Search Documents

By R. L. Rickett, S. H. Kalin, J. T. Mackenzie

Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By Ta M. Li

This article draws freely on the experiences of the engineering and operating staff of P.T. Inco and its parent firm Inco Ltd. In addition, information was derived from papers presented during the recent International Laterite Symposium, held in conjunction with the 1979 AIME Annual Meeting, New Orleans, La., February 19-21. The author wishes to acknowledge all contributors and, in particular, Roy Aitken, president and managing director, P. T. Inco.

Jan 7, 1979

PROF RICHARD ÅKERMAN Stockholm, Sweden ANDREW CARNEGIR New York, N.Y. DR. JAMES DOUGLAS New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France R.A. HADFIELD Sheffield England PROF HANS HOEFER Leoben, Austria PROF HENRI LOUIS LE CHATELIER Paris France M FLORIS OSMOND Paris, France JOHN E. STEAD Middlesborugh, England PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia CHARLES D WALCOT Washingtion D.C. PROF DR HERMANN WEDDING Berlin, Germany

Jan 1, 1910

In Mr. Weed's interesting paper, frequent reference is made to the Cananea copper-deposits, which are said to have been so vigorously exploited that they produced 14,000,000 Ib. of copper in 1901. The ore-bodies which yielded this large quantity of metal are described as a product of contact-metamorphism, and in Mr. Weed's genetic classification of such deposits, they receive a place under the sub-heading, "Deposits impregnating and replacing beds of contact-zone."* They are considered by Mr. Weed to represent a special type under this head, and are further classified as: " l. Chalcopyrite deposits: (a) Pyrrhotite ores; (6) Magnetite ores, Cananea type." In condensing much information into a comparatively small space, the presentation of a subject may be so abbreviated as to detract from its clearness. The situation at La Cananea, considering its importance from an economic as well as scientific standpoint, may he worthy of more detailed description. As Mr. Weed rightly remarks, " structural differences are so important, and have SO marked a bearing, not alone on the theory of their genesis, hut also on the working of the deposits and a determination of their value as mines, that they merit a full discussion."† It is my present purpose: (1) to show that it is doubtful whether the copper of La Cananea is mined, except to a limited

Jan 1, 1903

By Thomas T., Read

TWO American students entered the Ecole des Mines in 1856, Joseph Lesley of Philadelphia and Thomas Egleston of New York. Lesley remained there only one year, but Egleston completed the whole 'curriculum and received, in 1860, the certificate given to foreign students .in lieu of the official appointment and degree. awarded French students. Returning home he received, in 1861, an appointment by Secretary Henry of the Smithsonian Institution to sort, label, and arrange the collections of mineralogical and geological specimens which had been brought to Washington by the various government exploring expeditions in the West. Thomas Egleston, born in New York City on Dec. 9, 1832, was the son of Thomas Jefferson Egleston, who came to New York from Massachusetts some time before 1829. The first American ancestor of the family had settled near Dorchester. in 1630. T. J. Egleston and Joseph Battell established an iron-merchandizing business* at 166 South St., New, York, which prospered exceedingly; so much so that when Thomas J. Egleston died, July 12, 1861, his estate had a book value of over $500,000. Since an older brother was expected eventually to take over this business, Thomas, who had a liking for science, went to Yale,, where he completed the regular four-year course in 1854, and then remained another year for advanced work in chemistry under Silliman. I One biographer says he went to Europe, . early in 1-856, on account of his health. It was the custom at that time for wealthy young men to make a tour of Europe after completing their academic education. Whatever the precise reason, he began scientific work at the Jardin des Plantes in Paris but soon trans* It still operating as Egleston Bros. Inc., though no direct descendants of its founder are now living.

Jan 1, 1941

By H. L. TERWILLIGER

THOSE of us who have been following rock drilling work for the last 15 or 20 years can recall some of the problems that were encountered with the old piston type of rock drill and the solid steel which it used. There was frequent trouble in keeping a straight hole in badly broken ground when using the ordinary four- point bit that had a flare on the wings of about 14". The drill steel, when pounding down its hole, would follow the line of least resistance and draw away from the desired line when it encountered a weak side in the ground through which it was drilling. Some would overcome the difficulty by making long winged bits to prevent the steel crowding over; this would relieve the troubles to a great extent. There was trouble with the rifling of drill holes and inability to drill round holes in some ground. The cure for these ills was to use the "X" bit, rather than the crossbit. The "2" bits were brought out in an effort to make it easier to drill a round hole in bad ground. Most of these troubles were before the days when the mechanical drill sharpener was in as common use as it is today. It was not until the introduction of the Leyner type of rock drill, requiring hollow steel that the users of rock drills found themselves confronted with more difficult prob- lems than they had ever encountered before with drill steel because the steel had to stand more severe service.

Jan 1, 1924

By M. Deighton, R. N. Parkins

The metals Cd, ,Wg-, Sn, TI, Zn, and Zr reach a peak hardness after a criticfir1 deformation by rolling- and then soften with fwther rolling-, thereby exhibiting wovk softening. Optical metallography on Cd, Mg, and Zn shows that work softening is accompanied by a change in grain size occurring during deformation. The creep of zinc from -1l° to +60°C at stresses in the range of 7.9 to 17.3 kg per sq mm is given by € = e0 -t- Bt + Kt +at6. The third and second rate constcints are related by the equation a = K~ K6 and their stress and temperature dependence can be represented by the equations K = A, . exp - (u, - Bu)/kT. A model based upon the stress activated glide of sub-boundaries is proposed which qualitatively accounts for the metallog-raphic observations. Expressions, which are in reasonable quantitative agreement with the ex-pe~inzental observations, are derived for the creep of zinc. THE term "work softening" has been used previously by Polakowski1 and by Cottrell and stokes2 to describe phenomena where further strain of a deformed material leads to a decrease in flow stress. In both cases, however, the conditions were changed for the second straining. Here, the term "work softening" is intended to refer to a decrease in flow stress after continued straining in the same direction at the same temperature: work softening is the antithesis of "work hardening". Work softening of zinc was reported by chadwick3 and in discussion of that paper Jenkins4 indicated that cadmium also work softens. More recently work softening has been reported5 in two magnesium alloys, -99.5 pct Mg. Chadwick found that the hardness, 0.2 pct Proof Stress and the UTS of electrolytic zinc all increased with progressive cold reductions up to 30 pct and then progressively decreased with further rolling. Gay and Kelly6 used a back-reflection X-ray technique to study the effect of cold rolling zinc and found that although deformations greater than 2 to 5 pct reduction in thickness produced some recrystallized grains, deformations greater than 40 pct caused com-plete spontaneous recrystallization. At deformations greater than 60 pct the material was found to consist solely of recrystallized grains, -20 pm diam, the size of which decreased with increasing reduction and was much less than the initial grain size of the annealed material (-300 pm diam). Similar results were also reported for cadmium, tin, and lead.6 Gay, Hirsch, and Kelly' suggest that these experiments indicate recrys-tallization takes place when the dislocation density exceeds a certain value. However, no measurements of MATERIALS AND EXPERIMENTAL PROCEDURE The purity of the metals used in this work is indicated by the following figures: Zn (99.99); Cd (99.94); Mg (99.95); T1 (99.99). The zirconium was iodide crys tal bar with a probable purity of about 98 pct. The metals were obtained in the form of 0.25 in. thick strip or 0.425 in. diam rod by various fabrication methods and then annealed to ensure complete re-crystallization. Hardness-deformation curves were obtained at room temperature by rolling 4 in. thick strip under conditions which left a surface adequate for diamond pyramid hardness tests immediately after rolling. The hardness was taken as the niean of five impressions made using a 5 kg load and the time elapsing between rolling and making the last impression never exceeded 5 min. The zinc specimens for creep testing were from 3 by 3 by 4 in. cast slabs which were rolled to 0.10 in. thickness starting at 350°C and finishing cold. The resulting strip was cut into pieces 1 in. wide and annealed in batches. With suitable choices of annealing temperature between 100" arid 400°C five different grain sizes varying from 4.54 x 10' to 3.03 x l05 grains per sq cm (530 to 20 um diam) were obtained. Creep tests were done in compression using a sub-press, based on a design after Ford,8 in which the strip is compressed between dies 0.100 in. wide under conditions of plane strain. Since there is no lateral spread of the material, the area of contact between the dies and strip remains constant throughout the test and the application of a constant load, using the load maintaining device of a hydraulic testing machine, resulted in a constant stress. Covering the dies with strips of P.T.F.E. reduced frictional effects to a minimum. The creep strain was obtained by measuring the travel of the crosshead of the testing machine to a sensitivity of 0.1 pct reduction in thickness. The complete subpress assembly was contained in a steel box and for tests above the ambient this was filled with liquid paraffin and heated electrically. Temperatures below the ambient were obtained with a cooling mixture of acetone and solid carbon dioxide in the box. The liquids were stirred and the temperature of the specimen, which was controlled to ±0.5"C dur-ing a test, was measured by a thermocouple placed near the dies. Compression testing of cylindrical specimens was also carried out in the subpress using hardened flat discs separated from the test material by P.T.F.E. sheets which obviated barrelling of the specimens. Various initial strain rates were supplied by the hydraulic testing machine, and the deformation was measured by a clock dial gage resting on the cross-

Jan 1, 1970

By C. Q. Payne

(New York Meeting, February, 1912.) THE art of crushing ores and other materials by means of rolls is a comparatively recent one. While the first record of rolls using iron crushing-surfaces dates back to the year 1806, when they were employed in Cornwall, their principal development has taken place during the last 30 years. To Stephen R. Krom belongs the credit of the pioneer in introducing the belted high-speed roll, which has had its origin and a marked development in this country. His notable contribution to the art was in the use of a single bed-plate or frame supporting the roll-shafts, and to which levers holding the movable roll-bearings were pivoted. He also made use of steel tension-rods to support the crushing-strains, and of hammered-steel tires for the crushing-surfaces. These changes brought the design of crushing-rolls to a high level. Following closely thereon, about 1885, W. R. Eckart conceived the idea of the swivel or ball-and-socket support for the roll-shaft bearings. This is an excellent mechanical conception, especially for bearings held against a spring pressure, and while it may not be necessary for all types of rolls, yet it has been quite generally adopted by other roll-designers, and illustrates the refinement which roll-construction has now reached. Other engineers, as for example, Argall, Vezin, Roger, and Sturtevant, to mention only a few among many, have also given the closest attention to the various details of rolls, such as the frame, springs, bearings, and shafts, and have developed many novel and original designs. It has remained, however, for the boldness and originality of Mr. Edison to extend the field of crushing-rolls in two new directions, and to cause them to exercise new functions. In developing crushing-machinery for his Portland cement works, Mr. Edison constructed ? giant " rolls, having a diameter of 6 ft. and a length of. face of 7 ft.

Jun 1, 1912

By George F. Becker

Complexity of Rock-Fractures.—The strains to which rocks have been subjected are manifestly very complex, and it is entirely safe to presume that every possible mode of deformation and rupture is exemplified. The most superficial inspection of any ordinary mountain region is sufficient to assure the observer that the rocks have been pressed, stretched, bent, buckled, twisted, and shorn. The study of torsional rupture cannot fail, therefore, to throw light on geological phenomena. The question is how areas which have been broken in this manner are to be distinguished from those which have yielded to other systems of forces. Phenomena of Joints.—It is well known that a large part of the more homogeneous rocks and some very heterogeneous rocks are intersected by partings often ailed joints. These partings are frequently flat surfaces even when seen in very large exposures, but are sometimes surfaces of moderate, single, or double curvature. Joint, usually occur in groups, in each of which the several partings are parallel to one another, and several such groups often intersect the same rock-mass. In such cases the different systems make large angles with one another. Nearly all students of the subject of jointing have reached the conclusion that joints are faulted surfaces, the dislocations usually being of small amplitude; and this conclusion receives abundant support from the study of thin sections under the microscope. It has thus been shown that much even of what would be regarded in hand specimens as mere slaty cleavage

Jan 1, 1895

By A. C. Boyle

PaGE I. Introduction.........68 II. Location of the District,....... • 70 .. III. Stratigraphy...........73 Description of the Rocks.......73 Triassic Eruptives (Andesite Flows and Tuffs) ....73 Triassic Sediments (Shales and Slates)..75 Areal Geology ............75 Structure...-.......76 Folds............. 76 Faults..........79 Shear ...........80 Intrusives..........81 Alaskite Dike.........81 Andesitic Intrusion.......82 IV. PetrogRaphy of thE Rock Types......83 Andesite Flows.........84 Tuff 8...........84 Andesite Tuff........84 Rhyolite Tuff.....-.......85 Alaskite-Porphyry.......89 Andesite Dike........91 V. Description of the Mines......92 VI. Metalliferous Deposits ........ 95 Character of the Ores...........97 Mineralogy of the Ores.......97 Metallic Minerals.......97 Microscopic Character of the Ores...98 Secondary Enrichment....... 103 Genesis of the Ores ...........104 VII. The Sulphate Deposits.......109 Gypsum ..... HO Anhydrite......... ,... 110 Barite............ 110 Origin. with special reference to Gypsum....111 VIII. Summary.............. 113 IX. BIblYogRaphY.............114

Jan 1, 1915

By John F. Wiggert

DURING the early years of Homestake operations, shaft signaling from the cage tenders to the hoisting engineers was done by mechanical means. Small steel cables or jointed steel rods were suspended in the shaft compartments and counterbalanced with weights or springs. These cables or rod strings were connected to the mechanically operated gongs at the engineers' stations by means of bell cranks and steel wires. The system was simple and economical and served the purpose well until the mine reached a depth of 1000 ft., then the system became slow and cumbersome and required a considerable amount of muscular effort to operate it with much speed, because of the inertia of the heavy moving parts. The mechanical signaling was superseded by a simple electrical system consisting of a single pair of wires in steel conduit for each shaft compartment. In the shaft at each station a pull switch was connected to the wires. The switches were operated by means of bell cords, which extended from station to station. This electrical system was a great improvement over the mechanical one, but it had one serious drawback, which also applied to the older system; namely, the engineer did not know where a signal originated. Later on this signaling was improved to overcome this drawback, and to give the engineer a positive indication of a signal's origin. In this system a separate return wire from each pull switch is carried to an annunciator at the engineer's station, where it indicates the signal's origin. While the annunciator system used by Homestake is very safe and reliable, it has the inherent drawback of all wire-connected systems in that it is impossible to send a signal from a moving cage. A number of years ago Homestake became interested in the possibility of using some sort of radio transmission for shaft signaling. The company did much experimental work with purely radio signal transmission, but no practical way was discovered to use radio transmission in a mine shaft for signaling to or from a cage. Therefore, all efforts were directed to devising a practical way of using the hoisting rope as part of the circuit. It was realized that the return circuit from the rope would need to be through electrostatic coupling between the cage and the earth or ground sides of the shaft, because the guides would not always be wet enough to make possible good electrical contact between the cage and earth, therefore relatively high-frequency alternating current was chosen as the medium of transmission. Soon a practical system was developed for transmitting an electric current from a moving cage over an electric circuit of which the hoisting rope was a part. A high-frequency electric current is used as a carrier to transmit the signals or mes-

Jan 1, 1941

By G. H. Cutter

SAFETY in mining depends on wire rope to as great, if not greater, extent than in any other industry. Sudden failure of a shaft-hoist rope might easily result in death or serious injury to the operators and workmen, extensive damage to expensive equipment, and a loss in production while repairs are being made. A wire rope is only as good as its component parts. It must be made from wire properly drawn and treated. It must be fabricated on machines large enough and capable of imparting the necessary qualities to meet the stringent service conditions. However, unless the fundamental requirement of good ropemaking is recognized, all other operations, no matter how carefully performed, will not impart reliability and quality to the product. This fundamental requirement is steel that is homogeneous, of high resistance to fatigue, and of a type suitable for rope wire. Most wire-rope manufacturers agree that rope wire should be made from acid-open-hearth steel. It is comparatively easy to meet the same physical properties with basic steel, but such properties are only part of the requirements for good wire. It is absolutely necessary, particularly for rope service such as mining, where reliability is essential, that the wire be uniform throughout its entire length. Most manufacturers feel that this highly important requirement is better met by acid-open-hearth steel.

Jan 1, 1936

By A. V. UDELL

OF all the metals that have from time to time been called the "Wonder Metal," mercury, often called quicksilver, is probably the most deserving of this designation. A wonder metal it must have been to those workers of an earlier day who named it after that Latin god of commerce and gain, characterized as the fleet messenger of the gods and the conductor of souls to the lower world. The word mercury has been used to indicate a carrier of tidings, a bearer of news, a nimble or clever person, a hawker, and a skillful thief. All of these attributes, and more, are recognizable in this metal, the technical terminology of which is "Hydragyrum," meaning water-silver, and from which the chemical symbol "Hg" is derived. Fickle in its occurrence in nature, simple in its metallurgy, illusive in captivity, it serves man in life or death, in war or peace, in commerce, science and arts, in mining, agriculture, and forestry with a versatility found in no other element.

Jan 1, 1929

By PALMER H. TYLER

WHEN the Mid-Continent Section of the A. I. M. E. met at the roof garden dining room of the Tulsa Club on Monday evening, May 13, most of the members present came prepared with a credulity-stretching yarn of some sort or other, gathered from actual experience. Perhaps it was not realized at the time that such anecdotes would eventually burst into print, but while the excellent dinner was appeasing the inner man the word was passed around that informality and spontaneity of expression would characterize the meeting, with the result that the shackles of convention were eventually cast aside and the meeting waxed better and better until the hour grew ,late, and the chairman, L. G. E. Bignell, originator of the idea, brought to a close what was agreed to be a profitable and entertaining evening. The ball was started rolling by Paul Ruedemann of the program committee, who offered the following:

Jan 1, 1929

By M. T. Simnad, C. E. Birchenall, M. H. Davis

The transport mechanisms previously proposed in wustite and hematite have been confirmed by movement of inert markers during the growth of these phases. By similar measurements the mechanism for magnetite has been determined. The rates of growth of multilayer scales on iron, magnetite and hematite on wustite, and hematite on magnetite have been measured. All rates are found to be diffusion controlled under the conditions of the experiments. MANY studies have been made of the rate of oxidation of iron in both the low temperature, film-forming region and the high temperature scaling range. The interpretation of the results has been greatly complicated by the formation of multi-layered scales containing the various phases of iron oxides. In most cases no attempt has been made to determine the composition of the scale and its dependence on time of oxidation in a quantitative manner. However, several recent studies'" have taken this variable into account. It is generally agreed that the growth of thick scales on iron follows a parabolic rate law for the increase of total thickness. In the thin film region agreement has been claimed with parabolic equations of various forms and with logarithmic equations. The discussion here will be concerned only with the formation of scales of considerable thickness, greater than several microns, although some of the conclusions may be applicable to thin films. A brief survey will be given of the solid phases of the iron-oxygen system, the stability of wiistite in bulk and in thin films, the relative densities of iron in the metal and oxides, and the kinetics of forma- tion of oxide scales on iron. New experimental results will be introduced at several points during the discussion, and an attempt will be made to formulate a mechanistic picture consistent with these observations. The experimental techniques are described in an appendix. Iron-Oxygen System Fig. la shows the iron-oxygen phase diagram. Wüstite ("FeO"): The lowest of the oxides has a NaCl type cubic lattice formed by close-packing of the relatively large oxide ions with the smaller iron ions arranged in the interstices. The ionic radius for 0' is about 1.3 A, while Fe++ has a radius of about 0.8A and Fe"' about 0.7A. Its range of existence on the phase diagram is very wide for an ionic material of this type and does not seem to include the stoi-chiometric composition FeO. These deviations appear to be well established as vacancies on iron lattice sites by the comparison of lattice parameters and densities for a series of compositions by Jette and Foote.4 The limits of the field are disputed, but the work which seems most reliable" indicates vacancies in from 5 pct to more than 12 pct of the iron sites. In order for the crystal to be electrically neutral, there must be electron holes which correspond to the formation of trivalent iron ions equal to twice the number of vacancies. Magnetite ("Fe³O4"): Considerable disagreement also exists in the literature about the stable range of the Fe³O4 field. Some diagrams show the Fe³O4 composition to be lower in oxygen than the formula indicates, but Schenck6 gives a diagram from the

Jan 1, 1952

By Frank Milliken

IN September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1007 to 1019. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was dissemi-nated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was prob-ably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a com-plete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof com-prised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. 1, which gives percentages of tonnage and copper content.

Jan 1, 1940

Jan 1, 1892

By Paul M. Tyler

THE farmer pays the phosphate miner! Phosphorus is used in fireworks; goes to battle in military smoke screens, incendiary shells, and tracer bullets; and, in vermin destroying pastes, does its part in the war against insects. A lemon phosphate can be had for a nickel at most soda fountains, and tens of thousands of tons of phosphate rock are mined annually for use in the food industries, chiefly for making monocaleium phosphate baking powder. Sodium phosphate cleaning, washing, and scouring compounds consume substantial quantities: the iron and steel industries buy a few thousand tons yearly to make ferrophosphorus and to balance foundry-iron furnace charges; and even nonferrous metallurgists use a little for phosphor bronze and other alloys. Phosphoric acid, its salts, and diverse other derivatives of this versatile element have countless applications, and industrial outlets are increasing rapidly, especially in the United States. Nevertheless, in this country nearly 90 per cent and in the whole world fully 95 per cent of the phosphate rock consumed is absorbed ultimately in agriculture.

Jan 1, 1938

?AARONSON, ALFRED E, .Vice-Pres, Mid-Co Petroleum Co , Mid-Co Bldg, Tulsa, Okla '18 ABADIE, EMILE R, Min Engr - Box 927, Porterville, Cal '76 ||ABADILLA, QuiRiCo A, Student, Colorado School of Mines, Golden, Colo. '20 ABBOTT, CLARENCE E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co , 1405 Minnesota Ave, Bessemer, Ala. '04 ABBOTT, Louis BENJAMIN, Chief Engr, Consolidation Coal Co-, Elkhorn Div, Jenkins, Ky '15 ABBOTT, ROBERT R Met. Engr, Peerless Motor Car Co, Cleveland, Ohio. '12 ABE, ASAKA Fujita Min Co, Dojima, Osaka, Japan '14 ABEEL, GEORGE H, JR, Cons Min Engr, 633 St Paul Ave, Los Angeles, Cal '18 ABEL, ALBERT E, Mgr., Pittsburgh Dist, Valley Mould & Iron Corpn, 28th St & R R Ave, Pittsburgh, Pa '19 ABEL, W D, Min. Engr. 3897 Sacramento St , San Francisco, Cal. '19 ABELL, 0 J, Pres & Treas, Abell-Howe Co, 332 South Michigan Ave, Chicago, Ill '19 ABERNATHY, G E Willow Springs, Mo '20 ABEY, HIROSHI, Min & Met Engr, Arakawa Mine, Mitsubishi Co, Senpoku-gun, Akitaken, Japan '17

Jan 1, 1923

By Thomas T., Read

DESIRABLE as it is to summarize what has been set forth in preceding chapters, the task can only be approached with great hesitation. What follows represents the personal views of the author at the moment of writing, reserving the privilege to change them on more mature reflection or in the light of further evidence. With that reservation they may be stated somewhat as follows. Education for the mineral industries falls into two categories; general education and technical vocational, using the word vocational not in its usual sense but to signify preparation for specific activities, in which sense a law school is a vocational school. Even at the beginning, as indicated in the first chapter, mineral industry education was partly general and, partly technical and that relationship still persists, because technical education requires a firm basis of general education. Our general American system is to provide free public' general education through the twelfth grade, or completion of high-school work, though there are already many technical vocational high schools, and even in a community where nearly all the young people are preparing for entrance to college there will be some who wish to qualify for employment at the end of the high-school course, or even on completing junior high. Our educational system, therefore, has not only to provide education for those who intend to proceed beyond the twelfth grade but also for those who, for a variety of reasons, may wish or be forced to cease full-time education at any level between the first and twelfth grades. This study has been chiefly concerned with the problem of what kind and how much technical education to provide for those who have completed the twelfth grade and who wish to make their living in the mineral industries. The obvious fact that the mineral industries employ all sorts of trained persons,

Jan 1, 1941