Search Documents

By J. T. Eash, E. M. Wise

MANY of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile properties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. SCOPE AND CONCLUSIONS Tensile tests were carried out at room temperature and elevated temperatures up to 11000 C. on previously well annealed samples of platinum, palladium and several of their important alloys with compositions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100° C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the- other materials tested. The tensile strengths of palladium and the palladium alloy at 1100° C. are from 10 to 11.2 per cent of the room-temperature values. The elongations of platinum and its alloys tend to increase at tempera¬tures above 600° to 800° C., while the two samples of pure palladium show a maximum at 600° C.

Jan 1, 1938

By J. E. Willson, N. K. Bohidar

An evaluation of internal stress distribution based on photoelastic studies and destructive testing of simulation models shows that pillar failure is a function of the internal stress distribution, and that stability can be changed by altering the internal stress pattern. Induced stresses in three-dimensional epoxy disks subjected to uniaxial forces were evaluated by photoelastic studies. Stress profiles across different sections perpendicular to the loading direction revealed two maxima for each profile. Based on the stress distribution for the entire column, an attempt was made to explain pillar spalling and the hour glass pattern of failure in a mine pillar. For maximum stability and optimum design of mine pillars, it is necessary to consider the external forces, the nature and distribution of induced stresses and the characteristics of the pillar material as determined in the laboratory. This paper summarizes the research done by N. K. Bohidarl and Ben L. seegrniller2 as partial fulfilment of the requirement for Master of Science degree in Mining Engineering, University of Utah. It is an evaluation of a study to determine the stress distribution in short columns in order that regions of high stress concentration in mine pillars may be found and their effect on pillar failure be ascertained. The ratios of the dimensions of the columns studied are representative of those found in mines located in flat-bedded deposits. The weight of the overburden generally constitutes the major external force. This force is calculated by taking into account specific weight and thickness of the cover. Determination of the distribution of this force on pillars may often require a complex analytical study. There have been many investigations of the strength

Jan 1, 1968

By L. D. Jaffe, D. C. Buffum, F. L. Carr

SINCE the temper brittleness of steels is generally considered to be a grain-boundary phenomenon¹,² it would be expected that austenitic grain size would affect temper brittleness. Several investigators"" reported that temper brittleness, as measured by room-temperature impact tests, increased as the austenitiz-ing temperature was raised. It was subsequently pointed out that conclusions as to temper brittleness based upon room-temperature impact tests are likely to be misleading.1,6 Hurlich7 used a range of testing

Jan 1, 1954

Separates of all the Technical Publications published in 1930 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the TRANSACTIONS. Copies of these papers have been mailed to those members of the Institute who are registered in Classes A-Mining Methods; B-Milling and Concentration; C-Iron and Steel Division; D-Non-ferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Non-metallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting, respectively. Other members may obtain copies by writing to the Secretary. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. METAL MINING TECH¬ NICAL PUBLI- TITLE AUTHOR MEETING TRANS CATION VOLUME No. AND PAGE* 264-A.29. Quicksilver Industry in 1929. Im- L. H. Duschak San Francisco T30, 283, 312 provements in the Metallurgy of C. G. Maier and Oct., 1929 Quicksilver and Symposium on The others Present Status of the Quicksilver Industry (With Discussion) (37) 271-A.30 Observation on Ground Movement R. E. Palmer New York T30,168 and Subsidences at Rio Tinto Feb., 1930 Mines, Spain (20) 274-A.31 Development and Installation of the C. L. Berrien New York T30, 139, 166 Hawkesworth Detachable Bit (29) . Feb., 1930 276-A.32 Protective Measures Against Gas O. A. Glaeser New York T30, 129, 187 Hazards at United Verde Mine (11) Feb., 1930 287-A.33 Use and Cost of Compressed Air (12) R. S. Lewis New York Feb., 1930 314-A.34 Miami Copper Company Method of F. W. Maclennan New York T30, 39, 80 Mining Low-grade Orebody (44) Feb., 1930 319-A.35 How Human Beings Respond to W. J. McConnell New York Changing Atmospheric Conditions Feb., 1930 (9)

Jan 1, 1930

By Albert F. J. Bordeaux

This paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there mas a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. General Outline of the Cyanide Treatment. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed: 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By Arthur G. Levy, Henry M. How

The purpose of the investigation on which this paper is based is to determine whether the structural change which occurs in the slow cooling of steel below the transformation range has an important effect on its engineering properties. We recognize two distinct things which occur in steel when it is brought from above to below the transformation range, first, the transformation proper, that is, the breaking up of the austenite or solid solution of the cementite in the remainder of the iron, and the liberation of its components as undissolved cementite and as ferrite or alpha iron; and second, a structural change consisting in the gradual coalescence of the ferrite and cementite respectively into larger and larger separate masses. Let us distinguish these from each other by speaking of them as " the transformation " and " the structural change " respectively. If the cooling is at all rapid the unevenness of contraction induces severe stress; so that in a sense a slow cooling has a third influence, the prevention of such stress. This transformation from austenite to ferrite plus cementite can complete itself only below the transformation range; and, because this structural change is a change in the structural arrangement of the products of that transformation, it too can complete itself only at temperatures below that range, say below 725°; and of these temperatures it is only those between 600° and 725° that give the metal sufficient mobility to permit this structural rearrangement to progress with ally rapidity. The transformation is now known to be rapid, but the structural change is relatively slow. The transformation, the liberation of the dissolved cementite from the state of solution in the austenite to a free state, leaves the steel structurally in the

Jan 1, 1913

By Arthur F. Taggart

PROGRESS in a technical art is of several kinds. It springs .from many diverse sources. It comprises invention, mechanical improvement, operating advance, analytical study, education. Invention is, by definition, a relatively great, essentially individual step, taken quickly. Operating advance is the slow, cumulated march of practice; in contrast, it moves at the pace of the tortoise, but over, the years its effects rival and, in some cases, surpass those of invention. Mechanical improvement- is a usual concomitant of the reduction of invention. to operating practice; thereafter it is a primary tool of operating advance. Analytical study is the process of mental digestion of the fruits of invention and practice. Its purpose is to render these into a form assimilable by the art as a whole, and by the perennial crop of would be practitioners. Education, disseminating the results of such study, consolidates and maintains the positions gained. Thus, slowly at first, but continuously accelerating, the tide of progress grows- to flood. Such growth, in mathematical parlance, is expressible in the general form y = mxn, where x is time, n is some positive number greater than one, m is another positive number, and y is the state of the action at instant x. When n is 2, the readers will recognize the graph of the equation as one branch of the familiar square parabola, whose property it is to become parallel to the y-axis; i.e., to move at an infinite rate, in that never-never

Jan 1, 1947

IN this survey of the progressive development of education for the mineral industries throughout the United States, the review of the history of each school has usually been completed wherever it is first mentioned, but the history of the schools in the cities of the eastern seaboard was not carried beyond 1870. It is necessary now to cover what happened during the period of approximately the last quarter of the nineteenth century in several of the schools in the east. PHILADELPHIA Of Philadelphia, it has been related in chapter 4 that the Polytechnic College of Pennsylvania began offering a curriculum leading to the B.S. in mining in 1853; that the school did not prosper, and finally closed about 1890. The establishment of a Department of Mining, Arts, and Manufactures at the University of Pennsylvania in 1855-56 was also mentioned, but its history was not carried beyond 1860. In 1859 J. Peter Lesley was appointed professor of mining in the University of Pennsylvania. The son of a cabinetmaker, born in Philadelphia Sept. 17, 1819, he had taken his A.B. degree at the University of Pennsylvania in 1838 and then secured a position on the Geological Survey of Pennsylvania under H. D. Rogers. When the Survey was discontinued, in 1841, he went to Princeton to study theology, was ordained a Presbyterian minister and followed that career until 1853, when the Pennsylvania Geological Survey was again started and he rejoined its staff. He published "A Manual of Coal and its Topography" in 1856, and studied at the École des Mines, Paris, in 1850-57. He published an 800-page "Iron Manufactures Guide" the year that he was appointed to the staff at the University of Pennsylvania. In 1863-64 a College of Agriculture, Mines, Arts and the Mechanic Arts was established, but it was not a separate school

Jan 1, 1941

By J. A. Marton, N. Brown, M. Herman

AT high temperatures a deformed polycrystalline metal shows grain-boundary displacement in preference to slip lines.' This has led to the conclusion that overall strain at high temperatures is produced chiefly by grain-boundary displacement. Detailed microscopic examinations of individual grain boundaries have shown many interesting ways by which their displacement occurs; sometimes no grain deformation was observed except possibly in the immediate neighborhood of the boundary. However, X-ray examinations show that at high temperatures subgrain formation occurs;Y he process, generally called polygonization, results from lattice bending and the subsequent climb of dislocations to form low-angle boundaries. Quantitative measures of the grain-boundary displacements show that they make a minor geometrical contribution to the overall strain; the major contribution is made by grain deformation."'" A relationship between grain-boundary displacement and grain deformation was suggested by McLean, who showed how the degree of polygonization would determine the amount of grain boundary displacement: and by Dorn, who showed that for a given creep stress, the amount of grain-boundary shear was related to the overall strain and was independent of temperature.' Although the grain-boundary displacement may make a small geometrical contribution to overall strain, it may still be the rate-controlling factor in high-temperature creep. If in general grain-boundary displacement and grain deformation are dependent quantities, then the designer of a creep-resistant metal would like to know whether it is more desirable to strengthen the matrix of the grain or to increase the strength of its boundary. The widespread interest in the relationship between temperature and grain-boundary displacement makes it desirable to test the generality of Dorn's result6 that the ratio of grain-boundary displacement to overall strain is independent of the temperature for a given creep stress. In this investigation p-brass was used because it produces sharp grain-boundary displacements above 400°C. Since B-brass undergoes an order-disorder transformation which abruptly strengthens the grain, it is an excellent metal for determining whether grain-boundary displacement or grain deformation is the rate-controlling factor in creep. The problem will be confined to the temperature range where

Jan 1, 1958

This story of the salting of a supposed diamond mine is a part of our Western history and deserves to be recorded in this book. It was more than a local affair, because it was concerned with persons in London and New York, as well as San Francisco. Part of the story has been told by Asbury Harpending in a little book published 12 years ago. Harpending (who died at New York in 1923) was in London in March, 1872, when he received a cable dispatch from William C. Ralston, the president of the Bank of California, stating that "a vast diamond field" had been discovered "in a remote section of the United States". Before starting for San Francisco, Harpending had an interview with Baron Rothschild, who showed a lively interest in the story, which was as follows: two weather-beaten prospectors went to the Bank of California and deposited some uncut diamonds and rubies for safe keeping; these precious stones were estimated to be worth $125,000. The men said that they had found the gems in "a desert portion of the West". They departed quietly, but the story was told in business circles; whereupon George D. Roberts, a mining engineer of wide experience and an associate of Ralston, sought an interview with the prospectors. One of them proved to be a man that had been in the employ of Roberts. Both prospectors, named Slack and Arnold, appeared "coy and cautious"; they were "simpleminded fellows", and were "afraid to trust anyone with the momentous secret ". They refused to divulge the place of discovery and declined "to part with their rights", but later "they became more amenable to reason" and expressed willingness to sell a half interest to

Jan 1, 1932

By E. L. Larison

DURING the early years of the present century a notable interest appeared in American industry in the matter of recovering and render-ing profitable byproducts of manufacturing operations. Among the byproducts of reduction of sulfide ores in many plants large amounts of sulfur dioxide gas were available. In certain instances the concentration of SO2 in the gases evolved was, or could be made, sufficient to make them suitable for manufacturing sulfuric acid. At the Anaconda Reduction works such a condition existed. Large tonnages of copper concentrate were being roasted and the roaster gases were available and suitable as a source of sulfuric acid. Earlier work on a large scale at Martinez, Calif., and in the Ducktown region, Tennessee, had shown the feasibility of manufacturing sulfuric acid from the SO2 contained in gases arising from the reduction of copper sulfide ores. In California and Tennessee the acid found a ready market in manufacture of fertilizers, while the situation regarding disposal of the sulfuric acid was quite different at Anaconda. No local use for acid existed, and a commodity of such low value could not stand freight charges to consuming centers. There was a very large accumulation of sand tailings from the gravity concentration mill below the plant at Anaconda. This material, made by the comparatively crude methods in use up to about 1915, contained about 13 lb. of copper per ton, largely as sulfide minerals. In 1912 serious research work toward recovery of this copper was instituted and after about two years of laboratory and pilot-plant development, a process for accomplishing it was perfected. This process involved roast-ing the sand tailings, leaching the roasted tailings with sulfuric acid, and throwing out the copper by passing the solutions over scrap iron. Under this plan each ton of sand required the introduction of about 70 lb. of 60° Be. sulfuric acid.

Jan 1, 1934

By Charles L. Harness

MINERAL pigments give color, opacity, or body to paint, stucco, plaster, mortar, cement, linoleum, rubber, and similar materials. They must be finely divided, substantially insoluble, and generally inert for such uses. Inorganic pigments may be grouped somewhat arbitrarily as follows: A. Natural mineral pigments dug from the earth. 1. Those consisting mostly of iron oxides, such as hematite and Limonite. 2. Those containing large amounts of clay or noncoloring matter, such as ocher, sienna, umber, and colored shales. 3. Those whose color is not due to iron oxide, such as Vandyke brown (including sap brown, an alkali extract of Vandyke brown), graphite, and terre verte. B. Synthetic pigments. 1. Those containing iron oxide as the essential coloring matter, such as "pure" reds, yellows, and blacks, and Venetian reds. 2. Those not containing iron oxide, such as lithopone, zinc white, titanium white, ultramarine, Prussian blue, and the like. Only groups A and B-1 are discussed here. All the pigments in those two categories, except Vandyke brown, sap brown, and some of the carbonaceous slates, contain, as their essential color constituents, one or more compounds of iron; namely, an oxide-Limonite (2Fe203.H20 to Fe203.4H20), hematite (Fe203), or magnetite (Fe203.FeO). Man's first permanent coloring materials were earth pigments- the ochers, iron oxides, and various iron-stained clays. The caves occupied by prehistoric man and the arts of the ancient Chaldean, Egyptian, and Cretan civilizations bear mute witness to this and also testify to the beauty and permanence of earth colors. As the Roman era developed, earth pigments were pushed from their pre-eminent position by white lead and red lead and in the Middle Ages by zinc oxide. Today, of course, the number of acceptable pigments is very large and on a value basis the group of natural and synthetic earth pigments stands

Jan 1, 1949

ALTHOUGH iron ores occur in many parts of Sweden the two principal deposits are those at Grängesberg (see accompanying map) and at Kiirunavaara-Gellivare. Both of these deposits are con-trolled by a holding company, Trajikaktiebolaget Grängesberg-Oxelösund, which sells annually about one-half of, the iron in ore traded in world markets and has a fleet of 24 seagoing ore boats, with a total dead weight capacity of 172,500 tons. Because of its pre-eminence in international iron ore trade a brief outline of its operations will be of interest. ORE DEPOSITS OF GRÄNGESBERG The Grängesberg deposits have been known since the Middle Ages, but up to the middle of the nineteenth century the ore was transported from the mines to the furnaces in winter in. sleighs. Railway building began in 1853, and in 1873 the complicated structure of capital investment was tottering, but the basic bessemer process created a demand for ore high in phosphorus, as this is, and refinancing on the initiative of Sir Ernest Cassel put the principal operation on a firm footing. There are numerous property owners in the district, but they are all controlled by a joint administration board, and 90 per cent of the ore is produced by a subsidiary of the Grängesberg company from proper-ties which it either owns or leases. The ore, a mixture of magnetite and specular hematite, is in lenticular bodies, dipping about 70 E. in. fine-grained gneiss, and contains about 61 per cent Fe and 1 per. cent. P. There are two principal veins; the total ore reserves to a depth of 500 meters are estimated at 150,000,000 tons. As seen in the accompanying illustration, the ores were first worked in open cuts, but eventually underground shrinkage stoping was adopted. Difficulties were encountered in the support of the workings and from the freezing of the ore in the stopes, so slicing was adopted, although block-caving is used in one place. Most of the mining is now done at a depth "of 150 to 190 meters. The present annual output is about 1,400,-000 tons of crude ore, which yields about 1,000,000 tons of concentrate after being subjected to magnetic con-centration and jigging.

Jan 1, 1927

By J. M. Donkers, R. de Groot

The various objectives of dredging at sea require different methods and radically different equipment for their optimum fulfillment. In the majority of cases, sea dredging is done by means of dredging equipment connected to a pontoon or ship floating at the surface. As the supporting hull is subject to the influence of waves, swells, currents and wind, the connecting point of the dredging equipment to the hull will generally move relative to the sea bottom with 6° of freedom. The more important hull motions are surge, heave, pitch and roll. Depending on the actual sea and weather conditions and the size of the hull, some of these motions can be so large that dredging equipment of rigid construction (normal or inland dredges) cannot be used. In those cases where mechanical disintegration of the bottom is necessary and where accurate dredging is required, the designer must find a solution for this problem. For cases where the bottom consists of soils that can be handled by plain suction, highly sophisticated dredging equipment such as the trailing suction hopper dredge permit dredging under all but the most severe sea state conditions. This type of dredge picks up the soil from the sea bottom while slowly underway. The drag suction head is fitted on a suction pipe of such flexibility that the supporting ship can carry out all six movements in relation to the draghead (heave, pitch, roll, sway, yaw and surge), while the draghead remains in firm contact with the bottom. The suction pipe is fitted with flexible hoses, a universal hinge, a horizontal hinge, axial turning gland and sliding turning gland with horizontal axis and is suspended flexibly from the ship incorporating swell compensating buffer gear, keeping the wires taut and the draghead bottom contact pressure fairly constant while the dredge moves up and down. Due to the fact that the draghead has a low bottom contact pressure and has little tendency to sink into the bottom, this compensation is not difficult to realize.

Jan 4, 1974

By G. D. Arsdale

This paper describes a series of experiments leading to the development. of a method for leaching the mixed ores of the Inspiration Consolidated Copper Co., containing chalcocite and silicates of copper, by the use of solutions acidified with sulfuric acid and carrying ferric sulfate. Iron is added to the solutions and ferric iron is regenerated electrolytically to a percentage high enough to act as an efficient solvent. The decreased yield is partly compensated for by a higher current density. AN IMPORTANT problem in modern copper metallurgy, particularly in the Southwest, has been to obtain good recoveries from what are commonly known as mixed ores; that is ores in which the copper occurs partly as oxide and partly as sulfide compounds. The dividing line between mixed ores and ores commonly accepted as concentrating is not definite. In other words, much ore now being concentrated carries considerable copper in non-sulfide form, on which recoveries are hot so good as on ores carrying less of these constituents. While treatment by concentration may be commercially profitable, on ores carrying oxide copper within certain limits, there are large deposits for which the application of con-centration could not be considered, and yet which have not been considered amenable to leaching because they carried too much sulfide. The Inspiration Consolidated Copper Co. has large amounts of such mixed ores, and this paper is an account of the experimental work by which a method was developed for their treatment, and for which a large plant is now being erected by the Inspiration Co. It is not claimed that the method is a general solution of the problem of mixed-ore treatment but it is apparently well adapted for leaching the ores of the Inspiration Co., for which it was designed. The work done has covered preliminary laboratory and test-plant investigation, and .a pilot-plant run, extending from March to the middle of December, 1923. Thoroughly consistent and satisfactory results, were obtained continuously for more, than six months in the pilot plant; and it is believed that the results; and probable costs that can be had on a large scale have been definitely, proved. The method, however, was designed for local conditions; and while the basic principles are general, there are ores on which it will not work and other ores for which considerable modification may be required.

Jan 10, 1925

By Robert C. Stephenson

LARGE deposits of titaniferous magnetite occur associated with anorthosite and gabbro in the Lake Sanford area, Essex County, New York. The ore, gabbro, and anorthosite show consanguineous relations. Anorthosite grades through gabbroic anorthosite into gabbro but is locally intruded by gabbro. Structural and petrographic evidence suggests that gabbro was differentiated from anorthosite by filter pressing. Field and laboratory study of ore occurrences indicates that an ore residuum concentrated in the gabbro through magmatic segregation by normal crystallization and flowage. Ore occurs as bands which grade into gabbro, and also as large masses which replace anorthosite. Ore in the gabbro is finer grained and richer in ilmenite than ore in anorthosite.

Jan 1, 1945

By L. D. Jaffe, M. R. Norton, J. H. Hollomon

IN the practical heat-treatment of steel the decomposition of austenite usually occurs during cooling rather than at constant temperature. Nevertheless, the course of this decomposition has generally been studied only isothermally. Isothermal studies are not only simpler experimentally, but have the great theoretical advantage that one of the variables, temperature, is constant. It is the purpose of this paper to outline the principles that govern the relations between isothermal and anisothermal? decomposition of austenite, to present and systematize the available experimental information, and to indicate the gaps in the existing knowledge. Some of the experimental information is the result of new work. § Most of it is derived from scattered data in the literature. Many of these data were obtained incidentally in the course of research on other subjects and their significance has not been pointed out and perhaps not understood. It is hoped that this paper will aid future planning of more extensive research on anisothermal decomposition. METHOD In order to study the relations between isothermal and anisothermal decomposition, it appears fruitful to view anisothermal decomposition as taking place at a series of constant temperatures1 (except for the martensite reaction, which does not occur isothermally to an appreciable extent). When the time the steel is at each temperature is finite, the over-all amount of the reaction is considered to be the sum of the amounts occurring at each of the successive temperatures. During continuous cooling or heating, the time the steel is at each temperature and the difference between successive temperatures can be considered to approach zero. The over-all amount of transformation will then be given by integration over the range of temperatures involved. This point of view is advantageous in that it considers anisothermal transformation to be a series of isothermal transformations. The problem thus becomes one of determining the effect of partial decomposition at any given temperature upon subsequent decomposition at another temperature. Single Anisothermal Reaction Consider a phase brought to a temperature at which it is unstable, held there until it has partially transformed, and then brought to another temperature at

Jan 1, 1946

By C. G. McLachlan

This paper outlines a series of tests carried out during the first six months of 1927, in the laboratory and mill of the Moctezuma Copper Co. The object of the tests was to determine whether the soluble salts present in the mill circuit water were having a detrimental cffect on the recovery made by flotation. To accomplish this object a series of water analyses were made, followed by flotation experiments in which definite quantities of the salts found were added as addition agents. Before proceeding to describe the results obtained in the course of the investigation, reference will be made to five articles that have appeared during the last two years in which the action of such salts is discussed. Two of these are by A. T. Tye1, 2 and describe flotation practice at Cananea and the way in which water high in ferrous and ferric salts is conditioned for differential flotation. Two, one by A. C. Munro and H. A. Pearse3 and the other by H. A. Pearse,4 outline Britannia milling methods, and the advantages that have been derived from ore washing; while in the fifth, A. W. Hahn5 summarizes the results of laboratory experiments in which ferrous, ferric and aluminum sulfates have been added in varying amounts. The mill of the Moctezuma Copper Co. has a daily capacity of 3000 tons, and is situated about 75 miles south of Douglas, Arizona, on the Rio de Nacozari, in the Mexican state of Sonora. The ore treated is mined from the company's mine at Pilares, about 5 miles southeast of the Concentrator. This ore contains about 2.5 per cent. copper— present almost entirely as chalcopyrite—and 10 per cent. iron, of which

Jan 1, 1928

By John E. Conley

THE slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5 ¾ million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. USE OF WASTE SLATES FOR MAKING AGGREGATES The lightweight-aggregate industry has been discussed elsewhere4.5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done3 on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. REQUIREMENTS FOR RAW MATERIALS As pointed out by Hughes,4 the light-weight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of any low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig. I illustrates the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942

By Arthur B. Cummins

POWDERED nonmetallic minerals and rocks of many different types are used extensively in industry for incorporation in compositions and manufactured products The term "mineral filler" is commonly employed to designate a material that is used for a specific purpose but not as an essential or reactive component Such a definition is not without objections, and it is indeed difficult to define fillers in any fully satisfactory manner, since the term has come to have so many different meanings and to cover such a wide range of uses. A filler is defined, for the purposes of this chapter, as a substantially inert material not specifically employed as a reactive or essential component, the primary function of which is to modify the properties or processing of a composition of matter or fabricated article Emery1 has emphasized that fillers change the properties of the product but are themselves unchanged in compounding or use The term "filler" appears to be rather general when referring to usages m bituminous compositions, rubber, composition floorings, fertilizers, plastics, textile finishes, and some others. In paper manufacture, in the paint industry and with insecticides, other terms are frequently employed, as is indicated, herinafter By placing emphasis on the function of the material used in modifying the properties of the composition or article, it is believed that a more useful classification of filler products and their applications may be derived. FUNCTIONS OF MINERAL FILLERS All of the manifold functions of mineral fillers cannot be listed in a summary review. A survey of the uses for these materials, however, shows that in nearly all cases the powders are employed to modify the properties of a composition of matter or those of a fabricated article, or to perform some useful function In the manufacture of either. A generalized list of these useful functions may be given is follows 1 To Modify Optical Properties Color Surface texture Opacity Brightness and gloss (as in paper and plastics) Flatness (as in lacquers and paints)

Jan 1, 1949