Search Documents

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

By K. Thirumalai

The feasibility of breaking hard rock by thermal weakening and subsequent mechanical impacting was tested, Field tests at a basalt quarry in Dresser, Wis., demonstrated that large hard-rock blocks (5 by 5 by 5 ft) could be effectively reduced in size by this method. A series of secondary breakage tests, using air-propane heating, resulted in an average heating cost of $0.36 per ton. This combination energy approach provides an alternate means of size reduction of large hard-rock boulders for quarry and for underground are chute and grizzly operations where mechanical methods, used alone, are ineffective.

Jan 1, 1975

By H Thanasekaran, L Christodoulou, J Kohmuench

"Column flotation has been successfully applied to iron ore concentration since the 1980s with the goal of reducing silica content and allowing for the efficient production of pellet feed. Since then, columns have been widely used in iron ore processing due to: their lower capital and operational costs when compared to conventional cells their ability to generate higher concentrate grades and recoveries.Currently, more than 100 columns have been installed within Brazilian iron ore processing circuits for rougher, cleaner and scavenger duties. Despite it being a well-established approach, several technological advances have improved column design, accessories and performance. This work presents the performance of some iron ore columns in Brazil and the recent technological developments.CITATION:Thanasekaran, H, Kohmuench, J and Christodoulou, L, 2013. Column flotation of iron ore - status and advances, in Proceedings Iron Ore 2013, pp 479-484 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By Matthew E. MacGregor, Hugh T. Kelly

I.H. 635 (LBJ Freeway) was constructed as a loop freeway around the city of Dallas in the late 1960s and early 1970s with a design capacity of 160,000 vehicles per day (vpd). Today’s facility is carrying over 270,000 vpd. To help mitigate community concerns with regard to right-of-way issues, noise, safety, and traffic disruption, the Texas Department of Transportation (TxDOT) is planning a number of significant improvements. The West Section improvements include the construction of managed HOV/Toll lanes. Within this 8-mile section, TxDOT is planning two mined tunnels(1.5 and 1.9 miles long) beneath the LBJ Freeway. The mined tunnels will connect to cut-and-cover box sections in both the east and west directions. This paper presents an overview of the project development from the design schematic, through the geotechnical investigations, into the current design stage. The project is being planned for implementation by use of a Comprehensive Development Agreement.

Jan 1, 2005

By Axel Preusse

Mining subsidence plays an increasing important role in the Chinese hard coal mining. Reasons for this are a substantial rise of production during the last decade, a dense settlement in many mining regions, the increasing emergence of private residential property as well as a grown environmental awareness. German companies and research institutions hold an over more than 150 years existing know-how in all subjects of mining subsidence engineering. Due to partially comparable preconditions regarding mining depth, mining methods and geological conditions, a close co-operation between German and Chinese mining subsidence engineering experts has been in existence for some years. This German-chinese co-operation is introduced in this paper.

Jan 1, 2007

By Mark A. Williams

Topography and geology greatly impact the decision of how to plan and operate a surface mine. To extract coal, five primary surface mrning methods are practiced in the United States. These include contour strip. mountamtop removal, area, modified area, and open pit mining methods. The first four approaches are commonly associated with coal mining while open pit techniques, although used in the mining of coal, are more commonly applied to the mining of hard rock, metals, and aggregates. Various sub-routines of the primary surface mining methods are likewrse applied rn the industry.

Jan 1, 1991

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

By Xi Zhang

A technique for fabricating free-standing, high-aspect-ratio porous and pillar-type Ni structures has been developed using wet Si processing. A wafer of (100) Si was initially etched in HF solution to form deep pores with micron-sized diameter. The aspect ratio can exceed 200. By introducing the as-etched Si into a defined aqueous Ni2+ solution, Ni deposits grew rapidly onto the sidewalls and replaced the Si. Long-time immersion allows the Si sidewalls to be completely converted and thus form a metallic Ni structure with high-aspect-ratio pores. It is known that close-packed submicron Si pillars can be formed by oxidizing and subsequent etching of the macropore sidewalls. Treated in the same Ni solution, high-aspect-ratio Ni pillars were correspondingly emerged by replicating the original pillar-type Si structure.

Jan 1, 2006

By A C. Edwards

The Mongol-Okhotsk belt consists of detached fragments of the Circum Pacific fold belt which have been trapped within the Mongol-Okhotsk fold belt. In its western part, the structures of the belt form an east-facing loop that is not connected with the other orogenic structures of Central Asia. In the eastern part of the belt (the Mongol-Okhotsk suture zone) the terranes form a zone between the Siberian craton to the north and the Bureya composite terrane to the south, that is linked with the Circum Pacific belt. The accretionary terranes, together with their Precambrian backstops, form a series of consistently-stacked, paired units that are bounded by northwest and north trending sinistral strike-slip faults. The ages of the rocks forming these accretionary complexes vary from Late Precambrian - Carboniferous in the west to Cambrian - Jurassic in the east. The terranes developed due to a progressive westward stacking of the accretionary complexes during the process of accretionary growth. The magmatic rocks young eastward indicating that migration of the magmatic front of the arc followed the eastward growth of the accretionary complexes. The accretionary terranes may be differentiated by their Paleozoic lithological assemblages. Only the Selemdzha, Niman, and Kerbi terranes located in the eastern part of the Mongol-Okhotsk suture zone contain significant amounts of black shale, and it is these terranes that host the bulk of the hardrock and placer gold mineralisation that is present within the suture zone. Gold mineralisation is present both as vein style and disseminated mineralisation within structural duplexes.

Jan 1, 1999

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

By E. C. Westman

Three-dimensional velocity tomograms were generated on a daily basis to image mining-induced changes to the overburden above a longwall mine. The hypothesis was that a coherent redistribution of seismic velocity, due to the development of high-stress zones, could be imaged at the mine scale. Seam depth was 360 m and source location depth varied from 100 to 1000 m. Sixteen geophones were distributed over a 600 by 600 m square area on the surface above the mine. More than 12,500 events were recorded over an 18 day period. The recorded seismicity provided input for the local-earthquake tomography code, SIMULPS. Eighteen tomograms were generated and high-velocity regions correlated well with high abutment stresses. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated. These results indicate that velocity tomography can be used to provide a better understanding of temporal changes within a rock mass, and can potentially be used to produce a better understanding of the mechanisms that lead to unanticipated ground failures.

Jan 1, 2008

By Ferdinand Roehlich

An evaluation of the use of manually activated, installed,. dry chemical fire protection systems on underground metal and nonmetal mine vehicles is described. In addition, an assessment of the possible health risks posed by the dry chemical extinguishing agents used in such systems is provided. Work involved installation of fire protection hardware on an operating piece of underground metal/nonmetal mine equipment and, via actual fire tests, a determination of the effectiveness of the hardware in extinguishing on-vehicle fires. Two fire protection systems were installed on a Caterpillar 988 front-end loader in St. Joe Mineral's Fletcher mine, near Viburnum, Mo. Both a fully pressurized Safety First CM-20 and a nonpressurized cartridge actuated Ansul A-101 were installed for comparative purposes. Both systems operated satisfactorily during an 8-month endurance trial period which preceded the actual fire tests. Each system was able to extinguish an 18" x 4" class B test fire placed in the engine area of the machine. The health hazards analysis of dry chemical powder consisted of a detailed search of published literature relating to these multipurpose agents. This data was verified via a controlled laboratory analysis of two monoammonium phosphate based powders (Safety First Unikem and Ansul Forey) and an analysis of air samples collected at various locations on the test vehicle during the fire tests. Although the powder was found to be nontoxic, two potentially dangerous thermal decomposition products were identified--ammonia and phosphoric acid. However, later analysis indicated that an operator would not be exposed to dangerous concentrations of either compound if he were to remain outside of the powder cloud. A "Selection and Use Manual for Manually Activated, Fixed Fire Suppression Systems on Underground Metal and Nonmetal Mining Equipment" was prepared both as an, appendix to the report and for distribution under separate cover.

Jan 1, 1977

The contract for the Water Jet Chock Mounted Miner Feasibility Study was awarded to FMC Corporation's Advanced Products Division on 18 November, 1974. The program was divided into four phases as follows: ? Phase I - Planning ? Phase II - Conceptual Design ? Phase III - Budgetary Cost Estimate and Economic Feasibility Study ? Phase IV - Final Report During Phase I, which lasted 1 month, most of the necessary information and data for the conduct of Phase II was obtained. To accomplish this, arrangements were made for personal visits to the University of Missouri at Rolla, Illinois Institute of Technology Research Institute, USBM TCMRC, Alpine Equipment Co., Mining Progress, Inc. and Eastern Associated Coal Corporation's Harris No. 1 Mine. Also, a list of manufacturers of high pressure equipment was compiled to be contacted during Phase II. Finally, the objectives to be accomplished during Phase II were outlined. The Phase I Report was submitted on 23 December, 1974. At the beginning of Phase II, personal visits were made to the research centers and firms mentioned above. Later an additional visit was made to the Harris Mine, and to the Pittsburgh Mining Research Center at Brucetun to observe a test of a water jet mounted on an Alpine Mining Machine. Equipment manufacturers of high pressure components such as hoses, tubing, valves, pumps, and intensifiers were contacted to obtain item performance data, availability, and cost.

Jan 1, 1975

This paper considers the application of recent laboratory gas sorption data to the understanding outburst phenomena in underground coal mining. Previous use of threshold limits based on gas content and coal rank are placed in perspective. Although this work focuses on overseas research and experience, parallels can be drawn for New Zealand coal settings, taking into account localised mining and geological factors.

Jan 1, 1994

By J. L. van Niekerk

The research project reported on represents the first comprehensive attempt to measure the vibration levels of a variety of tools and equipment in the South African mining industry to determine the effect thereof on the health of workers and operators. Although human vibration has been studied extensively internationally only one reference pertaining to the South African mining industry could be found. From studies conducted in Canada and elsewhere it was evident that rock drills do have potentially hazardous levels of vibration. The scope of the research included measurements on a broad spectrum of tools, machines and vehicles used in the South African mining industry. Both hand-arm vibration, where the majority of the vibration enter the body through the hands, and whole body vibration, where the whole body is exposed to vibration through contact by the buttocks or feet, were investigated and measured. More than 700 sets of vibration data measured on 70 machines at 15 mines and workshops were obtained. Data were obtained for at least 24 different types of equipment and machines that were previously judged to have medium to high levels of vibration. All measurements were conducted in accordance with the international standards: ISO 5349, on hand-arm vibration, and ISO 2631-1, for whole body vibration. The equipment with the highest vibration levels in the hand-arm category was: rock drills, both pneumatic and hydraulic; pavement breakers and jackhammers; hand-held compactors; pneumatic wrenches and electrical hammer drills. Of these the rock drills had weighted vibration levels in excess of 20 m/s2. As far as whole body vibration was concerned the highest values were measured on earth-moving equipment. The major conclusion from this study is that the measured vibration levels are sufficiently high to create an enhanced level of risk of vibration-induced disorders in a significant proportion of the operators of hand-held equipment. The most notable examples are hand-held rock drills, pavement breakers, jackhammers and certain selected workshop tools. The results of the study indicate that a comprehensive epidemiological study should be undertaken on present and past workers to determine the prevalence of vibration-induced disorders.

Jan 1, 2000

By I. Liebman

The Bureau of Mines conducted research to develop triggered barrier systems for protection against gas explosions that can occur in underground coal mines during the use of continuous miners. Several extinguishing agents were tested in barriers at a simulated mine face. Water, powered by pressurized nitrogen, was found to be efficient in stopping fully developed gas explosions, but it had little effect against the explosion during its incipient stage. Hybrid combinations of currently known extinguishants, however, were successful against incipient explosions. Three hybrids that were developed and tested consisted of Halon 1301, combined with either an aqueous foam solution, water, or a dry chemical powder. The three hybrids were found to be more efficient than any constituent alone. Results of the tests point to a synergism between the hybrid components, and indicate that the Halon aids in dispersing its constituent and also converts the aqueous foam solution into a stable fine foam and the water into fine drops.

Jan 1, 1978

By L. Douglas Smoot

This research program was a theoretical and experimental study to improve understanding of the mechanisms of flame extinguishment in methane-coal dust-air-suppressant mixtures. This final report is a summary of work conducted during this grant, sponsored by the Bureau of Mines. Work under this new grant closely followed a recently completed contract for the Bureau of Mines that was conducted at this laboratory, and results of the earlier contract are also summarized in this report, as required in the grant work statement. The experimental effort was concentrated on supplementing the limited data available to describe laminar flames in methane-coal-air-suppressant mixtures. The theoretical effort was devoted to developing a comprehensive model that could be used to explain and extrapolate the experimental data. Selected for study were the following flames: Methane-air; methane-air plus KHCO , KNO3, K C204, KBr, Al203 or Monnex; methane-coal dust-air; coal dust-air with size, volatiles content, and concentration as variables, and coal dust-air plus KHCO3, KN03, KBr, NaCl or CaC03.

Jan 1, 1978

By J. F. Lupo

Heap and valley leach operations rely on solution collection piping placed within the heap to enhance both solution recovery and to assist overall solution management. The most common piping used in leaching operations is solid or perforated High Density Polyethylene (HDPE) pipe and Corrugated Polyethylene pipe (CPE). These pipes are widely used because of their low cost, ease of installation, durability, and flexibility. The typical recommended maximum design depth of burial for HDPE and CPE pipes is on the order of 30 meters (100 feet). However, ore heap heights at many facilities exceed 30 meters and some are now approaching 180 meters (600 feet) in height. At very high ore heap heights, the stability and performance of HDPE and CPE pipes becomes a critical issue for leaching facility design and operation. Failure of solution collection piping can lead to poor solution recovery, high hydraulic heads on the liner system, and in some cases, unstable ore slopes due to high solution pressures near slopes. This paper presents a review of methods that have traditionally been used to evaluate pipe stability under high normal loads. A common shortcoming of these methods is the inability to account for beneficial effects of ore arching around pipes and the time-dependent creep (stress relief) behavior of polyethylene (PE) materials. A new analytical approach is developed and presented which includes the effects of ore arching around pipes and creep of PE materials. The results of the new approach show that PE pipes will deform under high heap loads, but can remain stable and functional. Pipe stability is shown to be dependent on the type of pipe backfill and initial backfill compaction. The new approach represents a useful tool for designing applications for PE pipe under high normal loads.

Jan 1, 2001

By William Gleason

The Society for Mining Metallurgy and Exploration (SME) has a long and proud history of being the world?s leading resource for the dissemination for technical information regarding the fields of mining and mineral extraction and processing. That reputation was met, and maybe even exceeded, with the programming for the Society?s 2014 Annual Meeting in Salt Lake City, UT Feb. 23-26. The meeting drew more than 6,700 attendees to the three-day conference that featured more than 90 technical sessions with 670 presentations. These sessions covered the breadth of the mining and minerals industry, but it was the so-called ?softer issues? that were discussed in the keynote session that kicked off the meeting. The keynote session, ?Community Engagement: Building Partnerships for Mining,? brought together some of the leading voices from the mining industry, as well as some of the top voices from nongovernmental organizations (NGOs) that work in the mining sector. The common ground between the panelists was their dedication to working to ensure a social, economic and environmental balance in the development of mines. ?We wanted to bring these NGOs in to begin a dialogue to see how we can work together,? said SME President Jessica Kogel. ?This is a space that SME has not typically operated in, but one in which SME can bring a technical, scientific voice to the discussion. SME wants to play a leadership role in creating partnerships between the technical, social and economic areas that are crucial to the success of any mining project.? In today?s environment, finding mineral deposits and extracting the minerals in an economically viable manner is just one piece of an increasingly complex puzzle. Earning and maintaining a social license to operate requires careful consideration of local and global impacts. The industry often comes under intense scrutiny when a new project is proposed and, therefore, it must strive to meet the highest ethical and environmental standards. Success requires cooperation and collaboration between the industry, community and NGOs.