Search Documents

By C. Morrow

Deformation studies were performed on tuffaceous rocks fran Yucca Mountain, Nevada Test Site to determine the strengths and coefficients of friction under confining pressures from 10-50 MPa at room temperature. Frictional strengths of 30ºsawcut samples increased with pressure and reached values of around 150 MPa at the higher confining pressures. However, the failure strengths of the intact samples were quite unpredictable. The coefficients of friction ranged between 0.7 and 0.9 for all specimens. These data can be used in conjunction with in situ stress measurements at Yucca Mountain, to evaluate the potential for earthquake activity in the region.

Jan 1, 1984

By H. C. Fiedler

It was recently shown with 3.3 pct Si-Fe containing 0.026 pct S and 0.06 pct Mn that the extent of secondary recrystallization to a cube-on-edge texture is determined by the cooling rate from the solution temperature of the manganese sulfide inclusions.1 With a rapid cooling rate, many small inclusions rather than a few large ones are formed, which leads to increased restraint to normal grain growth and more complete secondary recrystalliza-tion. Strip samples 12 mils thick, rolled from 1-in.-thick slabs that were cooled at 130°C per min

Jan 1, 1964

By Roshan B. Bhappu, Milton F. Lewis, Jean A. McAllister

Several alternatives are available for treating lower grade gold ores averaging 0.04 to 0.10 oz per ton. These include heap, vat, and agitation leaching and may involve conventional zinc precipitation or carbon adsorption-electrowinning systems. Each of these processes have their inherent economic and operating advantages and disadvantages and the selection of the optimum method for a given gold ore is solely based on economic evaluation of the applicable processes. In this paper an effort is made to provide engineering feasibility estimates for the above processes under varying operational conditions such as ore grade and price of gold.

Jan 1, 1974

By L. C. De Jong, J. F. Shirley, M. L. Campbell

The Toquepala concentrator of the Southern Peru Copper Corp., located approximately 720 miles southeast of Lima near the Chilean border, processes 36,500 tons of ore daily containing between 0.50% and 3.00% copper. The molybdenite content in the ore also varies greatly, ranging from essentially nothing to as high as 0.15%. The 1966 yearly averages were approximately 1.20% copper and 0.03 % molybdenite. The three basic problems that plague the opera- tion of any molybdenite recovery plant are all present at Toquepala in large measures. Both the quantity of plant feed and the quantity of molybdenite contained in the plant feed are continuously changing. Even more detrimental to an efficient operation is the fact that the copper mineralization in the feed frequently changes once in every 24 hours and occasionally once a shift. From the point of view of the molybdenite plant metallurgist, there are four distinctive chalcopyrite concentrates and, at least, an equal number of chalcocite concentrates treated in the molybdenite recovery circuit. The various types of concentrates are distinguished mainly by their mineral content and how effectively the copper minerals are depressed by the different reagents used in the circuit.

Jan 9, 1967

By R. R. Sayers

VENTILATION may be defined as the process by which vitiated air of an inclosed or partly inclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level PER CENT. Oxygen 20.94 Nitrogen 78.09 Carbon dioxide 0.03 Argon 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxid, ammonia, ozone traces CARBON DIOXIDE LIMIT For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent. carbon dioxide.

Jan 7, 1926

By R. R. Sayers

VENTILATION may be defined as the process by which vitiated air of an inclosed or partly inclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level PER CENT. Oxygen 20.94 Nitrogen 78.09 Carbon dioxide 0.03 Argon 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxid, ammonia, ozone traces CARBON DIOXIDE LIMIT For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent. carbon dioxide.

Jan 7, 1926

By H. J. Levinstein, W. H. Robinson

A method of chemically polishing silver for metal-lographic examination has been developed. The samples are prepared by polishing on 0, 2/0, and 3/0 paper. They are then polished on 600 micro-cut paper, followed by a final mechanical polish on a cloth containing 5µ diamond paste. The samples are then chemically polished in a solution of 100 cc of saturated chromic acid and 5 cc of a 5 pct HC1 solution. The chemical polishing is performed by swabbing with a cotton ball saturated with the solution. During the chemical polishing, the sample is rinsed frequently in running water. Polishing in this manner for 5 min is sufficient to remove the strained material from the previous polishing operations. The amount of material removed is approximately 4µ/min. The surface obtained is flat and free of pits. Fig. 1 is an interference micrograph of a silver surface polished by this technique. If the solution employed is of improper HC1 content, an interference color film will form on the sample. This film can be removed either by swabbing with a cotton ball saturated with ortho-

Jan 1, 1962

By P. Greenfield, C. C. Smith, A. M. Taylor

The Mg-Zr alloy ZA and Mg-Mn alloy AM503(S) are shown to have a markedly improved resistance to creep deformation after suitable heat treatments. This improvement makes them suitable for certain stress-bearing fuel element components in nuclear reactors. The extent of strengthening is described and an explanation of the behavior of both materials is given, based on a combination of strain-aging and grain growth. The increase in operating temperatures of fuel element components in Calder Hall type nuclear reactors has necessitated the development of magnesium base alloys with a very high resistance to creep at temperatures up to 500°C. Such alloys are not required for fuel element cans, which require high-creep ductility rather than strength, but for can supporting and stabilizing components, which are needed to support the imposed loads without deforming more than about 1 pct in times of up to 40,000 hr. The amount and type of alloying addition made to magnesium for these parts is limited by the necessity of keeping the cross-section to thermal neutrons as low as possible. The alloys must also possess a high resistance to oxidation in CO2. Alloys which have been developed for this application include ZA, an alloy of magnesium with 0.5 to 0.7 pct Zr and AM503(S), an alloy of magnesium with 0.5 to 0.75 pct Mn. In the as-extruded condition these alloys are very weak and ductile in creep but it has been found that they can be strengthened to a significant extent by heat treatment. This paper describes the method of developing a high-creep resistance in ZA and AM503(S), the extent of the strengthening produced and discusses the probable mechanisms of strengthening. TEST MATERIALS Specimens were taken from typical casts of ZA and AM503(S) alloys extruded into 2 1/4-in.-diam bars, supplied by Magnesium Elektron Ltd. Typical analyses of the bars were as follows: The as-extruded mean grain diameter was 0.001 to 0.002 in. for the ZA alloy and 0.003 in. for the AM503(S) alloy. EXPERIMENTAL METHODS Extruded bars of ZA alloy, 2 1/4 in. in diameter and 9 in. long, were heat treated in electrical resistance furnaces in an atmosphere of flowing CO2 containing 50 to 300 ppm water, thereby reducing the extent of oxidation compared with that which would have occurred in air. Heat treatments were carried out at 600oc for times of 8, 24, 48, 72, and 96 hr and material was subsequently both furnace cooled and water quenched. In order to measure the effect of time of heat treatment, specimens were creep tested at 400°C and 336 psi for about 1000 hr. Subsequently, the behavior of material heat treated for 96 hr at 600°C and furnace cooled was tested at a variety of stresses from 200° to 500°C. Tests were also conducted at 200o and 400°C on material in the as-extruded condition for comparative purposes. With the AM503(S) alloy, only the effect of heat treatment at 565°C for 4 hr was examined. It has been shown1 that such a heat treatment produces marked strengthening in this alloy. Tests on this material were conducted at a variety of stresses at 200°, 300°, and 400oc with comparative tests on as-extruded material at 200o and 400°C. The creep tests were carried out on machines using dead-weight loading and direct micrometer strain measurements on specimens 5 in. long and 0.357 in. diameter. At temperatures of 400° C and below, the creep tests were conducted in air, but at higher temperatures an atmosphere of CO2 was used. Grain size measurements were made on ZA in the extruded and heat treated states and on each specimen after creep testing. This was done by a line count of a minimum of 20 grains in two or three random fields in the longitudinal and transverse directions. The same method was used for measuring the grain size of as-extruded AM503(S), but the grain size of the heat treated material was so large that this method could not be employed. For heat-treated AM503(S) the large grained characteristics (between 0.1 and 1 in.) were confirmed by the measurement of individual grains. In the case of the ZA alloy, specimens taken from various stages in the program were analysed for hydrogen by a combustion method. Material in various states was also analysed for the soluble and insoluble zirconium content by dissolving in dilute hydrochloric acid. This technique has been useda for the determination of amounts of zirconium present

Jan 1, 1962

By J. W. Downey, M. V. Nevitt

DURING the course of the present investigation of alloy phases involving transition metals, phases were found in the systems Os-Ta, Os-W, and Ir-Ta. The (Os, W) phase was also recently reported by Raub.1 Pertinent information is given in Table 1. The approximate composition range of sta- bility was determined metallographically on arc-melted buttons that were annealed 72 hr at 1200°C and water quenched. X-ray powder patterns were obtained with a 114.6 mm diam powder camera using filtered copper radiation. The composition for (Os, W) given by Raub (66 atomic pct W) is in agreement with the composition range reported here. However, the lattice constants reported by Raub are: a0= 9.913±0.007, c/a= 0.515. The reason for the discrepancy between the lattice constants reported by Raub and those given here is not known. Acknowledgments The authors wish to thank M. H. Mueller and H. W. Knott for assistance with the X-ray diffraction work, and R. A. Morris for the preparation of the alloys. This paper is based upon work performed at the Argonne National Laboratory under the auspices of the Atomic Energy Commission.

Jan 1, 1958

By R. E. Maringer, A. Schwope

IT has been recognized that oxygen in minute quantities is extremely detrimental to the room-temperature ductility of molybdenum. Early fracto-graphic studies' of the cast metal indicated that oxides are formed preferentially at the grain boundaries. Additional verification of this preferential segregation has been obtained from internal friction studies on poly crystalline molybdenum (average grain diameter varied from 0.039 to 0.065 mm) and from observations of the effect of oxygen on specimens of extremely large grain size. Specimens A, B, and C, of 0.040 in. diameter commercial molybdenum wire (Lot FW 13-40) were heat treated in the vacuum furnace described by Few and Manning according to the specifications given in Table I. Internal friction studies of these specimens were carried out using a low frequency (approximately 1 cycle per second) torsional pendulum completely enclosed in a vacuum tank. As the pressure of oxygen in the heat treating atmosphere changed, the portion of the internal friction vs temperature curves ascribed to grain boundary relaxation changed correspondingly, Fig. 1. The decrease in the damping capacity at high temperatures as the pressure of oxygen in the heat treating atmos-

Jan 1, 1955

By William L. Fink, Dana W. Smith

Approximately two years ago the authors obtained data that indicated that initial precipitation could not be detected by change of lattice parameter in the aluminum-rich aluminum-magnesium alloys. Some of these data were first published in a brief note in Mining and Metallurgy'. Cast specimens were used at that time and they showed initial precipitation relatively sooner than sheet material of the same composition. For this reason a more thorough investigation has been carried out using a homogenized aluminum-magnesium sheet corltairling approximately 10 per cent magnesium. Materials.—The aluminum used in the preparation of the aluminum-magnesium alloy was of high purity, containing less than 0.01 per cent each of iron, silicon and copper. The magnesium was high-purity sublimed magnesium. Preparation of Alloy.—Approximately 4 kg. of the aluminunl was melted in a plumbago crucible in an electric furnace and the magnesium was added. The melt was thoroughly stirred with a graphite rod and fluxed with chlorine gas before casting. The alloy was cast in the form of a sheet ingot in a cold iron tilting mold (approximately 200 by 165 by 40 mm.) and into small chill-cast slabs for chemical analysis (75 by 40 by 5 mm.). The chemical analyses were made upon drillings from the analysis slabs. The analytical methods were those described in "Chemical Analysis of Aluminum," published by the Aluminum Company of America. The composition of the alloy was found to be: magnesium 10.30, silicon 0.013, iron 0.008 and copper 0.005 per cent. In order to insure homogeneity the alloy was given two intermediate anneals at 430' C. for a total time of 36 hr. The ingot was hot-rolled

Jan 1, 1937

By E. H. Hamilton, H. C. Vacher

The limiting concentrations of carbon and oxygen which may CO-exist at equilibrium in liquid iron are important in determining the degree to which liquid steel may be refined before it is deoxidized. Most refining processes depend upon the oxidation of a highly carburized iron which invariably results in contaminating the steel with oxygen. The oxygen thus introduced presents many problems to the refiner, who in turn has attempted to rid the steel of this impurity by deoxidation witch elements such as manganese, silicon and aluminum. The importance of the limiting concentrations of carbon and oxygen is accentuated in view of a number of recent researches which have indicated in many instances the existence of relations between oxide inclusions and dissolved oxygen and physical properties and chemical behavior of steel. The determination of the equilibrium concentrations of carbon and oxygen existing in iron under steelmaking conditions is obviously of fundamental importance. It has been generally assumed that the product of the equilibrium concentrations of carbon and oxygen in liquid iron is a constant and that this product is directly proportional to the carbon monoxide pressure in equilibrium with the liquid iron. Hertyl.2 has computed values for this product based on open-hearth data which are all in the neighborhood of 0.01 to 0.03 (per cent. FeO X per cent. C) for temperatures in the vicinity of 1550" to 1600" C. and one atmosphere pressure. Kinzel and Egan % have attempted to determine the value of this product by exposing liquid iron to carbon monoxide at one atmosphere pressure. The value reported by them was 0.0005 at 1550" C. In order to apply certain equations to the rate of carbon elimination in the open-hearth process, Feild4 found it necessary to assume a value of 0.0102 at 1580" C. for this

Jan 1, 1931

By F. W. Warnaars

The Los Bronces copper deposit is located on the west side of the Andes Mountains in central Chile about 54 km (34 miles) northeast of Santiago. The deposit consists of a hydrothermal breccia complex that was emplaced in the western part of an earlier porphyry copper mineral system. This system exhibits propylitic, sericitic, silicic to potassic hydrothermal alteration with disseminated and stockwork copper-molybdenum sulfide mineralization over an area of about 12 km2 (5 sq. miles). The Rio Blanco Mine, about 800 m (0.5 miles) east of Los Bronces, is an underground block caving mine located in the central part of this system. The mineralization at Rio Blanco is characterized by one of the highest primary copper grades known for porphyry copper systems. Present mining at Los Bronces is from an open pit located in the northern part of a hydrothermal complex that is composed of at least seven different copper-bearing tourmaline breccia pipes. Together these pipe form one large contiguous body about 2 km (1.2 miles) long and 0.7 km (0.4 miles) wide at the surface. This body crops out at elevations of between 3.5 and 4.1 km (2 and 2.5 miles) above sea level. Each breccia pipe has a characteristic shape, matrix, type and degree of mineralization and alteration. Quartz, tourmaline, specularite, anhydrite, pyrite, chalcopyrite, sericite, chlorite, and rock flour are present in significant quantities in most breccia matrices. The clasts consist mainly of quartz monzonite, andesite, and minor amounts of quartz latite porphyry. The seven different breccia pipes are identified, from oldest to youngest, as Ghost, Central, Western, Infiernillo, Fine Gray, Anhydrite, and Donoso. The breccias coalesce, interfinger, or display gradational contacts. In places they form sharp contacts with each other and with the surrounding intrusive or volcanic host rocks. Early breccias are disrupted or cut by subsequent breccia events. Explosive emplacement was followed by collapse after the release of hydrothermal pressures. The Los Bronces breccia complex has sharp contacts with the surrounding intrusive stock and andesites. These contacts dip inward on the north, west, and south margins. The eastern contact is nearly vertical and/or dips slightly outward and suggests a westward tilting of the body of about 15° after emplacement. The breccia complex is not fully explored at depth, but is known to extend at least below the 3 km (2 mile) elevation in its central eastern part, about 1 km (0.6 miles) below the highest breccia outcrop. Primary copper sulfide minerals are most abundant in the Donoso and Infiernillo breccias where the matrix consists mostly of tourmaline, quartz, sulfides, specularite, and/or chlorite with minor amounts of rock flour, sericite, and clay. The volume of the matrix material is mostly smaller than in the other breccias. Secondary enrichment enhanced the primary copper grade in the southern two-thirds of the Los Bronces breccia complex and in much of the surrounding porphyry system. Primary grades of 0.3% to 0.5% copper have been enriched to approximately 0.9%. This enrichment may extend from surface outcrops to a depth of more than 500 m (1, 640 ft) in more permeable parts of the breccia complex. A leached and oxidized capping of variable thickness covers a large part of the enriched layer and exceeds 300 m (984 ft) at one location. The shape and depth of the enrichment blanket and the capping suggest that the enrichment process is still active.

Jan 1, 1983

By M. Garfinkle, W. D. Klopp, W. R. Witzke

The tensile properties of binary W-Re alloys containing up to 33 at. pct Re were determined at temperatures from 78" to 3630°F. Elongations as high as 260 pct were observed in electron-beam-melted tungsten containing 23 at. pct Re when tensile-tested at 3630°F after a 1-hr anneal at 3090°F. All alloys tested under these conditions with rhenium contents between 20 and 28 at. pct exhibited elongations of at least 200 pct. These alloys also showed enhanced grain growth rates. The values of strain-rate sensitivity ranged between 0.2 and 0.3 for the alloys exhibiting high elongations. Houlezler, for swaged alloys tested just above the re-crystallization temperature, strain-rate sensitivities as high as 0.8 were observed. The high-temperature strengths of the high-rhenium-content alloys were also less than those of alloys with intermediate rhenium contents. ALLOYING with rhenium has two distinct effects on the mechanical properties of tungsten. One effect occurs in dilute solid solutions and is most clearly seen in the lowering of the hardness and of the ductile-brittle transition temperature at about 5 at. pct Re.1-3 The second effect occurs in the concentrated solid solution at about 25 at. pct Re, and is characterized by twinning and a larger decrease in the ductile-brittle transition temperature. An aspect of the high-rhenium-content alloy which has received little attention is the higher-than-usual tensile ductility at 3500°F.3 Anomalous high ductility has been observed in several other alloy systems. usually associated with a phase transformation or a solid-solubility limit.4'5 The phenomenon is now commonly termed superplasticity. High-strain-rate sensitivities6 and grain boundary sliding7 have been reported for materials that undergo superplastic deformation. Also, it has been found that superplastic materials usually have a very fine grain structure (less than 10 pm).8 and it has been proposedg that such a structure alone is sufficient for superplasticity. The purpose of the present study was to further characterize the high-temperature tensile properties of W-Re alloys to determine the conditions under which they might be superplastic. Tensile and selected strain-rate sensitivity tests were conducted on alloys containing 0 to 33.3 at. pct Re at temperatures from 78" to 3630°F. Grain-growth rates were also determined on most alloys at 3630°F. Fig. 1 indicates the compositions evaluated and their locations relative to the solvus line in the tungsten-rich end of the W-Re phase diagram. Twelve binary W-Re alloys containing up to 33.3 at pct Re were double electron-beam-melted and subsequently fabricated to 0.3-in. rod by extrusion and swaging. The starting materials were commercial powders of tungsten and rhenium with impurity levels as listed in Table I. The various blended W-Re compositions were hydrostatically pressed at 70 ksi. The pressed bars were drip-melted into 1.5-in.-diam ingots and then remelted into 2-in.-diam ingots at a chamber pressure of 10~5 torr. The ingots were canned in molybdenum and extruded to round bar at a reduction ratio of 6:l. The alloy extrusions were swaged to about an 80 pct reduction at 2100" to 2900°F. Buttonhead tensile specimens with a reduced section diameter of 0.16 in. and a gage length of 1.0 in. were centerless-ground from the swaged bars

Jan 1, 1970

By C. G. Dunn, F. W. Daniels

IN recent publications1-5 the existence and behavior of subgrain boundaries in high-purity metals has been clearly brought to light. Lacombe and Beaujardl by means of special etching methods disclosed in polycrystalline sheets of aluminum the existence of substructures differing in orientation by small amounts (about 1/4"). Boundaries of these structures at relatively high temperatures had the remarkable property' of moving about while the ordinary boundaries remained stationary. Cahn2 also observed substructures in bent and annealed single crystals of aluminum, zinc, magnesium, and rock salt. The position of subboundaries could be explained in terms of a dislocation mechanism of polygonization in which dislocations move into lines at right angles to the bent glide planes thereby relieving elastic stresses in these planes. Guinier and Tennevin8,6 disclosed the further interesting feature that polygonized structures coarsened significantly upon prolonged annealing. Somewhat similar subgrain phenomena have been observed in silicon iron of commercial purity. Although some evidence for the development of macro-mosaic structures in silicon iron already has been reported by one of the authors6,7 under the phenom-enological term "crystal recovery," much better evidence recently has been obtained due to improved etching techniques. In addition, phenomena regarding structural changes have been uncovered. The present investigation is divided into three parts: (1) The phenomenon of Laue spot sharpening on annealing cold-rolled crystals, (2) the phenomena of polygonization and subgrain coarsening The material used in the present investigation was high-grade commercial silicon iron sheet of nominal composition, 3.3 pct Si, 0.004 C, 0.011 P, 0.010 S, 0.04 Mn, 0.01 Al, 0.04 Cu, 0.01 Sn. Large single crystals of this material Were prepared for cold-rolling or bending as scheduled. Cold-rolling of 12 pct was carried out on a laboratory 8-in, diam rolling mill. The bending deformations were performed by pressing the crystals between a solid Fig. 2—lllustrative foue patterns to show Laue spot sharpening. a (Left)—Specimen as cold rolled, b (right)—After 48 hr at 1400°C. round bar and a mating half cylinder, both heavily greased. Individual specimens were cut from the deformed crystals, and the cut edges were deeply etched prior to annealing. Laue photographs were made using 40-kv tungsten radiation. The technique used to disclose the various subboundaries was an electropolish and electroetch in a bath of chrome-acetic acid.' The anodic polishing done at 22 v was immediately followed by etching at a reduced voltage, which was dependent upon the nature of the subboundaries. Phenomenon of Laue Spot Sharpening on Annealing Cold-Rolled Crystals Fig. 1 gives the initial and final orientations of the specimens cold-rolled 12 pct. Each specimen was annealed at a temperature and for a time which caused significant structural changes as evidenced by alterations in Laue patterns. Representative Laue patterns and micrographs showing the essential changes are given in Figs. 2, 3, and 4. The essential points to be derived from these illustrations follow: 1. Annealing at 950°C clearly develops a substructure with the orientation of the cold-rolled specimen. 2. The subboundaries formed obviously separate regions of nearly the same orientation. Some of the subboundaries appear as a sequence of dots similar to those observed in aluminum by Lacombe and Beaujard,' but whether this is due to extremely small differences in orientation is not known at present. 3. The substructure coarsens upon prolonged annealing. 4. Prolonged annealing also causes a decrease in orientation spread according to Laue spot sharpening'

Jan 1, 1952

By Pol Duwez, Paul Pietrokowsky

Titanium and vanadium form a complete series of solid solutions at temperatures above 885°C. Below 885°C, vanadium is slightly soluble in a titanium (about 1.5 pct V at 650°C) and a two-phase a plus ß region extends to 18.5 pct V at 650°C. The alloys up to 15.0 pct V transform into a supersaturated a solid solution upon rapid cooling from the ß phase. Above 15 pct V the ß phase may be retained. The temperature at which the ß to a' martensite-type transformation takes place decreases steadily from 850°C for 0.5 pct V to 325°C for 12.7 pct V. IN the transition series of the periodic table, the six elements that have a body-centered cubic structure at all temperatures, namely chromium, vanadium, molybdenum, columbium, tungsten, and tantalum, fulfill the conditions required for the existence of complete series of solid solutions with the high temperature (ß) form of titanium. Up to the present time, complete solubility at temperatures above the a to ß transformation of titanium has been observed in the systems Ti-MO,1,2 Ti-Cb,2 Ti-W,³ and Ti-Ta.³ The two remaining elements, vanadium and chromium, have atomic diameters which are not as near that of titanium as the atomic diameters of the four other elements. Both are smaller than titanium and the difference, expressed in percentage of the titanium atomic diameter, is 12.3 pct for chromium and 8.2 pct for vanadium. On this basis, the least favorable conditions for solid-solution formation are therefore encountered in the Ti-Cr system. The early work on the Ti-Cr system4 revealed that up to about 1100°C the solubility of chromium in ß titanium is limited, and an intermetallic phase exists near the stoichiometric composition TiCr2. It was found later' that a continuous series of solid solutions extends across the diagram at higher temperatures, and TiCr2 forms by solid state reaction. It became apparent therefore that complete solubility would also be present in the Ti-V system. The present investigation confirms this possibility. The iodide-refined titanium used in this investigation was purchased from the New Jersey Zinc Co., New York. According to the manufacturer, a typical analysis of this product is 0.0065 pct Mn, 0.0022 pct Fe, 0.0015 pct Cu, and 0.0042 pct Pb. The Vickers hardness number (10 kg load) of the crystalline bar varies between 55 and 80. The vanadium metal was purchased from the Westinghouse Electric Corp., Lamp Div., Bloomfield, N. J. The purity of this metal is probably above 99 pct V. The oxygen content must have been quite low, since a bar about 1/4 in. square could be cold rolled into a ribbon 0.020 in. thick. To prepare the various alloys on the titanium-rich side of the diagram, the titanium rod was machined into cups 1 cm in diam and about 1.5 cm high. Pieces of vanadium, of the proper weight, were cut from the square bars and placed within the cups prior to melting. On the vanadium-rich end of the diagram, single pieces of the metals, in the proper weight pro-

Jan 1, 1953

By D. N. Seidrnan

In the present note we present thermal-analysis data for the liquidus curve from 0 to 76 at. pct Se and for the selenium-rich monotectic reaction in the Pb-Se system. We have previously reported that no expey-imental eviderzce was found for a lead-rich monotectic reaction, at -860°C with a monotectic composition of -20.5 at. pct Se, as found by Nozato and Igaki.&apos; Our additional data substantiated this earlier finding and extended the composition range studied. The alloys were prepared from semiconductor -grade lead and selenium purchased from the American Smelting and Refining Co. Both elements were 99.999+ wt pct pure as determined by the supplier. The impurities for lead were Fe (1 ppm) and Cu & ppm) while for selenium the impurities were Cu (< 1 ppm), As (< 1 ppm), Te (1 ppm), and C1 (<1 ppm). The general procedures used for thermal analysis were those specified by the National Bureau of Standards. A Pt/Pt-10 pct Rh thermocouple calibrated against the freezing points of zinc and copper purchased from the National Bureau of Standards and antimony (99.985 pct pure) purchased from A. D. Mackay, New York, was used for all the thermal analysis. The thermocouple electromotive force was measured with a Rubicon Type B potentiometer used in conjunction with a galvanometer with a sensitivity of 0.5 pV (mm) -&apos;. The absolute accuracy of this thermal-analysis system was *0.5"C. One-hundred-gram alloys of the desired composition were sealed in quartz crucibles, with a central thermocouple well, at a pressure of less than 10"1 Torr. The alloys were initially heated well above the liquidus curve and shaken vigorously to insure homogeneity. Cooling curves were then taken by the direct method at cooling rates ranging from -0.5" to 1.5"C (min)-&apos;. The phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis is shown in Fig. l.* An extrapolation of the selenium-rich portion of the liquidus curve to the monotectic reaction isotherm (678.3"C) gave a value of 76.1 at. pct Se for the monotectic composition. A tabulation of all the thermal-analysis data is given in Table I. As we previously reported no experimental evidence was found Fig. l—The partial Pb-Se phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis. For the sake of clarity the points for the 49.00 and 49.16 at. pct Se alloys were not drawn on this phase diagram, see Table I. for the lead-rich monotectic reaction found by Nozato and Igaki.&apos; This result was further substantiated by the fact that none of twelve lead-rich alloys, see Table I, examined for this monotectic reaction exhibited a thermal arrest in the temperature range (849" to 863°C) cited by Nozato and Igaki for the lead-rich monotectic reaction. Hence, our results tend to support the earlier qualitative work of ~elabon&apos; and Friedrich and ~eroux" in the 0 to 50 at. pct portion of the phase diagram, though the selenium-rich monotectic composition and reaction isotherm temperature were in agreement with the approximate values (75 at. pct Se and 672" to 680°C) given by Nozato and ~~aki. &apos;

Jan 1, 1967

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962

By Ö. Valla, A. Muan, K. Grjotheim

The solid miscibility gap between CaO and "FeO" in the system CaO-"FeO" in contact with metallic iron gradually closes as MnO is added as a third component. On the liquidus surface of the system CaO-"FeO"-MnO, this situation gives rise to a boundary curve which originates in the bounding system CaO-&apos;&apos;FeO", proceeds a short distance into the composition triangle of the ternary system, and then vanishes. A new approach has been used to follow the course of this boundary curve. It is shown that the curve vanishes at a much lower temperature and at much lower MnO contents than has been inferred previously. The oxides CaO, "FeO", and MnO together with SiO2 are the major components of the slag phase formed in the basic oxygen process. Hence, the system CaO-"Fe0"-MnO is of considerable technological interest. In addition, the system is theoretically interesting. The three oxides above all have sodium chloride structure. The size differences among the cations are such that in the bounding "binary"* systems CaO-MnO and "FeO"-MnO complete solid-solution series are formed,1,2 whereas in the system CaO-"FeO" there is only limited mutual solubility in the solid state,3 see Fig. 1. Hence, a solid miscibility gap exists in a part of the "ternary"* system Ca0-"Fe0"-Mn0, and a liquidus boundary curve originates at the peritectic point, point a in the insert in Fig. 1, in the system CaO-"FeO", extends a certain distance into the ternary system, and then vanishes. Very little quantitative information on the system Ca0-"Fe0"-Mn0 is available in previous literature. Fischer and Feischer4 sketched isothermal sections at 1600° and 1700°C, and estimated that the vanishing boundary curve extends to approximately 1650°C and a composition of 42 wt pct MnO. The work to be described in the following was aimed at locating experimentally the "vanishing" liquidus boundary curve, determining its end point, and deriving representative isothermal sections below and above the temperature of the end point of this curve. EXPERIMENTAL METHODS The phase relations were determined by the well-known quenching method. (For a description of this method as applied to oxide systems, see the original paper of Shepherd, Rankin, and wright.5) Prereacted oxide mixtures of desired compositions were contained in iron crucibles and heated in a vertical tube furnace in an atmosphere of purified nitrogen. After equilibrium was judged to have been attained, the samples were quenched to room temperature, the phases present were identified by microscopic and X-ray examination, and total iron oxide contents were determined by chemical analysis. "Fisher Certified" reagents (MnCO3, CaCO3, Fe2O3, and Fe) served as starting materials. The calcium carbonate and ferric oxide were heated in air at 400° and 800°C, respectively, for 24 hr prior to use. Manganese oxide was prepared by decomposing the carbonate in a graphite crucible in hydrogen atmosphere at 1000°C. The product was ground under acetone to -100 mesh. The iron powder was used directly without any preparation. Dicalcium ferrite was used as a starting material for some mixtures. It was made by mixing some of the above prepared CaCO3 and Fe2O3 in proportions corresponding to the formula 2CaO. Fe2O3. This mixture was then fired in air for

Jan 1, 1969

By J. Kucera, J. Vreštál

DIFFERENT authors1 &apos; have been engaged in meas-uring the vapor pressure of pure cobalt. The results of their measurements satisfy the expected temperature dependence of vapor pressure and are in mutual agreement, with the exception of the results by De Dyk Man and ~esmejanov.~ The latter authors, by using the effusion method, have achieved considerably higher values than other workers. By using the isotope exchange method they obtained much lower values than other authors. The determination of thermodynamic functions of the binary Ni-Co system was carried out, as far as we know, only by De Dyk Man and Nesmejanov.4 This determination was based on extremely low values of vapor pressure over pure cobalt obtained by the isotope exchange method. Therefore we considered it useful to repeat these measurements. Furthermore, the reliable values of thermodynamic functions should complement the migration characteristics, the inner magnetic field data obtained by Miissbauer effect measurements, specific heat data, and the K effect and positron annihilation characteristics that have been achieved for the Ni-Co system in the Institute of Metallurgy of the Czechoslovak Academy of Sciences in Brno.5-9 The measurements in this paper were performed by the isotope exchange method. In this method, as has been shown by analysis,10-&apos;3 the vaporization rate, w, can be calculated from the relation w = k/1oSw [1] i0Sw) [1] where L, is the activity per unit mass of the source, S is the area of evaporation, k is the tangent at the point t = 0 to the curve giving the radioactivity de-pendence of the target vs annealing time, t, and wis the probability for the tracer atom condensation on the target surface. The value for cc. can be obtained from the equation w = a + 2P(l-a) [2] where P is Clausing&apos;s coefficient and a is the condensation coefficient. In the present work the cylinder shaped containers for annealing the samples were used, characterized by the ratio 1:d = 1.06. Here 1 is the length and d the diameter of the container. For this ratio P = 0.514 and w =0.5, and w is independent of the condensation coefficient. The vaporization rate is related to the vapor pressure p by the relation where R is the gas constant, T is the absolute temperature, and M is the molecular weight of the component investigated. Measurements of the vapor pressure of the i component over the pure metal, p!, and the alloy, pi, at the given temperature and composition enable one to calculate the thermodynamic activity of this component from the equation ai=pi/pi [4] is and the activity coefficient ri=ai/xi [5] xi where xi is the molar fraction of the investigated alloy component. EXPERIMENTAL Evaporization rate measurements were carried out with pure cobalt and eight different Ni-Co alloys, which were kindly delivered by the Centre National de Recherches Me&apos;tallurgiques Liege, Belgium. The composition of the alloys is given in Table I. The cobalt used in these alloys contained the following impurities: 0.016 wt pct Fe, 0.014 wt pct Cu, 0.01 wt pct Mn. Other elements were present in much lower concentrations. From the melts, samples in the form of small cylinders of 12 mm in diam were ma-chined. The thickness of the targets and sources was 2.5 and 1.2 mm, respectively. The lower thickness of the sources was chosen to make their over-all ac-tivity as low as possible. Sources were activated in

Jan 1, 1970