Search Documents

By Ralph W. Smith

Development of the lime industry in Ste. Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there arc today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. Geology The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft, of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCo3; 0.35 SiO2; 0.3 R2O3; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 1/2°. Thus the outcrops of the various sedimentaries run approximately north and south. A line running west from Ste. Genevievc crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile wide. The early quarry and lime developments at Ste. Genevieve mere in this easily obtained surface rock of the Spergen outcrop.

Jan 1, 1938

By G. A. Reinhardt, H. J. Cutler

ThE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4-in. (14.5 cm.) square bloom to a 3/4-in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900" to 950' C. and cooling slowly in mica. The test bars were tempered by heating to 825' to 875" C., quenching in water, and drawing to 515" to 535" C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. UlTimate Strength.. Elongation, Lb. pER Sq. In. PEE Cent.. in 4 In. Not LeEs Than Annealed specimens.............. 78,230 to 92,450. 18 Tempered...................... 120,000 to 149,350 9 After experience on this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850" to 900" C. and cooling in still air; the annealing, in heating to 850" to 900" C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were: yield point, pounds per square inch minimum, 44,800; ultimate strength, pounds per square inch, 89,600 to 112,000; elongation, per cent. in 2 in. not less than 17. Difficulty was encountered as soon as work on this material was started. Many precautions and refinements were instituted but it was found very difficult to secure the required elongation.

Jan 1, 1920

By D. K. Crampton

The object of this work was to obtain and correlate information on effect of internal stress in variously drawn tubes on several properties. Also, a simple approximate method of comparing types of stress distribution in such variously drawn tubes was sought. There is also included some work on comparison of single and polycrystalline materials and effect of different types of operation and preferred orientation. Preparation of Material A series of tubes was drawn to study the effect of the type and degree of final reduction on various physical properties and the approximate distribution of stress intensity across the tube wall. The material used all came from a single heat of 70-30 brass melted in a regular production Ajax-Wyatt induction furnace. The analysis of the metal as cast was: copper, 70.36 per cent; lead, 0.04; iron, 0.02; zinc, balance. The material was cast in "shells" with 4 in. outside diameter and in. wall thickness. It was drawn part way down according to the usual standard mill schedule and then by suitable individual schedules to finish by a variety of types and degrees of drawing to the same final cases in every instance; namely, 0.750 in. outside diameter by 0.080 in. wall thickness. The exact final draws, together with the percentage area reductions, diameter reductions and gage reductions are given in Table 1. In fabricating these tubes, rather unusual precautions were observed to insure the elimination of ail variables not under immediate study. All intermediate anneals were carried out at about 1200" F. down to the so-called "cut-in size"; namely, 17/16 by 3/16 in. From this point on, all anneals were made at from 1050' to 1100" F. The greatest care was used all through to have the tubes as free from minor surface defects as possible. When such defects were visible on intermediate sizes they were carefully filed out. On the final draw to 3/4-in diameter the die was aligned with the greatest possible precision in order to insure as straight a tube as possible

Jan 1, 1933

By J. J. Ormsbee

Attempts at coal-washing have been made in the southern states during the last twenty years; but it is only within the last four or five years that the practice has become at all general. It might perhaps be claimed as one of the blessings derived from our departed " booms;" for, during their sway, the supply of coal of all qualities, good and bad, could not equal the demand; but, with the subsidence of the inflated demand, came imperative calls for fuels of better quality; and washers, previously regarded as luxuries, became necessities. Among those now in use in this section are representatives of the following types or classes: the trough washer; the jig washer; the percussive table; and those washers in which a constant upward current of water effects the separation. Without having full statistics, it is safe to say that there are in successful operation in the South more washers of the last class than of any of the others. The purpose of these notes is to present data with regard to the constructiOn, operation, and results of one of these current-washers, based mainly on the plant at No. 2 Slope, Pratt Mines, Alabama. The coal is mined from the well-known Pratt seam, having here an average thickness of 3 feet 6 inches. It has distinct cleavage-planes, and breaks in cuboidal lumps; is bright black in color, firm in structure, and air-slacks only after considerable exposure. It burns freely, leaving a gray or buff-colored ash. The lump- and nut-coals are used for domestic and steampurposes (chiefly, however, for locomotive firing), and the slack for making coke. The specific gravity is 1.272. Analyses of Pratt Coal. I. 11. 111. IV. Min. Resources Authority. Phillips. McCalley. of U. s.,1892. Lupton. Fixed carbon,. . 67.90 61.600 64.30 63.82 Volatile material,.. 29.80 31.480 32.08 31.85 Moisture,.,...... 1.508 1.07 1.02 Ash,.... 2.30 5.416 2.08 3.31 Sulphur,. .. 0.83 0.918 0.47 0.70

Jan 1, 1896

By Philip N. Adler, Harold Margolin

Univariant equilibria between the Ibcc, IIhcp, and UIfee phases of thallium have been determined and indicate a triple point at 110°C and 37 kbars. Calculated II —I transformation curves are compared with the experimental. Transformation volumes and/or enthalpies are calculated and enthalpies are compared with available data. ThE triple point of solid thallium has been reported by Bridgman as 153°C and 38 kbar.' More recently, Jayaraman et at.2 have reported the triple point as near 115°C and 39 kbars. Meyerhoff and Smith,3 assuming the elevated-pressure modification of thallium is fcc, as Kaufman suggested,4 and that it is continuous with the room-temperature fcc phase in the Tl-In system, have used pressure data up to 5 kbars to predict the triple point at 162°C and 35.8 kbars. Piermarini and weir5 have indeed found the elevated-pressure phase to be fcc. The effect of variations of pressure and temperature in the IIhCp — Ibcc transformation in thallium have also been reported by werner6 and more recently by Ponyatovskii.7 The work reported here is part of an investigation of the effects of temperature and pressure on the Tl-In system. I) EXPERIMENTAL PROCEDURE The onset and progress of transformation were determined by changes in resistance. A commercially available tetrahedral-type pressure apparatus was used. Specimens of 0.060 in. diam, representing 0.63 pct of the cell volume, were encased in AgCl and mounted in pyrophyllite, as shown schematically in Fig. 1. It can be seen that the specimen is in series with the graphite furnace. Resistance changes of 0.1 pct could be detected with a Kelvin bridge. Resistance of the sample was of the order of 1 milliohm. Other pertinent details in regard to calibration and cell-assembly design are given elsewhere.' Temperature calibration of the cell was carried out in two ways as a function of input wattage. Through a hole drilled in the graphite furnace, a chromel-alumel thermocouple was inserted into the AgCl to a point 0.010 in. from the sample, with the

Jan 1, 1964

By W. C. Hagel, H. J. Beattle

DURING an earlier examination of high-temperature alloy, A-286, the presence of an unknown intermetallic compound was verified by X-ray diffraction. Owing to its prominent appearance at grain boundaries, the arbitrary name of G phase was assigned.' Low-silicon, vacuum-melted heats were found to contain no G phase, and this investigation was initiated to determine the influence of silicon on G-phase formation; additional work was undertaken to extend existing data on other intermetallic compounds and the aging reactions in this group of alloys. Taylor and Floyd2-4 observed that the Ni3Al phase (y') and the Ni8Ti phase (7)) are the only equilibrium intermetailic compounds in nickel ternary alloys containing up to 25 pct Cr and 10 pct Ti or Al. They found that y' can dissolve considerable nickel, chromium, and titanium, although the stoichio-metric composition of 7 remains fixed. Nordheim and Grant5 confirmed that age hardening of 80 pct Ni-20 pct Cr alloys of the Nimonic-80 type is due to precipitation of y', where aluminum is partially replaced by titanium. They suggest that optimum hardness and ductility result from increasing the titanium to aluminum ratio toward the end of the y' solubility range and from increasing total titanium and aluminum content to the maximum limit permitted by processing. Such information is necessary for those seeking to improve the service-temperature range and long-time structural stability of high-temperature components. Experimental Methods Compositions of materiais studied. are listed in Table I. Alloys D, E, and F possess representative A-286 analyses; silicon increases from less than 0.02 to 1.75 pct in alloys A to H; in alloys I to K, titanium decreases from 2.24 to 0.39 pct, and aluminum increases from 0.1 6 to 240 pct. Alloys A and D were solution heat treated for 4 hr at 1700°F, oil quenched and aged for 0.5, 2, 6, 12, 30, 70, 200, and 1000 hr at 1200°, 1300°, 1400°, and 1500°F. Therefore, a total of 33 specimens was required for each

Jan 1, 1958

By M. C. Cheney

The active development of the vast East Texas oil field, the attendant effects of the rapidly increasing flow from its prolific wells and the efforts to bring order out of chaos precluded or dwarfed other oil development in Texas during 1931. In a paper by Dr. F. H. Lahee1 presented at the October, 1931, meeting, the early history of the East Texas oil field is described and the sequence of events in connection with its development and efforts to control its production up to Sept. 25 is narrated. At that time the Railroad Commission of the state reduced the production of the field to a maximum of 400,000 bbl. per day by restricting the allowable daily production per well to 185 bbl. By further reduction in the daily production per well to 100 bbl., the field was held below that maximum figure during the remainder of the year. Meanwhile, as a result of an injunction against the Railroad Commission, its authority in the field was superseded on Oct. 13 by the Governor of the state, and after that date production was controlled directly by his orders issued under authority of martial law. Suits to contest this authority were brought in the Federal courts and were pending at the close of the year. On March 5, 1931, as a result of the East Texas production, posted prices for Mid-Continent 40' A.P.I. crude slumped from $1.07 to $0.67. As East Texas production continued to mount, posted prices in East Texas were reduced to $0.37 on June 3 and $0.22 on July 8, although in that field most of the oil was sold for much less, bringing the producer and royalty owner as low as $0.025 per barrel. Northeast Texas To the information contained in Dr. Lahee's paper, it can now be added that the East Texas field has produced over 105,000,000 bbl. and registered about 3700 successful completions during 1931. There may be some merit to the recent prediction that a large part of the field will have passed its flowing period by the middle of 1932 unless

Jan 1, 1932

By H. F. Yancy

PooR results in coal washing and in ore concentration are sometimes attributed to the shape of the particles in the feed. It is well known that the shape of a particle influences its rate of fall in water. This is evidenced by the value of the constant C in the Rittinger equation for the velocity V of settling in water, V = C-D(d- z ), where C has the following values: 2.73 for roundish grains, 2.37 for long grains and 1.92 for flat grains. This report, which is based upon data obtained during the course of coal-washing investigations conducted by the U. S. Bureau of Mines in cooperation with the College of Mines of the University of Washington, gives the results of a method or procedure of screening in which the particles are separated into three shapes and shows the deportment of these shapes when coal is treated on a coal-washing table. The method consisted in first screening the coal with Tyler standard square-hole sieves, followed by screening tests of each of these products with screens of rectangular opening. For this purpose Tyler "Ton-Cap" screens were used; each square-hole product was subsequently sized with two Ton-Cap sieves so selected that their shortest dimensions were approximately 75 and 50 per cent., respectively, of the opening of the square-mesh sieves. For example: A product which is through 8 mesh (0.093 in.) and on 10 mesh (0.065 in.) is screened on slotted sieves which have openings 75 and 50 per cent. of the 0.065-in. opening in one direction and an opening of not less than 0.065 in. in the other direction. For convenience in discussion, the particles retained on the first slotted screen are termed "cubical"; those retained on the second slotted screen are termed "prismatic" and those passing the second screen are called "flat." (See Fig. 1.) The square-mesh screens separate particles according to two dimensions, length and breadth; the slotted screens divide them further according to the third dimension, or thickness. Prismatic particles have a mass of about two-thirds, and flat particles of about one-half, that of cubical particles of the same square-mesh size. The screen-

Jan 1, 1931

By J. A. Herbst, G. E. Agar

The effect of fluid viscosity on the classification of solids in a liquid-solid cyclone was investigated. The separation size was found to be proportional to Additionally, it was found that the prediction of flow rate through a cyclone is dependent on a Reynolds criterion. Above a critical value, the flow can be predicted by a simple equation, whereas, below this value a variable orifice coefficient must be introduced. INTRODUCTION The solid-liquid cyclone is widely used as a device for classification, thickening, and heavy media separations. The more important variables and how they affect the performance of a cyclone are known and have been the subject of several investigations.' In general, these studies have paid little attention to the viscosity and those which have, introduced it through Stokes settling considerations. Systems which contain appreciable amounts of swelling clays exhibit viscosities much greater than water, and in these systems the viscosity term becomes important in determining the separation size. The work described here was done to determine in a Newtonian system the dependence of separation size on viscosity. BACKGROUND The separation size for a cyclone classifier has been related to the parameters of the cyclone by an equation of the form: where a is probably between 1.3 and 1.5, ß is between 0.50 and 0.57, and 6 has a theoretical value of 0.5. where y has a value between 1.8 and 2.0. Although these relationships are empirical, equations that differ only in the exponents have been derived from theoretical considerations. Those interested in the origin of these equations are referred to some of the original work.6,7 MATERIALS AND PROCEDURE The laboratory apparatus used in this study is pictured diagramatically in Fig. 1. Feed slurry was pumped from an agitated 15-gallon plastic tank by a centrifugal pump driven by 3/4 hp motor. The static pressure of the feedstream and thus the pressure drop through the cyclone was measured on a gage located as close to inlet of the cyclone as possible. When samples were not being taken, overflow and

Jan 1, 1967

By D. G. Westlake, E. S. Fisher

The habit planes for zirconium hydride precipitation in crystals of a zirconium have been determined at various hydrogen concentrations. The (10 • 0)planes are the predominant habit planes; some (10 • 5) and (10 -1) planes were observed after charging conditions which pevmitted formation of a surface layer of hydride. No platelets zrlere observed parallel to any of the twinning planes. Mechanisms for em-brittlement due to hydride precipitation are discussed. LANGERON and Lehr1 found, in 1956, that zirconium hydride precipitates in zirconium in platelets lying parallel to (10.0) slip planes. In 1960, Kunz and Bibbz reported observing the platelets in three different families of twinning planes, (10.2) {11.1), and {11.2), but never in the slip planes. The present study was undertaken to ascertain the cause of these seemingly contradictory results. EXPERIMENTAL Two specimens of iodide zirconium were used in the experiments. Specimen I was a single crystal, while specimen II contained three grains. Grain growth was accomplished by the technique of Lange-ron and Lehr. Three faces were ground on specimen I; the first was 2 deg from the (00.1) basal plane, a second was 2 deg from the (10.0) prism plane, and a third was 4 deg from the (12.0) plane. One face was ground on specimen II such that the poles of the surfaces of crystals A, B, and C were as shown in Fig. 1. After the faces were ground on 600 grit silicon carbide paper, they were chemically polished by dipping in a solution of 8 parts hydrofluoric acid, 50 parts nitric acid, and 50 parts water. This removed all cold worked metal from the surface. The samples were charged to various levels of hydrogen content by heating in hydrogen gas which had been purified by reaction with uranium powder. The various charging conditions are shown in Table I. Specimen I was heated to the reaction temperature at the indicated hydrogen pressure and allowed to react until essentially all the hydrogen was used up. Then the temperature was raised for homogenization. Specimen II was charged by making periodic addi-

Jan 1, 1962

By B. A. Joyce, R. W. Bicknell, R. J. Bennett, P. J. Etter

Epitaxial layers of silicon have been grown on single-crystal quartz and alumina by two types of chemical reaction the hydrogen reduction of trichlorosilane and b) the pyrolysis of silane. These reaction systems are described. The cqsfallography of the two systems, as determined by electron and X-ray diffraction, is discussed, and epitaxial mechanisms suggested. The electrical behavior is briefly considered, and the design and properties of field-evert devices fabricated in the epilaxial material are also discussed. RECENT work carried out in these laboratories" has shown that it is possible to obtain epitaxial deposits of silicon on single-crystal quartz and alumina. The purpose of this paper is to describe the method of preparation of these layers using both the hydrogen reduction of trichlorosilane and the pyroly-sis of silane, to compare the crystallographic behavior of films on the two substrates, and to present some initial results of the electrical behavior of silicon layers on alumina. The structural study has been carried out using electron and X-ray diffraction and electron microscopy. The electrical assessment has been made in terms of conductivity and mobility determinations by the van der pauw3 technique, and by measurements on metal-oxide-semiconductor assemblies. 1) FILM PREPARATION Both quartz and alumina substrates, approximately 1 sq cm in area and 0.4 mm thick. were prepared from slices cut parallel to within a few degrees of (11.0), (10.0), and (00.1), and polished mechanically down to about 0.3 p diamond grade. Chemical polishing of alumina slices, using phosphoric acid at elevated temperatures, has also been used; epitaxial silicon layers have been grown on these substrates, but the process is not entirely reliable, possibly because the large strain present in the Verneuil-grown alumina crystal affects the chemically prepared surface. The two reaction systems are fairly conventional and are described briefly below. a) Trichlorosilane-Hydrogen System. The apparatus is shown schematically in Fig. 1. The substrate was heated by induction, with a fused-quartz encapsulated graphite hemicylinder as susceptor. The procedure for carrying out a deposition was to heat the substrate to reaction temperature in a stream of

Jan 1, 1965

By K. R. Evans

The deformation mechanisms occurring in polycrys-talline, commercially pure titanium and a Ti-8 pct A1 alloy have been investigated and compared to earlier results by Levine on high-purity titanium single crystals and by Conrad on commercially pure titanium. In accord with Levine, two consecutive deformation mechanisms are observed to exist below 500°K with the transition temperature between mechanisms, Tc, strongly dependent upon interstitial composition. T, is found to be 210°. 375° -430°, and 450°K for alloys A large number of investigations have been conducted to determine the rate-controlling mechanisms of plastic deformation occurring in fcc and bcc metals. Very few investigations of a similar nature have been conducted for hexagonal metals. In fact, until very recently, magnesium is the only hexagonal metal which has been systematically investigated for determination of the rate-controlling deformation mechanisms.1"3 From these investigations, it was concluded that basal slip below 420°K occurs by the intersection of forest dislocations,1'3 while for prismatic slip the Peierls mechanism is rate-controlling at low temperatures with interstitial compositions of 0.024, 0.42, 0.61, and 1.13 at. pct expressed in terns of oxygen equivalents. The low-temperature mechanism is found to be an impurity obstacle mechanism in contrast to Levine's earlier conclusion of the Peierls barrier. Measurement of the activation parameters for deformation and estimation of the force-distance profile of the obstacles show their retarding force to be effective over longer distances from the obstacle as the interstitial composition increases. and thermally activated cross slip at higher temperatures. 2 The potential technological importance of titanium alloys has prompted recent studies of the deformation and fracture characteristics of titanium and its alloys. 4-8 Levine' systematically investigated the low-temperature deformation behavior of high purity titanium single crystals oriented for either basal or prismatic slip. It was concluded that the Peierls mechanism was rate-controlling at temperatures below 210°K, while above this temperature an undefined mechanism was rate-controlling. Conrad 7,8 concluded from an analysis of the composition dependence of the critical shear stress at 0°K and measurement of the activation parameters that the low-temperature deformation of titanium is controlled by an impurity

Jan 1, 1969

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

THE increased demand for titanium alloys with improved high-temperature creep strengths has stimulated interest in silicon as an alloying addition to titanium. Silicon is a potent solid-solution strength-ener and, if added in sufficient concentration and properly heat-treated, can also dispersion-strengthen titanium by eutectoid decomposition.' However, better understanding of the nature and distribution of the resulting silicide dispersion in more highly alloyed titanium matrices is necessary for the development of useful titanium alloys which utilize the latter strengthening mechanism. This note describes the chemical and crystallographic characteristics of the silicide phase as it occurs in a typical high-temperature near-a titanium alloy matrix. Several Ti-6A1-3Sn-3Zr a11oys containing various amounts of silicon ranging from 0.1 to 1.0 pct were melted as 10- to 20-lb ingots and processed into 1/2-in.-diam bar stock. The microstructures of specimens annealed at various temperatures were conveniently summarized by the (Ti-6Al-3Sn-3Zr)-Si pseudobinary phase diagram illustrated in Fig. 1. Comparison with the Ti-Si equilibrium diagram indicates the substitutional solutes (Al-Sn-Zr) increase the eutectoid temperature and decrease the a terminal solubility. Annealing at temperatures sufficiently high to dissolve the silicon in a ß solid solution and cooling rapidly enough to preclude coarsening generally produced a uniform dispersion of fine silicide particles, whereas annealing at temperatures near but below the ß transus produced relatively coarse silicide particles. Annealing in the limited a, plus 3 region produced a duplex coarse and fine silicide array. Several a-annealed specimens were examined by X-ray diffraction to determine the crystallographic identity of the precipitate phase. Copper Ka X-ray diffraction patterns of bulk specimens which contained 0.5 and 0.8 pct Si were virtually identical to that of the silicon-free Ti-6Al-3Sn-3Zr base alloy except for a slight shift in some of the high-angle diffraction lines. Apparently the silicide volume fraction was too low to be detected in bulk specimens. X-

Jan 1, 1969

By S. D. Dahlgren

The plasticity of unalloyed P plutonium was studied by evaluating the strain-rate-hardening exponent, m, in the equation Values of m up to 0.33 and tensile elongations up to 680 pct were obtained for ß plutonium formed directly from the a phase. Casl bars that were cycled and tested had lower flow stresses and higher values for than uncycled bars , hut their total plastic elongations were not as great as expected because of premature failure at voids formed during cycling. Flow stresses were higher and m was lower (m = 0.15) for 9 plutonzutn formed from the y phase. ThE strain-rate-hardening exponent for plastic flow of p plutonium was determined as a function of strain rate, test temperature, and heat-treating history, and it was related to the rather large plastic elongation found previously for some plutonium tensile samples. Gardner and ~ann' obtained tensile elongations of up to 620 pct for P plutonium samples which had been completely transformed from the low-temperature a phase to the P phase before testing. Such a large percentage elongation is unusual for unalloyed metals or single-phase alloys.' The a phase is stable below approximately 112°C and (3 is stable between approximately 112" and 190"c.~ Both phases have mono-clinic structures. A temperature of 160°C is 0.58 of the effective absolute melting point, 475°C) of the p phase. The effective melting point is obtained by considering the enthalpy and entropy changes associated with the higher-temperature phase transformations and it is not the same as the experimental melting point of the highest-temperature allotrope of unalloyed plutonium. Nelson, Bowman, and Bierlein observed a striking difference between the ductility, as well as other mechanical properties, of p plutonium formed from the next higher-temperature phase (y) and the ductility of /3 plutonium formed from the a phase. The total elongation of /3 plutonium formed from the y phase was less than 5 pct. Earlier, the creep rate of 13 plutonium formed from the a phase was shown to be 200 to 500 times faster than the rate for 0 formed from y for the same test temperature and stress.

Jan 1, 1969

By E. L. Estabrook

Oil companies operating in foreign countries have made increased use during 1930 of cooperative agreements in prospecting unproven territory and in developing proven territory. A considerable proportion of the existing foreign fields are held under single ownership and have been developed as units. The operating companies seek to maintain this condition by acquiring land in large blocks or by merging smaller concessions under unit operating agreements. Your committee has secured a number of reports on foreign non-competitive operations and a valuable formal paper which deals with the Golden Lane of Mexico.l 0. B. Knight has drawn some valuable comparisons concerning costs of development and ultimate production between a certain competitive area and another noncompetitive area along that strip of rich producing territory. After discussing details of production, numbers of wells and cost of drilling and production, he concludes that the 93,700,000 bbl. of competitive oil will have cost $0.193 per barrel as compared to 85,700,000 bbl. of noncompetitive oil at $0.059 per barrel. The saving of $0.134 per barrel amounts in round figures to $11,500,000, which is 21/2 times the total cost of developing the non-competitive block. The cost for drilling and development of the two areas of 3550 acres which Mr. Knight compares was $18,150,000 under competitive and $4,760,000 under noncompetitive conditions. The estimated ultimate production of the competitive 3550 acres is expected to reach 93,700,000 bbl., or 8,000,000 bbl. above the noncompetitive block. Under ordinary production methods it is to be expected that a noncompetitive area will yield less oil per unit area than will a similar competitive area, because of closer spacing and more rapid extraction in the latter case. The advantage of noncompetitive conditions, in this regard, is that the undivided ownership makes it possible to apply repressuring as a production method fairly early in the life of the field and thus, in the end, to vastly increase the yield. In the particular region described by Mr. Knight, repressuring is not thought to be a factor of

Jan 1, 1931

By Lloyd Jones

THE strip industry made rapid strides in regard to both width and gage until about 1922, when the maximum width was about 20 in. In the hot mills, strips of thin gages in wide widths could be pro-duced, but only at a sacrifice of length of coil, con-siderable increase in power, and decreased tonnage out-put on the min. Hot mills, like the Bray sheet mill and the modern strip and skelp mills, demonstrated that . wider strip could readily be rolled, if such a product was desired. The strip manufacturers were really limited in width, not by the hot strip, but by the cold rolling of wide strip. This factor was roll pressure. The diameter of rolls increased as the width of strip increased. For cold rolling strip 20 in. wide, cold rolls were approximately 20 in. diameter. As the rolls became larger, the arc of contact between the rolls and the strip increased approximately, according to the formula, b=\/Rd where b = the width of contact R = roll radius d = total reduction Now the crushing strength of cold steel of low carbon varies from 70,000 to 100,000 lb. per sq. in. With each succeeding pass the crushing strength increases and may approach 250,000 lb., according to the total reduction. The total reduction in cold rolling of low-carbon steel will range from 40 to 70 per cent of the original thickness, usually in about three or four passes. On this basis, assuming a reduction of 20 per cent in one pass, the crushing strength of steel assumed at 120,000 lb., we have a total pressure between rolls, which (assuming that the rolls do not deform) equals: Roll Strip Strip Diameter, Width, Thickness, In. In. In. Pounds 10 10 0.100 380,000 20 20 0.100 1,080,000 30 36 0.100 2,375,000 42 50 0.100 3,900,000 These figures are approximate, but you will note that in increasing the width five times, or 50 in., the total pressure between the rolls increased approximately ten times. In other words, the pressure per inch of width increased from 38,000 to 78,000 lb. for the same per-centage of reduction.

Jan 3, 1928

By Stanley Herold

A FEW notes on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of, the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east: of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others. are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. (3.04 to 6.09 m.,) apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the rim-cut- with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there are two or three explosions in about 3' minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the sedimentary strata not` far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases.

Jan 7, 1919

By J. P. Sheehan, W. R. Hibbard, M. Baeyertz

This paper deals with molybdenum modifications of 5140 steel that have the same hardenability but a better tolerance for phosphorus than the AISI-SAE 5140 grade. Lack of toughness in steels with higher than normal phosphorus contents is well known to metallurgists. This problem is troublesome even within normal phosphorus ranges, if the heat treatment or the design of the part or the service is critical. Under such unfavorable conditions and also in the case of phosphorus contents toward the upper side of the commercial range, the use of molybdenum to replace a part of the chromium in 5140 steel provides a factor of safety. The toughness of steel is variously exhibited in different mechanical tests; broadly the term is applied to the capacity of the steel to deform prior to fracture. Defined in this way, toughness is considered to be an inherent quality that depends upon the composition and structure of the steel, and also upon its temperature during deformation and fracture in the test. In the present state of our knowledge, the type of mechanical test needs to be included in any discussion of toughness, because the revelation of this quality in steel depends on the stress state and rate of stressing imposed by the test. In comparing the toughness of one steel with another by laboratory testing, it has long been customary to use notched tests that impose severe constmint to deformation, and then to test over a range of temperatures to obtain the so-called transition. At temperatures above the transition, the steel fails after considerable deformation and absorption of energy. Below the transition, less energy is absorbed as the steel fails largely by cleavage. The transition range itself is characterized by a more or less abrupt change in energy absorption and type of fracture. The conventional V-notch Charpy impact test has been used exclusively in the work covered by this report. For the steels under study, rather sharp transitions are obtained with this test, at testing temperatures that are easily obtained in the laboratory. The position of the transition on the testing temperature scale provides a rather sensitive index of the toughness of the steel, when the steels under study are similar in character as they are in this work. Turning to the metallurgical reasons for the greater toughness of one steel as compared to another, the authors propose to limit the discussion to the small field under study. Only one structural state is considered, tempered martensite of a hardness of about 28 Rockwell C or 269 Brinell. The study deals first with the loss of toughness in AISI-SAE 5140 steel caused by increasing the phosphorus content from about 0.020 to 0.040 pct. A second part of the work deals with counteracting this loss in toughness by replacing a part of the chromium by molybdenum. A series of molybdenum modifications was studied, in each of which the chromium was reduced sufficiently to duplicate the hardenability of 5140 steel. Phosphorus affects the toughness of steel in two ways. An inherent lack of toughness of phosphorus-bearing ferrite as compared to low phosphorus ferrite has often been noted. Jolivet and Vidall have shown that phosphorus has the same effect in tempered martensite in chromium steels. The other well known effect of phosphorus is to make steel susceptible to temper embrittlement. Temper brittleness is a loss in toughness brought about by tempering steel within a limited temperature interval somewhat below the A1 temperature. In most of the standard AISI-SAE alloy steels, this temperature interval is approximately 850-1100°F. Either of these types of loss in toughness is easily followed by the shift in the transition temperature obtained with the notched-bar impact test. The data to be presented show the beneficial effect of substituting molybdenum for a part of the chromium in 5140 steel with either moderate (0.020 pct) or high (0.040 pct) phosphorus contents. Both the inherent lack of toughness of phosphorus-bearing steel and temper brittleness are counteracted by this use of molybdenum. The work of Jolivet and Vidal mentioned above shows the detrimental effect of phosphorus on the toughness of tempered martensite in the absence of temper embrittlement, as well as the temper brittleness caused by phosphorus. They used two steels, essentially 0.25 pct C-1.4 pct Cr, with 0.044 and 0.013 pct P, respectively. The nonembrittled state was obtained by quenching in oil from 1610°F, then tempering for one hour at 1200°F and quenching in water. In this state the transition temperature range of the low phosphorus steel in the notched-bar impact test was below that of the steel with 0.044 pct P. An additional treatment of 24 hr at 975°F (that is, in the embrittling range) caused both steels to lose toughness, but the high phosphorus steel showed the greater embrittlement. Recently Hollomon2 has published a comprehensive survey and bibliography of the literature on temper brittleness, to which the reader is re-

Jan 1, 1950