Search Documents

Jan 1, 1895

By B. L. Averbach, Morris Cohen, S. A. Kulin

The martensitic transformation can be initiated by elastic stresses at temperatures above M. in a steel containing 20 pct Ni and 0.5 pct C. Shear strains and normal tensile strains acting on a potential habit plane promote the transformation but compressive strains oppose it. THE strain sensitivity of the martensitic transformation has long been recognized. It is now well known that martensite formation can be induced by plastic deformation at temperatures below, and not too far above, the M, point.' However, the exact role of elastic vs. plastic strains and of the concomitant stresses has proved to be a very elusive matter. Many investigators2-' of the steel hardening reaction have made use of the stresses resulting from volume changes to account for such observations as the existence of retained austenite and its variation across the section of a bar, the change in the amount of retained austenite with quenching rate, and the self-stopping nature of the transformation when the cooling is stopped. The effect of applied strain as an independent variable has been studied in 70 pct Fe-30 pct Ni alloys by Scheil7 and McReynolds.8 Some data are also available for lithium and Li-Mg alloys,9 Cu-Zn,10 Cu-Sn and Cu-A1 alloys," and aus-tenitic stainless steels."-" It has been found that martensite formation can be induced isothermally, even at temperatures above M,, by mechanical deformation of the parent phase. The competitive nature of plastic yielding by slip and by the martensitic reaction has been depicted by Scheil.7 Basically, Scheil postulated that: 1—at temperatures not too far above M, (where austenite is less stable than martensite), a critical resolved shear stress (within the elastic range) is required to promote the transformation to martensite; 2—at and below M,, the austenite lattice becomes mechanically, as well as thermodynamically, unstable and shears over spontaneously into martensite without the application of external stress; and 3—at temperatures sufficiently far above M8, the critical resolved shear stress for martensite formation increases to a level above that required for slip, and plastic flow then supersedes the transformation when external stress is applied. Scheil's concepts were tested by McReyno1ds8 ho found no change in the elastic moduli (measured both statically and dynamically) of 71 pct Fe-29 pct Ni alloys in the vicinity of the M, temperature. Since the moduli did not approach zero or become negative on cooling to M,, it was concluded that the austenite lattice does not become mechanically unstable at M2, as postulated by Scheil. McReynolds also reported that M, is not raised by elastic stresses. Accordingly, plastic deformation was considered to stimulate the transformation by generating martensite nuclei in the distorted regions of the parent phase. The above issues with regard to the role of applied stress require clarification, if a basic understanding of the martensitic transformation is to be obtained. For example, in the reaction-path theory,'"," it is postulated that strain embryos exist in the austenite that provide part of the activation energy for the nucleation process. These embryos are visualized to be regions of localized strain in which the atoms in the austenite lattice are displaced part way along the path to their ultimate positions in the martensite. Consequently, it would

Jan 1, 1953

Jan 1, 1946

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division OFFICERS AND COMMITTEES S D Michaelson, President J W Woomer, President-elect Elmer A Jones, Past President C E Lawall, Eastern Regional Vice-President G Donald Emigh, Central Regional Vice-President J D Forrester, Western Regional Vice-president R B Ladoo, Treasurer John Cameron Fox, Secretary

Jan 1, 1958

By Carleton Ellis

The problem of the influence of hot surfaces upon gaseous combustion is one which, from a purely scientific standpoint, has engaged, for many years past, the attention of Prof. William A. Bone, of Leeds University and the Imperial College, London ; and as his recent work has been the direct outcome of earlier scientific investigation, it will be appropriate, by may of introduction, to review briefly the present position of science with respect to this important subject, as stated by Professor Bone. One may perhaps best arrive at an understanding of the term " flameless " or " surface " combustion by considering certain facts which differentiate it from the more familiar processes of

Jan 1, 1913

By K. G. Colman

This text is intended to provide the operator and turn-key contractor with the basic data for sizing vibrating screens to be used in ore crushing plants. The basic capacities, modifying factors, etc. used in the area requirement calculations were developed empirically and modified to their present values based upon years of practical applications. It must be pointed out that screening is much more of an art than an exact science, however, the information presented here should provide for reasonably accurate screen sizing when applied to metallic ores .

Jan 1, 1978

By W. W. Mullins, F. A. Nichols

Solutions are developed, assuming surface diffusion and both internal and external volume diffusion, for the relaxation of bodies slightly perturbed from spherical and cylindrical geometries. Combined with those previously published for the nearly planar case, these results provide a means of gaging the relative contributions of the two diffusional proc-cesses in any given case. It is shown that in all sintering experiments to date, and probably in any attainable in practice, surface diffusion has played the dominant role, although most previous authors have assumed otherwise. It is also shown that surface diffusion predominates in normal field-emission tip blunting and also for the coalescence of gas bubbles introduced into metals by a bombardment. The surface-diffusion solutions for a perturbed sphere are combined with previous results for volume diffusion to show that the inclusion of interface diffusion permits considerably larger spheres to develop in diffusion-controlled precipitate growth before the onset of instability. A mechanism is also proposed for the spheroidization of precipitate platelets as well as rods. In a previous paper1 the relaxation of a nearly plane surface to flatness by the combined action of the transport processes of viscous flow, evaporation-condensation (in a closed system), volume diffusion, and surface diffusion has been analyzed under the assumption that all surface properties are independent of orientation. In this treatment, criteria were developed for deciding which process predominates, and solutions valid in the latter stages of the sintering of small wires and particles to a plane were obtained. A numerical solution, valid throughout the entire particle-sintering process for the case of surface diffusion, was subsequently obtained by the present authors.' It was found that the analytic solution (which assumed small slopes everywhere) is accurate to within -10 pct when the maximum slope of the profile is less than 0.3; the wire-sintering problem has also been solved nu- merically for the case of surface diffusion and here again the results converge to the analytic small-slope solution at late stages of the process, the two solutions agreeing in this case to within 10 pct when the maximum slope of the profile is less than -0.6. The purpose of this paper is to extend the perturbation solutions to nearly spherical and nearly cylindrical geometries. We treat only the two principal diffusional processes, i.e., surface and volume, but for these geometries we discuss volume diffusion both inside and outside of the solid. Our results, when coupled with Mullins' solutions1 for nearly planar surfaces, provide criteria for gaging the relative contributions of surface and volume diffusion to the over-all transport process in three basic geometries. A very interesting feature in the cylindrical case is the occurrence of instability for longitudinal perturbations with wavelengths greater than the cylindrical circumference, a classical result. This instability of the cylindrical surface is applied to give a quantitative explanation for the often-observed "erratic" pore closure in the late stages of the sintering of wire compacts; also, the theory previously presented for the spheroidization of rod-shaped precipitates by surface (interface) diffusion' is expanded now to include volume diffusion inside and outside of the particle. The results for circumferential perturbations on a long cylinder allow quantitative estimates for gaging the relative importance of surface or volume diffusion in the early stages of the sintering of spheres or wires. The results here demonstrate clearly that surface diffusion has played a very important, if not dominant, role in all sintering experiments discussed in the literature, although the surface-diffusion contribution to the kinetics has usually been ignored. The results for the sphere (surface-diffusion case) are added to the results obtained previously by Mullins and sekerka3 concerning instabilities of a growing spherical precipitate particle (with interface diffusion disallowed) to obtain a general solution to this problem including interface diffusion. The inclusion of interface diffusion is found to increase significantly the range of stability of a growing spherical precipitate for typical metallurgical cases. The following assumptions are made: (i) the initial surface lies everywhere near and has a slope differing only slightly from that of the reference

Jan 1, 1965

By Evert Hoek

An empirical criterion is presented for use in estimating the strength of heavily jointed or weathered rock masses. This criterion incorporates the intact strength of the rock material and introduces two dimensionless parameters m and s which characterize the behaviour of the interlocking particles in a jointed rock mass. The use of rock mass classification systems for estimating the values of these parameters is discussed. The application of this non-linear failure criterion to the analysis of slopes is illustrated by means of a worked example.

Jan 1, 1983

By Charles M. Rolker

It is not my purpose to present a complete description, still less a thorough discussion from a theoretical stand-point, of the Leadville ore-deposits. Hence I have given to this paper the more modest name of " Notes;" since it is little more than a record of observations made three or four years ago, and now published from my original memoranda, with the view of preserving the facts rather than of

Jan 1, 1886

By John Treweek

FOR many years the Homestake Mining Co. has devoted serious attention to the elimination of accidents, and ground is steadily being gained in this direction. In accident prevention work it is line-plunging with perfect teamwork and not the spectacular forward pass that brings progress toward the goal. In both surface plants and under- ground workings we regard "good housekeeping" as a first requisite for safety as well as efficiency. Under this term are included all types of safety guards and protective devices as well as cleanliness and orderliness it working places. Perhaps the most important factor in safety work is to arouse and maintain employee interest. The general morale and contentment of employees is of particular importance.

Jan 1, 1938

Jan 1, 1920

By M. Tsunekawa, T. Takamori, T. Hirajima

In spherical agglomeration in water, the pattern of the growth behaviour of agglomerates is essentially determined by the surface chemical properties of the particles and the oil-water interface. When particles are suitably hydrophobic and oil-water interfacial tension is not too low under an adequate condition for agglomeration, large agglomerates are formed in the initial stage and micro- agglomerates do not appear. When particles are poorly wetted by oil and the interfacial tension is low, initially micro-agglomerates are formed and, after certain aging time, they grow to large agglomerates in a relatively short time without formation of intermediate size agglomerates. Under adequate conditions, the amount of oil and power input do not produce any remarkable effect on the pattern of growth.

Jan 1, 1980

By M. P. Board, M. J. Reus

Instrumentation was installed during construction of the Silver Shaft in northern Idaho to evaluate lining behavior and rock deformation. Rock mass displacements were monitored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gages. Rock displacement data from the 5,955-ft level indicate rock mass anisotropy. Liner stress and strain data reflect high in situ stresses and nearby station and raise construction. Continued monitoring and preliminary analysis indicate that concrete-lined, circular shafts are stable for high, unequal stress fields and anisotropy in deep level mines.

Jan 1, 1984

By Fred M. Phillips

Jan 1, 1985

By L. Massé, Th. Koulomzine

Note on Haalck's Formula Quantitative interpretation of magnetic anomalies is admittedly a difficult process. Few authors have attempted a general approach to this problem. A number of publications can be found widely scattered through scientific periodicals, which present particular solutions obtained by the introduction of simplifying assumptions, such as the reduction to an equivalent magnet or pole, or the hypothesis of a very thin vein. The practical applications of these solutions are necessarily very restricted though they have given satisfactory results in isolated cases. Probably the most widely known equation of this type was given by Haalck.' His classic work contains curves calculated for typical conditions, and has now become a standard reference. However, a close scrutiny of Haalck's derivation reveals that, aside from the hypothesis of a thin vein, it rests on the

Jan 1, 1949

By Robert W. Bartlett

A computer model for predicting the rate of oxidative leaching of copper from fragmented low grade sulfide ores is presented. The model involves the kinetics of the dissolution of chalcopyrite grains and solution diffusion of oxygen within rock pores. Adjustable curve fitting parameters are not used. The model was tested by comparing computed extraction curves with experimental results for a -11 inch ore obtained by block caving and leached at 90°C and 400 psi oxygen for one year at the Lawrence Livermore Laboratories.

Jan 1, 1973

By L. A. Adorjan

The tensile strength of agglomerate models due to capillary forces has been determined by computation of the exact surface profiles. Graphs showing tensile strength as a function of moisture content and contact angle me given for spheres in cubic arrangement. Another model of cones attached to cube faces, in cubic packing, provides a better representation of angular particle agglomerates. An algebraic formula approximating tensile strength as dependent on surface tension, particle size, moisture content, contact and cone angles was developed. The phenomenon of "capillary evaporation" due to high negative capillary pressures is explained and its influence on tensile strength of agglomerates is evaluated.

Jan 1, 1977

By William A. Prichard

After a study of the excellent geological reports and maps prepared by the United States Geological Survey,? and after practical experience in working the ore-deposits in this field,

Jan 1, 1904

Jan 1, 1914

By F. D. Rosi, Walter R. Hibbard, R. I. Herron, H. T. Clark, O&apos

Introduction and Previous Work In the search to find a copper-base alloy with high strength properties, it was considered that the addition of a small amount of an age-hardening element to a binary system with useful strength properties might result in a series of alloys of theeretical and practical importance. The copper-nickel system was selected for its basic properties and chromium was added as the age-hardening element in view of the small percentage involved and its decreasing solubility with decreasing temperature. A study of the Cu-Cr binary alloys was undertaken as a preliminary investigation. However, in view of the response of these alloys to heat treatment, the scope of this phase of the investigation was widened.

Jan 1, 1949