Search Documents

By L. W. Rowe, S. S. Cole

A laboratory bench scale unit is described whereby finely divided chlorinatable residues are held for a short period by a restraining bed of a coarse-grained ore of comparable composition to permit 'flash' chlorination of the high surface area powder. Results on chlorinating a finely divicled titania residue using rutile sand as the restraining bed showed that 92 pct utilization of chlorine and equivalent conversion of TiO2 in the fine residue to Ticl4 were attained with a dust loss of about 3 to 4 pct and an equivalent amount of ch1om'nation of the titanium values in the restraining bed. THE chlorination of coarse grain titaniferous ores; i.e., 20 to 150 mesh sizes in fluidized beds is practiced commercially.' One effective method found for the chlorination of a very fine material in a fluidized bed is the "flash" chlorination technique.' By charging the finely divided charge material into the bottom of an established bed of optimum sized rutile, ilmenite, titanium beneficiate, or even an inert material such as sand, chlorination occurs before the dust can pass through the bed. The major requirement is that the bed be less chlorinatable than the charge. In this process, the charge consists of a finely divided (between one and 50 µ) titania residue obtained from a titaniferous ore beneficiation process. The charge is blended with a 20 pct wt basis addition of 20 to 60 .mesh size low volatile coke (to minimize hydrogen chloride formation) and fed to the bottom of the bed with the chlorine gas stream. A ball check device is used to permit entry of the charge and prevent the bed from discharging when the gas flow is cut off. The coarse pieces of coke serve to reduce compaction in the charge mixture and permit sat]sfactory feeding without plugging or jamming. Feed and gas rates are adjusted to provide for complete reaction of the charge material, with 90 to 95 pct chlorine efficiency, and maintain a gas flow in the range of 0.4 to 0.6 ft per sec. The equipment consisted of a 3-in. diam mullite tube enclosed in an electric furnace. A bow-shaped 3/4 in. Saran tube fed the charge from an air lock type of feed hopper (to prevent the escape of the chlorine gas into feed bin) to the bottom of the bed. The charge rate was set by providing a small awiliary hopper below the feed hopper where a weighed portion of the charge could be discharged in a specified time interval into the main chlorine stream. The chlorine rate was measured by a flowmeter. The reaction tube was filled with a bed of Australian rutile ore, this restraining bed serving two purposes; i.e., it rapidly heated the fresh charge to the reaction temperature and retained the particles in the bed for a sufficient time for selective chlorination to proceed. Due to the fine particle size and open, porous structure of the charge, this reaction was almost instantaneous, and, with proper adjustment of feed and gas rates, very little fine material passed through the bed without reacting and only a very small fraction of the restraining bed was chlorinated. A typical reaction procedure was to fill the bench scale fluidized bed unit with a 1 kg charge of Australian rutile ore analyzing 95.5 pct TiO2, 0.6 pct FeO, a beach sand deposit 40 to 150 mesh size. When fluidized, the bed was approximately 2 ft in depth. The ore was fluidized with a 1:l mixture of chlorine and nitrogen at a rate of 0.40 ft per sec. This gas mixture was necessitated by the comparatively short bed depth; a larger unit, with a deeper bed, could be fluidized with chlorine alone without significant free chlorine loss. Feed rate was 8.0 g per min of beneficiated ilmenite analyzing 85.0 pct TiO2, 2.6 pct FeO plus 1.6 g per min of 20 to 60 mesh petroleum coke. The

Jan 1, 1962

By Antoni Kidybinski

Mechanical properties of the nether roof rocks play a substantial role in maintenance of mine openings. On longwall faces too low strength is a cause of rock- falls which bring about delays in face advance, and hazard to the miners, while too high strength may result in over hanging of roof rocks in gobs, sometimes over a large area, initiating dynamic periodical pressures. Hence, efforts have been undertaken to develop methods of caveability evaluation for proper selection of roof control system and of longwall-face supports. DESCRIPTIVE CLASSIFICATIONS One of the basic qualitative criteria for classification of roof types with different caveability is the criterion of geological structure. The 26-stages scale worked out for conditions of Donetz Coalfield. USSR, by E.T. Proyavkin et al.(l) may be an example of that type of classification. This scale is presented graphically in Fig. 1. The first types of roofs according to this scale are easily caving immediately after exposure of a small surface, while the last be- long to the strongest roofs which over-hang in waste and require artificial fracturing. Observations and measurements carried out also in Donetz mines lead W.T. Davidyanc (2) to following classification: Class I - weak and densely bedded rocks very easily caving after each advance of supports. The roof subsidence over a waste edge is: [ ] where: h is roof subsidence, m M is thickness of the seam being mined, m S is width of an opening, m Class II - medium caveability and small main roof movements [ ] Class III - hardly breakable rocks, thicker beds with higher strength: caving by large blocks. After exposure of larger roof surfaces the movements of the main roof strata may affect an opening. [ ] Class IV - very hardly breakable rocks - thick, monolithic sandstones: they cause considerable difficulties in working with caving. [ ] Class V - thin-bedded rocks featured by the capacity of a smooth subsidence without disintegration into loose blocks with keeping contact between the particular blocks in a bed. In this classification mining with full roof caving is recommended for class I-III and only exceptionally for class IV. In many coal fields, qualitative and quantitative observations of roof rocks behavior have been carried out: as a result relations and characteristics found in certain mines are given. As an example, Kizielov Coalfield data in the USSR given by B.S. Vinokur (3) may be mentioned. In working thin pitching seams man- less system of undercutting the seam by means of rope saw is used there. The author separated four classes of roofs and gave, for every class, the empirical relation between the extracted area and the time of roof stability. The size of the stable area of exposed roof for particular classes is as follows: 120 to 150 m2 (1291 to 1614 ft2 ), 170 to 200 m2 (1829 to 2152 ft2), 250 to 280 m2 (2690 to 3013 ft2 ) and 350 to 400 m2 (3766 to 4300 ft ). For Kuznetz coalfield in the USSR the following classification of roofs was developed at the WIMI Institute in Leningrad: Class I - completely unstable: impact strength in- dex of rock f = up to 1.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide, exposed after shearer's cut holds stable during the time not longer than 5 min. Class II - low stability: f = 1.5 to 2.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and up to 4.0 m (13 it) long, exposed after shearer's cut holds stable during 5 to 20 min. Class III - medium stability: f = 2.51 to 3.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide and 4.0 to 25 m (13 to 82 ft) long, exposed after shearer's cut holds stable from 20 min. to 2 hours. Class IV - stable: f = 3.51 to 4.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and 25 m (82 it) long exposed after shearer's cut is stable during the time longer than 2 hours. Class V - entirely stable: f = over 4.5

Jan 1, 1982

By Thomas T. Read

The purpose of the following research, as originally planned, was to investigate the influence of temperature upon the plate¬amalgamation process. In order to consider the amalgamation process intelligently, it was first necessary to learn the nature of an amalgam. In the performance of this task it was found necessary to consult a large volume of literature and to perform experimental investigations. The conceptions of the nature of amalgams thus obtained have so important a bearing on the amalgamation-process as a whole, as well as upon the possible influences of temperature, that it was advisable to include them in the treatment of the subject. The broader title is therefore used, even though some features of the amalgamation process have been treated very briefly and others entirely omitted, there being nothing new to present regarding them and their development not required for a clear presentation of the matter in hand. I. HISTORICAL INTRODUCTION. Gold was one of the earliest metals known to man. Occurring in the metallic state, it could be picked up in nuggets or washed, as gold dust, front the sand and gravel of streams. Interesting descriptions of the processes employed in early times for the recovery of gold may be found in Pliny's Natural History and in the treatise by Agricola on ores and minerals. But little progress in the treatment of the ores of gold was possible until efficient -crushing machines were devised. This want was supplied by the introduction, about the beginning of the sixteenth century, of the stamp mill to treat the ores of Saxony. Blanket strikes, or similar devices, were used to catch the

May 1, 1906

By Linn M. Farish

SOVIET RUSSIA reserves must be stupendous. In 1937 I. M. Goubkin placed the reserves of all categories it approximately 48 billion barren which was about twenty billion horn Is in excel:, of all the oil produced in the world since 1857. It is not unlikely in fact it is probable, that these huge stores of petroleum may ultimately be proven to exist within the present boundaries of the U.S.S.R. The size of the country is almost beyond imagination it is 2.7 times as big as the United States. Great sedimentary basins exist in all its different geological provinces, much of which are entirely untested and barely prospected. Oil in commercial quantities is actually produced from formations in every period from the Devonian to the Pleistocene. In the Emba region alone, 300 salt domes are known with an estimate of 700 still to be found. Only 22 of the 300 have been drilled and all showed oil. Of the 22 domes drilled six are now producing. There are 400 mapped structures reported in Azerbaijan

Jan 1, 1940

By Alfred H. Brooks

LESS than a decade ago the consumption of coal in Alaska was practically limited to the salmon canneries and the few lode-mines and settlements along the Pacific coast of the Ter¬ritory. The sparse population of the interior depended on the forests, that of the shores of Bering Sea and the Arctic Ocean on driftwood for fuel. All this has changed. The thousands who have sought and mined gold on the Seward peninsula since 1898 have much impoverished the long-accumulated supply of driftwood, and at the same time the constantly increasing demand for fuel, on the part of the placer-camps and steamers, has resulted in heavy inroads being made on the accessible timber of the Yukon and its tributaries. While on the one hand the immediately available store of wood has decreased, on the other the consumption of fuel because of the rapid expansion of the mining and fishery industries and the attendant growth of population has much increased. Alaska, therefore, offers a constantly growing market for coal and other fuels. As the local coal-production has been insignificant, the demand has been met by importations from Washington, British Columbia, and even from Pennsylvania and Australia. Fuel-Consumption Mr. D. H. Jarvis, Collector for Alaska, has kept systematic records of the trade of the Territory since 1903. The statistics of the coal-importations of the past two years are shown in Table I. If data were available for a longer period of years, the increase of coal-importations would be much more striking.

Jul 1, 1905

By Edmund J. Korber, Donald E. Raab, Frank A. Burns

During the early 1960s, the advent of self- advancing longwall roof supports triggered serious consideration by Bethlehem management to introduce the technique of longwall mining at one of our central Pennsylvania coal mines. Although longwall mining was initially justified as a means to cope with the severe roof conditions at our Mine 32 (Watson, B., 1971), the result of the endeavor has been a consistent and reliable level of coal production, first from Mine 32 and then later from Mine 33, over a period of fifteen years. Longwall production from the Cambria Division has been the mainstay of the low volatile coal required by Bethlehem Steel for steel production. Let us review the events that led to this accomplishment, as well as where we stand today.

Jan 1, 1981

By E. P. Pfleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed pressure, see Fig. 2. The

Jan 1, 1952

By Gary E. Parish

TABLE OF CONTENTS Contents I. Introduction II. Purpose of the Paper III. Historical Perspective A. Existing Sources B. New Sources (NSPS) C. Hazardous Pollutants (NESHAPS) D. Enforcement/Judicial Review 1. Title I Enforcement 2. Title III Enforcement 3. Information Gathering E. Summary IV. The Clean Air Act Amendments of 1977 (1977 Act) A. SIP-Related Provisions 1. Section 107(d) - Geographic Boundaries 2. Section 108 - Air Quality Criteria 3. Section 109 – NAAQS 4. Section 110 – SIPs 5. Section 122 and Sections 402 and 403 of P.L 95-95 – Unregulated Pollutants 6. Emission Offsets – Interpretive Ruling (I.R.) B. PSD Provisions - Part C. 1. Regulations Under the 1970 Act 2. The 1977 Act 3. Regulations Under the 1977 Act C. Visibility Protection - Part C, Subpart 2 D. Non-Attainment Provisions - Part D E. Monitoring and Modeling F. NSPS G. NESHAPS H. Enforcement/Judicial Review 1. Title I 2. Economic Enforcement 3. Title III Enforcement/Judicial Review (a) Section 304 (b) Section 307 4. Summary V. Special Problems and Opportunities for the Uranium Industry A. End Use B. Transportation C. Milling/Processing D. Extraction E. Exploration/Discovery F. General VI. Conclusions Appendix A Footnotes

Jan 1, 1979

By J. M. GLEDHILL

IT would doubtless have been felt by many but a few years back that there was little left to be said on the subject of crucible tool-steel, and that something akin to finality had been arrived at in its manufacture and general treatment. Probably such feeling was justifiable when it is remembered that the making of steel in crucibles is by far the oldest method known, dating back from time immemorial, it being indeed impossible to accurately trace its origin and earliest development; but it seems certain that carbon-steel was made and used thousands of years ago for cutting-tools. Proof of this may be seen by the marvelous carvings and workings on the intensely hard stone-work of the ancients, for it would be difficult to conceive by what means, other than with steel tools, such work could have been executed; and it is wonderful to contemplate that steel cutting-tools should have been used so long ago, whilst the principle of manufacturing them-that is, by fusion of iron and charcoal in crucibles-was then in a measure on the sane lines as we work on at the present day. Archaeologists have discovered that the Chinese made steel in crucibles long before the Christian era. " Wootz " steel fabricated in India centuries ago was crucible steel, as was also the celebrated Damascus steel, produced at the forges of Toledo, and, curiously, this latter steel furnishes' yet another proof that "There is nothing new under the Sun," for it is recorded that Damascus steel contained certain percentages of tungsten, nickel, manganese, etc., some of the very elements, in fact, contained in the present modern high-speed steel, so that a latent high-speed steel may be said to have existed

Mar 1, 1905

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

By E. L. Anders

The Mile Six pool is located on the La Brea-Parinas Cullcession of International Petroleum Co., Ltd., in northwestern Peru on the west coast of South America. The reservoir pressure in this pool has been maintained within 200 psi of its initial value throughout its history, and gravity drainage has played an important role in the production behavior. It has now produced 95 per cent of its estimated ultimate recovery. It is estimated that this interesting oil pool will ultimately produce 67 per cent of the initial oil in place and that the resulting residual oil saturation may be as low as 19 per cent of the pore volume (29 per cent of the hydrocarbon pore volume). An evaluation of reservoir rock and fluid characteristics and ultimate oil recovery is presented. INTRODUCTION This study of Mile Six pool was made to evaluate its performance according to latest available information. The production performance of this pool has been discussed in various articles in the past. and the reported behavior has been used as an example for application of computation procedures for gravity drainage depletion' and as an illustration of field behavior under gravity drainage or expanding gas cap drive. There have been wide variations in reported values of initial oil in place, reservoir oil volume factor. connate-water sauration, volume of effective sand, and ultimate recovery because of the paucity of reliable basic data. These various factors have been determined as accurately as practicable with the latest available information, and this evaluation is presented herein. The production history of Mile Six is an excellent example of gravity drainage depleion with effective pressure maintenance by gar injection. GENERAL Mile Six pool was discovered by cable-tool drilling in November. 1927. when well 1996 was completed in the Parinas sand. After slow development with cable tools and sporadic production. the pool was opened to continuous pro(iuction in November. 1933. and develpment was completed with rotary rigs. Pressure maintenance was started in December, 1933. by returning gas to upstructure wells. Most of the development was 'completed by 1937, but some additional wells were drilled in the period 1939-1947. and several old wells were deepened. A total of 46 oil and gas wells and 4 dry holes were drilled on approximately 7-acre spacing. Of the producers. 21 are now flowing. 2 are pumping. 44 are gas input wells. 3 are abandoned. I is a gas well shut in. and 15 are shut in because of non-commercial production or high gas-oil ratio. The locations of all wells are shown on the map of Fig. I. Total oil production on Dec. 31. 1952, was 30,867,373 bbl: cumulative gas production was 22,023,777 Mcf; and 26,410,946 Mcf of gas had been returned to the reservoir. These figures do not include oil and gas lost ill a blowout in January. 1940. GEOLOGICAL DESCRIPTION Mile Six pool is located on the northern end of a structural spur projecting from the La Brea-Negritos uplift.' The spur is probably a reflection of a basement structure. It plunges gently to the north, i broken into a complex series of fault blocks. and contain.; the Verdun Alto. Section Sixteen. and Mile Six pools. The Parinas handstone (lower Eocene!. which is the producing formation in Mile Six. occurs at an average depth of 2,200 ft in the pool and dips north and east at from 15' to 20". The pool covers an area of approximately 350 acres. Mile Six is downfaulted about 600 ft from Section Sixteen pool to the soutb. and a major fault forms its western boundarv. The north and east boundaries are formed by the intersection of the sand top with the water-oil contact which occurs at approximately 2.440 ft subsea. An original gas-oil contact probably existed at about 1.875 ft subsea. Fig. 1 presents the latest structural interpretation of the pool. and Fig. 2 is an isopach map showing thickness of the total Parinas formation above the original water-oil contact. The heavy lints of Fig. 1 are contours on the sand top, and the fine lines are contours on the fault planes. This type of straight-line structural map was developed 1)) International's geologists to reflect structural conditions where the bedding planes dip and have no curvature. 'The La Brea-Parinas Concession is highly faulted by normal fault.. The beds are flat wherever exposed. The Parinas formation is approximately 635 ft thick. and it is etimated that 62 percent II the formation is effective sand. The original oil zone was about 565 ft thick. Fig. 211 presents an electric log showing typical Parinas sand development ill Mile Six pool. The Parinas band in Mile Six i. a well-sorted. medium- to-coal-se-grained. cross-bedded sand with minor lenses of shale and small lenses and pockets of pebble conglomerate. The sand grains are subangular to rounded and consist chiefly of quartz with feldspars. biotite hornblende, and augite as accessory minerals. Because of faulting of the Parinas- formation to the east and north of the pool. there is probably l possibility of a significant, natural water drive in Mile six. The faults within the pool. as indicated in Figs. 1 and 2. are of smaller disI,laceInent and seem to act only , partial barriers to fluid movement within the reservoir. RESERVOIR CHARACTERISTICS Core analysis data are available from five wells. The data were obtained from three wells (Nos. 3401. 3586 and 3719) at the time of their completion and from well 1996 when the original liner was sidetracked and the well was deepened ill 1946. Data from well 2779 were obtained in 1943 from old cores taken when the well was deepened in 1934. From these core analyses. the average porosity was estimated to be 22.6 per cent. and the average permeability to dry ail. was estimated to be 780 and Measured productility indices varied from 3.1 to 71.4 B/D per psi differential. Specific productivity indices varied approximately from 0.1 to 0.3 B./D per psi per ft of sand.

Jan 1, 1953

By C. S. Barrett, A. Smigelskas

There have been no publications of the deformation and recrystallization orientations of the metal beryllium, yet pronounced textures would certainly be anticipated since it is close-packed hexagonal in structure. Having an axial ratio approximately that of magnesium, beryllium probably deforms by nearly the same slip and twinning mechanisms that operate in magnesium, and the textures are likely to be similar or but slightly different from the magnesium textures. In the tests reported below this is found to be the case; the textures are found to differ from those of magnesium only in the details of the scatter from the average orientation. This report covers not only samples rolled at room temperature, but some rolled at elevated temperatures. Since magnesium has been suspected by some investigators of altering its crystallo-graphic deformation mechanism at elevated temperatures, it was considered possible that beryllium might do so and alter its textures accordingly. No pronounced alterations were found, however. Unfortunately, the theory of deformation textures is not in a state of development that permits one to deduce the deformation mechanism from a knowledge of the textures, which means that the similarity of textures at different rolling temperatures, reported here, cannot be taken as definite evidence that the deformation mechanism is actually the same at all temperatures. The general similarity of the deformation textures of magnesium and beryllium also extend to the recrystallization textures of the two metals, judging by the pole figures for recrystallized sheet presented in this report. Samples were prepared in the form of composite sheets made up of small pieces stacked in a pile. Each piece was trimmed with scissors so that an edge was parallel to the rolling direction, dipped in paraffin, and assembled into the pack by aligning it under the cross hair of a microscope. As the desired orientation was obtained on each piece it was secured in place by touching with a hot wire to melt the paraffin. A stack of ten or fifteen pieces was built up in this way, then trimmed to the shape of a T; the portion to be X rayed was then etched to the shape of a wire about 0.045 in. diam with 6N HCl. This method of shaping the sample is a modification of that used by Bakarian on magnesium.' The absorption of the rays in the sample was so slight that it caused no difficulty in interpreting the films. Exposures were made with a 0.030 in. diam pinhole, using molybdenum radiation (40 kv, 25 ma, Type A film at 5 cm, 2 to 3 hr exposures). With the recrystallized specimens it was found necessary to oscillate the specimen so as to reduce the spottiness of the lines. A range of oscillation of 5" was SUB- cient to produce reasonably satisfactory patterns, though the quality was somewhat inferior to that of the deformation texture patterns, and only two degrees of intensity were read from the arcs on the films. Typical photo-grams for each of the deformation textures and the recrystallization texture are assembled in Fig 1. The pole figures were plotted in the usual way with the intensity of the various portions of the diffraction rings estimated by eye. Seven to nine films were made of each sample and each was carefully read in plotting the pole figures. Typical series included exposures with the beam normal to the rolling direction and at 11, 26, 41, 56 and 71" to the cross direction, plus two exposures with the beam normal to the cross direction, and at 11 and 79" respectively to the rolling direction. The rolling was in each case considered sufficient to develop the final texture: the reduction by cold rolling was 84 pct (from 0.0045 to 0.0007 in. thickness), following prior hot rolling in longitudinal and transverse directions and recrystallization; the reduction by hot rolling at 800°C was 90 pct (0.010 to 0.001 in.), following similar prior treatment; the reduction by rolling at 350°C was 88 pct (from 0.005 to 0.0006 in.) after similar prior treatment. The recrystallization texture was determined on a sample rolled at 350" to a reduction of 88 pct (0.0165 to 0.002 in.) after similar prior treatment, then mounted between steel strips to keep it flat and annealed at 700" in an atmosphere of argon. Discussion of Results The results of the X ray determinations are assembled in the pole figures of Fig 2, 3, 4 and 5 for rolling at

Jan 1, 1950

By W. G. Frailing, W. P. Sims

The Lakeview Pool of Kern County, California, was discovered in 1910 with the drilling of Lakeview No. 1 which blew out and produced an estimated 8,250,000 bbl of oil in 544 days of uncontrolled flow. The well has since been known as the Lakeview Gusher. Full exploitation of the pool did not take place until about 25 years later. A total of 112 producing wells were completed in the Lakeview sand through April 30, 1949. As of that date, about 30 per cent of the total wells drilled were still producing, with an average pool production rate of approximately 2000 bbl per day. The cumulative oil production was about 41 million bbl of oil, or 55.3 per cent of the tank oil originally in place. The pool is bordered on its down-structure side by a body of inactive edgewater and water production where present has been principally the result of coning. Since the depletion of the greater portion of the gas energy by the Lake-view Gusher, the pool has operated under gravity drive. Relatively high angle dips, good permeabilities and favorable fluid characteristics have made gravity drainage particularly effective. Since January, 1942, the oil recovery -has been relatively constant at about 53,000 bbl per ft drop in fluid level. Correlations between the volume of reservoir space drained and the cumulative oil produced indicate that an ultimate recovery of 63.3 per cent of the tank oil originally in place is attainable. INTRODUCTION The Lakeview Pool is an outstanding example of gravity drainage. It is one of many productive reservoirs of the Midway-Sunset Field, and is located in Kern County, approximately five miles southeast of Taft and two miles north of Maricopa, California. Its position rel- ative to surrounding pools and to the Thirty-Five anticline is shown on Fig. 1. The northern portion of the pool lies in sections 32 and 33, Township 32 South, Range 24 East, Mt. Diablo Base and Meridian, while the southern portion lies in sections 25, 26, 35 and 36, Township 12 North, Range 24 West, San Bernardino Base and Meridian. As no two sections bear the same number, they will hereafter be referred to by section number alone. The purpose of this paper is to review the performance of the Lakeview Pool in an effort to evaluate the effectiveness of gravity drive as a recovery mechanism. REGIONAL STRATIGRAPHY AND STRUCTURE The oustanding structural feature is this area is the Thirty-Five anticline, the axis of which plunges South 75" East through the center of Section 35. As shown on Fig. 2, the following zones are oil and gas bearing in the Thirty-Five anticline area: Pleistocene Basal Tulare Tar Sands Pliocene San Joaquin Mya Sands Top Oil or Scalez Zone Etchegoin Kinsey Sand Wilhelm Zone Gusher Sand Calitroleum Sand Miocene Reef Ridge Lakeview Sand Sub-Lakeview Miocene Sands Monarch Sands or fractured shale equivalent Maricopa Webster Sand or fractured shale equivalent Fractured Shale-Uvigerina Zone C Obispo Sand and fractured shale equivalent Pacific Shale Zone The productive interval of the Lakeview Pool is limited to Upper Miocene and Lower Pliocene deposition. In this general area, the most prevalent type of accumulation results from stratigraphic traps or permeability pinchouts. As is the case of the Lakeview Pool, strati-graphic traps resulting from angular unconformities are present. The structure within the Miocene does not parallel that of the Etchegoin (Pliocene), as the Miocene beds were folded, and in places faulted, and subjected to erosion prior to Pliocene deposition. The Lakeview horizon consists of truncated sands which occur on the northeast flank of the Thirty-Five anticline. The direction of strike is west and northwesterly through sections 25 and 36 and continues northwesterly through sections 26 and 33, to the approximate center of section 32. At this point the strike swings to the northeast and the horizon re-enters section 33. in the northwest corner. The change in strike in section 32 affords synclinal accumulation at that point. The Lake-view sand is truncated updip by the Etchegoin overlap. To the southeast, the sand shales out, while to the northwest, the productive interval appears to be limited by a combination of stratigraphic pinchout and permeability barrier. Structurally, the Lakeview reservoir presents three areas of interest, as shown on Fig. 3. Area I in section 32 is a region in which a productive Sub-Lakeview Miocene sand is present. It occurs from 10 feet to 30 feet below the base of the Lakeview sand and attains a maximum thickness of 25 feet in Well No. 21, section 32. The producing characteristics of the Sub-Lakeview Miocene sand differ radically from those of the Lakeview sand. Water production at high structural locations and abnormally high fluid levels indicate that there was no communication with the Lakeview sand. Wells in Area I penetrated this sand and produced it in conjunction with the Lakeview sand. In Area 11, the Lakeview sand is a

Jan 1, 1950

By I. R. Kramer, L. J. Demer

Aluminum single crystals were pulled in an electrolytic cell allowing surface removal during the deformation. The extent of Stages I and 11 of the stress-st-aitz curve was increased and the slope decreased as the rate of metal removed from the surface was increased. An increase of the strain rate caused a decrease in the effectiveness of the metal removal. The data indicate that the work-hardening coefficient in Stage I is determined primarily by the conditions which exist on the surface of the crystal. In Stages 11 and 111, both surface effects and internal barriers are important. ALTHOUGH numerous investigations have been conducted on the plastic flow characteristics of metals in an attempt to explain the mechanism of work-hardening, relatively few studies have taken into account the influence of the surface. In all current theories of work-hardening it is assumed that the impediments to the movement of dislocations are within the crystal. The barriers due to the surface and the existence of solid and liquid films have been neglected even though it has been demonstrated that the surface exerts a large effect. A number of investigators1-l8 have shown that solid films on the surface of single crystals markedly affect their mechanical behavior. In general, the presence of a solid film tends to increase the yield stress and increase the work-hardening rate. Often, on single crystals, Stage I and, at times, Stage II regions are completely suppressed. Various mechanisms have been offered for the effects of oxide and metal films as well as the influence of electrolytes. Of these, concepts concerned with the locking of surface dislocation sources and the blocking of dislocations at the surface resulting in pileups appear to be actively considered at present. Barrett,11 Takamura,6 Gilman,19 Lipsett and King,20 Shapiro and Read,10 and Weiner and Gensamer21 are among those who have interpreted their results in terms of piled-up dislocations at the surface, while Adams.22 and Chalmers and Davis23 have explained their experimental observations in terms of locking of surface dislocation sources. In general, the change in plastic flow properties due to electrolytes has been explained in terms of the unblocking or unlocking of dislocations by the removal of the oxide films. In considering the two proposed mechanisms, it appears that the locking of sources of surface dislocations by a solid film should exert a primary influence only on the critical resolved shear stress for flow and not on the slopes of Stages I and 11. However, the blocking at the surface of dislocations from internal sources may also affect the critical resolved stress and furthermore exert an influence throughout the whole plastic range. In certain cases it does not seem feasible to explain the results of experimental observations in terms of locking of surface dislocation sources. The abnormal aftereffects found by Barrettll,12 by removing the oxide by an acid treatment are excellent evidence of the blocking of dislocations at the surface. Additional evidence in favor of a blocking due to a pileup of dislocations at the surface may be found from the observations that the critical resolved shear strength continues to increase with the thickness of the oxide layer until very heavy oxide layers are formed. If the locking of surface dislocations sources were the dominant factor, the critical resolved shear stress would not be expected to increase after all of the surface sources were locked by the formation of the oxide. This may be expected to happen after a few atomic layers of the oxide are formed. In spite of the above evidence on the strong influence of the surface on the plastic flow characteristic, this has been ignored in current theories of work-hardening. Seeger24,25 suggested that most of the dislocations may slip out of the crystal only when the specimen axis is within certain areas of the orientation triangle. In other areas the resolved shear stress in other glide systems is large enough to generate dislocations which can form Lomer-Cottrell locks, thereby decreasing the average slip distance in some directions and causing a larger hardening rate. Friede126 assumed that at the beginning of Stage 11, a large number of Lomer-Cottrell dislocations are formed by a catastrophic process which used up all the Frank-Read sources on the secondary slip-planes. In this manner a fixed number of Lomer-Cottrell locks is formed which act as barriers against which the dislocations can pile up. In Stage 111, Seeger24 and Diehl, Mader, and Seeger25 proposed that Lomer-Cottrell barriers are circumvented by the cross slip of extended screw dislocations. Cottrell and Stokes,27 Friedel,26 Cottrell,26 and stroh29 suggest that the Lomer-Cottrell dislocations collapse under the stress field of the dislocation pileup. It is the purpose of this paper to report the changes in Stages I, II,and III of the deformation process in

Jan 1, 1962

By AIME AIME

A PAPER prepared by James A. Adams, development engineer of the fitline & Smelter Supply Co., and presented at the last Annual Meeting of the A.I.M.E. in New York City, de- scribed a new automatic pulp density controller which has had a most favorable reception. Manual control has until now been the universal practice in spite of its shortcomings; samples of pulp for density determination were often improperly taken, and only at the operator's convenience, so that the trend in density changes was frequently missed, and the grinding circuit al- lowed to operate under something less than the most efficient conditions.

Jan 1, 1940

By AIME AIME

M ODERN metallurgy properly belongs to this century. The great advance made in this science is directly attributable to the discovery of the Roentgen rays. Application of the results of this discovery, together with the more recent corroborating studies in electronic diffraction have definitely and for all time established this science. Metallurgists today speak with familiarity of the atoms of the different metals in terms of their orientation, atomic volumes, lattice structures, dimensional lattice constants distance of nearest approach, and the like. One matter of profound interest, which is quite staggering to the imagination of the human mind, is the enormity of the number of atoms even in a small particle of metal. As an illustration, let us compute the number of atoms in the volume of one cubic centimeter in a single grain of absolutely pure copper. Eighteen and a fraction cubic centimeters equal the volume of one cubic inch.

Jan 1, 1940

By W. P. Sykes

ThiS investigation was undertaken primarily to establish the relations existing between temperature and mechanical properties in molybdenum, nickel, and an aluminum-copper alloy. Mlolybdenutn (m.p. 2500" C.) was chosen because it is partly similar to tungsten and partly similar to the common ductile metals. Also it is known to furnish, by proper treatment, a desirable material to use in studying relation of grain size and physical properties. The molybdenum used was of the quality that is drawn into wire 0.003 in. in diameter for use as filament supports in incandescent lamps; Chemical analysis shows less than 0.1 per cent. of impurities. Nickel belongs to the same class as iron. Its melting point is 1450" C. and an allotropic change at about 370" C. results in a loss of magnetism above that temperature. This feature made nickel doubly valuable for the purposes of these tests. The nickel used was obtained from the Driver-Harris Co. as 0.090 in. (2.3-mm.) wire, annealed; analysis showed 99.8 per cent. nickel and 0.150 per ccnt. iron. Aluminum is one of the low melting-point metals. Some tensile tests at clevated temperatures have been reported by Bengough but the possibility of learning more with the low temperature and sensitive apparatus available rccommendcd this metal. The samples marked A1 arc an aluminum-copper alloy that contains 3 per cent. copper, 0.42 per cent. iron, and 0.21 per cent. silicon. The presence of the copper somewhat coniplicates the analysis of the results; but the action of copper in aluminum has been studied so that its influence might have been foretold, in part at least. The material and analyses were furnished by the Aluminum Castings Co. The nickel wire, which was deformed at 400" C., was drawn under a bath of molten lead and through a die, which also was immersed in the bath. A thermocouple was suspended in the molten metal to indicate the temperature. Hot oil was uscd as the heating bath for drawing the

Jan 1, 1921

Total U.S. mineral production reached an estimated $17.8 billion for 1960, 4 pct above 1959 and second only to the record high of $18.1 billion established in 1957. As a group, metals achieved a rise from $1.6 billion in 1959 to $2.0 billion this year, an increase of 28 pct. Similarly the value of nonmetallic production including fuels (i.e., natural gas, petroleum, natural-gas liquids, asphalt and related bitumens, carbon dioxide. anthracite. bituminous and lignite coal, peat, and helium) rose from $15.5 billion in 1959 to approximately $15.8 billion in 1960. However, this 2 pct increase in the total value of non-metallic production was due to an increase in the value of the fuels ($11.8 billion in 1959 to $12.2 billion in 1960) which offset a drop in value of the other nonmetallic minerals ($3.7 billion in 1959 to $3.6 billion in 1960).

Jan 2, 1961

By E. W. Davis

I . OPERATING TESTS 1. CHARACTER OF ORE UNDER INVESTIGATION On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite . The magnetite comprises about 35 per cent. of the rock. Fig.. 1 show's graphically that the tonnage of minus 200-mesh material produced varies directly with the tonnage fed to the mill. There is undoubtedly some limit to this relation, but there seems to be no indication of it at 18 T. per hr. Some of the conclusions drawn from this test are that: (a) The ball-mill is naturally a machine of very large capacity; (b) if it is not possible to deliver a large tonnage of original feed to the mill, a closed circuit should be provided so that the mill may crush its own oversize.

Jan 2, 1919

By Richard L. Ashbrook, John F. Wallace

Several high-temperature eutectics of cobalt and nickel alloys were modified by small additions of selected elements. Thes-e alloys were compared to unmodified melts for microstructural variations. A few modified compositions were selected on the basis of structure and their tensile and stress-rupture behavior determined. The results of stress-rupture tests in air at 1800 F and room-temperature tensile tests of four high-temperature eutectics showed modification capable of producing substantial improvements in properties. The microstructures were altered and mechanical properties improved by: a.) dispersing a subordinate phase more uniformly throughout the matrix; b) replacing large continuous -network or platelike constituents with small equiaxed discontinuous phases; and c) by forming new, finely divided phases. tHE term "modification" is most commonly used to describe the refinement in microstructure of the Al-Si eutectic that occurs as a result of rapid cooling from the melt or on slow cooling after treatment with small amounts of sodium.1 "Modification" has also been used to describe the change from flake to spheroidal graphite in the austenite-graphite eutectic of cast iron.2 This change of graphite shape is accomplished by small additions of cerium or magnesium.3 Other systems have also been shown to be capable of modification, for example: Pb-Sn by copper;4 Al-Cu by sodium;5 Al-Mn by sodium;5 and Pb-Sb by aluminum.5 Although modification of Al-Si alloys and cast irons is usually accompanied by improved mechanical properties, a general definition of modification has been suggested to include the effect of small quantities of impurity elements on the microstructures of all eutectic alloys, regardless of the effect on the mechanical properties.6 In this paper, the term "modification" is employed in a broad sense to include the formation of third phases or even the supplanting of one of the binary eutectic phases by a third phase. The mechanism of modification, as for any solidification phenomenon, must be considered primarily in terms of nucleation and growth. Although both nuclea-tion and growth mechanisms are required to explain all the phenomena observed in connection with the solidification of modified eutectics, various investigators have usually favored one or the other.7"16 It has been shown that modification of a binary eutectic can be effected by addition of a solute element that has greatly different distribution coefficients or k values in the two phases of the eutectic. Under these conditions, differences in the temperatures at the solid-liquid interfaces of the two phases retard the growth of one phase with respect to the other.4 It has also been shown that increased undercooling favors a transition from a rodlike eutectic to a globular eutectic.17 A mechanism proposed for the transition from lamellar to rodlike eutectics depends on the concept of constitutional super cooling.18 The modification of eutectic alloys may be of interest for high-temperature service as well as at room temperature. Although "high-temperature eutectic alloys" may appear to be a contradiction in terms, many eutectic systems, including those studied in this work, have melting points in excess of 2400°F. One of the mechanisms by which high-temperature alloys are strengthened is dispersion of a relatively brittle phase such as an oxide, carbide, or an inter-metallic compound throughout a ductile matrix. For a given volume fraction of dispersed phase, strength is increased by decreasing the size and spacing of the dispersed particles.19'20 Furthermore, room-temperature ductility may also be increased by changing the shape of a brittle dispersed phase from platelike to equiaxed or spheroidal.8 Overaging and redissolving of the secondary phase limit the maximum temperature to which precipitation-hardened alloys can be used. However, in a binary eutectic system, both phases coexist up to the melting point. Although all eutectic structures are not completely stable,21 a dispersion-hardened cast high-temperature alloy might result if a fine distribution of one of the eutectic phases could be obtained during solidification. An additional reason for interest in eutectic alloys is their excellent castability.22 Since eutectic alloys, like pure metals, freeze at a single temperature rather than over a range of temperatures, their castability is superior to solid-solution alloys with long liquidus to solidus ranges. The purpose of this research was to study the effects of small solute additions on the microstructure and mechanical properties of a number of high-melting-point eutectic compositions.

Jan 1, 1967