Search Documents

By Gary E. Sherman

This report presents a Bureau of Mines study on the cost of mine permitting and compliance with environmental regulations in Alaska. It discusses permitting requirements and procedures for placer and lode mines. Placer miners must comply with recently established (1988) water quality regulations and effluent treatment requirements. To estimate the impact differing treatment options (no recycle, 100% recycling, and flocculation) have on a placer mine's rate of return, three models (1,500, 1,000, and 500 yd3/d) were simulated. Rates of return for these models show a marked decrease as effluent treatment is increased. The incremental increase in operating cost from one treatment option to the next is relatively small; however the opportunity cost of lost production if' significant and accounts for the decreasing rate of return with increased effluent treatment. Lode mines face greater costs for permitting and compliance than similarly sized placer mines as a result of the impact of the operation. Direct permitting costs for lode mines range from 2 to 6% of total project cost, with 4% the most common figure cited by industry. Total costs for permitting and compliance are approximately double those for permitting. Indirect costs associated with compliance include mitigation, monitoring, and reclamation.

Jan 1, 1991

By Valentin Choquenaha Bombilla, Oscar Alvarez Muiloz

"Tintaya’s basic production line is copper concentrate, which has an important gold content. The process used is flotation; the objective of the metallurgical department is to obtain the best results in the copper recovery without neglecting the gold, using very specific reagents. Copper recoveries are considered high, nevertheless every day emphasis is placed upon increasing those recoveries. Regarding gold, optimum recoveries could not be achieved with flotation; and implementation of a gravity circuit was considered.According to microscopy studies, the coarse and very fine grains of gold in native form are lost to tails. The native gold due to its high specific gravity is concentrated at the underflow of the cyclone, remaining in the circulating load of the circuit. It reaches three times the concentration compared to the head grade entering the ball mills. This re-circulation generates very fine and laminated gold particles inside the ball mill, passing to the classification stage making a short circuit to the overflow of the cyclone.The very coarse gold particles as well as the thick flakes of gold do not react favorably to the conventional flotation process; thus studies that have included gravity separation have been conducted to increase the gold recovery. Part of the research included concentrating tables, jigs, and Knelson Concentrators. The Knelson Concentrator proved to be the best selection in terms of metallurgical performance and recoveries considering the throughput and operation conditions of the Tintaya Plant.The gravity concentration circuit with the Knelson Concentrator was commissioned in BHP Tintaya in October 1998, as per the flowsheet shown later on. Presently the global gold production surpasses any estimated expectations.Present efforts are directed towards showing the evaluation and optimization of the different parameters that govern the performance of the Knelson concentrator, as well as illustrating the difficulties and successes throughout the operating period.In the first year of operation 200 tons of gold concentrate have been produced with an average concentrate grade of 320 gramdton, having paid back in full the cost of the automated KC-XD- 48 Knelson Concentrator, the peripheral equipment, and the cost of the installation."

Jan 1, 2002

By Zsuzsanna Zborovszky

Study of different parameters (minimum discharge voltage, minimum discharge current, wire electrode diameter, speed of separation, electrode materials, overlap of the electrodes, etc.), their direct effect on the power going into the discharge, and their indirect effect on the possibility of obtaining ignition with an 8.31% methane-air mixture from a resistive circuit. Critical evaluation of the Cadmium disc breakflash (the presently internationally recommended test apparatus). Description of experimental setup and apparatus.

Jan 1, 1974

By William A. Beck

The Construction Aggregates Corp. operates a plant for processing sand and gravel from two deposits in Ottawa County, Mich. The bulk of the sand is obtained from a sand dune on the shore of Lake Michigan, and the gravel is dug from a glacial-drift deposit farther inland. Mining is done with draglines, and the material, both at the digging site and in the plant, is moved mainly by systems of conveyors. The Ferrysburg plant serves customers along the Great Lakes, which is unusual for a business normally local in character. Annual production exceeds 1-1/2 million tons of sand and gravel as concrete aggregate and 200,000 tons of core sand for foundry use.

Jan 1, 1962

By Qingzhu Li

The brewing industry byproduct, spent grain (SG), was evaluated for its ability to adsorb Ag(I) from aqueous solutions. Ag(I) adsorption was dependent on solution pH, contact time, adsorbent dose, initial Ag(I) concentration and temperature. The kinetic data were well described by pseudo-second-order kinetic model, indicating that chemical adsorption was the rate-controlling step. The equilibrium data followed Freundlich isotherm rather than Langmuir isotherm, suggesting heterogenity of the adsorption sites on spent grain. Ag(I) desorbed from Ag(I)-loaded spent grain was also evaluated in this study. HCl, NaOH, Na2S2O3 and ultrapure water were chosen as eluants and desorbed Ag(I)-loaded spent grain for 30min, Ag(I)-loaded spent grain desorbed in 0.1M Na2S2O3 exhibited higher elution efficiency as compared with other eluants. The results indicated that application of spent grain for adsorption and recovery of silver from aqueous solutions was feasible.

Jan 1, 2009

By Andre Zingano

The objective of this paper is to study the effect of annulus thickness on the quality of resin mixture for fully grouted resin bolt. Pullout and mixture tests were made in underground coal mines for the following arrangements: (a) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with steel wire around the roof bolt; (b) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt; and (c) borehole diameter 0.95 in. (24 mm) and a roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt. The mixture test in steel pipe showed that the best resin mixture is for borehole with 0.95 in. (24 mm). The arrangement (b) produced big voids around the bolt. But for the 0.95 in. (24 mm) hole, arrangement c, the mixture was the best. It was corroborated with the pullout tests results where there is a difference in grout stiffness: the 0.95 in. (24 mm) borehole is about 10 times higher than a borehole with diameter 1.14 in. (29 mm). On the other hand, for the cohesive strength the difference is not significant. Numerical models were built to simulate the pullout tests, and also to simulate the roof support at an intersection. Convergence at two underground intersections, consisting of an immediate roof with laminated sandstone, was monitored to evaluate the performance of the roof supports, using the 1.14 and 0.95 in. (29 and 24 mm) diameter boreholes (i.e. arrangements ?a? and ?b?). The convergence readings showed that the 0.95 in. (24 mm) borehole diameter resulted in a smaller, although it was not significantly different.

Jan 1, 2008

By W T. Yen

Pyrrhotite crystallises as either a hexagonal or monoclinic structure, both of which can occur in ore deposits. In general, pyrrhotite is not considered as a valuable mineral unless it contains considerable amounts of other metals like nickel or copper. In fact it causes numerous problems in flotation including intensive oxygen consumption, which results in poor selectivity among sulphide minerals in the processing of complex sulphide ores. Also, because of its high sulphur content, pyrrhotite is a major contributor to environmentally detrimental sulphur dioxide (SO2) emissions from smelters. Pyrrhotite also interacts galvanically with grinding media via electrolyte species present in the flotation pulp, resulting in media corrosion. The most effective way to reject pyrrhotite is through a separation stage, which may be difficult when both types of pyrrhotite are present in the ore. In this regard depression of pyrrhotite through a flotation stage may be applied. Pyrrhotite depression by either intensive oxidation or by using sodium cyanide has been practiced. Results present in this work show that NaCN can depress pyrrhotite effectively when combined with an alkaline environment and low collector concentrations.

Jan 1, 2002

By David I. Smith, Kenneth Arnold, Bryan Aweh, Vincent Falkowsk, Brian Lakin, Andy Fer

Nassau County, New York, is undertaking several projects to improve the water quality in the Western Bays of Long Island. A major step forward will be the completion of the Bay Park Conveyance Project, which will divert most treated effluent away from the Western Bays to an existing ocean outfall at the Cedar Creek Water Pollution Control Plant. The ongoing works include 3.6 miles of microtunneling, 7 miles of sliplining, 14 shafts, and a 75 MGD pump station. This paper provides an overview of the design and an update on construction progress through December 2022. The project is a collaborative effort between Nassau County, New York State Department of Environmental Conservation, the design-builder, and various consultants.

Jun 13, 2023

The Skorpion process comprises three processing steps, atmospheric leaching in sulphuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the route causes of the crud formation in the solvent extraction circuit and optimisation strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica

Jan 1, 2007

By Tanveer Jahir

With increasing energy costs and mounting government pressure to adopt low emission, green sources of energy, it has become imperative to develop long-term sustainable underground infrastructures that exhibit low power consumption. Underground mining environments are mandated to have ventilation systems in place to replace polluted air with clean air. Continuously running air ventilation systems have proven to be an expensive solution for this requirement. Ventilation-on-demand (VOD) is a cost effective method for not only reducing energy consumption and greenhouse gasses, but also ensuring the safety and well-being of the miners beneath the surface. VOD is achieved by monitoring the air quality in target areas of the mine, and based on variables such as the number of personnel in the area, the number of emission-emitting vehicles, the air leakage around doors and entrances, dust levels, and other key environmental details, the speed and angles of the fan blades are adjusted to increase or decrease the volume of air flow. For over 40 years, Conspec Controls has been developing systems capable of VOD through the use of controllers, gas monitors and personnel/vehicle tracking equipment, providing inexpensive, reliable solutions for underground ventilation.

May 1, 2011

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

Whilst much has been written in past years by geologists, scientists, mining engineers, etc., regarding the well·known and justly notorious anticlinal, or, as they are more commonly known, " saddle" reefs of Bendigo, comparatively little noticehas been given to the synclinal or "inverted saddle "reefs and their relationship with each other. In taking up the question of the synclinal folds, I recognise that it is a large undertaking to confine within the limits of a short paper, and at the same time convey a comprehensive idea of their characteristics, and the importance of their relationship with the anticlinal folds, in the general question of practical mining. However, from a practical point of view I consider the question of great importance, and if an interest in it can be awakened, more particularly among practical men, the object of this paper will be achieved.Before entering into the subject I must briefly state some facts, and perhaps some theories, in respect to the deposition of the Lower Silurian rocks, and their subsequent buckling up, as now seen on the Bendigo gold-field. At the same time, I do not intend to go very closely into the geological aspect of the question, as I wish the paper to be considered as a practical one.

Jan 1, 1902

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining Co.'s Granite Mountain shaft. How this insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the lire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest pro¬ducer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

By Richard J. Mainiero

The Bureau of Mines conducted research to evaluate the optimum design for a rock-breaking explosive charge that could be fired unconfined in a gassy or dusty coal mine without the danger of igniting the flammable atmosphere. Charges of various shapes, with and without cavities, were tested in a gallery using 3-by 3-by l-ft concrete blocks as simulated boulders. For these tests the optimum charge, in terms of cost, weight, and convenience in handling, consisted of a flat l-1/2-lb charge of permissible explosive seven-eighths of an inch thick and 7 in in diameter encased in a l/2-in thick layer of fine salt (NaCI). This work demonstrated that it should be possible to produce an inexpensive explosive rock-breaker charge that would be safe to use in underground coal mines.

Jan 1, 1982

By Daniel G. DiCanio

Investigation of the costs of industrial accidents dates back to the 1920s. The Bureau of Mines was one of the pioneers in accident cost investigation with numerous studies published between 1928 and 1933. The bulk of these early investigations dealt only with costs which appeared as payouts on company books; that is, the direct cost of insurance premiums and the costs of medical expenses which resulted from industrial accidents. These early investigations, especially the Bureau's study of accident costs in Pennsylvania and Indiana coal mines provided the first real evidence that promotion of industrial safety pays back in dollars as well as in human life and wellbeing. In the 30s and 40s, investigations began to accumulate evidence that industrial accidents impacted more than just the direct operating expenses of a company (i.e., higher insurance premiums). The work of Heinrich pioneered these investigations, and produced strong evidence that the un¬insured costs of accidents far outweighed those costs covered by insurance. Heinrich developed and published a ratio of insured to uninsured costs of 1.4. Despite his cautionary statements about blanket application of this ratio it is used even today to estimate total costs of accidents. Simonds, in the late 40s and early 50s, extended the definitions of uninsured or indirect accident costs and developed what is now regarded as the principal method for estimating the total economic impact of industrial accidents. Simonds' method served as the basis for development of the logic of the Accident Cost Indicator Model (ACIM). However, several departures from Simonds' method were made to satisfy certain requirements imposed by the Bureau of Mines, and because information gathered during the course of our investigation justified a departure. These departures are noted in the discussion which follows.

Jan 1, 1977

By A. J. Davidson

A Cu-conducting solid electrolyte was used to develop the sensor. Instead of measuring the potential across the electrolyte from the reference material to the Cu-containing phase, a potential was applied and the stable current measured. This gave reasonable readings for copper-tin alloys, which agreed with the theoretical calculations, but was less satisfactory in the case of mattes because the surface area of electrolyte presented to the matte phase varied from sensor to sensor. To overcome this problem the potential was applied, the current was measured and then reversed and remeasured and the ratio of the currents was calculated. The current ratio is shown to be independent of the resistance of the electrolyte and the surface area of the electrolyte offered to the melt, but strongly dependent on the activity of the copper

Jun 21, 1905

By K. Schrijver, G. Beaudoin

"Four occurrences of galena-cemented sandstones, exposed in the Lower St. Lawrence - Gaspésie area, are described. They constitute a new, insufficiently explored type of deposit in Quebec.One mineralized body, a minor occurrence, is hosted in Lower Devonian rocks deposited in an estuarine, intertidal river channel during a marine regression; major cements are dolomite and sulphides. Another occurrence, a drilled prospect, is hosted in Upper Silurian rocks deposited unconformably on Cambro Ordovician basement during a marine transgression. With galena and quartz as main cementing minerals, it is similar to some well-known, economic sandstone-lead deposits. A third and fourth, a drilled prospect and a minor occurrence, are hosted in Upper Cambrian rocks deposited on continental slopes. In both, sulphides mainly occupy a secondary porosity. The differences between the third and fourth occurrences are: (1) cementing translucent minerals (carbonates and barite in one; chlorite in the other); (2) chronology of final subsurface dissolution (prior and subsequent to sulphide precipitation, respectively); and (3) important fracture porosity only in the barite-bearing deposit.The diversity of the four occurrences, and the unequal geological knowledge of their respective features, prohibit the formulation of uniform guidelines for further exploration.IntroductionThe attention of the mineral exploration community is drawn to four occurrences of galena-cemented sandstones (Fig. 2A) in the Cambrian of the Taconian Orogen and in the Siluro-Devonian basin of the Lower St. Lawrence and Gaspésie area (Fig. 1). In view of the fact that sandstone-lead deposits (Bjerlykke and Sangster, 1981) are, or have been, mined in several countries (e.g . Laisvall in Sweden: see Rickard et al., 1979; Largentiere in France: see Foglierini et al., 1980), the mere presence of occurrences in Quebec indicates that the mineral potential of some parts of the Appalachians requires further evaluation.Exploration for the deposits considered here is essentially restricted to geological methods and drilJing (e.g . Mainguet Suares and Samama, 1969), since the response to geophysical methods is virtually nil, at least in the initial, surficial stage of an exploration program. As the particular disciplines of geology utilized in exploration depend a great deal on the geological setting of a mineral occurrence, the diversity of the Quebec deposits is of prime importance. Therefore, the four occurrences (Fig. I, Table 1) studied by the authors are herein briefly described with emphasis on their stratigraphic and tectonic setting, and on the evolution of pore space and sequential occlusion of pores and fractures. Prior to further research in and around the occurrences, now in progress (e.g. Beaudoin, 1987; Beaudoin et al., 1987), it is hoped that the following outline will be useful to the explorationist."

Jan 1, 1987

By Máximo Pérez, Julio C. Videla, Rosa Dzioba

"This paper reports the hydrometallurgical treatment of gravity concentrates of gold samples and outcrops associated with graphite ores obtained from:• flotation tailings of crystalline graphite minerals• outcrop samples of graphitic rock associated with auriferous minerals and free gold located in the Villa Union district and surrounding areas - La Rioja Province - Argentina.Previous studies of the flotation potential of crystalline graphite minerals failed to consider the presence of noble metals.The samples represent a mineralized zone of crystalline graphite which is distributed in different formations with a NE - SW trend in Maz, Punta Colorada and Las Ramaditas hills, covering an area of about 300 square kilometers."

Jan 1, 2003