Search Documents

By G. R. St. Pierre, S. W. Gilby

The equilibrium vapors established over Fe-Cr-Ni alloys containing up to 50 pct Cr at 1600°C were determined by collecting the effusate from thoria Knud-sen cells. From these data, the activities of iron and nickel in the ternary alloys have been calculated. In a separate set of measurements, a mass spectrometer was used to determine the activities of the three components in a series of Fe-Cr-Ni alloys. In binary Ni-Cr melts, the activity coefficient of chromium referred to pure solid chromium as standard state is less than one at low chromium contents but is greater than one for melts containing more than 30 at. pct Cr. For Ni-Cr melts containing less than 10 at. pct Cr, In ?Cr = 0.15-0.92 N2. Ternary activity diagrams for Fe-Cr-Ni alloys are presented. In iron-rich alloys, the interactions between the three components are negligible; however, in nickel-rich alloys, the three principal interactions have significant positive values. THE activities of components in binary Fe-Ni alloys have been measured both in the solid solution1-3 and liquid solution4-6 temperature ranges. The determination for Fe-Ni melts have been made by three different methods: transpiration,4 Knudsen-cell effusion with analysis of an accumulated condensate,' and Knudsen-cell effusion with direct measurements of relative component intensities by mass spectrometric methods.6 The results obtained by the three different methods in three different laboratories are in excellent agreement and considerable confidence is placed in the activity coefficients for Fe-Ni melts. At 1600°C, the activity coefficients in dilute solution are ?°Ni = 0.66 and ?oFe = 0.40 for the pure liquid components as standard states. Measurements made on solid solution Fe-Cr alloys7-10 indicate that the component activities are slightly greater than ideal. The measured activities in iron-rich Fe-Cr liquid alloy11-16 indicate almost ideal behavior for this system. The recommended activity coefficient of chromium in dilute solution in liquid iron at 1600o C, ?oCr, is 1.18 when referred to pure solid chromium as standard state and 1.04 when referred to pure undercooled liquid chromium as standard state." The conversion factor of 1.14 is based on a melting point of 1857°C and an enthalpy of melting of 4047 cal per g at. for chromium.21,37 The activity coefficient of iron in dilute solution in liquid chromium has not been measured. Activity measurements on solid Ni-Cr alloys have been made by several investigators.17-20 During the review of this manuscript, Fruehan12 published the results of a study on liquid Ni-Cr alloys at 1600°C. He used galvanic cells22 with ZrO2(CaO) as the electrolyte and Cr/Cr2O3 for the reference electrode. His results indicate that ?oCr in nickel at 1600°C is about 1.01 when referred to pure solid chromium and about 0.89 when referred to pure undercooled liquid chromium as standard state. The activity coefficient of nickel in liquid chromium is unknown. The compositions of vapors freely evaporating from some molten Fe-Cr-Ni alloys have been measured by Lyubimov, Granovskaya, and Berenstein.23 Their results, combined with known vapor pressures, indicate strong positive deviation for chromium in iron-rich alloys and strong negative deviation for chromium in nickel-rich alloys. EXPERIMENTAL PROCEDURES This research was undertaken to determine the activities of components in ternary Fe-Cr-Ni melts containing up to 50 at. pct Cr. At the initiation of the research, we decided to use a Knudsen-cell method wherein a portion of the effusing vapor is condensed on a cold plate.' The composition of the equilibrium vapor for each alloy composition is determined in this method by holding the system under constant conditions for a period of time sufficient to collect enough condensate on the cold plate for chemical analysis. The activities of components in ternary alloys can be calculated from such vapor composition determinations by Eq. [1].24

Jan 1, 1970

By E. T. Turkdogan, W. L. Worrell

The rate of reaction of hydrogen sulfide with ferrous sulfide was studied by measuring the initial rates of sulfidation of iron strips in hydrogen sulfide-hydrogen-argon mixtures at 670°, 800°, and 900" C. The time-dependent surface sulfur activity is derived from the instantaneous rate of sulfidation with the assumption that diffusion in the sulfide layer is in a pseudo-steady state with the gas-sulfide chemical reaction. The rate of sulfur transfer from hydrogen sulfide to the surface of iron sulfide is proportional to the partial pressure of hydrogen sulfide and inversely proportional to the activity of sulfur at the surface of the sulfide layer. The derived rate equation is based on the assumption that most of the surface sites on the chemisorbed layer of iron sulfide are occupied by sulfur atoms and that the slow rate-controlling reaction is the dissociation of hydrogen sulfide on the chemisorbed layer. The experimental results are in reasonable accord with this reaction model. 1 HE slow approach to parabolic growth rate in the sulfidation of iron in hydrogen sulfide-hydrogen mixtures is a manifestation of slow approach to surface equilibrium between the gas and the surface of the sulfide layer. For example, at 800°C and Fig. 7 in Part I, the parabolic growth rate begins after approximately 1 day of sulfidation time. With decreasing temperature and decreasing partial pressure of hydrogen sulfide, the time necessary to reach gas-sulfide surface equilibrium is much longer. These observations are similar to those reported previously by Turkdogan et al.' on the oxidation of iron to wustite in hydrogen-water vapor mixtures. The slow approach to gas-sulfide equilibrium is well-demonstrated by the results in Fig. 1 where the square of the weight gain per unit area, ( g S per sq cmI2, is plotted against time for gas mixtures having PH g//>H = 1.0 with 0, 25, 50, and 67 pct Ar at 800°C. The value of 1.5 X lo-' (g S per sq cm)' corresponds to almost complete sulfidation of the iron strip (- 0.05 cm thick) to iron sulfide. The points fall on S-shaped curves. If the inflection parts of the curves are considered to be linear, thus indicating parabolic growth rate and the establishment of gas-sulfide equilibrium, their slopes would have to be the same for a fixed ratio in the gas mixture. Such is not the case, and the slopes for the "linear" parts of the S-shaped curves are lower than the value when gas-sulfide surface equilibrium is established. The subject matter of this paper is the kinetics of the surface reaction of hydrogen sulfide with iron sulfide during the early stages of sulfidation of an iron strip. EXPERIMENTAL RESULTS The apparatus and materials used were the same as those discussed in Part I. In the present experiments of relatively short duration, a purified iron strip, 5 by 2 by 0.05 cm, which was suspended in the uniform hot zone of a vertical zircon tube, reacted with a flowing gas mixture of hydrogen sulfide-hydrogen-argon. The sample was suspended from a gold chain attached to a calibrated silica spring. The amount of sulfur picked up by the iron, which formed a layer of iron sulfide, was determined by measuring the displacement of a reference point on the silica spring, using a cathetom-eter. In all cases, the degreased sample was first annealed in a stream of oxygen-free dry hydrogen for several hours to remove any impurities such as oxygen, nitrogen, or carbon which might have been present on the surface of the sample.' The rate measurements were carried out at 670°, 800°, and 900° C in hydrogen sulfide-hydrogen-argon mixtures with pH2 s/Ph2 ratios from 4 to 0.1. In a few experiments of short duration no sulfur deposition was observed in gas mixtures with (comments concerning sulfur deposition at high pH s/ph ratios were made in Part I.) Typical examples of the results obtained are shown in Fig. 2 for two temperatures and two gas compositions. With the present experimental technique, reproducible rate data could be obtained only after a uniform

Jan 1, 1969

By T. H. Alden

BaCKOFEN, Avery, and Turner have shown"2 that the large tensile elongation in superplastic metals is correlated with a high strain-rate sensitivity of the flow stress. At present, the reported superplastic materials are complex eutectic or eutectoid systems with a large solubility range in at least one of the terminal phases. This note describes the behavior of a solid-solution alloy (at 22°C)5,= Sn-1 wt pct Bi, which has been processed in order to produce a fine grain size.2,3,6 The chill-cast, 1/2-in.-diam ingot was homogenized for 1 week at 130°C, extruded at O°C to 0.083 in. diam, quenched within 15 sec, and stored at -196°C. Samples were warmed to room temperature 16 hr prior to mechanical testing or metallography. During tension testing at room temperature, it was found that the flow stress reached a steady-state value which depended on the imposed elongation rate and was independent of strain to an error of about ±5 pct. In Fig. 1 is plotted log a vs log e where a is the measured steady-state flow stress and i the imposed strain rate. These quantities were calculated using "instantaneous" area and length to an accuracy in the sample diameter of ±5 x 10-4 in. The log a-log 1 curve is sigmoidal. The strain-rate sensitivity, which may be given by d log old log 6,' has a maximum value of about 0.48 between i = 5 x 10-4 and 5 x 10-3 per min. The value is well above frequently measured values for metals at creep temperatures (0.1 to 0.3) and comparable to the rate sensitivity for Pb-Sn solder: which has been shown to be superplastic.2,3 Note, however, that below or above the strain rate of 10-3 per min the rate sensitivity of Sn-1 pct Bi decreases and at high rates is more nearly like that of conventional metals. The grain size of this material is relatively uniform, Fig. 2, and may be specified by an average linear intercept i.' Grain growth occurs at room temperature but after 16 hr, L = 5. Tensile elongation was measured on finer-grain-size specimens, which had been at room temperature 15 min prior to testing. After 15 min, the samples are fully recrystallized. Three strain rates, 5 x 10-3, 10-2, and 2.5 x 10-2 per min, were employed for which the measured elongations varied from 425 to 500 pct. These results would seem to justify the term superplastic, applied to this alloy, although the ductility is inferior to that of the Sn-Bi eutectic.3 The Sn-1 pct Bi alloy, which is a single-phase material with equiaxed, fine grains, is an excellent one on which to make an estimate of the Nabarro-Herring9 creep rate. According to the model of Avery and Backofen2 a substantial part of the deformation must be accomplished by N-H creep in the strain rate-temperature regime in which d log a/d log 1 = 0.5. The maximum N-H creep rate is given by9 L2kT where v is the atomic volume and D the self-diffusion coefficient. For this test v = 3.O x 10-23 cu cm, D = 1.4 e-23,300/RT = 2.5 x 10-l7 sq cm per sec,7 L = 5x 10+4 cm, T = 295°K, and a = 2000 lb per sq in. = 1.38 x 10' dyne per sq cm. The calculated creep rate is E= 4 x 10-11 per sec which may be compared with the measured creep rate at this stress, Fig. 1, of 6.7 x 10-5 per sec. The N-H creep rate is seen to be negligible. Earlier consideration2 of this question was in error because incorrect diffusion coefficients were used. The assistance of R. R. Russell in metallography is acknowledged gratefully.

Jan 1, 1967

By John J. McKetta. Jr., Louis B. Lesem, George H. Fancher

The proration of oil produced in the field frequently is based partially or entirely upon the gas-oil ratio of wells. The measurement of the gas-oil ratio is one of the more important field tests in regulatory and pro-ration work, and the test always should be conducted according to standardized methods and procedure. Obviously, the gas-oil ratio and the volume of gas produced by a well depend upon many factors but should be independent of the method of measurement and of the devices used to measure gas and oil. Consequently, the volume of gas accompanying a barrel of oil produced by a well may be measured by any reliable and accurate device or instrument. Frequently either a critical flow prover or an orifice well tester is used for this purpose, and for a particular well the same rate of flow of gas should be obtained regardless of whether a critical flow prover or an orifice well tester is employed in the test. In Texas, when using either instrument, either Capacity Table 1 or 5' is employed in making the necessary computations. If the tables are used, a discrepancy always is found whenever the two instruments are compared by extrapolation to the same conditions of flow. Clearly, Tables 1 and 5 must be at fault in some respects. The orifice well tester and the Bureau of Mines type of critical flow prover are essentially the same instrument; both devices utilize a square-edged orifice 1/8 in. in di-ameter as the primary element, and both freely discharge gas to the atmosphere. Tables for the orifice well tester' have been published in the ranges of 0 to 15 in, of water and 0 to 40 in. of mercury (Hg) differential in pressure. Coefficients for the critical flow prover have been published for differentials in pressure greater than 75 psia. An extrapolation of either differs from the other set of data as much as 18 per cent at some points. No immediately obvious reasons for the discrepancy was found, and data available from the literature were insufficient to effect reconciliation. Consequently, a series of experiments was performed to check the available data and to determine discharge coefficients for the two devices in an overlapping range of differential pressure. The correlating equation used in preparation of tables such as Tables 1 and 5' is the so-called hydraulic equation, Q = C1 vh .....(1) The tables cover orifice sizes from 1/8 through 1 1/4 in. A second set of tables, for use with greater differentials in pressure, apply only to the 3/4, 1, and 1 1/4-in. orifice plates over a pressure range of 0 to 40 in. of Hg. The correlating equation used in preparation of the tables is Q = C2 vH(29.32 + 0.3H)/G . (2) Each of these equations is valid only for the range to which it has been applied, and neither equation is valid for extrapolation. Theoretical equations for flow through an orifice are based upon assumptions of fractionless flow and an emergent jet the size of the orifice. A multiplier, C,, called the discharge coefficient, is inserted into the theoretical expression to compensate for both frictional losses and the contraction of the jet experienced in the plane of the orifice. Buckingham3 shows that C, should vary with the ratio of upstream to downstream pressure for flow of a compressible fluid at any average linear velocity through the orifice less than the velocity of sound. Work published by the National Advisory Committee for Aeronautics4 indicates that the variation continues into the so-called critical flow region until the vena contracta coincides with the plane of the orifice. The NACA work, however, does not indicate a leveling off of the coefficient. The work of the Bureau of Mines5 for the critical flow prover was based on differential pressures greater than 75 psi and indicates that the discharge coefficient, Cd, is constant in this region at a value of about 0.86.

Jan 1, 1958

By Howard Martens, Pol Duwez

IN two papers published in 1949, alloys of chromium with the refractory metals tungsten, molybdenum, tantalum, and columbium were investigated in view of their possible use as high temperature resisting materials. For the Cr-Ta system, a partial phase diagram was presented and the only intermediate phase was identified at Ta2Cr3. A phase of the same composition was also observed in the Cb-Cr system. The X-ray diffraction data presented in these papers, however, were insufficient for crystal structure determination. It is shown in the present study that the only intermediate phase in both the Ta-Cr and the Cb-Cr systems corresponds to the ideal stoichiometric ratio TaCr2, or CbCr2. Both structures are cubic, MgCu, type. At high temperature, however, TaCr2 has a hexagonal MgZn, type structure, which can be retained at room temperature by fast cooling. The alloys were prepared by melting in a helium arc furnace on a water-cooled plate. The design of the furnace was essentially the same as that described in ref. 3. Some alloys were also obtained by sintering compacts made of the mixed powders pressed at 80,000 psi. The sintering was carried on for 4 hr at 1375°C. The tantalum and columbium powders were supplied by Fansteel Metallurgical Corp., North Chicago, 111. The tantalum powder was the reagent grade, with a particle size smaller than 400 mesh and a total impurity content less than 0.1 pct. The columbium powder was smaller than 325 mesh and contained approximately 0.1 pct C and traces of Fe, Ti, and Zr. The electrolytic chromium powder from Charles Hardy, Inc., New York, was smaller than 300 mesh and contained about 0.1 pct Na, 0.05 pct Ca, and traces of Cu, Al, Mg, Si, and Co. Powder diffraction patterns were obtained with a 14.32 cm camera, using copper Ka radiation filtered through nickel foil. The powder pattern of the TaCr2 alloy obtained by sintering at 1375'C was different from that obtained on the same alloy rapidly cooled from the melt. Contrary to this result, the powder pattern of CbCr2 was the same, whether the alloy was made by sintering at 1375°C or by melting, and was similar to that of the TaCr, sintered. It was also found that the structure of the TaCr2 specimen obtained by melting was retained after heating for 4 hr at 1590°C, but transformed into the structure found in the sintered specimen after heating for 4 hr at 1375°C. Hence, the structural change of TaCr2, appears to be a reversible polymorphic transformation. CbCr2 and ToCr2 Structure, Low Temperature Form By using large scale Hull-Davey charts, the powder pattern of CbCr, and of the low temperature form of TaCr2 were readily interpreted on the basis of a face-centered cubic lattice with a parameter of approximately 6.95 kX. The indices of the reflections together with the values of sin' 0 are given in Tables I and 11. From this list of observed reflections, it appears that the (200), (600), (024), (046), and (028) reflections are missing. The lack of (h00) reflections for h 4n indicates a four-fold screw axis. The missing (Okl) spectra for k + 1 An indicate the existence of a diamond glide d. The combination of these symmetry elements can be found in the O— Fd3m space group, which is therefore the most probable one. After having determined the approximate density of TaCr, by the immersion method, the number of molecules per unit cell was calculated and found to be nearly eight. This information, added to the fact that the most probable space group is O leads to the consideration of a structure of the MgCu2 type, in which the atoms have the following positions: 8 magnesium in a and 16 copper in d. On the basis of this structure, intensities were computed by means of the usual formula: 1 cos'20 I a sin2 cos where F is the structure factor; 8, the Bragg angle: and p, the multiplicity factor. As shown in Tables I

Jan 1, 1953

By R. J. Wasilewski

Electrical resistivity variation with temperature was measured on a series of alloys containting up to 33 at. pct of oxygen over the range 77° to1500°K. The resistivity behavior is highly anomalous and itzconsistent with simple metallic conduction. Both composition and temperature-depended resistivity singularities were observed. A few experiments carried out on Ti-N and Zr-O alloys indicate the presence of similar anomalies. These observations, together with the published data on effects of substi-tutional alloying on the resistiuity of titanium, suggest that the anomalies are inhevent in the electron structure of this group oj metals. The existence of two-band conduction, and a significant shift of bands relative to each other with temperature and/or the electron concentration are suggested. CONSIDERABLE advances have been made in recent years in the alloy theory of simple metals. Very little, however, is known about the bonding in transition metals and their alloys.&apos; Titanium, with its relatively few electrons, may be expected to show simpler alloying behavior than the more complex transition elements. Its alloys with the interstitial elements appear particularly attractive in an investigation of bonding characteristics because of a) the simple nature of the solute elements, b) the remarkable similarity between the equiatomic structures Tic, TiN, and TiO, and c) the extensive solid solubility ranges of oxygen and nitrogen in a titanium reported.2,3 The Ti-O system was chosen for the most extensive investigation because of the relative ease of preparation of suitable specimens. Since the main object of the work was to obtain data on the bonding and its changes on alloying, electron-sensitive properties were primarily investigated. The present work describes the investigation on the electrical resistivity-temperature-oxygen content relationships. A few experiments were also carried out at selected compositions in the Ti-N and Zr-O systems. EXPERIMENTAL Materials and Method. Polycrystalline specimens were prepared in the form of hairpin strips some 50 by 5 by 0.15 to 0.50 mm by direct metal-gas reaction. This was carried out by controlled oxidation followed by a homogenizing anneal at a higher temperature. All the test specimens were fully homogenized as judged from the uniform microstructure and microhardness. To avoid preferred orientation, each strip specimen was annealed in the ß range prior to the oxidation, this procedure assuring random orientation in the strip;4 hence any texture resulting from the oxidation reaction itself affected all the specimens to a similar extent. Titanium used was of high purity (66 DPN, 10 Kg load; major impurities 0,-43G ppm, N,-70 ppm, C-25 ppm, Fe-14G ppm). The solute content of the alloys was determined by weighing, after the reaction with a known amount of oxygen. The specimens in which the discrepancy between the volumetric and gravimetric measurements exceeded 2 pct (or 0.2 mg for the low oxygen alloys) were rejected. The mean between the two measurements was then taken as the oxygen content of the alloy. Check analyses showed no measurable nitrogen contamination. All oxygen contents are given in atomic percent. Zr-O alloys were prepared in identical manner from hafnium-free crystal bar metal, cold-rolled to strip 0.25 mm thick. Ti-N alloys required very long reaction times at the maximum temperature available (1250°C). In order, therefore, to detect possible oxygen contamination, duplicate specimens were reacted in every experimental run, and one of these was analyzed both for oxygen (vacuum fusion) and for nitrogen (Kjeldahl). Only the specimens in which the check analysis showed < 1000 ppm O were then used for resistivity investigation. Since only relatively high nitrogen alloys (7.1 at. pct; i.e., 2 wt pct N,) were investigated, this oxygen contamination was considered permissible. Dc resistance was measured by the four-probe method as previously described.= The temperature was determined with a calibrated thermocouple placed in the center of the specimen hairpin. The errors in the specimen resistance values thus obtained were estimated at 1 pct due almost exclusively to the finite thickness of the potential wires and the consequent uncertainty as regards the true resistance length of the specimen. For the calculation of the specific resistance, however, no dimensional measurements could be carried out on most of the

Jan 1, 1962

By P. Martinez, A. F. Hoyte, F. E. Senftle

The possibility of applying a neutron activation technique for silver exploration is considered. A mobile positive-ion accelerator type neutron source is used to irradiate a small area of rock or soil in situ. By using a short period of irradiation and gamma ray spectral analysis, a technique is shown for silver exploration. Two different mobile units are described. Laboratory and preliminary field tests both indicate that a sensitivity of less than 1 oz of silver per ton of ore can be achieved. The increasing consumption of silver for industrial uses and also for coinage has caused a serious shortage of silver in this country. The silver shortage has been reviewed and analyzed by kiilsgaard1 who concludes that, "The best hope for meeting future demands for silver is through accelerated exploration for precious ores." As almost all the exposed "bonanza" type silver deposits evidently have been found, it is urgent that some sensitive geophysical technique be found to detect large, extended, but generally low-grade, secondary ores, as well as hidden vein deposits. Silver is easily made radioactive by exposure to slow neutrons; hence a neutron activation method appears promising for locating silver deposits. The principles of mineral beneficiation using neutron activation techniques were discussed some years ago.2-4 Using the same approach, a preliminary description5 has been published of neutron activation as a mineral exploration tool. An exploration technique is described in which silver is made radioactive in situ and detected with a gamma radiation counter. The technique is similar to the well-known method used for uranium exploration. THEORETICAL CONSIDERATIONS Elemental silver consists of two isotopes, Ag107 and Ag109, having naturally occurring isotopic abundances of 51.4% and 48.6%, respectively. For short periods of irradiation of silver by thermal neutrons, the long-lived 250 day, half-life isotope, Ag110m, is not produced in significant quantities. However, significant quantities of 2.3 min half-life Ag108 and 24.5 sec half-life Agl10 are formed by the following reactions. Ag108 and Agl10 emit a 0.44 Mev (million electron volts) and a 0.66 Mev gamma ray, respectively. Ag107 + n + Ag108 (2.3 min) Ag109 + n + Ag110 (24.5 sec). Because of the large capture cross section (110 barns) of Ag109, and short half-life of Ag110 (24.5 sec), the 0.66-Mev gamma ray is the most prominent emission from silver for neutron activation periods of about a minute&apos;s duration.* The 0.44-Mev gamma ray from Ag108 will also be present, but will be one or two orders of magnitude lower in intensity. The decay scheme of Ag110 is shown in Fig. 1. If the neutron irradiation time is limited to about 100 sec, the Ag110 activity will essentially reach saturation and can be used to detect the presence of silver. In a neutron flux of 10 8 neutrons/cm2/set, the induced 0.66-Mev activity in 1 g of silver will be about 2 x 107 disintegrations per sec. This is about 1000 times the measurable gamma activity of 1 g of uranium in equilibrium with all its decay products; hence there is ample activity for detection. Under the same conditions of activation, most of the other elements do not reach this relatively high disintegration rate. Although this is in favor of the proposed technique, other problems must be considered. For mobile operation, it is desirable to obtain the largest neutron flux to weight ratio. Hence we have used a small 150-kev accelerator-type neutron source rather than an isotopic source such as an americium-beryllium neutron source. By use of remote control system, an accelerator-type neutron source can be safely used without the massive shield required for an isotopic source. Moreover, an accelerator-type source is more versatile in that it allows one to use a flux of either 14-Mev or 3-Mev neutrons, depending on whether a tritium or a deuterium target is used. With a 14-Mev generator, one can obtain a flux of 10 9 neutrons/cm 2/sec, and with a 3-Mev generator, the flux is generally two orders of magnitude less. Although silver will become activated with either generator using proper moderation, detection may be

Jan 1, 1968

By P. J. Spencer, J. N. Pratt

The vapor pressure of manganese over liquid Mn-Sn alloys has been determined by a high-temperature torsion-effusion technique. Alloys containing from 8 to 100 at. pct Mn were investigated in the temperature range jrom 1280" to 1580" and the measured pressure values were used to calculate the partial and integral thermodynamic properties of the liquid alloys. The activities show small negative departures from ideality while the integral heats and excess entropies of mixing are asymmetric inform, changing from positive to negative with increasing manganese content. The possible contribution of various factors to the observed thermodynamic properties is discussed. COMPARATIVELY few thermodynamic data are available for manganese alloy systems.&apos; Therefore, as part of a continuing program of studies of the thermodynamic properties of transition metal alloys, measurements have been made on various binary alloys involving this element. In recent publications,2~3 investigations of liquid Mn-Cu alloys and of the Mn-Au system in both solid and liquid states have been reported. For the first-mentioned system the work suggested that magnetic interactions may be responsible for the observed form of the thermodynamic properties, while in the second the influence of the electrochemical factor appears to be dominant. The present paper describes a similar study of liquid Mn-Sn alloys. Again the thermodynamic properties have been obtained from vapor pressure measurements made by use of a high-temperature torsion-effusion technique.4 A detailed description of the apparatus and of the experimental procedures used in alloy preparation and pressure measurement may be found elsewhere.2&apos;4 EXPERIMENTAL RESULTS Sixteen alloys, ranging in composition from 8 to 100 at. pct Mn, were prepared from spectroscopically standardized manganese of 99.99 pct purity and tin of 99.999 pct purity, both supplied by Johnson-Matthey and Co., Ltd. One-gram samples of the alloys were obtained by carefully weighing appropriate amounts of the pure components into an effusion cell; this was then suspended in the apparatus and the metals melted together in situ by heating under vacuum to approximately 1550°K. After allowing sufficient time for a homogeneous liquid alloy to be formed, vapor pressure measurements were commenced. These were determined as rapidly as possible at a series of steady temperatures within the range of interest. The duration of experimental runs on individual samples was kept sufficiently short to ensure insignificant varia- tion of alloy composition during investigation. After completing pressure measurements, the alloys were rapidly cooled and their compositions checked by weighing or chemical analysis. All experiments were conducted using effusion cells machined entirely from boron nitride. Measurements were made using a variety of cells with orifice areas ranging from 0.0032 to 0.0075 sq cm and lengths of the order of 0.04 cm; the usual effusion correction factors for orifice geometry and molecular distribution were calculated using Freeman and Searcy&apos;s equation5 and had values between 0.6 and 0.75 for the orifices employed here. The vapor pressures of manganese over the alloys were measured at approximately 20°K intervals in the temperature range 1280" to 1580°K. In view of the close approximation of the measured pressures to Clausius-Clapeyron behavior in the experimental temperature range, the data for each alloy have been expressed by equations of the form: logp(atm) =-A/T + B A least-squares computer treatment was applied to the vapor pressure values in order to obtain the coefficients A and B with their associated error. The resulting equations are listed in Table I, together with the equation for pure solid manganese obtained from a previous study.4 To minimize the effect of possible apparatus calibration errors, the activities and partial free energies of manganese in the alloys were calculated by initial reference to the latter equation, obtained from identical torsion-effusion measurements. The immediately resulting thermodynamic quantities, based on a solid manganese reference state, were then converted to refer to the more appropriate supercooled pure liquid manganese standard; tabulated values of the free energies of solid and liquid manganese from Hultgren et al.&apos; were used for this purpose. Partial entropies of solution of manganese were calculated from the temperature coefficients of the free energies and partial heats from the Gibbs-Helmholtz relationship.

Jan 1, 1969

By P. E. Busby, C. Wells

FURTHER study of data used in determinations of 1—rates of diffusion of boron in austenite and 2—solubilities of boron in the a and phases of iron and steel&apos; has provided an equation for the diffusion of boron in a iron. In brief, the previously published data were accumulated from the results of deboron-izing (and decarburizing) experiments carried out in the range of 700° to 1300°C. Diffusion coefficients (D?) for boron in austenite were calculated using the Grube solution of Fick&apos;s law. However, only solubility values were estimated from the discontinuous concentration-penetration curves, Fig. 1, which are characteristic of diffusion in two phases. Dr. Carl Wagner&apos; has recently provided a solution for calculating D values from penetration curves of this type as follows: Cl1.1 —C8/C8- C11.1 = vp ? e ? erf (?) and D = ?/4?2 t where C11,12, C8, C11, and E have the values shown in Fig. 1. D is the diffusion coefficient, sq cm per sec; t is time of deboronizing anneal, see; and ? is a di-mensionless parameter. For a given diffusion experiment, the value of ? can be readily obtained by graphical solution from a plot of y vs the right-hand part of Eq. 1. D may then be evaluated from Eq. 2. The avplication of this solution to previously re-ported results, of which excerpts are given in Table I, permits the calculation of diffusion coefficients for boron in a iron. On the basis of these meager data, it is tentatively concluded that the diffusion of boron in a may be represented by the equation Da = 1011 e-92,900/RT where R is the gas constant, cal X 0C-1 X mol-1; and T is the absolute temperature, OK. Although the frequency factor, 106 sq cm per sec, is admittedly several orders of magnitude higher than expected, the value of Q, 62,000 cal per mol, appears reasonable and is, in fact, very similar to that for the self-diffusion of iron. It is pertinent to mention at this point that the value of Q obtained for the diffusion of boron in austenite by means of the Wagner solution is 19,000 cal per mol and is in excellent agreement with the value previously reported1 in the equation DT = 2xl0-3 e-21,000/RT [4] which was determined by the application of the Grube solution to other data. The fact that determined constants A and Q in the equation D? = A e-Q/RT were practically the same, independent of whether the Wagner or Grube solutions were used in determinations of D values, strengthened the authors&apos; belief that the computed values of D (Table I) using the Wagner solution are reliable. The relative values in Eqs. 3 and 4 for the diffusion of boron in the a and ? phases, respectively, suggest that boron forms a substitutional solid solution in a iron and an interstitial solid solution in ? iron. The same tentative conclusion has been reached by McBride et al.3 on the basis of relative solubilities, atom diameter, and the size of the interstitial hole in a and ? iron. In connection with the data for test 14 listed in Table I, it is of interest to calculate the solubility of boron in a iron using the D value given by Eq. 3. As might be anticipated from the small movement of the interface in test 14, proper substitutions in Eqs. 2 and 1 give a low value, approximately 0.0004 pct B, at 850°C. Apparently at 835°C (test 13) it is possible to obtain 0.0018 pct B, and at 850°C only 0.0004 pct B into solution in the a phase before a second phase appears. These observations are consistent with the Fe-B constitution diagram proposed by McBride, Spretnak, and Speiser.3 References P. E. Busby, M. E. Warga, and C. Wells: Diffusion and Solubility of Boron in Iron and Steel. Trans. AIME (1953) 197, p. 1463; Journal of Metals (November 1953). &apos;W. Jost: Diffusion in Solids, Liquids, Gases. (1952) pp. 69-71. New York. Academic Press Inc. "C. C. McBride, J. W. Spretnak, and R. Speiser: A Study of the Fe-Fe2B System. Trans. ASM (1954) 46, p. 499.

Jan 1, 1955

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.&apos; Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.&apos; Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951

By J. T. Norton, H. Blumenthal, S. J. Sindeband

The interstitial phases formed by the transition elements with carbon, nitrogen and boron constitute a unique class of substances which are of considerable technical interest because of their well developed metallic properties and their high hardness and melting points. They are also of interest from the point of view of structure. It was pointed out by Hagg1 some years ago that the principal factor determining these structures was the relative sizes of metal and metalloid atoms. He predicted that if the ratio of the radii of metalloid to metal atoms was less than 0.59, the metal atoms would be arranged in a close-packed fashion of relatively simple type. This prediction has been amply confirmed. It appears, however, that this specification applies most generally to those structures in which the metalloid atoms occupy isolated positions in the lattice and there is no tendency for strong binding between the metalloid atoms themselves. The series of borides of the type MeB2 formed from the transition elements of the fourth (Ti, Zr) and fifth (V, Cb, Ta) groups of the periodic table provide an opportunity to investigate this situation further. If one takes as a basis the radius of 0.87 A for the boron radius and the Goldschmidt values for the metal atoms in 12 coordination, then the radius ratio varies from 0.54 for zirconium to 0.64 for vanadium, which latter is considerably greater than Hagg&apos;s limit of 0.59. It was of interest, therefore, to see if these five elements would form borides of the MeB2 type and have simple isomorphous structures. When this investigation was initiated, relatively little information had been published on the structure of this group of borides. McKenna2 reported the preparation of ZrB2 by a carbon reduction process. Its structure was hexagonal and the approximate lattice constants were given as a = 3.15 A, c = 3.53 A. Ehrlich3 reported the structure of TiB2 as being of the C 32 type with a = 3.02, c = 3.21 and c/a = 1.06 A. Recently, Kiessling4 published the results on ZrB2, showing it to be one in which the metal atoms are arranged in a simple hexagonal lattice with the boron atoms in flat sheets, midway between the layers of metal atoms. The structure is C 32 type with a = 3.169, c = 3.530 and an axial ratio =1.11 A. He also states that CbB2 and TaB2 are isomorphous with ZrB2. Preparation of Borides The borides of titanium, zirconium, columbium and tantalum were made by the electrolysis of fused salt baths after the method described by Andrieux.5 The bath, totalling about 6500 g in each case had the following general composition: Metal Oxide + B2O3 + CaO + CaF2. The actual proportions of the ingredients were determined for each individual case. Although Andrieux reports the preparation of vanadium boride by the same electrolytic method, several attempts proved unsuccessful. However, it was possible to prepare VB2 by the carbon reduction method used by McKenna to produce ZrB2. The mixture consisted of V2O5 + 6B2O3 + 11C and the reduction was carried out in an induction heated graphite crucible. This method proved satisfactory for ZrB2 and TiB2 and undoubtedly the others could be made in the same way. The borides, which were all in the form of fine gray metallic crystals from the electrolytic bath or gray powders from the reduction process, were carefully separated from other constituents and analyzed chemically for metal and boron content. The densities of the boride powders were measured using a standard 10 cc pyenometer at 18°C and ethyl benzene proved to be the most satisfactory liquid for this purpose. X Ray Technique The boride crystals, as prepared, were too small for single crystal examination so that powder techniques were employed. Patterns of the finely ground borides were prepared, using the Norelco recording X ray spectrometer. The lines on these patterns were indexed with the aid of Hull-Davy charts and the approximate dimensions

Jan 1, 1950

By M. B. Kasen

eralized strain equation appear quite different they are really identical. This identity can be shown in a simple mathematical rearrangement. Referring to Eq. [I], the substitution of ln(1 +?E) for ? (where ?E is the engineering strain) yields: a =s8- (s8?so)e?1/?c) ln(1 +s8??E) [4] or s =s8?(s8?so)(l +?E)-1 [5] Replacing (1 + cE) with its equivalent, (l/lo): s=s8?(s8?so)l/€c [6] Adding and subtracting the quantity (s8 - so) yields: s=s8?(s8?so)+ (s8-so) l-(^)l/£c [7] = s0+(s8?so)ri-(^0)1/^l [8] Letting n = 1/?c it follows that: This equation will be seen to be identical to the generalized strain expression in Eq. [3], the coefficients a and b being equal to so and (s8?so)/?c or n(s8?so), respectively. Confirmation of the relationship noted above was provided by fitting experimental stress-strain data5 for 304 stainless steel (total strain from 0.072 to 1.15) at room temperature at a true total strain rate of 4 x 10-3 sec-1 to Eqs. [I] and [3]. In this study nonlinear regression analyses were used to evaluate the equation constants. The results of this evaluation are presented in Table I. When these constants are used in Eqs. [I] and [3] the curves obtained are coincident. It will also be noted that the value of n is equal to YE,, the value of a is equal to so, and the value of b is equal to (s8 - so)/Ec. These equalities are illustrated in Table I where the Voce constants in parentheses were calculated from a, b, and n values. Excellent agreement is seen to exist. It is concluded, therefore, that the Voce equation is, indeed, identical to the linear expression involving generalized strain. In applying the generalized strain concept to stress-strain data, it has been noted3 that data within what was termed the transition region (first few points in the plastic flow region) must be excluded from the analysis in order to obtain the linearity in Eq. [3]. A similar exclusion applies in the use of the Voce equation since an expression which would describe the strain-hardening region would usually be found to be not too effective in the elastic-plastic fillet2 which connects the elastic line to the strain-hardening region. These considerations further substantiate that Eqs. [I] and [3] do indeed describe identical behavior. Note added in proof. Since this manuscript was submitted for publication, correspondence with Professor S. R. Davies, University of Edinburgh, (of Ref. 3) indicated that his associates have also confirmed the identity between the Voce equation and the generalized strain concept. It is sometimes desirable to obtain a small grain size in super-purity metals. Unfortunately, the absence of impurities, the low recrystallization temperatures, and the low activation energies for boundary motion result in rapid growth of relatively few grains when conventional recrystallization practices are used. For example, Arajs et al.1 were unable to obtain a mean grain diameter less than about 0.4 mm in iron containing 38 at. ppm of impurity. The <1 at. ppm purity range in many modern superpurity metals results in yet larger limiting grain sizes. It is the purpose of this communication to describe a technique by which mean grain diameters as small as 30 µ have been produced in aluminum having an impurity content < 0.5 at. ppm. The technique should be applicable to superpurity metals other than aluminum and has potential applications to grain refinement of commercial alloys. The necessary and sufficient requirements for production of a small grain size are as follows: a) a large number of potential nucleating sites must be created randomly within the cold worked material, b) sufficient thermal energy must be provided at a rate that will simultaneously activate a large fraction of the potential nuclei, and c) the grain growth must be stopped shortly after grain impingement.&apos; A high density of potential grain nuclei may be cre-

Jan 1, 1970

AN intermetallic compound, Ni3A1, has an ordered fcc structure of type Ll2, and shows peculiar dependence of the yield stress upon temperature; i.e., the yield stress increases by a factor of six upon raising the temperature from 77" to 900K1, 2 This compound is technologically important, since many nickel-base superalloys owe their high-temperature strength to the peculiar yield stress behavior of Ni3Al. The only study of the elastic behavior of this compound was made by Davies and Stoloff,1 who determined Young&apos;s modulus of poly crystalline Ni3A1 between 300" and 730°K. The determination of single-crystal elastic constants of Ni3A1 is therefore of interest in connection with dislocation dynamics and is reported in this paper. A single-crystal specimen, 1 by 1 by 3 cm, was cut from an ingot generously supplied by Dr. B. H. Kear of Pratt & Whitney Aircraft. Following initial machining with a Servomet and a surface grinder, the specimen was etched and annealed at 1100°C for 5 hr in vacuum followed by furnace cooling. Two parallel faces were oriented normal to within ±l deg of a [I101 crystallographic axis by the back-reflection Laue technique. The parallel faces were hand-lapped, etched, and polished by the usual metallographic procedures. Final thickness along the [I101 axis was (0.9325 * 0.0005) cm. Chemical analysis gave an average composition of 87.35 pct Ni. Total impurity content is esimated to be no more than 0.1 pct. The elastic constants were calculated from measurements of ultrasonic waves which were propagated along the [110] axis. A longitudinal wave and two shear waves whose displacements are aligned along the [ 110], [li~], and [001] directions, respectively, are necessary in order to completely specify the three elastic constants. Two 3/6-in. quartz transducers were bonded to the parallel faces of the sample with ~ac-seal.3 Although this bond was sensitive to thermal shock, it performed satisfactorily over the entire temperature range for both longitudinal and shear wave propagation. A frequency of 5 mHz was employed in the method of Williams and Lamb4 in order to measure the absolute value of the ultrasonic velocity. The pulse-overlap technique of Mcskimin5 was also used at this frequency in order to determine the shift in the ultrasonic velocity

Jan 1, 1970

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.&apos; The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.&apos;

Jan 1, 1964

By Augustus Locke

Jan 1, 1923

By Augustus Locke

Jan 1, 1923

By W. L. Worrell

R. C. Gifkins (CSIRO)—In this paper evidence is put forward to support the idea of grain boundary shearing in aluminum at 4.2°K and the phenomenon is explained in terms of a low-temperature "equicohesive temperature". It is stated that these findings show that grain boundary shear cannot be ruled out in any situation by temperature arguments alone. We believe, from our own recent study of "apparent grain boundary sliding&apos;&apos; at temperatures below 0.45 Tm, that it can be ruled out on temperature arguments alone.45 Our experiments were made principally with magnesium and a Ms-A1 alloy ("Magnox A12"). Careful examination of offsets of marker lines or steps at grain boundaries produced by deformation at room temperature (-0.3 Tm) showed many of these to result from curvature over narrow zones along the grain boundaries. A significant residuum did, however, appear as a sharp offset or step. It was found that the mean value of this step rose to a small value during the first 0.5 to 1 pct strain and then remained at this level with further strain. Moreover, exactly the same values were obtained (at the same stress) at 75°C instead of 21°C. That is, in this range of temperature the "apparent sliding" was not temperature-sensitive. At 125°C and above there was sliding which increased with strain and which was temperature-dependent. When this temperature-dependent sliding was used to calculate the sliding to be expected at room temperature, this underestimated the "apparent sliding" by a factor of 104. The conclusion drawn is that the "apparent sliding" consists of shear localized in a zone of a width measured perhaps in microns, whereas it seems that true sliding occurs on the boundary surface.46 A model for such localized shear has been developed in general terms, following a similar model of Urie and Wain.47 Other strong evidence for low-temper- ature sliding has been based on the offsets of marker lines consisting of a substructure seen using the electron microscope to resolve these.48 We have repeated this work and found that the effects can be accounted for in terms of cracks in an oxide film which is produced when the substructure is etched up; these cracks form over zones of shear rather than at actual interfaces. However, in aluminum at room temperature (-0.3 Tm) there is no "apparent sliding" which is optically detectable. We suggest that, when the temperature is much lower (and possibly the rate of strain higher, too), as in the experiments of Chin et al., then aluminum behaves like magnesium at room temperature, and a narrow zone of shear develops to accommodate differences in strain across the grain boundary. Such a zone could well give rise to triple-point cracks. It is hoped to investigate these suggestions further. B. Y. Chin, W. F. Hosford, Jr., and W. A. Backofen (authors&apos; reply)—It is interesting to have Dr. Gif-kin&apos;s comments, although it is somewhat difficult to reply in detail without the reference containing the work that he describes. Apparently though, he does find a low-temperature temperature-independent sliding that would seem to be related to the observations reported here. Perhaps some of the difficulty has semantic origins, growing out of the distinction between (&apos;true sliding" and "apparent sliding".

Jan 1, 1965

By B. H. Kear, H. G. F. Wilsdorf

After a few percent strain, dislocations in disordered Cu3Au are arranged in groups in ulell-defined slip planes, which contrasts with the more or less random distribution of dislocations in the corresponding ordered alloy. Unusually long and straigkt dislocation segments observed in the ordered alloy are interpreted in terms of cross slip of screw dislocations from their slip planes into cube planes. It is proposed that cross slip, and also dislocation reactions of the Lomer type, play an important role in work hardening of the ordered alloy. ACCORDING to to dislocations in the disordered lattice are only partial dislocations in the corresponding super lattice, so that in the super-lattice dislocations must occur as pairs, with each pair connected by a ribbon of antiphase boundary. Recently, striking confirmation of the theory was obtained by Marcinkowski, Brown, and Fisher3j4 in a study of dislocation configurations in thin foils of the Cu3Au alloy by transmission electron microscopy. In the present investigation, the observations made by these workers have largely been confirmed. Moreover, it has been found that dislocations in the plastically deformed ordered alloys are often unusually long and straight. This paper is mainly concerned with these new observations. A tentative explanation is offered in terms of cross slip of dislocations in the ordered alloys. PREPARATION OF SPECIMENS An alloy close to the stoichiometric composition Cu3Au was prepared by melting together high-purity copper and gold (99.995 pct) under vacuum in a graphite mold. The resulting ingot was rolled down and cut into strips 1 1/2 by 1/8 by 0.005 in. in thickness. All strips were annealed at 900°C for 3 hr and cooled to 500&apos;~. A few of the strips were quenched from ~OO&apos;C, while the remainder were slowly cooled in the temperature range 400" to 150°C at intervals of a few degrees every 24 hr to produce a high degree of order. After this annealing treatment the average grain size of the material was about 0.1 mm. Material in different states of order was obtained by reannealing fully ordered material at temperatures below the critical temperature: followed by quenching. The equilibrium degree of order attained at a particular reannealing temperature was obtained from the paper by Keating and warren.&apos; A simple hand-operated tensile jig was used to give the strips the required amounts of plastic strain. Following straining, a number of specimens were cut from each strip by means of an electrolytic cutting device.= Finally, each specimen was thinned electrolytically using the polishing procedure described by Bakish and Robertson,7 and these thin sections were examined in the Philips EM-100B electron microscope operating at 100 kv. EXPERIMENTAL OBSERVATIONS Antiphase boundaries. The average domain size in the ordered alloys was found by direct observation to be about 0.25 p. Also, it was observed that the grown-in configuration of antiphase boundaries was changed little by plastic deformation, at least up to 6 pct strain. Fig. 1 shows an electron micrograph of a thin foil of partially ordered alloy (S - 0.8) after 3 pct strain. The micrograph shows a few dislocation pairs and a somewhat crystallo-graphic network of antiphase boundaries. The normal to this foil was found by diffraction analysis to be approximately 11121, with principal directions in

Jan 1, 1962

By L. P. Bayvel

The method of spectral transparency was investigated. A device for measuring particle sizes based on this method was developed, tested and applied. The device affords measurements of particle size distribution in the range from 0.1 to 4 µm. It proved possible to measure sizes not only of spherical particles but also of non- spherical ones. The spectral range in which it is necessary to determine transparency for particle size measurements was found.

Jan 1, 1980