil-base drilling-mud compositions used by Shell Oil Company, Incorporated have been covered by several patent applications on which patents are expected to issue at an early date. The purpose of this paper is to present data on the fundamental design of the mud; the ingredients used and their specifications; the effect of ingredient concentration on physical properties; the selection of the proper mud; the facilities needed for handling the mud; and a general discussion on drilling with oil-base mud. In view of the early stage of development of oil-base mud, the great number of vari- ables, and the almost unlimited possible combinations of these. variables, which in turn require extensive laboratory study, there are certain irregularities and omis. sions in the data presented here. However, it is believed that sufficient data are at hand to permit a fairly complete analysis of the characteristics of oil-base muds. In view of the excellent plastering properties of oil-base mud when properly proportioned, its use should: (I) minimize the possibility of impairing the natural flow potentialities of the producing horizon such as that resulting from infiltration of water from water-base muds; (2) permit smaller clearances for setting liners, since the mud sheath has no appreciable thickness; (3) eliminate the possibility of clogging the perforations of the liner with thick mud sheath; (4) facilitate the removal of the mud sheath from the walls of the hole, for its mud sheath has no appreciable strength; (5) assist in drilling through formations, such as "heaving shale," where water wetting appears to be a source of difficulty. (6) permit cores to be obtained without contamination from drilling water. Fundamental Design of an Oil-base Mud In the design of any rotary drilling mud it is necessary to select materials that will fulfill the following requirements: (I) act as the liquid medium and regulate the viscosity; (2) impart initial and final plastering properties; (3) give gel strength and structure in order to prevent settling; (4) serve as a weighting material. The

Jan 1, 1941

By E. W. Filer, R. P. Smith, L. S. Darken

The solubility of nitrogen gas in purified iron and low alloy steels is determined for the y region (930° to 1350°C). The diffusivtiy of nitrogen is estimated from the rate of approach to equilibrium. The investigation of aluminum-killed steels, held in nitrogen, discloses precipitation of aluminum nitride, the solubility of which is determined. ALTHOUGH several investigations of the solu-bility of nitrogen gas in y iron have been reported, all have made use of the method adopted by Sieverts in his classic work, whereby the solubility is determined by the pressure or volume change of the gas. The agreement between different investigators* is rather poor, particularly as compared to the self-consistency of results of several individual investigators. The present report represents a portion of our investigation of the equilibrium of nitrogen and nitrogenous atmospheres with iron and steels. The method adopted in this temperature region (910" to 1400°C) consists of holding the specimen in gaseous nitrogen, quenching (or cooling), and determining the nitrogen content by direct analysis (solution in acid followed by distillation and titra-tion of the ammonia).** Up to 1050°C a 20 in. vertical wire-wound (Kan-thal) furnace was used; this was wound in three sections so that by proper adjustment of relative currents, and use of a modulator1 and a commercial controller (using a chromel-alumel control couple), a zone almost 6 in. long could be maintained uniform within a few tenths of a degree. Since the temperature coefficient of the nitrogen solubility is low, the full precision was not utilized and a variation of l° to 2" was tolerated; a variation of a similar amount also occurred occasionally between the beginning and end of the experiment. At higher temperature a vertically mounted, tubular Globar furnace and control unit was used; the zone of uniformity (l° to 2"C) was here limited to about 2 in.; fluctuations with time were comparable to those in the wire-wound furnace. Reported temperatures were measured by use of a platinum-platinum-rhodium thermocouple, which was frequently com- pared with a similar standard couple which was calibrated at the gold and palladium points and also compared with one certified by the Bureau of Standards; error from this source is believed to be less than 1 "C. Nitrogen gas from a commercial cylinder was mixed with slightly over 1 pct H by use of a gas mixer described previously.' This mixture was passed over hot copper and through ascarite and phosphorus pentoxide to remove oxygen and water vapor. The purified gas contained 1.05 pct H. This procedure was adopted to prevent the formation on the specimens of oxide film, which is well known to be nearly impervious to nitrogen; its success was attested by

Jan 1, 1952

By N. Van Wingen

EFFective sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated. Introduction In recent years many investigators have demonstrated the practical value of an accurate knowledge of the physical and dynamical characteristics of reservoir sands containing oil and gas. Of these factors, which serve to completely define a porous medium as a container or carrier of fluids, the dynamical characteristics are of particular interest to the production engineer because they afford a direct measure of the rate at which the oil or gas content of a reservoir will become available. The constant that defines dynamically the porous medium as the carrier of a homogeneous fluid in viscous motion is the "permeability." Coke-analysis Method The generally accepted practice in com-piling permeability data has been to analyze in the laboratory core samples taken in the course of drilling through the productive horizon, and to obtain the mean measure of the productive ability or permeability for the interval open to production by graphical integration of the permeability profile. An average permeability ascertained in this manner, however, is useful to the production engineer only for comparisons of wells drilled in the same horizon, as permeabilities determined in the laboratory are measures of only the ability of a porous medium to transmit a single fluid. As a result of many investigations, it has been shown, however, that under actual reservoir conditions water is coexistent with the petroleum and that its presence greatly reduces the permeability of the sand to oil. Empirical relationships showing the effect of the presence of any immiscible fluid A (such as water) in a porous medium on the permeability of the medium to a fluid B (such as oil) have been established separately by Hassler,1 Dunlap,2 and the writer (Fig. I),3 so that the average specific or dry-core permeability as determined in the laboratory can be corrected to give the true measure of the ability of the horizon penetrated to transmit oil, provided the percentage of pore space occupied by connate water is known accurately.

Jan 1, 1942

By N. Van Wingen

EFFective sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated. Introduction In recent years many investigators have demonstrated the practical value of an accurate knowledge of the physical and dynamical characteristics of reservoir sands containing oil and gas. Of these factors, which serve to completely define a porous medium as a container or carrier of fluids, the dynamical characteristics are of particular interest to the production engineer because they afford a direct measure of the rate at which the oil or gas content of a reservoir will become available. The constant that defines dynamically the porous medium as the carrier of a homogeneous fluid in viscous motion is the "permeability." Coke-analysis Method The generally accepted practice in com-piling permeability data has been to analyze in the laboratory core samples taken in the course of drilling through the productive horizon, and to obtain the mean measure of the productive ability or permeability for the interval open to production by graphical integration of the permeability profile. An average permeability ascertained in this manner, however, is useful to the production engineer only for comparisons of wells drilled in the same horizon, as permeabilities determined in the laboratory are measures of only the ability of a porous medium to transmit a single fluid. As a result of many investigations, it has been shown, however, that under actual reservoir conditions water is coexistent with the petroleum and that its presence greatly reduces the permeability of the sand to oil. Empirical relationships showing the effect of the presence of any immiscible fluid A (such as water) in a porous medium on the permeability of the medium to a fluid B (such as oil) have been established separately by Hassler,1 Dunlap,2 and the writer (Fig. I),3 so that the average specific or dry-core permeability as determined in the laboratory can be corrected to give the true measure of the ability of the horizon penetrated to transmit oil, provided the percentage of pore space occupied by connate water is known accurately.

Jan 1, 1942

By John R. Green

ROTARY kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary according to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. MEASUREMENTS OF KILN TEMPERATURE The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration.. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records or automatic control are desired, while optical pyrometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. I shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected from puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly o° to over 200°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without. effect of the flame temperature. There should be some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors Influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and com¬ments on the possibility of measurement and control. Of greater number and of varied influ¬ence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1941

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By Alfred R. Powell

Late in 1944 a group of petroleum and coal technologists was organized in Washington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Tehnical oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. since oil-production facilities in Germany and the occupied countries controlled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Induslrial Intelligence Com,mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A summary of the more important information gained by this combined British and American mission is presented below. German Oil Production The oil available to Germany, both natural and synthetic, and including production from occupied countries, reached a peak in late 1943 and early 1944 Production at this time was at the rate of 1,200,000 metric tons Per month, equivalent to 100,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, jo per cent was crude oil from Romania and Hungary, 12 Per cent was crude oil from Germany itself, including Austria, 9 per cent cumprised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of wartime production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syrlthetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per Cent of the peak qualltity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1947

By Alfred R. Powell

Late in 1944 a group of petroleum and coal technologists was organized in Washington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Tehnical oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. since oil-production facilities in Germany and the occupied countries controlled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Induslrial Intelligence Com,mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A summary of the more important information gained by this combined British and American mission is presented below. German Oil Production The oil available to Germany, both natural and synthetic, and including production from occupied countries, reached a peak in late 1943 and early 1944 Production at this time was at the rate of 1,200,000 metric tons Per month, equivalent to 100,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, jo per cent was crude oil from Romania and Hungary, 12 Per cent was crude oil from Germany itself, including Austria, 9 per cent cumprised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of wartime production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syrlthetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per Cent of the peak qualltity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1947

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By Claudia Gasparrini

Gold, silver and platinum-group elements occur normally in very low concentrations in their ores. Because their market value is in many situations high enough to justify their full recoveries, mineralogical studies before any routine recovery is attempted are particularly important for the description of their manner of occurrence and decision on the appropriate recovery techniques. Gold and silver, although sometimes treated by similar metallurgical processes, may require different approaches and treatments because of the different manner in which they occur in their ores: gold has a relatively simple mineralogy limited to native gold, electrum and less often tellurides. Silver has a very complex mineralogy including over 200 different minerals. On the other hand, gold is more often than silver recovered from ores where its fine grain size requires the breaking of the host minerals by chemical methods. Mineral, grain sizes and host minerals all affect the metallurgy of the platinum-group elements..

Jan 1, 1984

By W. M. McKewan

Dense magnetite pellets were reduced in hydrogen-water vapor-nitrogen mixtures over a temperature range of 400° to 500° C at a pressure of 0.97 atm. The rate of reduction per unit area was found to be constant with time and directly proportional to the partial pressure of hydrogen at a constant ratio of water vapor to hydrogen. Water vapor poisoned the oxide surface by an oxidizing reaction and markedly slowed the reduction. The enthalpy of activation was found to be + 13,600 cal per mole. THE investigation of the reduction of iron oxides has been the subject of numerous papers. Most of these papers have dealt with the evaluation of various ores, both magnetite and hematite. There have

Jan 1, 1962

MISCELLANEOUS U.S. 0,029,598 - Extraction of vanadium values from vanadiferous iron oxide ore. A pelletized mixture of ore, limestone and bentonite is roasted in an oxidizing atmosphere to form calcium vanadates, the calcine ground, the ground material leached with aqueous ammonium carbonate or sodium carbonate to produce a vanadium-rich solution while leaving an insoluble residue of calcium carbonate and/or calcium bicarbonate along with undissolved iron values, and the solution separated and treated for its vanadium content. This patent is a reissue of U.S. Patent No. 3,853,982, dated Dec. 10, 1974. C. B. Bare and J. W. Pasquali, assigned to Bethlehem Steel Corp. Mar. 28, 1978. 7 pp. (423-68). Filed: 3-3 1-77 (783,352).

Jan 1, 1979

NEW MEMBERS The following list comprises the names of those persons who became members during the month of December, 1913: Members ADAMS, CHARLES W., JR., Smelting, American Smelting & Refining Co., Murray, Utah. ARMSTRONG, FRANK H., Mechanical Engineer Vulcan, Mich. ARNOLD, JOHN B., Attorney-at-Law Room 840,200 5th Ave., New York, N. Y. BOYS, HARRY R., Mining Paso Robles, Cal. CAVANAGH, JOHN L., Min. Engr., Nova Scotia Steel & Coal Co.; Wabana, Newfoundland. CHOW, KAI CHI, Student 1120 Amsterdam Ave., New York, N. Y. CLARK, ARTHUR B., Mining Engineer 72 Harbour Bldg., Butte, Mont. CURLEY, JOHN R., State Mine Inspector P. 0. Box 633, Leadville, Colo. DAVIS, ANGUS W., Mining Engineer, Consolidated Mining & Smelting Company of Canada, Trail, B. C., Canada.

Jan 1, 1914