Search Documents

By V. R. Garfias, A. C. Fernandez

Despite artificial curtailment in all the fields of Mexico during 1937, owing to strikes and other disturbances, the production of crude petroleum aggregated approximately 46,738,000 bbl., showing a substantial increase of about 5,571,000 bbl. over the preceding year. Most of this increase occurred in the Poza Rica area, where, although only two wells were completed during the year, production increased from 14,162,000 bbl. in 1936 to 18,634,000 in 1937. While production in the South fields (Golden Lane) remained practically stationary, the output in the heavy-oil district of the Northern fields showed an increase of 1,930,000 bbl., because production had been considerably curtailed during 1936. Production in the Isthmus of Tehuantepec decreased about 596,000 bbl., owing to labor disturbances. Crude run to stills in local refineries increased from 34,000,000 bbl. in 1936 to 36,650,000 in 1937. Exports of crude and refined products were approximately 22,700,000 bbl., or 500,000 bbl. less than in 1936. Domestic consumption, excluding ships bunkers, reached a total of 20,000,000 bbl., which shows a small increase of 200,000 bbl. over the. previous year. Domestic demand for gasoline is estimated at 3,400,000 bbl. for the year, which represents an increase of 500,000 bbl. over 1936. In all, 60 wells were completed in Mexico during 1937, as compared to 70 in 1936 and 74 in 1935. In proven areas 52 completions resulted in 25 producers and 27 failures. In the Northeastern area near the United States border, five gas wells were drilled, all of which were producers; one of them, in Camargo, came in with a daily production of 20,000,000 cu. ft. of gas. One well, resulting in a failure, was drilled in Las Uvas, Coahuila, and three wells were completed in Quebrache, to the southeast of the heavy-oil district, resulting in two small producers and one failure. TWO more wells drilled in San SebastiBn, east of the Golden Lane, were failures. Fields Northern Fields (Heavy-oil District).—A total of 11 producers and 22 failures was completed in the proven areas of the Northern fields, as compared to 16 producers and 25 failures in 1936. In the Altamira

Jan 1, 1938

By C. Z. Serpan, L. J. Wittenberg

The density of liquid plutonium was determined, by a pycnometm'c technique, from 664 to 788°C and exhibited a temperature dependence, which could be expressed as:. P= C17.63 - 1.52 x 10-"t] +0.04 g per cc where t = OC. These density values compare favorably with the values previously obtained by a technique utilizing Archimedes' principle. The apparatus and method were evaluated when the densities 0.f molten tin and bismuth were measured and found to be in agreement with accepted literature values. PLUTONIUM or an alloy of plutonium in the liquid state has been proposed as a fuel for a fast-breeder type nuclear power plant.' Since knowledge of the liquid density of plutonium is required for the proper design of such a system, this study was undertaken. In addition, the density and volume expansion coefficient of liquid plutonium are of interest for comparison with these same properties of the six allotropic modifications of the solid metal. Comstock and GibneyZ were first to report a value for the density of liquid plutonium. The value for only one temperature, 665"C, was calculated from data obtained by the radiography of the meniscus, Fig. 3. Recently, the density at a series of temperatures has been reported by Knight,3 who obtained his values by using a differential volumeter, and by 01-sen, Sandenaw, and Herrik, who obtained their values from measurements of the loss in weight of a tungsten bob immersed in the liquid. The density of liquid plutonium reported here was determined by a vacuum pycnometer method. In an evacuated system, the tips of calibrated tantalum pycnometers were lowered beneath the liquid sur-

Jan 1, 1962

By Francis Crockard

DURING the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of stream-lined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other indus-tries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phos-phorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater impor-tance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appear-ance, having found that the analysis alone is an insufficient guide to their requirements.

Jan 1, 1936

By F. L. Bosqui

NO metallurgical process developed in the last half century has been more widely advertised to both technologists and lay- men, or has done more to promote efficiency and economy in the extraction of the valuable portions of ores than has the flotation process. Practically everybody has heard of this strange procedure whereby the heavy portions of an ore are made to float while the light parts sink. Some- times it is called froth flotation, the mineral-bearing froth being from the first a distinguishing characteristic. Many times it is called oil flotation, because a thin film of oil was commonly applied to the particles to be floated to make them adhere to the bubbles that rise through the pulp to form the surface froth. Oil, though commonly used, is not, however, necessary for this purpose, which is one of the facts that has been learned as the process has been developed.

Jan 1, 1940

By R. D. Vaughn

The limiting cases of non- Newtonian fluids flowing inside a concentric annular duct are developed without using a model of the fluid behavior. The solutions provide limits with which to test the various models of fluid behavior such as the power law and Bingham plastic models. The results of previous theoretical work are discussed in terms of limiting cases. This limiting case study also shows that experimental work on flow of non-Newtonian fluids in annular ducts should be confined to ducts for which the ratio of the radius of the inner wall to that of the outer wall is less than 0.3 and preferably less than 0.2. INTRODUCTION During the last 10 years the problem of laminar flow of non-Newtonian fluids in concentric annuli has received much attention large1y because of its application to the hydrodynamics of the wellbore. Recently solutions utilizing the power law1,2 and Bingham plasticl,3,4 models have been published. In this paper the method of limiting cases, which has been successfully applied to laminar-flow heat transfer516 will be applied to the problem of flow of non-time dependent, non-Newtonian fluids through annuli. This method permits solutions for the limiting cases to be made without using a model of unknown validity. The solutions, therefore, provide limits with which to test the various models which have been or will be proposed. A pertinent conclusion concerning the region of experimental work is also provided. DEVELOPMENT OF LIMITING CASES The limiting cases for the axial flow of fluids in concentric annuli may be defined with reference to Fig. 1. It is possible to define two limiting cases which pertain to the physical dimensions of the annulus. First, the annulus must degenerate to a circular pipe as the radius of the inner wall decreases or, as k = (k R/R) ? 0. Second, the annulus must approach the limit of parallel plates of infinite extent as the spacing between the inner and outer tubes becomes small in comparison with the radius R of the annulus, or as k?1. It is also possible to ascertain three limiting cases which pertain to fluid behavior. With reference to Fig. 2, as a fluid becomes progressively more pseudoplastic, the shear stress-shear rate relationship progressively approaches the indicated horizontal line more closely. At this limit the shear stress becomes independent of the shear rate. At the other extreme of increasingly dilatant behavior, the vertical asymptote is approached. Intermediate between these two limiting cases lies the case of the Newtonian fluid. Fluids which exhibit a yield shear stress also approach the limiting case of "infinite" pseudoplastic behavior. The remainder of the theoretical development is concerned with the description of and the solutions

By T. E. Leontis, J. P. Murphy

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By J. P. Murphy, T. E. Leontis

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By W. C. Ellis, M. E. Fine

In the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;' the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition2 which has a large effect on other properties. The thermal expansion data for the system have been reported only from room temperature to 100 C and for this temperature range a minimum in coefticient in the rcgion of 50 at. pct cobalt is well established.3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the tcrrelation. Experimental Procedure The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 5c pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 1/2 in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for I hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,? the differential expausion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outcr silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested On a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A nonoxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1949

By R. O. Williams

Measurements have been made of the internal energy of deformation in a Cu-A1 alloy and a Cu-Zn alloy as the deference between the work and the released heat. The method required the rapid compression of samples to reduce thermal interactions. The rate of energy storage is low initially but then becomes almost linear with strain. Both alloys stored about 60 cal per mole at a strain of 0.4 in the recrystallized condition. The fractional rate of storage increases at low strains reaching about 0.25 at a strain of 0.15 and then decreases slowly with increasing strains. As do pure metals, these alloys release appreciable energy immediately following deformation; in contrast with pure metals, however, the release continued for extended periods of time. This energy release is somewhat sensitive to the amount of deformation, the deformation temperature, and prior thermal & eatment. It is believed that this release is a composite of that observed in pure metals which has been attributed to dislocations and that due to the motion of vacancies which produces increased short-range order. IT is expected that changes brought about by deformation of a pure metal can be understood in terms of the three defects—dislocations, vacancies, and interstitials—along with the interactions possible between these defects. Frequently stacking faults are created and must also be considered. 1t is not immediately clear whether or not the stress fields which are created should be regarded as independent of dislocations. For alloys there is the important additional effect of atomic configuration, for example short-range order, which must also be considered and will, in general, interact with each of the above defects. While it is true that a complete understanding of pure metals is not yet possible, it would seem very valuable to establish the similarities and differences between pure metals and alloys. Such knowledge could contribute to the understanding of both. A study of the changes in internal energy resulting from deformation of two alloys is reported here. Although some information has been available for alloys almost as long as for pure metals, the volume of work has been substantially less. Sato' and Quinney and Taylor' were responsible for the earlier work, both using brass and annealing calorimetry. tizhnova' studied stored energy in Cu-Ni alloys by a method somewhat similar to the one reported here. Bever and his co-workers have made extensive studies of Au-Ag alloys4'5 and more recently CU-AU'U' using solution calorimetry. Clarebrough et a1.' have recently studied brass using annealing calorimetry. EXPERIMENTAL METHOD The present results were obtained by the rapid, adiabatic compression of a sample about 1/4 in, diam by 1/2 in. long between two tungsten carbide hammers. A vacuum provided thermal isolation and oil provided effective lubrication between the sample and hammers. The increase in internal energy is the difference between the mechanical energy and the heat liberated within the sample. The mechanical energy was determined from the velocity of the hammers (calculated from the height through which the hammers traveled) and was essentially constant for each deformation cycle. The heat was determined from the temperature increase of the sample which was measured by an embedded thermocouple. Specific heat data were calculated from Neumann's rule using tabulated data for pure metals.9 Since the fraction of the energy which is stored is large compared to that for pure metals, specific heat data of high accuracy are not required. Successive increments of deformation were carried out by repeating the procedure, the limit being determined mostly by the decreasing accuracy caused by the increasing corrections and the decreasing storage of energy. About five cycles were used to give a true strain of about 0.5 while the time interval between cycles was 1 to 2hr.

Jan 1, 1963

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low, a medium, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0% ash, as follows: from low-volatile anthracite, 0.7%; from medium-volatile coal, 1.0%; and from high-volatile coal, 2.3%. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0% or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a convc.ntiona1 dense-media washing plant. Anthracite preparation practices during much of the industry's history were geared to maximum recovery of the larger sizes, pea through egg, which were used in hand-fired, domestic furnaces. Those sizes were cleaned to meet trade requirements, and the smaller sizes were usually higher in ash content. The impression, thus, was that ash content of anthracite always increased as the sizes got smaller. It was presumed that it was impossible to wash the finer sizes to extremely low ash contents. Following World War 11, the classical domestic market began to decline and the finer sizes assumed an increasingly large share of the market. For example, in 1949l 61% of the production was still pea and larger. Fig. l2 shows that -by 1955 these sizes accounted for only 50%, and in 1965, they were only 39% of the total anthracite produced. With the reduction in the market, increased quality was demanded, especially in export markets, and an increasing number of dense-media magnetite washers were installed in new and existing cleaning plants. In 1965, the coarse coal prepared at 59 breakers in the anthracite fields was sampled by the U.S. Bureau of Mines (USBM); approximately 50% of these plants were equipped with dense-media magnetite washers.3 Since 1950, more attention has been focused on the use of finer sizes for numerous industrial uses, including iron-ore sintering, pelletizing, foundry coke-making, cement manufacture, production of calcium carbide, and of carbon electrodes, etc. Most industrial uses require relatively clean anthracite, such as 10 to 11% ash for sintering and foundry coke, 7% for aluminum melting-pot cathode carbon, and 5% for carbide production. Hence, cleaning methods have been improved to the extent that dense-media washers, hydraulic cyclones, and flotation cells have been introduced as fine-coal-cleaning devices. It is now possible to wash the buckwheat, rice, and barley sizes (9116 X 3132-in.) to ash contents as low as 8 to 10% in dense-media devices, but washing the -3132-in. sizes to those limits presents more difficult problems, due mainly to the fineness of the material. This USBM investigation was conducted to determine the amount and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. The goal was to reduce the ash content to a level acceptable for industrial carbon uses, including electrode manufacture, which generally requires an ash content of 1% or less. While low-ash content is of primary importance in selecting industrial carbons, the amounts of other constituents are also important, including iron, silicon, titanium, nickel, vanadium, and sulfur. They were not considered in this work, since their occurrence in deashed anthracite has been studied elsewhere.4 The results of the present investigation were used to design a flowsheet, suggesting a method for producing ultraclean anthracite as part of conventional preparation practice, using dense-media vessels, crushers, pulverizers,

Jan 1, 1970

By I. R. Kramer, H. Shen, S. E. Podlaseck

The tensile and creep properties of aluminum in vacuum have been investigated. It was found that the general effect of a vacuum environment was to reduce the rate of work hardening. Results obtained from creep tests showed that lowering the test pressure from 2 x 10-4 to 10-7 torr produced a decrease in the activation energy as much as 500 cal per mole. An attempt is made to explain these effects in terms of how the surface-stress field of a specimen may be affected by a vacuum environment during plastic deformation. In a previous paper,' the results were reported of some of our early work on the effect of vacuum environment on the stress-strain curve of aluminum single crystals. This effort has been extended to the studies of the tensile and creep properties in vacuum as a function of various metallurgical parameters. Some of the recent surface-effect studies2'3 have revealed that a region of high dislocation density, the so-called "debris" layer, is formed near the surface of the specimen as a result of plastic deformation. This layer acts as a surface barrier to oppose dislocation movement. The strength of this barrier depends on the surface condition such as oxidation or surface removal. Experimental results obtained from surface-removal work2, 3 indicate that such a surface barrier, which may be characterized by a stress field, affects the applied stress and the rate of work hardening. In the case of aluminum, this stress field was found to be directly proportional to the strain and the strain rate; however, the slope of this curve is independent of orientation of the crystal and may be altered by using different surface treatment. Since the escape of dislocations may be retarded by the presence of an oxide on the surface of a specimen, it is expected that a change in the rate of oxidation in vacuum will affect the process of dislocation accumulation in the debris layer. Consequently, it also affects the plastic behavior of a metal. This paper reports the changes in some of the creep and tensile properties of aluminum in vacuum and discussions of the observed effects in terms of the concept of the "debris" layer. EXPERIMENTAL PROCEDURE Tensile Tests. A sketch of the tensile apparatus is given in Fig. 1. This apparatus was contained in a bell jar (14 in. diam by 24 in. high) connected to a 10-in. vacuum system. The load was applied to the specimen by means of a gear train which was driven by a magnetic clutch located outside the vacuum chamber. The specimen, held by a pair of square shoulder grips, was attached to the load cell at the top and the drive gear at the bottom. A displacement transducer was placed between the two grips as shown in the figure to measure the elongation. Signals of elongation and load were amplified and recorded on an X-Y recorder. The system was capable of detecting loads as small as 0.025 lb and displacements of 0.0002 in. Shoulder-grip specimens of aluminum single crystals, having a nominal square cross section of 1/8 by 1/8 in. and a 3-1/2-in, gage length, were grown by the Bridgeman techniques. The original purity was 99.997 pet. The orientations of the crystals investigated are shown in Fig. 4(a). The crystals were annealed at 600°C for 2-1/2 hr, electropolished, and placed in the vacuum test chamber without any delay. All the crystals were deformed at a strain rate of 4 x 10-5 sec-1 at 24o ± 3°C. A study was made to find whether a chemically passive surface film would give the same effect as a vacuum environment. Specimens of aluminum 1100 (0.187 in. diam with a grain size of 0.1 mm)

Jan 1, 1965

By E. P. Klier, Jane Jellison

The course of the transformations on cooling in a series of Cu-A1 alloys has been followed by means of thermal analysis, X-ray diffraction, and optical metallogrAphy. Specimen size was found to have a pronounced effect on the time of completion of the pearlite transformation due to modification in the unmber of nuclei. The ordeving transformation zvas observed for all cooling rates for all alloys studied, and is considered insuppvessible. At intermediate cooling' rates, a transitional struchire for 011 alloy compositions and based ox the bainite reaction was observed. The alloys of aluminum and copper possess a eu-tectoidal region at from about 9.4 to 16 pct Al. Above the critical temperature, the disordered bcc phase, 0, is stable. At subcritical temperatures, the 0 phase decomposes under equilibrium conditions into the stable phases, a and y,. At the eutectoid composition, these phases develop a lamellar pearlite structure, in appearance much like that found in steels. During rapid quenching from supercritical temperatures, the diffusion processes required for the formation of the equilibrium phases are suppressed, and the 0 transforms to an acicular martensitic phase, designated B or y' depending on the aluminum content, or to a mixture of the two. Early investigators of this system concentrated on determining the equilibrium phase diagram, ''' the structure of the equilibrium phases,3 and later the isothermal decomposition of the 0 phase at subcritical temperatures, or the decomposition of the martensite on tempering. Other work which treated the nonequilibrium transformations concentrated largely on the martensite transformations and the structure of the b and y' phases.15"17 Since the pearlite and martensite transformations in this system resemble those in steels, the one being formed by nucleation and growth of adjacent lamellae of the equilibrium phases, and the other by a diffusionless, shear-type transformation, the present study has been undertaken to investigate the structures formed on continuous cooling, with the objective of constructing cooling transformation diagrams analogous to those derived for alloy steel systems. In particular it was desired to determine whether parallels between the A1-Cu and iron-iron carbide systems on continuous cooling extended to encompass the intermediate phase, namely the bainite structures, which form by a combined martensitic-diffusion mechanism,'' but which are supersaturated with respect to the equilibrium phase upon which their crystal structure is based. To this end the transformations in representative alloys of the Cu-A1 B eutectoid system have been followed, using the methods of thermal analysis, X-ray diffraction, and optical microscopy. EXPERIMENTAL PROCEDURE Materials. The materials tested were those used by Klier and Grmko 5 in their study of the isothermal decomposition of these alloys. The alloys were melted in graphite crucibles and chill-cast into 5 by 2 by 1/4 in. ingots. The ingots were then hot-rolled to sheets 1/8, 1/16, and 1/32 in. thick. The compositions are given in Table I. Specimen Preparation. Specimens for thermal analysis were in the form of small squares approximately 1/4 in. on a side. For the 11.9 and 13.5 Al-Cu alloys, the sheet thickness was 1/16 in. and for the 10.5 A1-Cu alloy the 1/32-in. sheet was used. One lead of a chromel-alumel thermocouple was spot-welded to either face of the square with the specimen itself thus forming the hot junction of the thermocouple. Specimens for X-ray analysis were prepared as filings from martensitic sheet stock and were sealed in glass ampoules under 1/2 atm of argon. Metallographic examination of the powder specimens was carried out on a portion of the heat-treated filings mounted in lucite. All specimens were examined metallographic ally after etching

Jan 1, 1965

By Nicholas J. Grant, Robert H. Kane, Bill C. Geissen

The platinum-rich section of the Ta-Pt Phase diagram was worked out by metallographic and X-ray techniques, using twenty alloys; solidus temperatures and solid solubilities were determined. Besides s phase, four intermediate stoi-chiometric phases were found: TaPt (high-temperatzrre phase, structure unknown); TaPt2 (ortho-rhomhic, new type); a TaPt3 (orthorhombic, TiCu3 type); ß TaPf3 (monoclinic, new type). TaPt2 and TaPt3 melt congmentlv; two eutectic, two beritec-tic, and one eutectoid reactions occur in the inuestigated range. THE Ta-Pt system was examined as part of a study of the phase diagrams and the intermediate phases of niobium and tantalum with Group VIII transition metals. Since the main scope of this work was the relation among the ordered close-packed phases occurring in the concentration range from AB to AB3 (A = Nb, Ta; B = Pd, Pt, and so forth), only the platinum-rich side of the diagram was worked out thoroughly, while spot checks were made to determine the approximate outline of the tantalum-rich portion. The system has not been thoroughly treated in the literature; Greenfield and Beck1 in their survey of refractory metal intermediate phases found a o phase between -18 and 37 at. pct Pt which coexists at higher platinum concentrations with an unidentified intermediate phase. Browning2 worked on the range between 55 and 100 at. pct Pt; however, this preliminary study did not cover temperatures >1500°C, and included no conclusive crystallo-graphic data. More recently, a study of the platinum-rich section of the Ta-Pt system has been carried out by Ray,3 while Hartley, Parsons, and steedly4 have studied the tantalum-rich section. The crystal structures of TaPt2, a TaPt3, ß TaPt3, and others have been reported in abstracted form by Giessen and Grant.5 EXPERIMENTAL METHODS The methods of alloy preparation and processing and of the metallographic and X-ray procedures follow very closely those described by Ritter, Giessen, and rant' for other refractory metal-noble metal systems, and will not be repeated except where significant differences exist. Starting materials were: tantalum rod of 99.95 pct purity, supplied by National Research Corp., and platinum sponge 99.9 pct, supplied by The International Nickel Co. An oxygen analysis of the tantalum rod showed 30 ppm O; other impurities were C, N, Si, Nb, Mo, none of these exceeding 50 ppm, and 100 ppm W. Homogeneous buttons were readily prepared as follows: ingots of 5 g were weighed and arc-melted under welding grade argon, followed by two remelts after inverting the button. Between 40 and 100 at. pct Pt, weight losses during the first melt rarely exceeded 0.1 pct, in which case the alloy was rejected, and were nil on subsequent remelts. Since the vapor pressure of platinum far exceeds that of tantalum, the small evaporation loss could be assumed to consist of platinum; therefore, a corresponding amount of platinum was added on the second melt. Since it was confirmed on pure tantalum samples that no weight gain through oxygen or impurity pickup occurs (see Ref. 71, it could be assumed that the uncertainty in the composition did not exceed ±0.1 at. pct for the range 40 to 100 at. pct Pt. For the four control melts from 0 to 40 at. pct Pt, an error of ±0.5 at. pct was calculated. Microscopic examination of the whole buttons after melting showed no inhomogeneity other than local coring. This was eliminated by a homogenization heat treatment. A total of twenty-three alloys were prepared. Heat treatments were carried out in a tantalum

Jan 1, 1965

By R. H. Frazier, C. H. Lorig, F. W. Boulger

THERE are both advantages and disadvantages in using semikilled steels in place of killed steels. One advantage of semikilled steels is they provide a higher ingot-to-product yield. This is especially important to shipbuilders in the time of national emergency. By using semikilled steel for hull plates, a greater number of ships can be built from the same ingot tonnage. Consequently, if semikilled steel plates are adequate for the service, the advantage of the higher product yield is of considerable importance. The performance of hull plates is closely associated with the ductile-to-brittle transition temperature, and this, in turn, is strongly dependent on the composition of the steel. A low transition temperature is desirable because it indicates that the steel is less likely to fail at low ambient temperatures. Killed steels are known to have lower transition temperatures than semikilled steels. It is believed that the better qualities of killed steels in this respect are due mainly to the low oxygen contents of the steel. The principal deoxidizers, aluminum, silicon, and manganese, lower the oxygen content. Fundamental studies1-0 have shown that the oxygen content remaining after the addition of one of these three elements is influenced by the residual amounts of the other two present. In the current study, therefore, various amounts of silicon and aluminum were added to steels containing different manganese contents for the purpose of studying the influence of silicon and aluminum on the notched-bar properties of hot-rolled steels. Eleven types of steels were studied. The temperature at which the plates were finish-rolled was care- fully controlled at 1850°F. All plates were rolled to ¾-in. thickness, and tested in the as-rolled condition. The total number of steels prepared in the laboratory for this study was 95. The charge consisting of ingot iron and ferrosilicon equivalent to 0.10 pct Si was melted in a 200-lb induction furnace under an atmosphere of argon to insure low, uniform nitrogen contents. After the charge was melted and the desired temperature was obtained, the melt was partly deoxidized with either silicomanganese or aluminum. Aluminum was used for this purpose in only those steels with very low silicon contents, where the finished steel was to contain some aluminum. This initial deoxidizing addition was made to obtain consistent recoveries of subsequent additions of ferro-manganese, ferrosilicon, and aluminum. Carbon, in the form of graphite, was added, either just prior to tap or to the final aluminum addition. The entire heat of 200 lb was poured directly into a 6x6-in. big-end-up mold. The ingots of semikilled steel were capped with a steel plate. The killed steels, on the other hand, were poured with a hot-top containing 14 pct of the total volume of the ingot. The ingots were processed by heating to 2250°F, followed by forging to slabs 1¾ in. thick and 6 in. wide. After reheating to 2250°F, the slabs were rolled to 0.9-in. gage, using reductions of approximately 1/6 in. per pass. The 0.9-in. thick plates were immediately recharged in a furnace held at 1850°F. After 30 min in the furnace at 1850°F, the plates were rolled to ¾ in. in one pass. Following the final pass, the plates were stacked on edge on a brick floor, with a brick separating one from another, where they were allowed to cool in air. Drillings for chemical analysis were taken from the plates at locations corresponding to the top and bottom of each ingot. Carbon, manganese, silicon, phosphorus, sulfur, and nitrogen contents of each sample were determined. The analysis of each steel was carefully controlled so that the contents of

Jan 1, 1957

By F. D. Rosi

The slip and twinning behavior in extended titanium crystals were studied in some detail. The formation and appearance of coarse kink bands are discussed. Their crystallographic geometry was determined by X-ray analysis. A phenomenological interpretation of the complexities in kink band development is also presented. The critical resolved shear stress, coefficient of shear hardening, and plane of fracture were determined for several crystals extended at room temperature. THE slip and twinning elements observed in the room-temperature deformation of titanium were enumerated in a previous paper1 in which considerations were advanced regarding the nature and selection of these elements and their effect on the known mechanical properties of this metal. The present study concerns the crystallographic, microscopic, and mechanical aspects of flow in relation to the slip and twinning elements, and includes a prediction of slip systems, nature of slip and twin markings, inhomogeneities of plastic flow, and stress-strain characteristics. Unless otherwise noted, arc-melted titanium sponge (99.77 pct) was used in these experiments. The method of production of crystals, their dimensions, and the surface preparation for micrographic examination have been reported.&apos; For obtaining stress-strain characteristics, only those crystals which traversed the entire width of the specimen and were at least 8 mm in length were used. Tensile deformation of the crystals was performed with conventional grips for sheet specimens and a constant-stress loading beam, designed after the method of Andrade and Chalmers.&apos; The specimens were loaded by allowing sand to flow from a reservoir into a bucket suspended from the longer end of a balanced 6:1 lever arm at a rate controlled to load the specimen approximately 2 kg per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire strain gage, Type A-8, which permitted a reading accuracy of 2 microinches per inch. The formulas used in the evaluation of shear stress and shear strain, as in deriving the coefficient of shear hardening, are given by Schmid and Boasv n terms of the original orientation and change in length of the crystal. For calculating the critical resolved shear stress, the standard equation was used. The crystallographic nature of the unpredictable slip observed in a number of specimens was determined by the single-surface X-ray method of analysis as described in ref. 1. Experimental Results Prediction of Slip System: It was reported&apos; that room temperature slip in titanium takes place predominantly on {10i0} and in a <1120> direction, giving three potential slip systems. Hence, it should be possible to predict the operative primary system in the manner used by Taylor and Elam&apos; for alu- minum (i.e., the one with the greatest component of shear stress in the direction of slip). The stereo-graphic construction in Fig. 1 shows that this is true. In all cases, slip was found to occur initially on the (0110) plane and, in a number of cases, in the [21f0] direction. (The direction of slip was not determined for all orientations.) It follows that duplex slip can be expected when two slip systems are geometrically equally favorable for slip, as demonstrated in Fig. 2. In both crystals slip took place simultaneously on the (1700) and (olio) prismatic planes, as indicated by Fig. 2a and b. In the case of crystal B the movement of the specimen axis with increasing extension was toward the (10i0) direction, which represents the stable end orientation resulting from alternate slip on the [2ii0] and [1120] directions. This is analogous to the duplex slip process in face-centered cubic metals." Unpredictable Slip: In a number of crystals whose orientations were well within the operation of a single slip system, secondary slip occurred on planes not predicted by the criterion of maximum shear stress. Examples are shown in Fig. 3. In addition to

Jan 1, 1955

By M. Ahlers, Horace Pops

Slip features and formation of stress-induced mm-tensite have been studied in single crystals of fl phase Cu-Zn alloys in the composition range between 43 and 48 at. pct Zn. A phenomenological analysis is presented in which the glide planes and directions that me associated with the inhomogeneous shear in the martensite phase are predicted from the experimentally determined habit planes and macroscopic shear directions. It is shozun that the resolved shew component of the applied stress on the secondary shew system is a very important factor governing the formation of stress-induced martensite. A comparison is made between martensitic phases that form spontaneously upon cooling and those phases that arise from deformation. THE ß phase in Cu-Zn alloys is unstable and may transform spontaneously by a martensitic transformation1-3 during cooling. Thermoelastic and burst-type spontaneous martensitic phases have been observed3 in the composition range between 38 and 42 at. pct Zn. Martensite forms in alloys containing more than 42 at. pct Zn only by cold work below a temperature denoted as Md.4 Thus, alloys near the equiatomic composition can undergo a stress-induced transformation upon cold work at room temperature. Although data have been obtained concerning the effect of temperature5 and composition4 on the deformation of polycrystalline Cu-Zn alloys, it is rather surprising that few detailed studies6-8 on 6 brass have been conducted for single crystals where the stresses acting on crystallographic planes can be determined. A thorough understanding of transformation mechanisms requires knowledge of the role of stress and plastic strain. With this objective in mind we have made an investigation of the stress-induced rnartensite transformation in single crystals of 0 brass in the composition range between 43 and 48 at. pct Zn. Particular emphasis is given to the morphology and crystallographic features and a comparison is made between stress-induced and spontaneous martensite. I) EXPERIMENTAL PROCEDURE Master alloys having nominal zinc contents of 43, 45, and 48 at. pct were prepared from spectroscop-ically pure metals (>99.999 pct) in sealed quartz tubes under a partial pressure of helium. These alloys were cut into several pieces and converted into small rods by melting in quartz tubes. Subsequently, single crystals were grown from the rods by the Bridgman technique and homogenized for 3 hr at 820°C. Lattice parameter measurements were made from stress- relieved filings. Compositions, as determined from the reported variation of lattice parameter with atomic percent zinc,&apos; indicated a zinc loss of less than approximately 0.25 at. pct. The single crystals were electroturned using a phosphoric acid electrolyte into tensile specimens each with a center section of 1 mm diam and 1 cm gage length. Cylindrical specimens approximately 3 mm in diam and 10 mm long and spark-machined rectangular blocks approximately 3 by 3 by 10 mm were prepared for compression studies. These blocks were stress-relieved and electropolished to eliminate any stresses introduced by spark machining. Crystal orientations were determined to an accuracy of ±2 deg primarily from back-reflection Laue photographs, and sometimes by the rotating single-crystal method. Figs. 1 to 3 show the location of the tension and compression axes within unit stereographic triangles. All specimens were deformed plastically at room temperature using an Instron machine, the crosshead speed being 0.02 or 0.05 cm per min. A hard steel hemisphere was placed at the upper end of the compression samples to achieve uniaxial loading. Trace normals of slip markings and habit planes of strain-induced martensite were determined to an accuracy of ±4 deg from the rectangular blocks by a two-surface analysis and from cylindrical specimens by measuring the angle between the tensile (or compression) axis and the tangent to the surface trace for different rotations about the deformation axis. Slip

Jan 1, 1969

By G. R. Speich, S. A. Kulin

The isothermal formation of martensite at subzero temperatures has been studied in an austenitic stainless steel. The amount of martensite formed isothermally in a given time was found to follow a C-curve behavior with decreasing temperature. Since isothermal rnartensitic transformation occurs at temperatures above the true M. temperature of the olloy, the observed M. temperature is dependent on the cooling rate. It is believed that a general martensite theory must include the basic concepts of the strain embryo theory, and also the important role of thermal fluctuations. UNTIL recently the isothermal component of the martensitic transformation had been considered as a trivial effect in theoretical considerations of this type of transformation. One of the postulates used in defining a martensitic transformation was that the reaction was temperature dependent but not time dependent. Cohen and his associates1&apos;2 were the first to report the isothermal formation of mar-tensite. They obsel-ved the time dependency of the martensite reaction at room temperature in plain carbon steels and certain tool steels. They found that a small amount of additional transformation occurred after the specimen reached the quenching temperature and that the rate of this isothermal transformation decreased rapidly with time. These authors considered this phenomenon to be a "tailing-off" of the main athermal reaction. Kurdjumov and MaksimovaL 5 studied the isothermal formation of martensite at subatmospheric temperatures in steels containing 0.6 pct C-6 pct Mn, 1.6 pct C, and in an iron-base alloy containing 23 pct Ni and 3.4 pct Mn. In each case it was found that both the initial rate and the total amount of isothermal transformation exhibited sharp maxima with decreasing temperature. They stated that it was possible to completely suppress the martensitic transformation in the 0.6 pct C-6 pct Mn steel by drastic quenching in liquid nitrogen. They interpreted their results in terms of a thermally activated process. The maximum in the rate of nucleation vs. temperature curve was assumed to be a result of the temperature dependence of the rate of growth of the martensite plates. It has been demonstrated," however, that martensite plates can form with great rapidity even at temperatures approaching absolute zero. In addition," attempts to confirm the reported suppression of the martensitic transformation by rapid cooling of a 0.6 pct C-6 pct Mn steel have proved unsuccessful. On this basis, and on other theoretical grounds, the validity of some of Kurd-jumov&apos;s results and conclusions is open to serious question. Cohen, Machlin, and Paranjpe&apos; have proposed a theory of martensite formation based on the nucleation of strain embryos and a growth mechanism involving cooperative atomic displacements. According to this theory thermal fluctuations can make a strain embryo supercritical and thereby produce martensite isothermally. Das Gupta and Lement&apos; have investigated the isothermal formation of martensite in a 17 pct Cr-0.7 pct C steel at temperatures below the ambient. They found that partial suppression of the martensitic reaction occurred on quenching into liquid nitrogen. That part of the reaction which can be suppressed is taken to correspond to the isothermal rather than the athermal part of the rnartensitic transformation. The initial rate of isothermal transformation for this steel was found to go through a maximum with decreasing temperature. This is in conformity with the findings of Kurdjumov and Maksimova for the steels used in their investigation. Das Gupta and Lement conclude that isothermal martensite formation occurs by the nucleation of new plates and is always preceded by some athermal transformation. An iron-base alloy containing 14 pct Cr-9 pct Ni was used in this investigation to study further the kinetics of the austenite to martensite transforma-

Jan 1, 1953

By Maurice Lacasse, Pierre Legast

GENERAL OUTLINE For more than one hundred years, asbestos ore has been mined on Les Mines d’Amiante Bell&apos;s property at Thetford-Mines , Quebec, Canada. In 1878, the first tons of fibre were produced. The mine operated as an open pit until 1951 at a yearly production of about 330 000 mt of ore. Since 1951, the mine has operated underground using a block caving method. The mine produced 725 000 mt per year until 1978, when the rate of production was increased to 1 100 000 mt. The ore was produced entirely fm the first lift on 650 level until 1976. Then, a second lift on 950 level was put into operation to replace production facilities fm the first lift which is now exhausted. Annual fibre production is 72 500 mt with grades £ran 3 to 7. The total work force is 600 people. The host rock is a peridotite partially serpentinized. The asbestos fibre seams occur as stockwork deposit structurally controlled by talcose shear zone. The geological rock formations are heavily jointed and have a wide range of competence. Asbestos ore bodies have an heterogeneous nature which des difficult geological interpretation. THE GRIZZLY METHODS A full gravity method was used on the first level where the caved ore was drawn from finger raises onto grizzly bars spaced at 480 mn. Oversize blocks were reduced by secondary blasting. The ore fell by gravity in- to the ore pass below the grizzly chamber and was loaded into 5.7 mt haulage cars through a 1.2 m wide chute. Access to the undercut drift was fm the grizzly drift through finger raises. The undercut trough was drilled and blasted in a 1.2 m interval ring sequence into a slot situated at the end of each panel. The undercut stope was emptied through the finger raises. The undercut retreated from South to North at blast interval determined by the finger raises spacing. Fig. 1 represents the various steps involved with the grizzly method. Extraction drift dimensions were opened 1.8 m wide x 2.4 m high with anchor rock bolts and wire mesh where safety required them during excavation. Grizzly chambers were excavated at 2.4 x 2.4 x 4.6 m long on a 7.6 x 7.6 m grid spacing. Ore passes with dimensions of 1.5 x 1.5 m were developed from the haulage drift. On the extraction level, headings were drilled with jacklegs and cleaned by slusher into ore passes to the haulage chutes. The support used in the grizzly chambers was square concrete structure with 150 mn H beam reinforcement. The H beam was partially buried in the concrete and had one free face to allow for difference frequency of blast vibration between concrete and steel. The supported brow of the chamber had an opening 1.5 x 2.1 m. Ore passes were ring concreted 150 mn thick without any reinforcement. A 24 MPa compressive strength concrete was pumped and poured in pre-assembled forms. Based on the success of this method on the first level, the same layout was repeated on the second level. With the start of undercutting on the second lift, signs of deterioration were noticed in extraction drifts. At first, there was great concern as the operators were confident that standard repair techniques could cope with such a situation. An intensive program of support repair and a reduction of draw resulted. The following method of repairs were used: 1) Steel square sets of 150 mn H beam at 0.6 m intervals were installed. 2) This was reduced later to 0.3 m interval and eventually to a skin to skin steel structure. 3) Yieldable arches were introduced spaced at 0.9 m intervals, linked laterally with 150 m. H beam. 4) The yieldable arches spacing was then reduced to 0.46 m and eventually installed skin to skin. However, this support was not successful.

Jan 1, 1981

By John Wulff, David A. Stevenson

The solubility of iron and cobalt in liquid lead, the solubility of chromium in liquid tin, and nickel in liquid silver were determined up to 1300°C in an atmosphere of hydrogen. Liquid samples were taken at different temperatures and analyzed. The data obtained were plotted to show the relationship between log mole fraction of solute and the inverse of the absolute temperature. Resulting values for the differential heat of solution (AH) and the excesspartial molar entropy (S)are: for the iron-lead system = _24,200 cal per mole and AT = 5.0 e.u. for the a phase, and AH = 18,300 and S = -0.1 e.u. for the y phase; for the cobalt-lead system AH = 16,500 cal per mole and AS =0.7 e.u.; for the chromium-tin system AH = 15,600 cal per mole and AS = 8.5 e.u.; for the nickel-silver system AH =18,000 cal per mole and AS = 4.0 e.u. RECENT developments in coating, brazing, and heat transfer have focused attention on specific cases of solid-liquid interaction in metal systems, particularly those involving dilute liquid solutions. One fundamental quantity of interest in such systems is the equilibrium phase distribution between solid and liquid phases. In any effort to fully understand such interactions, one must be able to describe the equilibrium state precisely. Furthermore, in order to develop genera! relations for such systems, one must know the equilibrium state in a number of different cases. This investigation was devoted to a study of the equilibrium phase distribution in four binary systems: solid iron-liquid lead; solid cobalt-liquid lead; solid chromium-liquid tin; solid nickel-liquid silver. The iron-lead system was previously studied by Shepard and parkman&apos; and later by Fleischer and Elliott2 with differing results. Both investigations were carried out by sampling the saturated liquid, and analyzing it chemically. The cobalt-lead system was previously reported by Pelzel,3 who noticed no discontinuity near the transformation. A limited investigation of the chromium-tin system was made by Wlodek and wulff4 using a weight loss method. This work was done in conjunction with the development of a process for coating molybdenum with chromium from tin solutions. To more fully under- stand the kinetics of the process, a more accurate determination of a solubility was desirable. No significant data were found in the literature on the nickel-silver system. Data on the latter system were, however, relevant to the investigation of the corrosion kinetics of copper-nickel alloys in liquid silver as carried out by Harrison and wagner,5 EXPERIMENTAL APPARATUS AND PROCEDURE Of the techniques available for the study of such systems the most effective appears to be that of liquid sampling,2,6,7 which is the method used in the present investigation. A schematic diagram of the sampling furnace is given in Fig. 1. Large pieces of solute metal, in excess of saturation solubility, were added to 200 g of the solvent metal, and the entire charge placed in an alundum crucible. Analytical reagent or materials of chemically pure grade were used in all investigations. The crucible was contained in a zircon muffle tube positioned vertically in the uniform hot zone of a Globar resistance furnace. The tube was provided with a number of ports which permitted sampling at temperature and in controlled atmospheres or vacuum; the ports were also useful for evacuation and introduction of gases as well as for thermocouple measurements. A chromel-alumel thermocouple Sheated in a porcelain tube was used for temperature measurements. A purified hydrogen atmosphere was employed in all experiments reported in this paper. The hydrogen was purified by passing it first over hot copper gauze to remove oxygen and then through a molecular sieve immersed in

Jan 1, 1962

By Goldye Leeds, Marian Balicki

A SURVEY of literature reveals the scarcity of experimental evidence relating to work hardening and reannealing of silver.&apos;-&apos;" With the exception of the well-known X-ray investigation of silver and other metals by W. A. Wood? the effect of progressive cold working has not been studied. The determination of thermal stability of silver in the work-hardened state by means of isochronal or isothermal annealing has been confined apparently to very high reductions only. In the survey made, no study was encountered which endeavored to produce a complete picture of the changes in various properties due to cold working and subsequent reannealing. To fill these gaps and to assemble data that could be used for the determination of activation energies and of frequency coefficients of primary recrystallization, a systematic experimental approach, which was developed by one of the authors, has been applied to pure silver. Material and Processing The silver used was Handy and Harman fine silver, with a spectroscopic analysis at the testing stage of Cu, 0.0001 to 0.001 pct; Te, 0.0001; Pb, Si, Ca, Mg, and Mn, traces. The material was supplied in the form of a rod 0.406 in. diam and was converted into test samples according to the procedure condensed in Table I. It should be mentioned that air annealing was adopted to simulate industrial practice, though it was realized that annealing in a neutral gas or in a vacuum would be preferred. The usual precautions have been taken to eliminate any structural changes and property changes resulting from the storage of the samples prior to annealing or testing. Thus the wires were kept at the fully annealed stage, and the final wire drawing, which produced the desired degree of work hardening, was done just prior to the final annealing or testing. During the short waiting period, the samples were kept in a thermosflask filled with ice. Even with these precautions some strain-age-hardening or self-annealing could occur. To test such a possibility, wires of different reductions were prepared in the manner adopted and portions of them were immediately tested. The remaining portions were similiarly tested after different periods of storage, both at room and melting-ice temperature. Within experimental error, all samples obtained from a wire of a given percentage of reduction yielded identical values. This result qualified the material for further tests and interpretations, because it showed that either strain-age-hardening and self-annealing were absent, or that these effects fully balanced each other. The final annealing was carried out in an electric resistance furnace automatically controlled to within a 10°F. It was realized that the temperature fluctuations were greater than desired for this type of work. TO diminish the errors due to fluctuations of temperature, the hot junction of the thermocouple was placed as close to the samples as possible; the time of soaking was reduced to 15 min; and the number of samples annealed at different temperatures was increased. It will be seen from Table I that some tests were performed on the same material at rising temperature. These will be discussed elsewhere. Room temperature testing was limited to the determination of some of the mechanical properties that are known to be additive in a degree sufficient to be used for indirect study of the kinetics of the reannealing process, Tensile tests, carried out on a manually operated J. Camillon machine, accurate to within permitted the determination of the ultimate stress (U.S.1 and of the 2 in. elongation, (A,). The proof stress (d,e) has been determined from a series of bend tests carried out on a Tinius Olsen Stiffness Tester by using the offset method. This involved accurate determination for each sample of load-angular deflection curves, finding a

Jan 1, 1952