Search Documents

By Jack L. Taylor

WITH the exception of the work of Vogel,&apos; and Rolla and Iandelli, very little information has appeared in the literature on titanium binary systems with the rare earth elements. Rare-earth additions to titanium alloys may possibly parallel the beneficial effects on the physical properties of certain steels. Having this in mind, some knowledge of solubility limits and intermediate phases, if any, would be useful. An investigation of the titanium-rich Ti-Ce system was started. Alloy Preparation The iodide titanium from the New Jersey Zinc Co. and the cerium metal from the Institute for Atomic Research Ames Laboratory used in this work were supplied with the typical analysis shown —iodide titanium: 0.0065 pct Mn, 0.0022 pct Fe, 0.0015 pct Cu, and 0.0042 pct Pb; cerium metal: <0.01 pct Fe, <0.03 pct Si, <0.05 pct Ta, <0.02 pct Pr, <0.03 pct Ca, <0.02 pct Mg, with no trace of Nd, La, or Th. The cerium metal, stored in oil, was washed and scraped just before weighing into capped cups machined from iodide titanium. The cold hearth helium-arc furnace described by Schramm et al3 was used for melting. The alloy buttons from the arc-melted cup were cut in two, mounted, and examined. Homogeneous alloys were demounted and rolled to approximately 1/4-in.sq bars. Sections l/8 in. thick were cut from the bar to provide samples. The Ti-Ce alloy buttons analyzed for cerium were of the following composition: 0.19, 0.36, 0.48, 0.61, 1.15, 2.52, 3.06, 3.70, 4.30, 9.20, 14.26, and 18.50 wt pct. Nominal

Jan 1, 1958

By Rodolfo Espinosa

"Industrias Peñoles, S.A. de C.V. in Mexico, has nine mining operations, six managed by Peñoles (base metal mines) and three managed by Fresnillo plc (precious metal mines). Seven of the operations use flotation and the other two are heap leach operations, one for gold and the other one for copper.This paper gives a brief introduction of Peñoles, shows mine locations and describes the main process characteristics of each concentrator. It also presents four of the new operating practices that were implemented over the last four years to improve the economics of the mining operations. These include (1) the use of centrifugal gravity concentrators to increase the recovery of gravity recoverable gold (GRG) and silver (GRS), (2) the use of expert systems to reduce process variability while increasing grades and recoveries, (3) the application of the Six Sigma methodology to key projects to ensure success and personnel development and (4) the use of water chemistry fundamentals to identify chemistry problems and design adequate solutions for improving grades and recoveries.INTRODUCTIONPeñoles was founded in 1887. It is a mining group with integrated smelting, refining and chemicals producing operations. Peñoles is the world largest producer of refined silver and metallic bismuth, the leading Latin American producer of refined gold and lead. It is amongst the world leading producers of refined zinc and sodium sulfate.Peñoles operates and controls six underground mines in Mexico and is the largest producer of zinc and lead of the country. It also produces copper concentrates and cathodes. Through its 77.1% equity stake in Fresnillo plc (a London Stock Exchange listed company); Peñoles is also a significant producer of gold and silver. Fresnillo plc operates three precious metal mines in Mexico. While Fresnillo is the world largest primary silver mine, Ciénega and Herradura are two leading gold mines of Mexico. Figure 1 shows a map of Mexico indicating the locations of the Peñoles mines. The main process characteristics of each concentrator are listed in Table 1."

Jan 1, 2011

By Philip Weaver

The MIDAS project is funded by the European Commission (DG Research) and began on the 1st November 2013. The project will investigate the environmental impact of deep-sea mineral and energy extraction: specifically, polymetallic sulphides, manganese nodules, cobalt-rich ferromanganese crusts and the potential mining of rare earth elements. As deep-sea mining becomes ever closer, and the International Seabed Authority begins to develop its regulatory framework for exploitation of deep-sea minerals, MIDAS is well timed to provide fundamental scientific information. The MIDAS partnership represents a unique combination of scientists, industry, social scientists, legal experts, nongovernmental organisations and small and medium enterprises. MIDAS is carrying out research into the nature and scales of the potential impacts of mining including 1) physical disturbance of the seabed by mining, the creation of mine tailings; 2) the potential effects of particle-laden plumes in the water column, and 3) the possible toxic chemicals that might be released by the mining process. Key biological unknowns, such as connectivity between populations, impacts of the loss of biological diversity on ecosystem functioning, and how quickly the ecosystems will recover will all be addressed. The plan is to use this information to aid development of recommendations for best practice in the mining industry. A key component is the involvement of industry within the project and through stakeholder engagements to find feasible solutions. The project will work closely with European and international regulatory organisations to take these recommendations forward into legislation. A major element of MIDAS will be to develop methods and technologies for 1) preparing baseline assessments of biodiversity, and 2) monitoring activities remotely in the deep sea during and after exploitation, including ecosystem recovery. To carry out this work MIDAS is conducting a number of research cruises to examine the above issues at potential sites for exploitation of SMS and nodule deposits. This talk will present some of the recent findings of the project.

Sep 1, 2014

By Andrew A. A, Hamilton P. J

Constraints on pore water evolution in the aquifers of a sedimentary basin may be realised through stable isotope analyses of present day waters, and their comparison with water compositions calculated to have been in isotope equilibrium with the products of diagenesis during burial. Integrated with detailed petrographic observations, and thermal, structural and stratigraphic analyses, fluid migration patterns at various stages in a basin&apos;s history can be identified. This has important implications for modelling basin hydrology, hydrocarbon distribution, and reservoir quality in the Latrobe Group, Gippsland Basin, and oil-prone successions Elsewhere.

Jan 1, 1992

By Oliver Bowles

In its geologic sense the term marble is applied to rocks consisting of crystallized grains of calcite or dolomite or a mixture of the two. Although limestone has the same chemical composition as marble it differs in that the component particles of calcium or magnesium car- bonates are granular and noncrystalline. In marble the crystals may be intimately intergrown, whereas limestone is an aggregation of unrelated particles cemented together into a solid mass. In its commercial sense the term marble has a much wider applica- tion. As susceptibility to polish is one of its chief commercial assets, all calcareous rocks capable of polish are classed as marbles. Lime- stones that show little crystalline structure may, if they take a good polish, be classed as marbles. Furthermore, serpentine rocks, even if they contain little calcium or magnesium carbonate, are classed as marbles, as they are commercial substitutes of true marbles.

Jan 1, 1916

By K. Hasselwander, K. Knabel

"A significant area of Outotec’s business involves fluidized bed roasting. With several decades of experience, more than 300 reference plants and strong R&D capabilities, the company provides several industries with optimum processing solutions. Applications include oxidation and sulfation of sulfides found in copper, pyrite and zinc concentrates. Gold production and de-arsenifying roasting are also within this scope. This paper describes the latest furnace developments and includes novel trends. Moreover, hot and wet gas cleaning systems are examined focusing on unit operations related to the removal of components such as dust, SO2 for sulfuric acid production, fumes, halides, Hg, hydrocarbons, nitrous oxides and metals.INTRODUCTIONGenerally, when defining roasting processes, it can be stated that the respective primary pyrometallurgical reaction is exothermic, of gas-solid nature and relates to a value solid product. These processes are a key focus within Outotec’s scope and include: (i) dead roasting (ii) sulfating roasting (iii) partial de-arsenifying roasting and (iv) two-stage, de-arsenifying roasting.Dead roasting involves the oxidation of a given sulfide, thus allowing for a subsequent leaching process, and has been applied to producing ZnO. Dead roasting of pyrite has also been extensively utilized with a primary goal of producing sulfuric acid. In contrast, sulfating roasting involves converting a sulfide to its sulfate, enabling a selective sulfation of components, such as Cu or Co, and their separation from ferrous components during leaching (produced sulfates are soluble). Partial roasting involves partially oxidating the metal sulfide to its oxide with the simultaneous production of gaseous As4O6, which is handled during gas cleaning. The solid product, containing hardly any As, is rich in S and can be fed to a respective smelter (e.g. in the case of Cu). Alternatively, if the production of oxide is required, a dead roasting step is added after the partial roasting step, with the overall process considered as two-stage roasting."

Jan 1, 2012

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By Antoni Kalukiewicz

From 1997 through 2000, a team of Polish experts headed by the author studied the prospects of mining newly discovered emerald deposits in Afghanistan. This article describes the scheme for mechanization of the mining operations, along with improvements made to the ventilation facilities and lighting. The required equipment was flown to Afghanistan and the Afghan miners were trained in machine operation and maintenance.

Jan 1, 2005

By Cathy Aimone-Martin, Robert Brentar, Brent Meins, James Lauer

Vibration measurements of multi-story structures in an urban environment began 3 years ago in New York City during close-in blasting to adopt correct measurement procedures and recommend revised ground vibration limits that best characterize cracking potential in mid- to high-rise structures. Two broad categories of structures included non-engineered 4- to 6-story multi-family unreinforced brick masonry buildings, built from the late 1800s to around 1930, and post-WWII, high-rise structures of reinforced concrete and steel rising 12 to 40 stories. In-ground vibration limits similar to those recommended by the U.S. Bureau of Mines safe criteria, developed for 1- and 2-story residential structures, are imposed by the New York City Fire Code. However, these limits are often lowered by project engineers or New York Department of Buildings when blasting is planned near buildings designated Landmark or historic and classified as fragile or vibration-sensitive. Seismograph measurements to determine compliance with in-ground velocity limits currently employ geophones mounted to basement walls and on concrete slabs overlying rock. These measurements cannot be correlated with upper structure cracking potential and are often exceeded, resulting in excessive and costly downtime to allow post-blast damage investigations.

Jan 1, 2014

By B. W. Dunning

This paper describes studies conducted by the Bureau of Mines to achieve its goal of developing methods for increased recovery and utilization of valuable constituents in a wide variety of domestic and industrial wastes, In this particular study, 36 units of obsolete electronic equipment from military aircraft were disassembled into their modular components by hand to determine materials distribution. Further modular disassembly into individual parts was used to identify metal composition. After identifying the metals in some of the more difficult to dismantle modules, similar modules were grouped together, shredded, mechanically separated, and using metal composition data from hand separation, classified along with the hand-separated materials. Although this equipment is normally classified as law-value iron-bearing aluminum, data were obtained that indicated the potential for moderately higher value classification. The electronic units were classified as to precious metals, copper, iron, and aluminum contents, and scrap values were estimated.

Jan 1, 1980

By I. Ocak

The modulus of elasticity of rock material (Ei) is an important rock property that is used as an input parameter in the design stage of engineering projects such as dam and tunnel constructions, mining excavations, and so forth. However, determination of the modulus of elasticity is sometimes difficult to obtain by laboratory tests because high-quality cores are required. For this reason, empirical methods for predicting the modulus of elasticity of rock material have been popular research topics in recently published literature. In this study, the relationships between the uniaxial compressive strength (UCS), unit weight (?) and modulus of elasticity for different types of rocks were analysed by using 177 data obtained from laboratory tests carried out on cores obtained from drill holes within the area of the Kadiköy-Kartal Metro line (Istanbul, Turkey). Keywords: Kadikoy?Kartal Metro, uniaxial compressive strength, unit weight, estimating the modulus of elasticity.

Jan 1, 2008

By Mark DeSalvatore

Currently, at Caltrans, the Office of Structure Design is carrying out an extensive seismic retrofit program involving transportation structures throughout California. The goal of the retrofit program has been to upgrade existing transportation structures to meet the present seismic codes and anticipated loads that are generated during a seismic event Part of the retrofit program involves retrofitting existing structure foundations when required. To determine if the foundations of a specific structure need to be retrofitted, an engineering analysis of the existing foundations has to be done. If the engineering analysis of the structure foundations determines that the foundations will not meet the load carrying demands required by the structural engineer, the existing foundations are then retrofitted. The retrofit projects that require foundation modifications can be separated into two general cases. The first case comprises structures where the original designs will not meet the demands of the present seismic design code. In this case, the existing foundations are not capable of providing the load capacities the current seismic code requires. The second case consists of structures where the retrofitting of the superstructure will increase the required load carrying capacity of the existing foundations during a seismic event In this case, the anticipated load demands on the existing foundations are greater than the foundations are capable of providing. For either of the cases listed above, the present strategy for increasing the capacity of the existing structure foundation consists of installing tiedown anchors or large capacity piles to provide the required resistance to seisraically induced loads.

Jan 1, 1993

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of "ore. accurate detonators. The new and "ore accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1989

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By H. P. Greenwald

Cooperation between the Bureau of Mines of the United States Department of the Interior and the Safety in Mines Research Board of Great Britain dates from 1924. It has been intimate and has involved exchange of personnel and. equipment as well as information. Correlation of divergent results obtained in large-scale tests of the explosibility3/ of coal dusts made in the respective countries was one of the first problems to be studied. The purpose of this paper is to show to what extent such correlation has been achieved. COMPARISON OF TEST METHODS The first research accomplished Jointly by the two organizations was a comparison of large-scale methods of determining the explosibility of coal dust. Large samples of coal were exchanged and subjected to test in the Bureau&apos;s Experimental coal mine and in the Board&apos;s steel gallery, 38 inches

Jan 1, 1939

By H. P. Greenwald

Cooperation between the Bureau of Mines of the United States Department of the Interior and the Safety in Mines Research Board of Great Britain dates from 1924. It has been intimate and has involved exchange of personnel and. equipment as well as information. Correlation of divergent results obtained in large-scale tests of the explosibility3/ of coal dusts made in the respective countries was one of the first problems to be studied. The purpose of this paper is to show to what extent such correlation has been achieved. COMPARISON OF TEST METHODS The first research accomplished Jointly by the two organizations was a comparison of large-scale methods of determining the explosibility of coal dust. Large samples of coal were exchanged and subjected to test in the Bureau&apos;s Experimental coal mine and in the Board&apos;s steel gallery, 38 inches

Jan 1, 1939

By B E. De Gee, N Viviers, A Naidoo

In 2013 the Mopani Copper Mine Mufulira plant in Zambia embarked on a project that was aimed at improving concentrator recoveries. The project commenced with the automation of the milling and flotation circuits. This involved the installation of new instrumentation, namely measurement devices and actuators, and the connection of these to new programmable logic controllers (PLCs).The infrastructure changes were followed by the implementation of basic proportional-integral-derivative (PID) controllers on the PLCs. Supervisory control and data acquisition (SCADA) interfaces were also implemented to allow for switching between controller modes, inputting of setpoint variables and to provide a visual display for process monitoring. The final phase of the project involved the installation and commissioning of advanced process control (APC) solutions on the milling and flotation circuits. This work was carried out by Mintek over 21 on-site days. The APC solutions included the MillStar and FloatStar suites of advanced controllers.The MillStar control suite focused on stabilising the mill feed and mill discharge on the two primary mills as well as the flotation circuit feed. Mintek’s CyLas instruments, which provide a measurement of the hydrocyclone underflow angle, were also installed. The measurements were incorporated into the discharge stabilisation control on both milling circuits. The FloatStar level stabiliser controller provided flotation cell pulp level control on fourteen cells, including two columns.Performance tests showed that the Mintek APC system stabilised the mill feed and mill discharge while ensuring the process remained within operational constraints. The MillStar control system utilised the CyLas instrument to prevent roping on the hydrocyclone underflow. This was not always achieved under normal operation. Additionally, the flotation section was stabilised as a result of improved level control by the FloatStar control system.Performance comparisons showed that the Mintek control system improved the operation of the milling and flotation circuits resulting in a greater copper recovery.CITATION:Naidoo, A, De Gee, B E and Viviers, N, 2014. Implementation of an advanced milling and flotation control system at Mopani Mufulira copper mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Nasser Madani, Yerbol Tussupbekov, Sergei Sabanov, Zarina Mukhamedyarova

A case study was conducted on a metal mine operating in Kazakhstan, in which problems were associated with use of a complicated and outdated ventilation system and its high expenses. The mine needs to reconsider its existing ventilation system and identify the risks associated with operational losses when using this ventilation system. The aim of this study was to develop an efficient risk analysis method capable of estimating operational risks and financial benefits of the existing mine ventilation system. The developed risk analysismethod considers ventilationmodelling, riskmodelling, and financialmodelling.Ventilation modelling comprises ventilation simulation and ventilation financial simulation. In risk modelling, the number of risk events occurring with the use of existing ventilation system and the operational losses during these events is estimated. Financial modelling considers operational losses and ventilation financial simulation benefits and uses a dynamic cash flow model to estimate how cost variability influences the cash flow. As a result, the improved ventilation system attains an additional NPVa ranging from 3.2 to 8.5 million US$ at the corresponding defined probability of 90%. The results of this study reveal that the developed risk analysis method can efficiently estimate the financial benefits of ventilation modelling and consider risk events and their total operational losses associated with use of the existing ventilation system. This approach provides a range of possible outcomes and helps with deciding whether the ventilation system is appropriate or whether it should be updated to better suit the project financial benefits.

Jun 3, 2020

By W. H. Yarroll Discussion by W. A. Griffith

W. A. Griffith (Head, Research Department, Phelps Dodge Corp., Morenci, Ariz.) - It is gratifying to see the increasingly common use of classical statistical procedures by metallurgical researchers. Mr. Yarroll has given excellent illustrations of the utility of multiple correlation analysis of complex metallurgical data. Our experience in applying these procedures to historical plant operating data has differed, however, from that which he suggests. The uninitiated frequently assume that the volumi-

Jan 1, 1969