Search Documents

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

By Nuno Cruz

"The concrete overbreak estimation for bored piles provides the quantification of the shaft’s expansion beyond its theoretical volume. There are stability analysis methods that can be employed before and after concrete pour but as for the moment of decision, during pile cast, the most common method still consists in measuring the rising of the concrete level in order to compare its poured volume with the theoretical pile section volume. This is a determinant parameter to monitor, not only because it assesses the bored shaft stability but also because it represents a direct cost. When analyzing the estimation methods commonly applied on-site it becomes evident that these are often affected by human errors that lead to misleading results. The objective of this paper is to identify those errors and discuss a subject which is usually overlooked. As a general conclusion, it was ascertained that most errors derive from inaccurate volumetric data, working procedures and gauging equipment. By acknowledging these widespread practices deep foundations contractors will be in a better position to make informed decisions on how to correct and improve bored pile stability.GENERALBackgroundWhen executing bored piles, the estimation of its concrete overbreak allows a swift appraisal of the excavation stability during the drilling process. This is simply obtained from the proportion of the poured volume of concrete over the drilled shaft theoretical volume, as shown in equation [1].Where CO = concrete overbreak percentage, Vc = volume of poured concrete, Vr = pile’s theoretical volume. This calculation not only provides a general idea of the shaft’s expansion from its theoretical volume, but also the outline of the excavated column’s geometry. For the latter, the outline will be as accurate as the number of measurements taken for each partial known volume of poured concrete. This means that for each load placed inside the excavation there is a corresponding rising of the concrete level. The profile of the definite pile is then plotted (see Fig. 1) and allows inferring about how stable remained the shaft walls up to the moment of casting.The technological developments in this area have provided other methods for determining pile stability before and after pile cast, such as ultrasonic echo sensing, cross-hole sonic logging or thermal integrity profiling systems. Notwithstanding, concrete overbreak assessment remains as common practice and confers the advantage of providing stability information during the process of pile casting."

Jan 1, 2017

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By Steve Dubnewych

The Joint Water Pollution Control Plant, operated by the Sanitation Districts of Los Angeles County, treats wastewater generated by over three million people. A new tunnel and ocean outfall is being considered to meet future hydraulic demands and provide long-term redundancy for the Districts? existing tunnels, portions of which were constructed as early as the 1930s. The detailed process used to evaluate the feasibility of various tunnel and out-fall locations is described. Challenges include a geologic profile with mixed face and squeezing ground conditions; high water pressures; active fault crossings; gassy and contaminated ground conditions; and liquefaction, slope stability, and lateral spreading concerns in the area of the riser and diffusers.

By P. B. Altringer

The Federal Bureau of Mines conducted a study to determine if residues from fractional distillation represent a potential source of mineral values. A literature review and discussions with tar sand specialists failed to disclose the mineralogical nature of residues remaining after bitumen extraction. To develop this information, pilot plant tar sand residues or toluene-cleaned tar sands from 23 deposits were examined. The nature of the residues was determined by standard mineralogical methods and the chemical compositions were determined by X-ray and ICP (inductively-coupled plasma spectroscopy). None of the sands or concentrates examined contained sufficient valuable minerals to be economically important.

Jan 1, 1982

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By A. H. G. Mitchell

Most, if not all, of the six recognised post-Cretaceous, predominantly andesitic mineralised belts in the region are now thought to be subduction-related magmatic arcs. The Inner Carpathian arc and the Eastern Bosnia or Drina-Rhodope arc host numerous vein and replacement deposits with epithermal features and Zn-Pb+/-Ag as the predominant economic minerals. In contrast, the south Apuseni Mountains have produced over 1 600 t Au from epithermal veins but very little Zn-Pb. Recent age determinations and geophysical data from the Baia Mare district of the Inner Carpathians suggest that mineralisation succeeded volcanism by 1-2 m.y. and accompanied crustal extension and the cooling of a large, mushroom-shaped pluton whose boundaries define the mineral district. In the south Apuseni district, mineralisation can be explained by mixing of meteoric with low-salinity metamorphic water expelled during intrusion of mafic rocks into the middle or lower crust. The more continental or cratonic crust in the Drina-Rhodope and Inner Carpathian arcs precluded the input of low-salinity, Au-bearing metamorphic water; the Zn-Pb deposits formed where convecting meteoric water mixed with saline water, possibly introduced through carbonate rocks in the basement

Aug 1, 1996

By S. J. Rodgers

This report presents guidelines on methods of dust control in conventional coal mining operations. The normal mining cycle and equipment used in a room and pillar conventional section are described. Main ventilation, section ventilation and face ventilation are discussed in detail. Proper installation of line brattice, maintenance of proper air flows at the face and split ventilation are stressed. The effects of maintaining the end of the line brattice near the face are described. The advantages and disadvantages of blowing and exhausting face ventilation are presented. The use of water sprays on cutter bars and loading machines is described. The design of a nonclogging water spray system developed under a Bureau of Mines contract is presented. Other methods of reducing dust exposure are discussed and include alternative procedures for shot firing and administrative controls.

Jan 1, 1983

By George A. Morgan

The 53 countries that constituted Africa in 1990 accounted for a significant portion of total world output of a number of mineral commodities. Among the most significant to be produced in Africa were andalusite, antimony, asbestos, bauxite, chromite, coal, cobalt, copper, diamond, fluorspar, gold, lithium minerals, manganese, phosphate, platinum-group metals, the titanium minerals-ilmenite and rutile, vanadium, vermiculite, uranium, and zircon. Several of these, chromite, cobalt, diamond, and manganese, were not produced in the United States. Despite the underdevelopment of much of Africa, mineral raw materials playa very important part in the national economies of many of its countries. In many cases, the production of minerals is the dominant economic activity in the country, often having the largest and most sophisticated work force. In several countries, one or two mineral commodities are dominant in a weakly diversified economy. Among these are petroleum and diamonds in Angola, petroleum in the Congo, gold in Ghana, bauxite in Guinea, uranium in Niger, phosphate in Senegal and Togo, and copper and cobalt in Zaire and Zambia.

Jan 1, 1992

By O. H. Metzger

This is one of a series of papers on placer mining in the western United States. The author has endeavored to give a general outline of the available placer deposits in Boise County, Idaho, together with a description of current practices and the recovery costs of the principal producers. The paper is based on a field examination by the author in May and June 1937. Boise County (fig. 1) is in the southwestern part of Idaho. It has a maximum length of 60 miles, a maximum width of 42 miles, and an area of approximately 1,600 square miles.

Jan 1, 1938

By Carlos A. Prato, Federico Pinto

"ABSTRACTThe design of drilled shafts often incorporates large factors of safety, for which settlements under service loads are highly influenced by the initial elastic stiffness. In the case of groups of drilled shafts with typical spacing, the elastic shaft-soil-shaft interaction dominates the behavior even for loads close to the bearing capacity, for which the initial stiffness is a key parameter in the design. This paper describes typical trends in results obtained by means of different approaches currently available in the literature for the evaluation of the initial stiffness of a single shaft. An experimental technique that provides a rapid and inexpensive means for the evaluation of the initial stiffness is described, and the results obtained for typical cases are compared with analytical predictions.IntroductionThe behavior of drilled shafts under axial loads is generally governed by the initial stiffness, as the factors of safety considered in design are often large, due to a superposition of conservative assumptions on soil properties and expected loads. In the case of shaft groups, the initial elastic stiffness plays a major role together with the elastic group effects, as nonlinearities tend to localize around the shafts and have a lesser effect than elastic deformations on adjacent elements (e.g., Leung et al., 2010). An accurate characterization of the initial stiffness is thus warranted for the analysis of drilled shafts and shaft groups under service loads.Initial stiffness of shafts may be estimated on the basis of soil stiffness and structural properties of the element by means of numerical methods (e.g., Pinto and Prato, 2006), as well as analytical methods (e.g., Randolph and Wroth, 1978). The soil stiffness may be determined by means of geophysical tests (e.g., Spectral Analysis of Surface Waves, SASW, Stokoe et al., 1994), or correlations with Standar Penetration Test (SPT) blowcounts or Cone Penetration Test (CPT) resistances (e.g., Sabatini et al., 2002).The initial stiffness may also be measured on drilled shafts by means of load tests. Static load tests (SLT), however, have some limitations on measuring small deflections, for which the initial stiffness is often extrapolated by means of large strain measurements (e.g., Chin, 1970), where the SLT measurements are more accurate."

Jan 1, 2014

By D Craw, C E. Martin, C Smith, C Rufaut

Wangaloa Coal Mine opened in 1945, and by the time of its closure in 1989, had produced 750 000 tonnes of coal and disturbed an area of 75 ha. The original mining licence required land rehabilitation to exotic forestry, however the current owner, Solid Energy, has worked with Crown Minerals and local councils to write a new rehabilitation objective. The site is now being stabilised and replanted with native species, and may be available for public use before the coal mining licence expires in 2007. Site discharge permits expire in 2017, and by that time, it is anticipated that discharge water chemistry will be similar to background levels. MWH are currently contracted for management of the mine rehabilitation project. The Kaitangata coal unit mined at Wangaloa is sulfurous lignite with associated pyrite. Kaitangata coal contains 3.2 wt per cent sulfur, which is higher than most New Zealand coals. Initial analyses at Wangaloa indicate low pH (2.56.2) values in soil, groundwater and surface waters as a result of acid rock drainage (ARD) processes, leading to increased metal mobility and challenging conditions for vegetation. Pilot studies indicate pinus radiata needles contain up to 67 mg/kg boron, and elevated As, Cu and Zn concentrations in surface waters. The main lake at the site has a pH of approximately 4.9, despite lime dosage in 2002. There is a real need for a complete geochemical model of the Wangaloa coal mine. Such a model could be applied to similar restoration projects, and would assist by pinpointing geochemical processes and toxic metal relationships most harmful to the receiving environments. Using this model, rehabilitation in the future will be targeted and more efficient. This project is part of a larger scheme to characterise and model the Wangaloa mine site restoration, including waters, soil, vegetation, geology and invertebrates.

Jan 1, 2003

The visit which took place on the 18th February, 1972 was a departure in that the places visited had no direct connection with the work in which members of the Institute are normally engaged. It was refreshing and stimulating to see important and involved operations normally outside ones own trend of life and to have experts to speak about technical, financial and matters of general interest concerning their work, not forgetting their troubles and problems and how they overcame them. Carlton Centre The members of the Institute were received by Mr D. Appleton, Public Relations Officer of the Carlton Centre Limited, who introduced Mr L. R. M. Fee of W. Rhodes Harrison, Architect in charge of the project; Mr W. C. E. Skilton of Murray and Roberts, the Engineer in charge of the construction of the complex and Mr A. Home the Senior Operating Engineer of Carlton Centre Limited. Each of these gentlemen addressed the members giving short rundowns on the project with special reference to their particular sphere of the undertaking. A variety of particularly interesting statistics relating to the planning construction and the ultimate operation and maintenance of the complex was given. Mining engineers present had an opportunity to compare the problems encountered by them associated with depth to problems encountered by the civil engineer in the construction of a building rising to such an enormous height. To some of the members a sense of similarity of the labour problems encountered must have been recognised. After tea the visitors were divided into groups, each under the guidance of an official, and then visited the highest floor accessible and thereafter the 19th floor where the internal arrangements for airconditioning, lighting, plumbing, power supply and communication arrangements were explained. Thereafter a visit to one of the seven basements which houses all machinery required to serve this enormous complex enabled the visitors to see the standby power arrangements as well as the refrigeration plant. The visit finished in time to proceed to the Crest Hotel in Hillbrow for lunch. To our hosts for the visit to the Carlton Complex a special vote of thanks is recorded. Strydom Tower In the afternoon the party proceeded to the Strydom Tower where Mr Knight from the Public Works Department who was the Engineer in charge of the construction of the tower gave details on the construction and the extraordinary methods which had to be adopted to achieve the desired objectives and to overcome known as well as unforeseen difficulties. The comparatively short time taken to complete the project and the good safety record appeared to impress the visitors. The final phase of the visit was taken care of by Mr Bothma of Telecommunications Department of the Post Office, who gave an extremely interesting explanation of the telecommunication organization of the Post Office with particular reference to the part the Hillbrow Tower plays in the South African telecommunication system. Both gentlemen answered many questions willingly and interestingly. Following the explanatory talks the visitors were shown the technical equipment housed in the two top levels of the tower. Short explanatory talks gave members an insight into the workings of one of the most important aspects of modern life. Even to the amateur photographer opportunities existed to view and photograph the city from the highest available observation point. We are indebted to Mr Gouws, the Regional Director of the Post Office for granting permission to visit sections of the tower normally not accessible to the general public and to our hosts for the manner in which we were received and entertained on the explanation of the many interesting features of this important installation. In conclusion, the programme for the day can be classified as interesting, of exceptional educational value, and an opportunity to see something of the engineering skills put into two vast and ambitious undertakings and the results achieved.

By Edward M. Dowey

The concrete lining for a long 8.05 km (5 mi) section of New York City Water Tunnel No. 3 was cast in place. The contractor, Grow-Perini-Skanska, placed over76,841 m3 (100,505 cy) of concrete, pouring 24 hours per day, 5 days per week. The concrete was dropped 204 m (670 ft) to the tunnel level, transported by rail to a concrete remixer and pump, and placed in 146.3m (480 ft) of full circle forms. Some of the many challenges include the sheer magnitude of the job, navigating through drifts, a raise and curves, dealing with ground water inflows, and placing the concrete within time limits.

Jan 1, 2001

By Edward J. Cording, William H. Hansmire

INTRODUCTION The Washington Metro, a rapid transit system that will serve the District of Columbia, Virginia, and Maryland, has been under construction for about two years. Construction of the Metro by the Washington Metropolitan Area Transit Authority involves a large amount of cut and cover, soil tunnel, and rock tunnel construction. To aid initial construction and improve future designs, performance observations were undertaken on tunnels in the initial construction phase. The University of Illinois Department of Civil Engineering was engaged to carry out a comprehensive program of field observations and measurements for this purpose. One part of the program was on the first soft ground tunnel constructed in the system. The tunnel is a 2200-ft (670 m) twin-bore section, designated Contract A-2, in downtown Washington. Two objectives of this program were to determine the relationship of construction procedure to settlements and to observe the pattern of soil movement around the tunnel as an aid in evaluating underpinning criteria for nearby structures. A test section, consisting t three instrument lines located across the tunnel path, was established prior to mining in Lafayette Park to measure in detail both vertical and lateral soil displacements as the tunnel was mined through the section. The site was selected because it is free from surface structures and access for installation and reading of the instruments was convenient. Load and distortion measurements on the lining were also made within the test section; observations of construction procedure were maintained throughout construction.

Jan 1, 1997

By Ren G. Dong, Jay Kim, Daniel E. Welcome, Won Joon Song, Charles Hayden

Prolonged, extensive exposure to hand-transmitted vibration could cause a series of vibration-induced disorders in the vascular, sensorineural, and musculoskeletal structures of the human hand-arm system, which have been collectively called hand-arm vibration syndrome (HAVS).1 To assess the risk of HAVS the international standard ISO 5349-1 (2001)1 recommends using the root-mean-square (rms) acceleration of the measured vibration with a frequency weighting. While a few epidemiological studies have reported results consistent with the predictions made according to the recommendation, many other studies have reported results with large discrepancies.2 This may be partially attributed to the time-averaging effect involved in calculation of the frequency components, especially for impact type tools. Because the spectral characteristics of impact tools change dramatically with time, a time-frequency (T-F) analysis can provide better characterizations of such highly transient vibrations. The analytic wavelet transform (AWT) is an ideal T-F analysis tool because it possesses the advantages of both the Fourier transform and the wavelet transform.3 The objective of this study was to explore the application of the AWT method for characterizing the impact tool vibrations and assessing their exposure risk. Methods Five tools (two chipping hammers, two riveting hammers, and one concrete cutting saw) were used in this study. The saw vibration was measured when it was used to cut a section of road pavement during a repair. The vibrations on the other tools were measured by the procedure specified in ISO 8662-2 (1992).4 A sampling rate of 16,386 Hz was used in the measurement. The AWT and Fourier analysis were applied to these signals and to identify their characteristics. Results Figure 1 compares the T-F characteristics of the accelerations measured from the relatively steady concrete saw and a riveting hammer. The frequency weighting specified in ISO 5349-11 was applied in the calculations. The comparison clearly shows that the two tools have completely different T-F characteristics.

Jan 6, 2006

Of late there have been various papers published on this subject by various authorities, in which certain definite factors influencing slime settlement have been brought forward. As the principles set forth by these writers are of great interest, and have, in most cases, been generally accepted, the author will review them in the hope that by discussion some more knowledge may be brought to bear on many points connected with the subject.The definition of slime at the present time is not a standard one, and varies according to different authorities, some defining slime as ore crushed to such a fineness that it will pass through a screen of standard size, say 150 or 200-mesh, in water (1, 2);others as that part of the finely-crushed material which is in the physical condition which causes it to remain in. suspension in water, and possesses pr?perties which render it almost unleachable (3). Authorities seem divided on this point, but of late American writers seem to prefer the former definition. On the contrary, B L Gardiner describes slime as a mixture of small particles of crushed ore of varying sizes which, when mixed with water, tend...

Jan 1, 1912

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSWA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. metallic mining workforce from March through September 1986. Similar reports have been published for the stone, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988