Search Documents

By Paul Hewitt, Tim Smirnoff

Design and construction of the Epping to Chatswood Rail Line tunnels in Sydney, Australia required an innovative approach to define hydrogeological properties of the Sydney Hawkesbury Sandstone and provided an insight into the hydraulic behaviour of fractured sedimentary rocks. To meet restrictive water inflow and infiltration criteria both the pre-treatment of zones of fractured or highly jointed rock, and waterproofing using an interior spray on membrane for the finished drained tunnels and stations was required. Methods typically used to address the interaction of groundwater and tunnels in the Sydney Basin are demonstrated by case histories from major design-build tunnel projects.

Jan 1, 2005

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By D. J. Dollhopf

This research was part of an effort to investigate means of reestablishing non¬polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. Chemically undesirable overburden material was selectively backfilled with the intent that it would be below the future root zone, be above the reestablished aquifer, and would not be leached as a result of deep percolation. After 2 years the buried material remains above the spoil aquifer and below the maximum rooting depth. Unsaturated water flow from the land surface to the buried material occurred during wet climatological periods. No significant leaching of buried material was observed, however. Overburden sample contamination from drill stem joint grease with Pb, Zn, and Cu additives caused substantial error regarding DTPA extractable trace metals. A grease with teflon and talc additives was recommended for use in future sampling programs. DTPA extractable trace elements in overburden material had no statistical relationship to post-mine ground-water quality. Overburden columns leached with water produced leachates comparable to overburden and spoil ground-water trace metal quality. A depositional model described the Rosebud Coal overburden as a fluvial system with distinct units of sand, silt, and clay, with distinct chemical properties. Physical and chemical characteristics of the model were comparable to the in situ geochemical system, a relationship which may aid in locating overburden materials unsuitable for reclamation.

Jan 1, 1979

By Rushikesh Battulwar, Javad Sattarvand, Joseph Seamons, Masoud Zare

In the last decade, new developments took place in the area of indoor positioning (or localization). Since the Global Navigation Satellite System (GNSS) cannot be used in underground mines, other technologies are needed for localization. Positioning and communication options today primarily include Wi-Fi, Bluetooth Low Energy (BLE), Ultra-Wideband (UWB), Radio Frequency Identification Device (RFID), etc. Smartphones and tablets currently have an array of sensors and radios, which can provide valuable information to allow indoor localization via various methods. Where mineworkers could keep smartphones with them, they can be highly effective at enabling localization and navigation. Recent applications of these technologies in underground mines have been thoroughly reviewed and examined for the likelihood of their utility for accurate localization where no other means exist. Some critical challenges and gaps that need to be addressed in future research have been identified.

Sep 5, 2021

Vitrinite reflectance forms the basis of a study of coal rank variation in two areas of the Upper Hunter Valley, New South Wales, on the northern margin of the Sydney Basin. A selective analysis procedure, based on samples rom twenty-two boreholes, has resulted in a small range of reflectance values for each sample and consequently a high degree of significance for calculated mean values. The patterns of rank distribution derived from these data have facilitated an interpretation of the rclative timing of coalilication and deformation in each area.This study provides support for the suggestion by several authors that there were at least two periods of folding in the tJpper Hunter Valley. In the Hebden-Ravensworth area, minor folding took place after most of the coalilication was completed.To the west, in the region of the Muswellbrook Anticline, coalification occurred during or after the formation of this major structure. Tectonic instability during deposition of the Singleton Super-Group, in the region of the Hunter-Thrust on the basin margin, is evidenced by rank variation suggesting differential subsidence across this zone.

Jan 1, 1980

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991

By D. R. Parrish, F. F. Craig

In some respects, forward combustion (alias: fie-flooding, underground combustion, in-situ combustion, dry combustion) is an efficient oil recovery method. For example, its displacement efficiency (as much as 95 percent in reservoirs with high porosity and high oil saturation) is good. In its use of heat, however, forward combustion is grossly inefficient. Most of the heat generated during forward combustion is wasted. About one-fifth of the heat is picked up by the incoming air and re-used (regenerated); the remainder is left behind the combustion zone and ultimately is lost. Compressed air is expensive, and heat generated from compressed air via underground combustion is too valuable to be thrown away. Improvement is needed. Since the early 1950's, improvements in forward combustion by addition of water injection have been discussed, particularly in the patent literature, with increasing frequency.'-'' These concepts are based on the fact that relatively inexpensive water can be used to pick up much of the heat that is ordinarily wasted during forward combustion, and transport it forward to a more useful place, thereby reducing the amount of air required to move a heat front through the reservoir. Several approaches have been proposed. Merriam and Squires1 taught that a combustible (fuel) gas should be injected along with the air and water. This, however, would give at least a tendency toward reverse combustion instead of forward combustion, and would reduce the velocity of the heat bank, defeating the primary purpose of the water injection. Pelzer2 described primarily a batchwise method of forward combustion and water flooding. He advocated burning part way through a reservoir with forward combustion, then switching from air to water injection alone to push the heat toward the producing wells. Though possible, this method has serious disadvantages, the major one being that, by the time water injection is started, much of the heat has been irretrievably lost to the overlying and underlying formations. We have described what is considered a practical Combination Of Forward Combustion And Water-flooding (COFCAW).3,4 Air and water are injected simultaneously (or alternately) after a small heat bank has been formed by forward combustion. Some of the injected fluid fills up the region behind the heat bank; the rest enters the heat bank. Upon encountering heated rock, the water is converted into steam, which then flows ahead of the combustion zone and displaces much of the oil in place. Only enough air is injected to provide heat for vaporization of the water and to compensate for reservoir heat losses. Since the size of the heat bank is minimized, heat losses also are minimized. Because of more efficient oil displacement ahead of the combustion zone, fuel consumption is reduced. Too, unlike a forward combustion zone that cannot move until all fuel at a point has been consumed, COFCAW leaves some

Jan 1, 1970

By D. F. Malott

The Michigan Dept. of State Highways makes extensive use of geophysics for subsurface surveying which would be applicable for uses in other fields. Examples of resistivity surveys are given which include a proposed large-volume excavation with suggestions for land use after excavation, subsurface evaluation for engineering design, and a subsurface survey for land appraisal. An example of a combined refraction seismic and resistivity survey is shown where the resistivity is used for outlining the unconsolidated soils, while the seismic method is used to outline bedrock and to evaluate it for rippability. A refraction seismic survey at the bottom of bridge caissons for evaluation of bedrock uniformity and a rehtive aid in assessing rock strength is reported. These past several years have been a period of unprecendented construction and commercial expansion. Vast private manufacturing complexes and government road, power, and office projects are being built or are in planning stages. Nearly everywhere, municipalities are expanding outward and upward. Many towns are developing into cities and many cities are displaying new skylines, and the building boom shows little sign of slowing down.

Jan 1, 1970

By Maxwell Gensamer

Jan 1, 1960

By R Munoz, R González, J Vallejos, A Delonca

In panel caving in underground mines, it is essential to characterise and monitor the stress and stability state of production level pillars to ensure the extraction of the mineralised ore column and the safety of workers. Pilar Norte is a sector in the El Teniente mine that forms a pillar between the undercut fronts of the adjacent Esmeralda and Reservas Norte sectors. It exists in a high-stress environment, which may induce damage to the rock mass production pillars. Generally, numerical models are calibrated using observed damage in galleries. This procedure does not discriminate between the structural condition and/or the blasting damage effects. This paper proposes a technique that uses borehole cameras to measure stress-induced damage. This has the advantage of being at the intact rock scale, meaning that the effect of geological structures is negligible and the blasting damage factor is eliminated. Comprehensive geotechnical characterisation and tomography monitoring has been undertaken at Pilar Norte to describe and determine the rock mass behaviour of the production pillars. By combining analytical, empirical and numerical models, a correlation between the measured overbreak recorded by the borehole cameras and the stress level of the pillar was developed. The methodology can be routinely applied to estimate the stress state in the production pillars.CITATION:González, R, Munoz, R, Vallejos, J and Delonca, A, 2016. Characterisation and monitoring of the stress state of production pillars at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

China has made great progress in thick coal seam mining, commonly characterized by longwall top-coal caving mining and single-pass longwall mining with a large cutting height. At present, the maximum mining thickness of longwall top-coal caving reaches 20 m while that of single-pass longwall mining approaches 8.8 m. The top-coal caving–related technologies have significantly improved the mining efficiency of thick coal seams and have also made a great contribution to the centralized underground mining of coal. Thus, the number of underground coal mines is greatly reduced in China. However, due to the increase of the mining height and the changes in mining operations, the overburden movement caused by the mining of thick coal seams is more intense, and the influence scope is larger, which brings a series of new problems on ground control of longwall faces. In order to enhance ground control and improve the mining efficiency of thick coal seams

Jul 28, 2020

Upon cessation of mining activity open-cast mine pits typically fill with water, forming a æpit-lakeÆ. The water in these lakes, in some instances, contains high concentrations of ædeleteriousÆ material. Containment and/or dilution typically requires an understanding of how stratification in the pit-lake will develop over a long timescale (say 100 years). Vastly different transport rates can develop due to differing hydrogeochemistry, basin morphology and climate. Numerical (computer) modelling is the most likely approach for successful prediction over long times. While lake modelling tools are available, useful numerical modelling requires improved understanding of transport in such systems because they are different to natural lakes in a number of ways. Notwithstanding the effort required to improve our understanding, the modelling provide a means of testing approaches to active management of pit-lakes.

Jan 1, 2002

By I D. Gregson, A S. Garcia, K M. MacAndrew

The design work undertaken by Rock Mechanics Technology (now part of Golder Associates (Golder)) has played a major part in successfully establishing mechanised room and pillar working in Indian coalmines, both for the development of new districts and for the re-establishment of old districts prior to pillar extraction on panel retreat.Golder has used appropriate design of pillars, extraction sequences and final snook sizes to minimise ground control risks during pillar extraction. Where the strata will not cave reliably, partial extraction systems leaving either a crush pillar or a substantial yield pillar have been adopted.Remote monitoring of selected pillars during the extraction process using stress cells, extensometry and convergence measurements provides confirmation of pillar behaviour and verification of designs.A new telltale device, giving a visible warning of impending caving, is now installed at all Indian pillar extraction sites and is proving very successful.CITATION:MacAndrew, K M, Garcia, A S and Gregson, I D, 2014. Coalmine pillar design and performance during mechanised pillar extraction in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 347–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

A Good Product Range - So What! While in terms of water, waste management and environment protectrion, the Gippsland Basin may appear to have a good product range, what does this really mean? What it means is that, like any product range, the virtues of the product range must be sold and accepted by a majority of the public. The social, economic and environmental benefits of any enterprise using these products must be sold and accepted by the regional population. Many a budding entrepreneur has failed because he assumed that the public would accept his product, so good did it appear to be! However, we know that such an assumption must be avoided and that a great deal of time and effort needs to be invested in promoting and gaining acceptance of a product to ensure a long term and viable market.

Jan 1, 1992

Fragmentation Characteristics of Iron Ores from Anshan, China

Sep 13, 2010

By Robert A. Jankowski, J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200- to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By A D. Stewart Gillies

Resource rent taxes are taxes which only become effective at such a time as a pre-determined rate of return has been achieved by an operation. Resource Rent Taxes have from time to time been considered for implementation in bothAustralia and New Zealand. The offshore petroleum industry in Australia is already subject to RRT as is the Roxby Downs (Olympic Dam) Mine in South Australia. Both the mining and petroleum taxation regimes in Papua New Guinea include a resource rent tax component called Additional Profits Tax.   The implications of the current form of additional profits tax for shareholder cash returns are that the tax burden on the operation may suddenly increase at some stage in the life of the mine if and when the threshold level of profitability for the tax to be triggered is exceeded. From that point in time onwards the cash return to the shareholders on the capital invested is greatly diminished. For mining companies in Papua New Guinea, the effective tax rate increases from 35% to 57.75% as a result of the onset of additional profits tax. This tax rate penalty is so severe that there appears to be merit in considering the concept of managing profitability through time rather than purely maximising annual pre-tax profits as is currently the case in most mining operations. This would have the benefit of deferring or perhaps preventing altogether the onset of the tax. One possible method for the effective management of profitability is through the control of average mining grade by cutoff grade manipulation.   Traditional cutoff grade theory has usually considered taxation as a direct cost at a fixed or variable percentage of annual profits. As a result of this most analyses are conducted on a pre-tax basis. If tax is included in analyses it is usually present as a time independent function of gross profit. Additional profits tax is both time, and rate of return dependent and therefore not adequately accommodated by currently accepted cutoff grade theory.   A review has been made of the effects of resource rent taxes on both the investment decision-making process as well as possible development and mining strategies which may be employed by mining companies faced with resource rent taxes. The review includes examples based on the structure of additional profits tax which is levied in Papua New Guinea.

Jan 1, 1995

By Priscilla P. Nelson

Many concepts concerning equipment selection, performance prediction, and evaluation of support requirements for tunnel construction in soil or hard rock tunnels cannot be extrapolated directly for application in soft rock (compressive strength between 1.0 and 35.0 MPa). Case histories for small diameter (less than 3.5 m) tunnels in Austin, Texas, are analyzed to gain insight into particular problems encountered during tunnel excavation in weak sedimentary rock, and the performance of different excavation systems are compared.

Jan 1, 1987

By Casey Erickson

Goldstrike Property ??Located in Elko, NV USA?Carlin Trend ??Mining Since 1985 ??27 Million Ounces of Gold Mined ??Production of 400,000 tons/day ??1,600 Employees

May 1, 2011