Search Documents

By B. P. Watson

The first crush pillars on the Bushveld platinum mines were introduced at Union Section in 1978. Before the introduction of crush pillars, serious problems were experienced when stoping advanced to a point 30 m to 40 m on both sides of the centre gully. At least three to four stopes were collapsing per month. The introduction of the pillars stopped the stope collapses in the mining area where they were introduced. The residual stresses of these pillars were never measured; however, the successful elimination of the ?back-break? problem suggests that the original pillars had a residual strength of at least 8 MPa. Apart from back analyses, very little work has been done to determine the residual strength of crush pillars and only very recently have any measurements been made. The lack of knowledge in this field has resulted in pillars being designed based on experience. Concerns about stope collapses, similar to the Coalbrook disaster, have led to larger pillars being cut in more recent times. If such pillars were cut in brittle quartzites they would always fail violently but the ductile nature of the Merensky Reef generally allows large pillars to fail without bursting. Occasionally, however, one would burst in a working area. Increased incidence of bursting has been reported on some mines at deeper levels but most of these bursts occur in the back areas. Nevertheless, the incidence of bursting increases the risk of falls of ground in already dangerous areas, and the larger pillars decrease the extraction ratio. This paper describes the evaluation of stress measurements conducted in two boreholes over a crush pillar with dimensions 2.5 m x4.0 m, and a height of 1.2 m. Boussinesq equations for vertical and shear stress were used to analyse the original measurements and provide a stress profile across the pillar as well as the residual strength of the pillar. The results showed an unexpectedly high peak stress of 280 MPa at the centre of the pillar and a residual strength of 48 MPa. The reason for the high residual strength is suspected to be the result of the stiff environment under which the pillar failed and the small height of the siding on the up-dip edge of the pillar. More measurements should be conducted on several mines to establish a range of residual strengths for narrow crush pillars.

Jan 1, 2008

The extent of regional stratigraphic and structural geological mapping so far carried out in Australia is likely to be greatly overestimated by uncritical inspection of the latest authoritative geological map of the continent-that so ably compiled by the late Sir'T. W. Edgeworth David. Vast areas geologically coloured on this map are in fact known only from the most meagre field data, some of Which even include observations of distant views from which the so-called "geology" has been indicated in' reconnaissance reports.This applies to large areas in Cape York Peninsula; the plateau of Arnhem Land, and its margins except on the west where the Pine Creek mineral belt is better known; to the Desert Basin of Western Australia, practically the whole of the western half of the Northern Territory, much of east-central Western Australia, and northwestern New South Wales. Other vast areas are, more happily perhaps, left blank. It is true that prospecting parties have, at various times and with varying degrees of thoroughness, traversedparts of these little-known regions, often, however, in the search for gold or the.more obvious types of metalliferous mineral deposits and, furthermore, too often without leaving any written account of their examination, or with very sketchy details supplied. Unpublished geological surveys also cover some parts of these regions, but, on the whole, the picture we can draw of the regional deployment of rock masses in Australia is far less full than even David's map, with its obvious blanks, presents to us.Lest the practical mineral seeker among us should be inclined to place too much reliance on the prospecting to which I have referred.as giving him a straight hint of what country to keep out of, we may point to the recent discovery of a major sedimentary basin in the east KimberllilYs on which Dr. Teichert will have more to say. And that there are new metalliferous mineral deposits to be foundin parts of these little-known areas no one can doubt, for, after all, new discoveries are made from time to time in areas so well-known as the Victorian gold-fields. I take it then that regional geological mapping is a necessary concomitant of the further development of Australia's mineral resources-but I am not of the school that places it first on the list of priorities, and furthermore I believe that there can be a royal road to regional mapping-an inspired approach based on knowledge already gained and led to fruition by field surveys in key areas, by which there may be obtained a result giving a significantly close approach to actuality with only a fraction of the work that would be required for detailed field surveys on a systematic basis. I believe that a policy of rapid reconnaissance of such a type should be adhered to, especially in view of present deficiencies in numbers of geologists available for all purposes in Australia. The details that must eventually be sought can, I believe, be filled in later as the whole country becomes more developed and amenable to detailed surveys.

Jan 1, 1950

By A. Uiga

The U.S. Bureau of Mines funded a project which addressed objectives concerning irrigation of native plants and inoculation of native plants with vesicular-arbuscular mycorrhizal (VAM) fungi. The specific irrigation objectives were 1) to demonstrate the performance capabilities of solid-set irrigation for reclaimed mineland conditions, and 2) to demonstrate and evaluate three irrigation concepts under two separate water supply conditions. The VAM inoculations were to assess irrigation benefits in establishing VAM relationships for transplanted native species. Following the seasonal demonstration (May to September 1983) at 3 separate mine sites, conclusions were made that apply to the 6 state Western mining industry. The demonstration sites were located in Montana, Wyoming, and New Mexico. Positive conclusions were reached for 1) the use of soil moisture sampling with or without irrigation, and 2) the selection of solid-set sprinklers as the irrigation method. The conclusions about the irrigation concepts and strategy were mixed, due to the short-term (1 season) nature of the project. No conclusions could be reached for the VAM inoculations because the study time was too short.

Jan 1, 1984

Despite limited discussion, Chemistry of Flotation is a good text and reference 1985 by M. C. Fuerstenau, J. D. Miller, and M. C. Kuhn Society of Mining Engineers Caller No. D Littleton, CO 80127 Softcover, $23.50 (member), $18.50 (student member), $28.50 (list) Review by Richard R. Klimpel Chemistry in Flotation, as stated by the authors, is intended as a textbook for students as well as a reference book for practicing flotation engineers. It covers subject matter related to surface phenomena; collectors and collector salts; natural floatability; the flotation of sulfide minerals, insoluble oxide and silicate minerals, semisoluble salts, and soluble salts; and slime coatings. There are no discussions in the book on practical plant implications of flotation chemistry, such as the influence of rate, particle size effects, dosage, flotation equipment, and methods of chemical addition. The book itself is small (only 177 pages), and, as published, is in an easy-to-handle soft cover. Once one accepts the intent of the authors, this book really does represent a very concise and convenient summary of the chemistry of flotation. It is, however, far from complete in its discussion of concepts and implications of data. Very often in the presentation, key prior knowledge (or at least subject matter awareness) not given in the book, is assumed. Thus, depending on one's familiarity with the specific subject matter, some sections can be easily followed while others could be tough going. Some of the discussion is so brief and terse on important subjects that unless the reader already realizes the meaning of the presentation, the conclusions to be drawn are not always clear. Therefore, if one is not expecting a self-contained primer on flotation chemistry, this book is very useful. To this end, the book is recommended to practitioners of flotation chemistry. The presentation of data in figures and tables is good. It helps considerably in the book achieving its conciseness. The authors certainly are qualified and knowledgeable in the subject matter - apparent in the style of presentation. In summary, this reviewer thoroughly enjoyed this book and will use it as a concise review of flotation chemistry. Richard R. Klimpel, member SME, is a scientist with Dow Chemical Co., Discovery Development, 1776 Building, M. E. Pruitt Research Center, Midland, MI 48640. International Symposium on Blast Furnace Ironmaking, 1985, The Indian Institute of Metals, The Tata Iron and Steel Co., Ltd., Jamshedpur 831007, India, 282 pp., papercover, no price given - Papers from this symposium held in Jamshedpur, India, include the following: determination of coal and coke quality; feed to blast furnaces; burden quality and blast furnace performance; operation of blast furnaces on charcoal; review of cast house slag granulation systems; developments in blast furnace engineering and control; process improvements in blast furnace ironmaking; coal injection into the blast furnace; and coke from stamp charged coal. Advances in Materials Technology for the Process Industries, 1985, edited by H.A. Huskins, National Association of Corrosion Engineers, P.O. Box 218340, Houston, TX 77218, 273 pp., softcover, $20-This book is the proceedings of a meeting held in Atlanta, GA in October 1984. It describes innovations in metallurgy, ceramics, glass, composites, and polymeric materials that impact the integrity and economics of operating systems. It covers biotechnical developments, improvements in membrane systems, or beneficiation processes, as well as developments in electrochemical controls, testing procedures, and surveillance techniques. A Reference Guide to Mining Legislation in Canada, 1985, by B. Barton, B. Roulston, and N. Strantz, The Canadian Institute of Resources Law, Room 430, Bio Sciences Building, The University of Calgary, Calgary, Alberta, Canada T2N 1N4, 120 pp., bound, $US28- This guide provides a ready means of finding how the different jurisdictions in Canada regulate mineral activity. It covers the rights required for exploration, development, and production of mineral metallics and industrial minerals. It does not cover placer mining, petroleum and natural gas, bituminuous sands, coal, or structural materials. Dictionary of Geological Terms, 1985, edited by Robert L. Bates and Julia A. Jackson, The American Geological Institute, 4220 King St., Alexandria, VA 22302, papercover, $7.95 plus $1 for postage - This third edition is for geoscience students, teachers, and rockhounds. It defines the core vocabulary of earth sciences, contains 8000 revised definitions, and includes 1000 new terms. It adds recent terms in plate tectonics, hydrology, and permafrost studies. Accurate definitions are given without technical jargon, cross-references are included, and commonly used abbreviations are provided. Processing and Utilization of High Sulfur Coals, 1985, edited by Yosry A. Attia, Elsevier Science Publishing Co. Inc., 52 Vanderbilt Ave., New York, NY 10017, 787 pp., bound, $142.50-These proceedings comprise the majority of the papers presented at the First International conference. Investigators there reported the latest discoveries, developments in commercial practice, and state-of-the-art reviews of scientific principles and applications of various technologies for handling, processing, and use of high sulfur coals. Sessions were held on: characterization of sulfur in coals; environmental problems and impact of high sulfur on coal use; selective mining and blending; coal desulfurization by physical and chemical cleaning techniques; handling of coal fines; sulfur capture during coal combustion; biological desulfurization of coal; and new applications for high sulfur coal. The Economics of Magnesium Metal, 1985, Roskill Information Services Ltd., 2 Clapham Road, London SW9 OJA England, 129 pp., 71 tables, appendices, bound, $750-Despite setbacks in some major magnesium markets in 1985, Roskill's latest forecast for the last half of this decade is for a 4% to 6% annual growth rate in demand. Growth for magnesium metal is expected in the motor industry for use as a possible substitute for aluminum. Some magnesium producers are altering their marketing strategies to cultivate this market. This study also includes a review of the worldwide magnesium industry, its end uses and consumption, and international trade and price trends.

Jan 7, 1986

By A. Lebedev

Application of dynamic simulation for a base metal processing plant is discussed. The plant receives ore of variable quality from two pits and blending had to be applied to maximise recovery. The plant employs multiple stage crushing, screening, dense media separation, two-stage milling, flotation and further filtration. Stockpiles and bunkers are used in the plant to cater for breakdowns and operating delays, the latter being appropriately incorporated in the model. A detail dynamic simulation model was constructed from the rock face to the filtration plant to assist the plant design, notably with definition of the ore blending method, sizing storage capacity and in-plant conveyors. The plant model was broken down to capital equipment items and various feed types and mass balances were tested to ensure that the production target is met. The dynamic simulation tested the proposed blending method, identified bottlenecks, produced risk profiles for all strategic storage facilities and overall helped minimise the project risks and improve confidence in the plant design. Keywords: Dynamic simulation, ore grade, blending, capacity, risk profile, throughput, utilisation

Jan 1, 2020

By C. M. Diaz, P. J. Mackey

Since its inception, in 1987, the Copper-Cobre series of conferences has established itself as the prime world forum for discussing advances in copper process metallurgy, in particular copper sulfide smelting, copper recovery by leaching and electrowinning and copper electrorefining. All copper producing countries have actively participated in the pyrometallurgy symposia held in the framework of these conferences. In 1999 and 2003, the close to 100 pyrometallurgy papers that were presented had to be accommodated in two volumes. In the present paper, the authors firstly provide a brief historical sketch of the Copper-Cobre conferences and then focus on providing a retrospective look at the dramatic changes that have taken place in copper smelting in the last few decades, primarily as discussed in the Copper-Cobre and precursor conferences pyrometallurgy proceedings. Topics include: the development of autogenous, increasingly more intensive, environmentally sound and energy efficient smelting processes; significant improvements in Peirce-Smith converting practice and at the same time the commercialization of alternative continuous converting routes; the consequent expansion and modernization of smelters; the increasing compliance with strict government environmental regulations in most copper producing regions of the world; the realignment of the copper smelting industry throughout the world; and trends in copper smelting R&D. A look at the future closes these reflections on the contribution of the Copper-Cobre conferences to the advancement of copper smelting technology.

Jan 1, 2007

By R. O. Neal, G. St. J. PERROIT

As natural gas is a waning resource in many places, increased interest has attached to the use of gas for the manufacture of carbon black. Because of a large number of requests for information on the subject, the Bureau of Mines has undertaken a detailed study of the carbon-black industry, covering the mechanical details of commercial methods, with the purpose of increasing the recovery of carbon black by such processes. A study has been undertaken of the economic factors governing the carbon-black industry, the uses and properties of carbon black, the dE)velopment of more Itccurate methods of testing carbon black, microscopic examination of different grades of black, physicochemical study of methods' of mQ.nufacture now in use, and research on new methods of manufacture. Part I of this paper covers the engineering and economic side of the industry; the other phases of the investigation which have been under the direction of G. St. J. Perrott, of the Pittsburgh station.of the United States Bureau of Mines, are discussed in Part II.

Jan 1, 1922

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

By G J. Delemontex, N J. Grigg

Pre-concentration of precious metal and base metal ore types is becoming more relevant with the discovery, development and operation of many lower grade deposits around the world. The fluctuations in metal prices expose many mines to risks especially dealing with low and variable ore grades.Pre-concentration, the process of concentrating the valuable metal into a smaller mass yield, effectively results in the introduction of higher feed grades to milling circuits. Gangue Rejection, the removal of lower S.G. waste rock from the circuit not only results in higher downstream grades but also potentially removes harder, non-valuable mineral, providing significant power savings within the circuit. The pre-concentration or ‘gangue rejection’ process offers a number of benefits when considering the treatment of marginal ore deposits, especially if it can be performed at a coarse crush size; these benefits include a reduction of the operating costs and the feed of more metal units to the mill.Gekko Systems has effectively utilized the Inline Pressure Jig (IPJ) to pre-concentrate the valuable metal, achieving high primary recoveries into a range of mass yields resulting in upgrade ratios between 2 and 10 times.This paper explores the benefits of pre-concentrating ‘marginal’ ore deposits prior to the milling circuit; the selective rejection of ore types that may affect either the recovery or comminution process, and also looks into the potential to effectively reduce the ‘cut-off’ grade when considering the mine planning process. Case studies of projects using the IPJ to pre-concentrate and reject gangue are also included.Pre-concentration and gangue rejection provide the potential to develop marginal ore deposits, thus providing higher grades, less gangue and more metal at a lower operating cost to producers.CITATION:Grigg, N J and Delemontex, G J, 2015. The pre-concentration of precious and base metal deposits using the Inline Pressure Jig – higher feed grades and more metal, in Proceedings MetPlant 2015, pp 296–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By Suresh K. Bhatt

This U.S. Bureau of Mines report reviews major developments in continuous haulage technology for underground coal mines. Haulage systems, both in use and under development, were investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, monorail bridge conveyor, multiple-unit continuous haulage, extensible, and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine research being conducted by the Bureau. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1991

By Nelson P. Hulst

COMMITTEES. DULUTH.-Nelson P. Hulst, Chairman; J. B. Adams, W. C. Agnew, M. H. Alworth, C. W. Andrews, R. Angst, William R. Appleby, C. E. Bailey, G. G. Barnum, E. F. Bradt, Mylie Bunnell, George L. Cheesebrough, Peter Christen¬sen, F. A. Cokefair, T. F. Cole, C. A. Congdon, N. Cowling, George H. Crosby, M. D. Cullum, C. d'Autremont, Jr., H. L. Dresser, C. T. Fairbairn. Walter Fitch, F. L. Gilbert, J. T. Hale, G. G. Hartley, E. B. Hawkins, M. S. Hawkins, J. H. Hearding, Louis Hill, L. J. Hopkins, F. E. House, J. C. Hunter, 0. D. Kinney, J. W. Kreitter, E. J. Longyear, Alexander McDougal, W. A. McGonagle, A. M. Marshall, W. N. Merriam, T. D. Merrill, John Millan, P. Mitchell, Clarence Moore, Hon. Page Morris, C. H. Munger, Henry Nolte, W. J. Olcott, A. L. Ordean, Thomas Owens, F. A. Patrick, H. M. Peyton; D. M. Philbin, Capt. Charles Potter (U. S. A.), L. W. Powell, Harry Roberts, Louis Rouchleau, George A. St. Clair, J. U. Sebenius, Joseph Sellwood, Amos Shepherd, W. B. Silvey, George Spencer, George C. Stone, H. B. Sturtevant, George D. Swift, Kirby Thomas, C. D. Thompson, A. D. Thomson, G. A. Tomlinson, Charles Trezona, R. R. Trezona, Maj. J. H. Upham, Charles Van Barneveld, W. W. Walker, J. L. Washburn, A. C. Weirs, H. J. Wessinger, A. B. Wolvin, Dwight E. Woodbridge. HOUGHTON.-W. E. Parnall, Chairman; W. D. Calverley, Secretary; W. B. Anderson, L. S. Austin, Jacob Baer, William Bath, F. J. Bawden., Simon Beahan, John Been, C. H. Benedict, Walter Bloomfield, S. H. Brady, Samuel Brady, Henry Brett, A. L. Burgan, F. I. Cairns, W. H. Cake, Arthur L. Carnahan, William Carpenter, Phillip Carroll, John J. Case, T. L. Chadbourne, W. A. Childs, B. F. Chynoweth, Captain James Chynoweth, H. P. Clausen, F. G. Coggin, H. D. Conant, J. B. Cooper, J. R. Cooper, John Cuddihy, Thomas Cummings, Robert Davidson, J. B. Dee, J. R. Dee, T. S. Dee, Theodore Dengler, M. M. Dennis, Captain Thomas Dennis,. F. W. Denton, A. D. Edwards, R. M. Edwards, C. S. Fales, Daniel Fisher, Henry Fisher, James Fisher, A. L. Floeter, Frank H. Getchell, M. C. Getchell, W. M. Gibson, W. M. Gilliland, James G. Glanville, George Goodale, H. S. Goodell, A. R. Gray, Edward Grierson, Homer Guck, H. D. Haddock, Captain Josiah Hall, John L. Harris, Captain S. B. Har¬ris, Enos Harrold, F. William Hartmann, George L. Heath, C. M. Hoar, Thomas Hoatson, 0. P. Hood, Captain Thomas Hooper, Captain Joshua D. Husking, Dr. L. L. Hubbard, Arno Jaelinig, E. D. Johnson, G. A. Koenig, Edward Koepel, C. H. Krause, R. H. Leach, A. W. Leonard, James MacNaughton, Edward McCormick, Thomas McDonald, R. T. McKeever, F. W. McNair, James McRae, John Mackey, John C. Mann, Major G. A. Marr, Captain Thomas Maslin, Harry Mercer, James Merton, Michael Messner, William F. Miller, Captain J. Milligan, Dr. J. W. Moore, Charles H. Moss, H. F. Nickerson, Charles L. Noetzel, P. H. Paine, John Penrose, Captain John Pentecost, Graham Pope, R. C. Pryor, James Ramsay, J. T. Reeder, Allen F. Rees, J. H. Rice, W. G. Rice, James

Jan 1, 1905

By Martín Antonio Encinas‐Romero, Patricia Guerrero‐Germán, Jesús Leobardo Valenzuela‐García, José R. Parga‐Torres, María A. Bracamontes‐Landavazo, Agustín Gómez‐Alvarez

A study was carried out to process a sulfide mineral concentrate from Norwest of Mexico containing 97 g/t Au, 0.15% Cu, and 15% Fe. An oxidative acid pretreatment was investigated using ferric sulfate as oxidant, followed by leaching of gold with sodium cyanide. Scanning electron microscopy, SEM-EDS, and X-ray diffraction, XRD, the analysis confirms the presence of quartz and pyrite species. First, a leaching was carried out without pretreatment, at ambient conditions, T = 25 °C and P = 1 atm, obtaining only a 45.2% gold extraction. Once the presence of Fe and Cu sulfides had been confirmed, the Eh-pH diagrams were constructed for the Fe-S-H2O and Cu-S-H2O systems, where it is appreciated that pyrite and chalcocite can dissolve with high oxidation potentials and forming sulfur, oxidizing to sulfate at highly acidic conditions. The oxidized concentrate was neutralized and adjusted to pH > 10.5; it was leached at ambient conditions, at different particle sizes, 44, 37, and 26.5μm, achieving an Au extraction of 75% using a concentration of 0.5% NaCN, 26.5μm particle size, 20% solids, and P = 1atm. Then the oxidized material was subjected to different temperatures, 25, 50, and 70 °C, under the same conditions and obtaining Au extractions up to 92% at 70°C. Additionally, the leaching process was compared using an autoclave reactor at moderate pressures, obtaining an increase in the extraction of Au up to 98% in 2 h, at T = 70 °C and P = 0.62 MPa.

Jan 23, 2022

By Alexander Siefert, Steffen Pankoke

In the development of commercial vehicles as well as of passenger cars, the effects of vehicle vibrations on operating safety, health and comfort can only be predicted by numerical simulation when appropriate occupant models are available. Such models must be based on human anatomy and have dynamic properties of real humans in order to achieve realistic results. Since human dynamic behavior depend on posture and percentile, the occupant model needs to be adjustable to these parameters with respect to geometry and dynamic properties [1,2]. Dynamic Human Finite-Element-Model CASIMIR CASIMIR is a non-linear, dynamic finite-element-model of the human body. It consists of a dynamic model of the upper torso with head, neck, shoulders and arms as well as of a dynamic model of the lower extremity with pelvis and legs. The most important part is the lumbar area with dynamic non-linear models of the lumbar spine and of back and abdominal musculature. The frequency-dependent characteristics of the intervertebral discs and the effects of muscle activation and non-linear frequency-dependent muscle properties are included. In the latest stage of development, CASIMIR has been equipped with a compliant model of the body surface in the contact areas to the seat. This results in a very realistic transmission of static and vibrational forces into the human body, see fig. 1. Intense model verification and validation has been performed in all stages of model development, starting with validation of small components like intervertebral disc, ending with validation of whole-body-vibrations using measurements of the dynamic mass / mechanical impedance [4]. For an in-detail examination of stresses in the vertebral bodies and discs, a non-linear submodel of the lumbar spine with an increased number of degrees of freedom can be coupled to the whole-body-model, enabling the researcher to examine local effects of vibrations and single shocks on the lumbar materials. [ ] Since it is well known that human dynamic behavior is significantly affected by anthropometric data and posture, CASIMIR can be individualized to the anthropometric status of single individuals or to the mean values for specific percentile groups. Furthermore, posture can be adjusted to the seating conditions applicable to a specific vehicle. Posture modification capabilities include the variation of the lumbar lordosis [3].

Jan 6, 2006

By R. C. Earlougher

Jan 1, 1970

By J Webster-Brown

The Tui Mine is an abandoned Pb-Zn mine giving rise to water quality problems in the Te Aroha region of Coromandel, New Zealand. When sampled in September 2002, for example, both the Tui and Tunakohoia Streams draining the mine site exceeded ANZECC (2000) water quality guidelines for aquatic life protection (Cu, Cd and Zn) and recreational quality (Cd). Based on trace metal mass flux (kg/yr) from parts of the mine site, the principal pathways by which Cu, Zn and Cd contamination reach these streams have been identified as:the tailings dam leachate,the diverted stream water from above the dam,the drainage from Adit 5 (which accounts for 95 % of Zn and Cd contamination in Tunakohoia Stream), andto a lesser extent, run-off from waste rock piles below Adit 4 level. Of the various remediation options, which have been proposed for the site, the following are identified as providing the best protection for the Tui and Tunakohoia streams:stabilising the tailings dam embankment and capping the embankment and tailings,constructing and/or cleaning out engineered diversion drains around the perimeter of the tailings dam to divert surface water away from the tailings dam, andinstalling bulkheads within Adit 5. A formal postal survey of the people of Te Aroha (66 respondents from 230 surveys) indicated that their priority was that the site be made safe for the public to visit, and used for recreation. As soil samples in potential recreational areas of the mine site, significantly exceeded guideline values for Cu, Pb, Zn, Cd and As, soil removal or capping clearly also needs to be part of a remediation plan. Development of the site as a historical/ecotourism area was viewed favourably, as this may encourage more visitors to the Te Aroha area as well as educate local residents.

Jan 1, 2003

By J. F. KENP

THE White Knob copper-deposits are situated about three miles south of Mackay, on the Salmon River .branch of the Oregon Short Line Railroad, in Custer county, Idaho. An outline-map of this district is given in Fig. 1. The deposits have been known and spasmodically worked for many years, and a total of over 3.5 miles of tunnels, shafts and other workings has been driven with a view to their development. These extensive excavations have exposed the deposits sufficiently to permit a careful geological examination. The peculiar features which give special interest to this paper are the branching, free-like form of the ore-bodies; the absence of zones of secondary enrichment in the partly oxidized pyritic deposits, and the fact that while the deposits are associated in a general way with the contact of an eruptive rock with limestone, which it penetrates, the garnetization has taken place not in the limestone, as is the usual case, but in the igneous

Mar 1, 1907

By D. Ksinsik, R. Boisvert, D. Leblanc

Casting, cooling and crushing/sieving of ferroalloys has followed a well-established pattern in the whole ferroalloys industry for many years. Usually liquid metal or alloys are cast into flat open moulds of various shapes and forms, and after solidification the product is removed from such mould to further cool down to a temperature where subsequent handling steps are feasible. Common to all mechanical product fractioning is the generation of dust and fine size material with lower product value. For almost 10 years, Bécancour Silicon has investigated alternative roads to improve technology and/or reduce or solve problems related to those disadvantages. Since 1995 Bécancour Silicon operates a special silicon granulation plant targeted to product for the chemical treatment/conversion of silicon for silicones production. Prior to the development of the granulation process, various systems had been evaluated, among others the vibrating casting bed, now in operation elsewhere but judged inappropriate because of the tapping volumes to be handled at Bécancour Silicon and other disadvantages. After evaluation of all aspects of heat transfer, radiation, and conductivity in relation to transfer media and within the product, a novel system was designed and built.

Jan 1, 2004

By M. Veiga

"Mining is an energy and water intensive activity. Increasing energy efficiency and reducing water consumption are two of the key requirements in moving toward a more sustainable mining industry. Water reduction, reuse and recycle options are reviewed, identifying cases where these options have been implemented. Then a novel mine water network design method is described, which analyzes a mine/mill water system in order to identify areas where water requirements and water system energy requirements can be reduced. First, a site water balance is determined and major water consumers and sources are specified. Next, multiple possible combinations of supplying water to mine and mill consumers are compared. Finally, low energy and water combinations are identified.INTRODUCTIONMining consumes vast quantities of energy: The whole mining and metals sector consumes over 12% of the world’s energy (DOE, 2009). Mining also requires large quantities of water, although mining water consumption is a relatively small portion of the overall world water use. Even in relatively dry, mining-intensive countries like Australia and South Africa, mine water consumption is only 2-3% of national water demand (Brown, 2003). However, at the local level, when mining takes place in areas where water is scarce, mine water consumption can severely impact local supplies. In addition, acid rock drainage, leaks from waste impoundments, or direct disposal of tailing into waterways can contaminate surface and groundwater (MMSD, 2002). Mine water systems can be large energy consumers, but better mine water systems can reduce both water and energy consumption. Improving water system design and practice are key strategic requirements in moving toward a more sustainable mining industry.This paper addresses conventional base-metal or precious-metal mine sites, which consist of an underground or open pit mine and a mineral processing plant, or mill. Ore is extracted and processed through the plant to produce a saleable product. Tailing, or waste material, is then deposited in a tailing storage facility (TSF). Any rock removed from the mine with no economic value, or waste rock, is stored without being processed."

Jan 1, 2010

By Robert H. Peters

This report presents a literature review conducted by the U.S. Bureau of Mines. The review summarizes what has been learned from the large volume of empirical studies on the effectiveness of eight types of interventions intended to increase organizational effectiveness via in the management of human resources. The interventions concern the following: recruitment, selection, training, objective feedback, goal setting, reward systems, participative management practices and organization development. Although many of these interventions appear to have the potential for improving the safety and efficiency of mining operations, it does not appear that they are being widely used. Examples are given of the successful use of a few of these interventions at mining operations. An analysis of the relationship between coal mine productivity and safety is also presented. This analysis generally supports the view that good safety performance and high productivity are NOT incompatible goals. In fact, safe mines also tend to be more productive and vice versa.

Jan 1, 1992