Search Documents

By Oliver Bowles

"INTRODUCTION Slate has earned a high reputation as a roofing material, carefully selected and properly placed it is rainproof, attractive, and extraordinarily durable. Despite there qualities in its favor, the slate industry during the past 30 years has suffered marked reduction in volume of sales. An increase in building construction and general improvement in business will doubtless bring renewed activity, but considerable ground has to be recovered before the industry can become prosperous. Influences tending to dwarf this long-established industry producing materials of world-wide reputation are analyzed briefly in the following pages in the hope that they may be rectified.HISTORY OF SLATE PRODUCTIONFigure 1 shows graphically the rise and fall from year to year of sales of roofing slate since 1885. In quantity, the peak was reached in 1902, and the most serious decline was from 1912 to 1918, sales at the end of this 6-year period being only one third those at the beginning. Unlike most building materials, slate experienced only a slight recovery in volume of sales during the post-war period, 1920-29. The value closely parallels the volume up to the World War period. Subsequently, however, as unit values increased the aggregate value rose sharololy above the volume curve, attaining in 1928 the point reached in 1903, although the Lumber of squares sold was scarcely one third as great. The increased unit value was due partly to larger sales of heavy architectural grades."

Nov 1, 1933

By F. D. Wright, H. D. Fara

The solution to the plastic and elastic stresses around a circular shaft in a hydrostatic stress field that has appeared in two editions of a widely used book on rock mechanics1 is in error. Although this is a relatively minor matter, the correct solution was not found by a literature survey, so it appears worthwhile to present it. For a homogeneous, isotropic, rigid plastic-elastic body in plane strain which obeys Tresca's yield criterion the following equations must be satisfied:'," In the plastic zone,

Jan 1, 1963

By John C. Holtz

Interest in the possibility of using Diesel6/ engines for haulage power in mining and tunneling is increasing in the United States, owning largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requests for information as to the factors that must be considered if Diesel engines are to be used safely underground.

Jan 1, 1940

By Woodcock J. T, Sparrow G. J, MacRae C. M

The external urfaces and interiors (as polished sections) of particles of coconut hell and extruded peat activated carbons taken from everal Australian carbon-in-pulp operations were examined with an optical micro cope, a scanning electron microscope, and an electron microprobe.Calcium carbonate (calcite) precipitated from the pulp was the major inorganic material on the external surfaces of the carbon particle, but several ore minerals, including quartz, hematite, pyrite, arsenopyrite, and clay minerals were also identified, along with trona, gypsum, a nickel cyanide, and a magnesium salt. Sections of carbon particles showed that calcite was virtually the only introduced inorganic material inside the carbons.It was distributed in the pores and cracks throughout the coconut shell carbon particles but tended to be concentrated in the outer layers of the extruded peat carbon particles. The mechanism of calcite formation and deposition is uncertain. Gold X-ray dot maps showed that gold was distributed through to the centre of coconut shell carbons and to a depth of at least 500 µm in extruded peat carbons. The distribution of gold within the carbon particles was similar to that of calcite.

Jan 1, 1988

By L. R. Nelson

A review is presented of the furnace cooling system design and operating developments since the initial furnace start-up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators, in particular, to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement of operating this slag in a relatively highly superheated state (?T ?400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomization. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to HATCH high-intensity, water-cooled, copper Waffle coolers and tap blocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area), coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the HATCH Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By S M. Zhang, Y X. Han, J Liu, Y J. Li

"Compared with conventional roasting and magnetic separation processes, higher reduction temperatures and stronger reducing atmospheres are used in reduction technologies to reduce iron oxides to metallic iron, which is often liberated during reduction and amenable to magnetic separation. Reduction and magnetic separation of an Australian refractory iron ore was therefore studied as a function of reduction temperature, time and coal addition. It was found that during reduction, the particle size of the reduced iron increased with reduction temperature and time. Subsequent magnetic separation tests were further conducted on the reduction products. A reduced iron powder with a Fe grade of 85.67 per cent was obtained at a Fe recovery of 87.82 per cent under optimum reduction conditions where a metallisation rate of 85.82 per cent was achieved. The mechanism involved in reduction is discussed based on XRD and SEM examinations.CITATION:Han, Y X, Liu, J, Li, Y J and Zhang, S M, 2013. Upgrading an Australian iron ore by reduction and efficient magnetic separation, in Proceedings Iron Ore 2013, pp 397-402 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Walter R. Storms

"INTRODUCTION The New Mexico potash exploration described herein was begun in February 1944 with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the Reserve and in the immediate vicinity.The Potash Reserve is in secs. 26; 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of Carlsbad, as shown on figures 1 and 1A, Drilling was done in secs. 26 and 35 of the Reserve, in section 14 to the north, end sections 2 and 56 to the east. All work was done on Governnent-owned, unleased land.The Reserve may be reached from Carlsbad by traveling to the north-east by automobile for about 14 miles on the paved U. S. highway 62. This highway passes through the southern part of the Reserve. Other parts may be reached by a State highway that passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Santa Fe Railroad also passes across the southern part of the Reserve enroute from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the project and 22 miles from Carlsbad."

Aug 1, 1947

By Jochen Petersen, Harro von Blottnitz

"The landfill disposal of slags is common practice in the metallurgical industry. Chromium may be a minor constituent in many cases. It is present mostly in the form of chromites, which are considered environmentally benign and hence safe for disposal. Wastewaters from metal finishing operations are most commonly treated by reduction and precipitation of dissolved metals, including chromium, by lime addition, and subsequent landfill disposal of the resulting sludge. The metals contained in such sludges are mostly in the form of hydroxides, and as such considered environmentally stable.Thermodynamically, trivalent chromium, which is the predominant form in these waste materials, can be oxidised to the hexavalent form by atmospheric oxygen. Detailed research work on both slags and sludges has shown that a gradual emergence of hexavalent chromium can indeed be observed. The mechanism is governed by close physical contact between chromium oxide (or hydroxide) phases on the one side and calcium oxide (or hydroxide), which is present as flux in slags and residual lime in sludges, on the other. If oxygen can migrate to the points of contact, gradual formation of calcium chromate ensues.Hexavalent chromium is associated with high environmental toxicity, and hence undesirable in landfilled materials. Moisture migrating through landfill deposits can mobilise the highly soluble chromates and thus potentially transport them into natural waterways. Such gradual release from stainless steel and ferrochromium slag deposits has been demonstrated in a column experiment."

Jan 1, 2003

By John C. Holtz

Interest in the possibility of using Diesel6/ engines for haulage power in mining and tunneling is increasing in the United States, owing largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requsts for information as to the factors that must be considered if Diesel engines are to be used safely underground.

Jan 1, 1940

By J. Mitchell Linne

In 1985, at the request of Bureau of Land Management, the U.S. Bureau of Mines studied a 54,480-acre portion of the 93,205-acre Dry Valley Rim Wilderness Study Area (CA-020-615), in order to evaluate its identified resources. The area studied is in Washoe County, NV, and Lassen County, CA, about 35 miles east of Susanville, CA. No metallic resources were identified. The Red Rock and Willow Springs areas contain 85 million tons of altered basalt with zeolite amygdules. This material, averaging more than 50 percent chabazite, constitutes a subeconomic zeolite resource. This zeolite-bearing material would require beneficiation to upgrade it for higher value uses. Natural zeolites have a small market in the United States, which is presently supplied by other higher grade material. There is low probability that these resources will be mined in the foreseeable future. The Capricorn claims, adjacent to the study area, are on alluvial sediments containing more than 30 percent montmorillonoid clays. The material is not usable as pozzolan and was not tested for other uses such as absorbency, oil clarification, or insecticide carrier. The term pozzolan refers to a number of siliceous materials which are combined with portland cement to enhance the physical properties of the resultant concrete. The area is remote from market and contains low value material. It is improbable that this occurrence will be mined in the foreseeable future.

Jan 1, 1987

By H. D. Kline

This paper is one of a series being prepared by the Bureau of Mines on methods, practices, and costs in various mining districts in the United States. The paper describes mining and ore recovery methods common to the Batesville manganese district, Independence County, Ark., and gives the costs of producing merchantable ore by three operators whose methods were more or less typical of those of many other local manganese producers. The operating costs reported were those of Leonard Baxter at mines on Brooks Hill for the calendar year 1958 and Arkansas Mining and Exploration Corp. at Section 16 mine and the Searcy group of mines and Miller-McGee Corp. at the Diener mine during the first 6 months of 1959. Manganese are was mined in the district as early as 1849 and almost continuously thereafter until August 1959, when termination of the Government's domestic manganese purchase program resulted in complete cessation of mining activity. During those years, production came from more than 189 mines and properties, of which only a few produced as much as 30,000 tons of merchantable ore.

Jan 1, 1962

By H. Yavuz

Physical modelling is one of the research tools in the understanding of the failure mechanisms and the deformations likely to be experienced by the strata during mining operations. Success of the physical models to predict the strata behaviour depends on satisfaction of the scaling requirements in modelling material used. This paper gives results from a laboratory work carried out into the factors influencing the strength and elastic properties of a physical model material to satisfy the scaling requirements determined from application of dimensional analysis to the pertinent variables affecting the deformation and failure of the underground structures. It was found that the conditions for preparing the material over its composition had a great influence on the final properties. The effect of different water quantities, sand size and mixing time upon the properties of modelling material was studied and water requirement for different proportions of sand/plaster to prepare the material was optimized. Various sand/plaster ratios of compositions were cured at three different levels of oven temperatures. Curing at low temperature produced material within the average modulus ratios ranging from 290 to 432, which are common to most rock types according to Deere?s rock classification, whilst curing at high temperature produced material within the low modulus ratios ranging from 64 to 140 depending on its composition. A combination of low and high temperature curing resulted with an increase in modulus ratio compared to high temperature curing. Curing the material at low temperature compared to other curing temperatures provided a satisfactory range of strength ratio. It has been shown that the relative amount of filler to plaster in the mix controls the frictional properties of the material and results with an increase in strength and modulus ratio of the material provided that suggested preparation and curing conditions were applied. Model material developed by curing at low temperature simulated modulus ranging from 241 to 343 and strength ratios ranging from 11.6 to14.8 of a coal mine rocks, satisfactorily.

Jan 1, 2003

By Lise Chénard

El presente texto señala los lineamientos del proyecto REFORMIN, así como su repercusión en la dinámica de promoción de la industria minera. REFORMIN surge en el 2001 como un proyecto bilateral entre Canadá y Bolivia, cuyo financiamiento proviene de la Agencia Canadiense de Desarrollo Internacional (ACDI). Su finalidad es apoyar al Viceministerio de Minas, facilitándole el acceso a la pericia canadiense para lograr una gestión más sana y eficaz de los recursos minerales del país. Para ello, se basa en los principios fundamentales tales como: mejora de la gestión del medioambiente minero, apoyo a la prevención y gestión de conflictos sociales en las comunidades mineras, a los mineros artesanales y a la promoción de los recursos minerales del país, -en tanto benefician al desarrollo de la industria minera en un contexto de mercado globalizado.

Apr 22, 2003

By John E. Newby

The Brightwater Conveyance System consists of four tunnel segments in three tunnel con-tracts, comprising over 21,760 m (71,400 ft) of pressurized face tunneling in complex glacial and non-glacial soft ground conditions with a large proportion 60 m (197 ft) or more below the ground surface with up to 7 bars groundwater head. This resulted in unique technical challenges for establishing geotechnical baseline values. The process used to develop these baseline values and specifications with regard to the level of risk that the owner, King County, was willing to accept is described in this paper.

Jan 1, 2008

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By L. J. Barnes

The process for bio-remediation of sulphidic slag (BROSS) operates at 45 degrees C in a neutral (pH 7), aerobic aqueous environment in which sulphide in the slag is converted to sulphate. A two-stage version has been developed that involves quantitative chemical pre-oxidation of total sulphide to thiosulphate, followed by complete biooxidation of thiosulphate to sulphate. Ferric hydroxide, also produced, acts as a flocculant in the bioreactor effluent, concentrating heavy metal precipitates in the thickener as a sludge which can be returned to the smelter. The process has a high sulphate production rate and low acid and nutrient consumptions. Microorganism growth is the rate-limiting stage, requiring a minimum liquid residence time in the bioreactor of about 7 h. Although large quantities of oxygen are needed, sufficient gas mass transfer can be attained in an air-lift reactor. Products are an aqueous stream containing sodium sulphate with only trace levels of toxic heavy metals and a benign, toxic metal-containing sludge

Jun 18, 1905

By Thomas Curtin

The Bureau of Mines, in its researches aimed to prevent wastes and to increase efficiency in oil-well practice, has investigated the matter of casing troubles and fishing methods. The results of the investigation are set forth in this paper. After expensive development work, many wells being drilled for oil have been abandoned because of casing troubles. These troubles in many instances have been thought to be insurmountable, whereas they are sometimes susceptible of solution. In fields_ where casing difficulties are of daily occurrence, methods have been evolved for combating them. Were these methods more widely known and applied wherever the same conditions exist, the oil industry at large would be greatly benefited. This report attempts to classify these troubles and suggests solutions that will save the operator discouragement and expense. It is assumed throughout this paper that the reader is so familiar with the ordinary oil-well drilling and fishing methods that detailed explanation is unnecessary. The well-drilling terms that are used herein will be readily understood by those for whom this discussion is intended. However, in order to avoid confusion as to the sense in which some of these terms are applied, definitions &re included.

Jan 1, 1920

By S. J. Frank

The development of feedforward semi-empirical control models for furnaces and the evaluation of mass balances are based on plant data. The models can only be as good as the data and it is therefore required to know the inherent uncertainty associated with the plant data. This uncertainty stems mainly from the fact that the slag, alloy or dust, have a distributed nature that depends on the degree of mixedness. It is commonly accepted that melts from open bath furnaces are well-mixed, and submerged arc furnaces less so. The impact of this assumption is significant, as a reasonably homogeneous melt could be represented by one sample only. As so much of metallurgical control depends on the assay information of the alloy and slag melts from furnaces, it was decided to characterise the possible variation in melt chemistry and temperature. Sampling campaigns and continuous temperature measurement of the melts were performed for different alloy and slag taps at a major ferrochrome producer. Both a submerged arc furnace and open arc furnace are evaluated in this way, by way of comparison. The slags of both open arc and submerged arc furnaces were found to be of similar degrees of homogeneity, with much spatial variance in the reducible iron and chromium oxides. However, it was found that the alloy melts deriving from open arc furnaces were significantly less homogeneous than the alloy derived from submerged arc furnace alloy production. The compositional variance could be related to the furnace operating conditions and it affects both metallurgical accounting and process control. In all cases it was found that the variance in melt solute components are larger than can be ascribed to analysis instrument error. It will be shown how this predetermined variance in melt composition could be included in process modelling and control.

Jan 1, 2004

By William G. Pariseau

The research reported here concerns a four year study of the rock mechanics aspects of two underground hardrock mine study stopes. The first study was conducted at Anaconda Minerals Company's Carr Fork Mine near Tooele, Utah. The second study was conducted at the Homestake Mining Company's Homestake Mine In Lead, South Dakota. Both case studies were cooperative efforts of mining company personnel, the Spokane Research Center of the Bureau of Mines and the Department of Mining Engineering, University of Utah. Large diameter (6 1/2 In.) blastholes were an integral part of the stoplng method at each mine. A true vertical crater retreat (VCR) method was used at the Homestake Mine, while a vertical bench mining method (VBM) was used at the Carr Fork Mine. VCR and VBM methods were developed In the 1970's; they offer significant productivity gain and are now used throughout the world. The new technology, however, brings with It a requirement for more sophisticated engineering design and control. Since there are no personnel in a VCR or VBM stope, all ground control Including dimensioning of stopes and pillars and the layout of cable bolt assays or other artificial support must be done in advance of production blasting. Accordingly, the objective of the research study was the establishment of a procedure for optimizing stops and pillar sizes. The approach taken was In each case a combination of mine measurements of the study stope response to mining, laboratory testing for rock properties and In situ stress measurements of the premining stress field, and theoretical calculations of the study stope response to mining. All calculations were done with the UTAH-II finite element computer program. Simulation of the blasting sequence gave a correlation of 0.88 between measured and calculated extensometer readings (Incremental relative displacements) at the Carr Fork Mine where other 30 Instrumentation boreholes were used to monitor the test stope response. A correlation of 0.84 was obtained at the Homestake Mine where 19 instrumented boreholes were used for monitoring purposes. These high correlations validated the computer mode and calibrated It for rock mass properties. The calibrated model was then used In parametric studies of alternative design layouts.

Jan 1, 1985

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971