Search Documents

By T. Kunitake, H. W. Paxton

The self-diffusion coefficient of chromium in various alloys in the iron-chromium system has been measured. A variation in Dofrom 10-4 for pure chromium to a maximum of 102 near 60 pct Cr appears with a range of activation energy from about 50 to 80 kcal per mol. The general pattern of behavior observed is not consistent with present theories of diffusion by a vacancy mechanism. Suggestions are made for further clarifying experiments. RECENT work on the self-diffusion of chromium,' ?-uranium2-4 and ß-zirconium,23, 26 has indicated that these elements have very low Do (10-3 to 10-4) compared to that conventionally expected for vacancy diffusion. Pound et al.5 have suggested that this may be due to ring diffusion being operative, and have proposed a model which gives Do of the correct order of magnitude. The essential difference between this model and Zener's earlier model6 is that whereas Zener assumes tight coupling between atoms in a ring to establish a vibrational frequency, Pound's model allows the atoms to vibrate essen- tially each in their own normal modes. The probability of each atom moving in the correct direction to cause a ring of n atoms to rotate by 2p/n must then be calculated as a "synchronal entropy" which may be -20 e.u. for a 4 atom ring. In iron, the latest determinations of self-diffusion yield Do in the range 18 to 522.7-9 The most accurate is probably that of Borg and Birchenall8 which is 118 ± 3. This value is not inconsistent with that expected for a vacancy mechanism. Since iron and chromium are very closely similar in size, are both transition metals, and their solution is thermodynamically ideal at temperatures of interest in diffusion, it appeared that a determination of self-diffusion coefficients, Do and Q as a function of composition would be of substantial interest to diffusion theory. The following measurements were made with this purpose in mind.

Jan 1, 1961

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By Roxana Barrantes Huamán

El presente texto describe la geología económica del depósito aurífero Alpacay ubicado en Arequipa, Perú. El depósito Alpacay es un típico depósito mesotermal, filoniano que es explotado por la Cía Minera Yanaquihua, donde el mineral es procesado en una planta de cianuración, gravimetría y flotación. Costa. Asímismo, se realiza en la Franja Aurífera Nazca-Ocoña que alberga innumerables minas y depósitos en vetas angostas como Arirahua, San Juan de Chorunga, Chalhuane, Las Clavelinas, María Eugenia, entre otros. La alteración es básicamente argílica en la vecindad de las vetas y propilítica hacia el exterior.

Sep 12, 2011

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

RACAL COMMITTEE OF ARRANGEMENTS Henry McCormick, Chairman; David Watts, Secretary; H. H. Campbell, A S. McCreath, S H. Chauvenet, C. E. Stafford, George S. Comstock, Jones Wister, E. C. Felton, F. W. Wood, Harvey Fisher. CITIZENS' RECEPTION COMMITTEE Governor H. M. Hoyt, Hon John C. Herman, Hon Simon Cameron, Hon. J. D. Cameron, W T. Hildrup, Charles L. Bailey, W. W. Jennings, Lane S. Hart, H. U. Carter, Gilliard Dock, T. T Wierman, Jr, James Boyd, D. L. Jauss, Dr. T J. Dunott, S. C. Gilbert. William J Rose, James Lynah, Dr. H. B Buehler, William N Lamberton, John Wister, G. M. McCauley, David Fleming, John Q. Donney, M. E. Olmsted, H. S Gross, Henry Gilbert. John B. McPherson, Lyman D. Gilbert, F. W. Forman, L. S. Bent, A. J. Dull, F. R. Leib, Dr. G. W. Belly, James McCormick. The opening session of the meeting was held in the hall. of the Young Men's Christian Association, on Tuesday evening, October 25th. Mr. Jones Wister, of the Local Committee of Arrangements, introduced the Hon. John C. Herman, mayor, who, in a brief address, extended to the members present a welcome to the city, of Harrisburg ; Lieutenant Governor Stone made an address of welcome on behalf of Governor Hoyt and the Commonwealth of Pennsylvania. President Metcalf responded, on behalf of the Institute, to the cordial addresses of the mayor and lieutenant-governor. The following persons proposed for members and associates of the Institute, and recommended by the Council, were unanimously elected :* MEMBERS. William F. Aldrich, - Montevallo, Shelby Co., Ala. George H Blake, - Steelton, Dauphin Co., Pa. L. Bertram Cady, - Salisbury, N. C. John B. Church, - Pottsville, Pa. Walter S. Church, - Pottsville, Pa, Frank L Clark, - Pittsburgh, Pa. * In the following list are included those elected at a subsequent session of this meeting.

Jan 1, 1882

By Kevan Ford, Getulio Junior, Rob Henderson, Wayne Philips, Chris Martin, Rob Thorpe

"Plant 2 at the Kinross Paracatu gold operation in Minas Gerais State, Brazil, was commissioned in late 2008. Designed to be the largest tonnage, lowest grade gold milling operation in the world, Plant 2’s throughput has steadily increased towards its design capacity of 5087 tons per hour.The plant employs a gold-specific flotation scheme to recover the majority of gold, which is present as discrete free gold particles. Additional gold is recovered by jigs in the grinding circuit, and the jig concentrates are reground, upgraded and subjected to intensive cyanide leaching. The flotation cleaner concentrate is reground and leached using a conventional CIL circuit.One year after start-up, with the plant stabilizing operationally, plant circuit surveys were completed by a joint team from Kinross Paracatu and Blue Coast Metallurgy Ltd. The surveys audited the flotation and concentrate treatment circuits to investigate the metallurgical performance.This paper describes the Plant 2 operation and how the surveys were designed and executed. Some of the quality control systems that were employed to provide meaningful data from such a low grade gold ore are described and findings and actions taken to improve metallurgy as a consequence of the surveys are discussed.INTRODUCTIONThe Paracatu mine is located two kilometres north of the city of Paracatu, in the north western portion of the state of Minas Gerais, Brazil, 230 km southeast of the national capital Brasília (shown in Figure 1). The present day Paracatu mining operation, fully owned by Kinross Gold, through its Brazilian subsidiary Rio Paracatu Mineração (RPM) is designed to be the largest tonnage, lowest grade free milling gold operation in the world.The deposit currently hosts some 1.2 billion tonnes of ore at a grade of ~0.41 g/t gold, hence contains a total gold reserve of over 20 million ounces. At a designed plant throughput rate of 61 Mt/year the mine life goes beyond 2030."

Jan 1, 2011

Blasts should be designed so as to maximise the percentage of charges which shoot to a free face (Le, to a pronounced rock/air interface).Free faces should be rough, parallel and reasonably near to blastholes and, very importantly, concavely·biplanar relative to the charges (see Fig. 6b). The presence of biplanar free faces requires that each charge fragments and detaches its quota of the burden rock before the detonation of:1. later-firing adjacent charges in single-row blasts, and2. dependent charges in multi-row blasts.In multi-row blasts, biplanar faces are best achieved:1. by drilling blastholes on equilateral triangular grids,2. by selecting a VI, V2 or V3 initiation sequence, and3. by using down-the-hole delays.Biplanar faces start to be created only when the conventional value of effective blasthole spacing/effective burden distance (Se/Be) increases beyond about 2.4. Values of Se/Be less than about 2.4 result in planar free faces. Where biplanar faces are created, conventional values of Se/Be are invalid and appreciably greater than real values of Se/Be.

Jan 1, 1986

By C. Keefe, O&apos

Measurements of the quantity of entrained air within processes have challenged instrumentation developers for years. This is particularly true in the unique and demanding operating environment and applications seen in minerals processing. In minerals processing applications, entrained air plays a role in errors seen within nuclear density gauge measurements and in pumping efficiency. It is also the major component of flotation processes. The measurement of the quantity of entrained air, known as the gas void fraction, can now be performed from the outside of a process pipe through CiDRA?s patented passive sonar array-based technology. Within column cells, the need for a robust, no maintenance, accurate means of measuring the entrained air, known as gas holdup, has resulted in a submersible version of this technology. CiDRA?s meter technology calculates the gas void fraction by first measuring the speed at which naturally occurring sound in the process slurry propagates past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. A known relationship between this speed of sound and the entrained air captured in the form of bubbles within the slurry is then applied in CiDRA?s meter to calculate the gas void fraction. This paper will present the measurement technology, its operation, its calibration and its application in a variety of gas void fraction and gas holdup measurement situations such as pumping efficiencies, hydrocyclone operation, external sparging, and column cells.

Jan 1, 2008

Upgrading and Removing Phosphorus from Low-Grade and High Phosphorus Containing Iron Ores

Sep 13, 2010

Size Separation Pretreatment and Alumina Recovery from Bayer Red Mud

Sep 13, 2010

By C. C. Pretorius

3D seismic surveys have become a well-accepted method of imaging sub-surface geology in the Bushveld Basin. Because both the seismic sources and receivers are placed at surface, most surveys are limited to imaging faults with >=7 m throw. However, some areas such as shaft infrastructure can benefit from the ability to detect smaller structures prior to shaft sinking. Borehole radar and logs such as the acoustic televiewer can identify these structures in the shaft barrel, but not within -200 m from the shaft. Therefore, Anglo Platinum has developed the method of high-resolution 3D vertical seismic profiles (VSPs) for structural sterilization of shaft sites prior to shaft sinking. VSPs utilize a surface source and sub-surface receivers deployed down a borehole. This means that seismic energy goes through the near surface only once, and therefore suffers less frequency loss than when both source and receivers are on surface. Furthermore, VSPs can record 3 component (3C) data which comprises P wave, Sh (horizontal) and Sv (vertical) wavemodes. Because S waves travel at about 0.6 of the velocity of a P wave, shorter wavelengths and therefore higher resolutions are possible using S wave data. VSPs were first used in their one dimensional, zero offset, mode to correlate borehole geology with seismic stratigraphy within seismic surveys. This showed that VSPs record -30% higher frequencies than surface seismic surveys. The program then applied two dimensional VSPs to the problem of imaging geological structure close to a borehole. 2D VSPs confirmed that high frequency results could be achieved, and that this enabled a more accurate image of the Merensky Reef than could be achieved by surface seismic data. Finally, the program has achieved the successful recording and processing of 3D VSP data, with both compressional and shear wavemodes giving a high resolution structural result. Although P wave data gives -30% frequency improvement over surface seismic surveys, S wave data can give as much as 80% improvement, further improving the structural image achieved. The high fixed costs of VSP surveys mean that they should ideally be run in multi-client batches, which can reduce the per borehole cost by up to 50%. Their application is anticipated to be on high value capital infrastructure with a geological risk from faults which are not imaged by surface seismics-generally in the sub-7 m range. Keywords VSP, 3D seismic, bushveld, platinum, resolution, imaging, shear waves, shaft sinking.

Jan 1, 2011

By W. P. Erasmus

This paper will focus on the use of the ?wet-mix? steel fibre re-in forced shotcrete as a permanent lining in deep shafts, assessing gold bearing reef. It will cover all aspects relating to the choice of this material covering the geological conditions through to the final quality control. All procedures are in line with ISO 9001,as JCI projects who manage the project, are an approved company therof.

Jan 1, 2001

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries. The typical converting operation involves lateral purging of air into molten matte through a bank of tuyeres. This blowing operation occurs at low pressure from the blowers, resulting in a bubbling regime that is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks also include recurrent tuyere blockage, tuyere punching, and low oxygen efficiency.Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to industrialscale tests, a numerical assessment to ascertain the feasibility of implementing sonic injection into a PSC was conducted. The work included flow characterization at high-pressure injection achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid method together with the RKE turbulence model to account for the multiphase and turbulent nature of the flow.This paper discusses the key findings in understanding plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a full-scale implementation of sonic injection in the smelter."

Jan 1, 2015

Ore from the Hill 50 Gold Mine, consists essentially of pyrrhotite, with minor amounts of pyrite, chalcopyrite, galena and gold, replacing "jaspilite." The gold is associated with the sulphides as shotty particles. About 8 per cent. of the particles are less than '0.010'mm.The Hill 50 Gold Mine, at Boogardie in the Murchison goldfield, about 300 miles north-west of Kalgoorlie, was first operated in 1898. From 1898 to 1917 it yielded 20,000 short tons of ore for a recovery of 6,225' fine oz. gold, equivalent to a recovery grade of 6.22 dwt. gold per ton.The present company since the beginning of its operations in September 1936 to June 30, 1954, produced 811,081 short tons of ore for a recovery of 242,554 fine oz. of gold, equivalent to a recovery grade of 5.98 dwt. gold per ton.The grade of ore (recovery grade) has shown a remarkable variation with depth. From the 120 ft. Ievel to the 300 ft. level, it averaged about 7.5 dwt. Au per ton. Below the 300 ft. level it declined, and from 300 ft. to 400 ft. averaged 4.9 dwt. per ton, falling further with increasing depth to about 4.5 dwt. per ton at the '600 ft. level.On the 820 ft. level the grade improved sharply to about 14 dwt: per ton, and this grade has persisted down to and on the 1060 ft. level.The orebody has been described by Finucane (1953) as a series of lenses of finely banded jaspilite conformably enclosed by greenstones. The jaspilite is tightly folded and faulted and intruded by dykes of felspar porpnyry.Mineralization is practically restricted to the jaspilite.

Jan 1, 1955

By Ruddle R. W.

Solid mattes are generally held to be either (a) eutectiferous mixtures of the component sulphides Cu2S and FeS or (b) mixtures of complex sulphides. This chapter shows that liquid mattes consist essentially of a homogeneous phase in which iron, copper and sulphur are present. The amount of sulphur is generally less than that required to account for all the metals as stoichiometric sulphides; mattes cannot therefore be regarded as mixtures of FeS and Cu2S. Some iron oxide may be dissolved in the sulphide phase and magnetite is often present as a second phase. If the sulphur content of the matte is reduced the composition enters the miscibility gap in the ternary system and either an iron- or copper-rich solution (depending upon the composition of the matte) separates as a new phase. On solidification any one of four phases (iron, copper, Cu2S and FeS solid solutions) may crystallize as primaries. The remainder of the matte solidifies as a ternary eutectic. It is possible that iron oxides enter into this eutectic. Knowledge of the ternary Cu-Fe-S system is far from complete and nothing is known of the quaternary system Cu-Fe-S-O

Jan 1, 1953

Raw materials account for over 60 per cent of the cost of hot metal production in classical blast furnaces and the principal cost component is cost of coke. Dependence on coke is a traditional weakness of blast furnace ironmaking and while efforts have been made to evolve alternative ironmaking technologies which do not use coke, such as direct reduction, smelting reduction, and the more recent method of making iron carbide, blast furnaces continue to be the most efficient means of producing bulk hot metal even today. Coal injection, to the extent of 150 - 200 kg/t of hot metal, has been one of the major innovations made in blast furnaces to decrease cost and to reduce the dependence on coke. This has, however, given rise to more stringent coke property requirements (which often means more expensive coke) - a `tail spin' of Sorts!

Jan 1, 1999

Ground and air vibrations induced by large surface blasts have been monitored. These field results, as well as a large number of published results, have been used to assess the performance of existing predictors and for the development of improved prediction methods. Field monitoring has been performed, with four seismographs giving complete wave records, at limestone quarries, coal strip mines and an open pit copper mine. Conventional analysis includes least square fitting of peak particle velocities and peak air overpressures with scaled distance formulations. Frequency content has been analyzed, and correlated with blast design (detonation sequence). Two new methods have been developed for predicting ground vibrations induced by blasting. The proposed analytical predictor accounts explicitly for inelastic attenuation and geometrical spreading, and calculates the peak particle velocity as a function of charge weight and distance. Statistical analysis of case studies confirms the consistent improvement over conventional scaled distance predictors. The second new predictor is a computer program simulating blasts, including blast geometry, charge distribution and detonation sequence, and simulating propagation of individual pulses to any point of interest, where effects are summed. A complete blast vibration results, allowing prediction of frequency content and duration as well as peak velocities.

Jan 1, 1983

By Leping Liu, Li‑Ting Chen, Sachin Urade, Pengbo Chu

Mining industry requires constant adaptation to its practices in response to the dynamic change of the societal demand. Little information exists regarding how the US metal mining engineering education is prepared to meet with its industry needs due to the increase in critical minerals driven by the green energy transitions. This study aims to provide industrial perspectives on the current US metal mining engineering education and areas for improvement. An online survey with both closed- and open-ended questions were designed to seek opinions from the US mining industry. Findings indicated a shortage of qualified graduates from the current US metal mining engineering education system. The qualifications need to be improved include engineering sciences underlying mining methods, mining design experience, mining feasibility study, the connection between theory and practice, and understanding of the overall mining operation. The survey also identified future desired qualifications. The most desired ones in the next 5 years include an ability to acquire and apply new knowledge as needed and sufficient experience in the field. Respondents, regardless of the nature of their affiliated mining companies, unanimously recommended that collaborations between the industry and academia should be enhanced. The analysis of the results concluded four recommendations: (1) involve more multiple stakeholders in reforming mining education programs, (2) reinforce field experiences as a key part of mining engineering education programs, (3) enhance a closer collaboration between academia and industry, and (4) integrate emerging technologies (e.g., artificial intelligence/virtual reality) guided by pedagogical theories into new mining engineering curriculums.

Jun 26, 2023

By Steven L. Anderson

A cut-off wall has been designed and is currently under construction along the Back Dam of the existing tailings impoundment at Red Dog Mine, Alaska. The cut-off wall, which will be in the order of 5,000 ft long and up to 150 ft deep, when complete, is being excavated using a 40 metric ton Bauer trench cutter head mounted on a Liebherr crawler crane, in combination with a closed loop slurry pumping and de-sanding system. The tailings impoundment is situated in an area of warm permafrost and high potential seismic activity. Design incorporated an assessment of rock jointing to define the final depth of the wall along the alignment requiring the use of plastic concrete backfill to address the concerns associated with potential cracking of the wall due to settlement and during seismic activity. The results of the geotechnical investigation program, particularly with respect to variation in rock hardness along the wall alignment are discussed, as are the design criteria for the plastic concrete backfill, the challenges faced during construction, including scheduling of the work with the on-going dam raise activities of the mine, and the lessons learned with respect to potential productivities and selection of cutter wheels and teeth. Also described are the requirements for and advantages of utilizing a slurry boosting system to meet pumping requirements, re-design of the plastic concrete mix to consider workability and optimization of cutter teeth configurations to reduce wear through highly varied rock hardness.

Jan 1, 2010