Search Documents

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

By M Muzammil, S. Mukerjee, S. Saran, M. Bharathi

"This paper presents the results of in-situ tests conducted on a set of under-reamed piles in a silty sand deposit. Three piles (i.e. vertical, vertical with one bulb and vertical with two bulbs) of diameter 0.2 m were cast upto a depth of 5 m. The pile cap had four foundation bolts cast into it so that a mechanical oscillatormotor assembly could be mounted centrally on it. The oscillator-motor assembly was used to generate purely sinusoidal dynamic forces, in either horizontal or vertical directions. For both horizontal and vertical vibration cases, it was observed that (i) the natural frequencies decreased with an increase in the excitation force level, (ii) for the same excitation level, the natural frequencies as well as the maximum amplitude of vibration are almost the same irrespective of the pile geometry i.e. number of bulbs in the pile, indicating that the full pile length is not being excited. For the vertical vibration case, the soil-pile stiffness at frequencies, before resonance, were observed to be higher than those at frequencies after resonance. In the horizontal vibration case, the stiffness of the soil-pile system was found to be decreasing with an increase in the excitation force level. The damping ratio was found to be increasing with an increase in the excitation force level.INTRODUCTIONUnder-reamed piles are piles, normally upto a depth of 6 m, with one or more bulbs along the pile stem. These have been used for structures like transmission towers, structures on expansive soils etc. for a very long time, however it is only in the last 30 years that dynamic response of a pile has been studied. Evaluation of dynamic soil-pile interaction is a very complex problem as the conditions and properties of soil are highly variable and unpredictable. Various models and approaches have been suggested by various investigators for evaluating the dynamic soil-pile interaction problem, but most of them are based on the assumptions that the behaviour of soil is linear and the soil surrounding the pile is strongly adhered to it. But in practice, it is not so. The soil surrounding the pile is always somewhat loosened and undergoes some deformation when a sinusoidal load is applied. This causes the soil-pile system to behave nonlinearly.In earlier studies by Novak, (1974), Novak and Aboul-Ella, (1978) etc. a linear elastic behaviour of soil was assumed. This approach was very useful in understanding the mechanism of soil-pile interaction to a large extent. Subsequently various models were suggested like the lumped mass models with nonlinear discrete springs, dashpots and friction elements Matlock et al. (1978), weak cylindrical zone around the pile model Novak and Sheta, (1980), ideal boundary zone model with non-reflective interface, Han and Sabin, (1995) etc. These approximate solutions give an idea about the mechanism of dynamic pile-soil interaction to a large extent. However, in reality both separation and slippage can occur due to the formation of a weak bond at the contact surface between the soil and the pile when a dynamic load is applied. In addition, the soil column adjacent to the pile experiences large deformations under dynamic loads and thus behaves nonlinearly.Some computer aided model studies on the dynamic response of under-reamed piles have been reported, however, very few insitu dynamic tests on under-reamed piles are reported. Dynamic tests on piles were carried out by Novak and Grigg (1976) on small scale single piles and pile groups in the field. Similar field tests on small scale piles were conducted to study the nonlinear behaviour of a single pile and a pile group under strong harmonic excitation by Han and Novak (1988), Han and Vaziri (1992), Burr et al. (1997), Manna and Baidya (2010) etc. The majority of these experimental studies were focussed on the response of the specific pile groups and compared with the results of a single pile. Hence there was a need to study the influence of pile g"

Jan 1, 2015

Sandsloot open pit is situated on the northern limb of the Bushveld Complex, 250 km north east of Johannesburg, South Africa. Sandsloot is currently the largest open pit platinum mine in the world and is one of six potential open pits in the area. The geotechnical strength properties of the Platreef have posed significant mining and processing challenges to the PPRust operation since inception in 1992. In order to optimize the whole business as opposed to isolated cost centres a mine to mill initiative was embarked upon in 1997. Initial work focused on ore characterization and an entire suite of data was collected for each rock type. This included mineralogy, geochemistry, geotechnical, blast ability indices, as well as metallurgical strength data. The second phase involved the clear definition of customer requirements, namely the optimum performance criteria for the plant and mining departments. This involved extensive field trials and data capture to measure the interaction and influence of the mine to mill value chain. Once the design targets were defined, a 3D geotechnical model was constructed to ensure that the targets were consistently achieved. The model is very similar to an ore reserve model; however, it is populated with geotechnical, metallurgical and blast index data. Through software queries the appropriate blast powder factor for each mining block can be obtained, thereby ensuring the correct fragmentation is blasted for the plant and mining operation. The initiative has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. Additionally, the initiative has benefited both brownfield and greenfield projects on the PPRust operation

Jan 1, 2006

By P Goblet, S A. Séguret, E Cordier, A Galli

In salar-type deposits, lithium grades can be measured by bailers introduced at different elevations in the drill holes at locations where, later, the brine will be pumped out to recover the metal. When they are duplicated, these a priori rudimentary measurements may show large differences without indicating whether this is due to the procedure itself or to some physical causes linked to the dynamic behaviour of the salar (seasonality, rainfall, underground flow etc). In the reservoir presented in the paper, the problem is complicated by the double lack of stationarity of the lithium grades: the grades not only increase importantly with the depth but at the same time their fluctuations decrease, making it necessary to use non-stationary geostatistical techniques to simulate them. Reservoir simulation is developed in two steps: first, geostatistical simulations of the lithium grade create possible realisations of the reservoir; then, each geostatistical simulation is followed by a pumping simulation that calculates, at each drill hole of a given extraction scenario, the lithium produced each year over 40 years. For the set of 100 simulations produced in this way, a scenario reduction is made to choose the five most representative simulations where more complex calculations will be carried out (for example, changing hydrogeological parameters such as porosity and permeability, or the elevation of the filters, the number and the location of the pumping and the reinjection drill holes etc). The paper first presents an analysis of the geostatistical model sensitivity to the grade uncertainty when measured by bailer. Among the 100 measurements at our disposal covering the future production domain, 50 per cent are duplicates measured at the same place but at different times. They are randomly sampled to produce five subsets of 75 values, which will constitute the future 3D conditioning points for the geostatistical analysis and the simulations. For each subset, trend, standard deviation and variogram models are fitted, leading to five sets of 20 geostatistical simulations of grades. In this way, the reliability of the different parameters involved in the procedure is evaluated, as well as its impact on the pumping results. Then, a reconciliation study is conducted between the non-stationary nugget effects encountered in the 3D variograms of the lithium grade and a pure statistical analysis of 25 duplicates measured at different locations and/or different times. The result is that if the nugget effect reaches 20 per cent, which is the case of three conditioning subsets out of five, the reconciliation is good and the nugget effect of the variogram model represents the bailer uncertainty, ie the measurement error. Since the geostatistical simulation incorporates a nugget effect, it handles the bailer uncertainty and the impact on the produced metal is included in the evaluation. The final conclusion is that, after the hydrogeological pumping simulations, the initial differences between the five geostatistical models do not influence the final results: lithium grades measured by bailers can lead to a robust evaluation of the extractable resources, a conclusion that conflicts with conventional wisdom.CITATION:Séguret, S A, Goblet, P, Cordier, E and Galli, A, 2017. Bailer uncertainty evaluation in a lithium salar deposit, in Proceedings Eighth World Conference on Sampling and Blending , pp 395–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By A. H. Marquis

Since the start-up of its first Direct Reduction Module in April 1973, S1DBEC has produced over 2 million tons of prereduced iron. During this period, SIDBEC has acquired comprehensive experience in the operation of the direct reduction process and at the same time has learned to recognize the characteristics that the oxide should have to constitute an adequate feed for the process. A comparison is made as to the design and operation of the two direct reduction units now operating at Contrecoeur, Que. A description is given of a method of evaluation of a direct reduction unit, which takes into account the main process variable sand which permits comparison ofthe results on a daily basis. The paper defines the characteristics that the iron oxide and the prereduced iron pellets must have to meet the specific requirements of the direct reduction and the electric arc furnace processes. A simple model makes possible a rapid evaluation of the technical and economic effect related to the use of a given raw material. Finally, the paper outlines the advantages of prereduced iron in the steelmaking process and on the quality of the steel products.

Jan 1, 1979

By J Mar·n, R Anderson, S Strohma, R Harvey

Xstrata is the operator of both Minera Alumbrera Ltd (50 per cent Xstrata, 50 per cent Wheaton River) and Ernest Henry Mining Pty Ltd, (99.99 per cent Xstrata), both copper-gold deposits, using conventional SAG/ball milling at current capacities of 36 Mt/yr and 10.3 Mt/yr respectively. Alumbrera is located in Catamarca Province, in the north west of Argentina. Ernest Henry is located in Cloncurry, north west Queensland, Australia. Both operations started in late 1997, with commercial production achieved in early 1998. Different designs and equipment are in use for both operations, however the evolution of SAG milling performance, although logically related to their specific features, reflect similar trends of consistent increases in throughput. This paper will discuss the main changes to the SAG mill liners in both operations and the results achieved to date. A summary of the operating strategies will be included.

Jan 1, 2003

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

By D. S. van Vuuren

Titanium bearing resources can selectively be chlorinated at temperatures below 200°C if the Ti02 in the feed is nitrided before chlorination. However, the nitriding reaction is highly endothermic, requires highly reducing conditions, is only thermodynamically favourable at elevated temperatures, and is affected by mass and heat transfer restrictions. At the required processing conditions, problems might also be experienced with sintering and with melting of slag forming components in the raw materials. A test programme was undertaken to study the effects of raw material type, temperature, gas composition, bed depth, carbon to raw material ratio and residence time in order to simulate conditions required for scaling up a nitriding process. In contrast to previous experience with low-grade titanium-bearing slag containing about 30% Ti02, ilmenite and chlorinateable slag do not form melting phases under the studied nitriding conditions and hardly sintered at all. Both feed materials can readily be nitrided with conversions in excess of 90% at temperatures around 1300°C and using bituminous coal as reducing agent with fixed carbon in excess of 1.1 times the stoichiometric requirement. The conversion decreases as the bed depth of the feed material increases and the N2/CO ratio in the gas decreases. Analysis of the relative rates of mass and heat transfer into the reacting beds of ilmenite and slag showed that the heat transfer rates are more limiting than the mass transfer rates. In order to increase the throughput that can be achieved in a kiln, it would be necessary to take special measures to enhance the heat transfer rates into the mass of reacting material. One such a measure is to pre-form the mass of reacting material into thin-walled, hollow brick shapes prior to introducing it into a kiln. Depending on bed depth, temperature and N2/CO ratio, required residence times in the high temperature zone of the kiln can vary between about 6 and 10 hours. Keywords Titanium dioxide, titanium nitride, carbo-thermic, reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004

By Porter W. Shimer

(New York Meeting, February, 1912.) IT does not seem to be generally known that some American pig-irons contain notable amounts of vanadium, and while the present investigation is far from covering the whole range of irons, it is hoped that, at least, it may serve to call attention to the importance of looking for this element. The majority of the pig-irons investigated were made in the Lehigh Valley and neighboring furnaces, using more or less New Jersey magnetite in their mixtures. Many of these ores, and probably all of them, contain a little vanadium as well as titanium; the ore from one of the largest of these mines contains 0.05 per cent. of vanadium and 0.60 per cent. of titanium. Dr. Thomas M. Drown was the first to detect the presence. of vanadium in the incrustations 1 occurring on certain pig-irons, and he also found this element in a number of magnetites, but the methods for its accurate determination had not, at that time, been well worked out. In a general way, it may be said that the Lehigh Valley pig-irons contain from 0.02 to 0.05 per cent. of vanadium and from 0.10 to 0.20 per cent. of titanium. These elements follow the silicon; that is, the furnace-conditions which produce a high-silicon, low-sulphur iron will cause the maximum reduction of vanadium and titanium, and the lower grades of iron, with low silicon and high sulphur, have a lower content of these elements. The following analyses of irons made from the same mixture, but under varying furnace-conditions, show this very well Vanadium. Silicon. Sulphur. Per Cent. Per Cent. Per Cent. NO. 1 X, . . . 0.042 3.46 0.022 No. 2 plain, . . 0.038 2.26 0.041 Mottled, . . . 0.0'29 0.52 0.106 1 Robertson and Firmstone, Note Concerning Certain Incrustations on Pig Iron,Trans., xii., 641 (1883-84).

Aug 1, 1912

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By Howard W. Wainwright

The Bureau of Mines is engaged in a research program on the characterization of tars produced by low-temperature carbonization of coal and their economical upgrading to more valuable materials, Throughout the years, hydrogenation has played an important role in the treatment of these tars, mainly as a means of converting the whole crude tar or selected fractions to motor fuels; diesel oil, lubricating oil, or various solvents. In some instances, production of specialty chemicals has been the objective. The purpose of this report is to summarize, without critical review, the information of the past 25 years on the hydrogenation of low-temperature tars and related substances as presented in the literature or its English translation. Published articles and patents not abstracted in the main body of this report are included in a bibliography at the end. HYDROGENATION REACTIONS The hydrogenation of tar follows three general types of reactions; 1. The removal of oxygen, sulfur, and nitrogen in the tar to form water, hydrogen sulfide, and ammonia, respectively: [ ]

Jan 1, 1961

By R. L. Marovelli

ANTICIPATING the eventual use of the huge tonnages of nonmagnetic taconites of the Mesabi range of the United States, the Federal Bureau of Mines is classifying and evaluating these deposits in detail. This introductory report describes work begun in 1954 as part of a long-range program to sample, classify, and evaluate important occurrences of nonmagnetic taconite on the Mesabi, range. Included in this report are brief discussions of the geology, history, and potential of the Mesabi range district and mining industry, together with a more detailed presentation of the sampling and metallurgical evaluation of these nonmagnetic taconite deposits. A total of 898 field samples was collected. Most of these were taken in the region between Grand Rapids and Chisholm, Minn., but a few came from the area between Chisholm and Buhl, Minn. Of the total samples, 865 were from open pit bank faces where the greater vertical distances presented by the cherty members facilitated the taking of a large number of samples. Conversely, the narrow face presented by the slaty members confined and limited the areas from which samples were taken. In addition, 33 of the field samples were taken from rock dumps in order to determine, in a preliminary way, the characteristics of these materials.

Jan 1, 1961

The 1965 Lignite Symposium, the Louth in a series and the third sponsored by the University of North Dakota and the Bureau of Mines, was held at Bismarck, N. Dak., on April 29-30, 1963. These symposia provide a forum for those interested in the technology and utilization of solid fuels, especially lignitic coals. As part of the meeting, a 200-mile field trip was taken including; inspection of (1) the 200-megawatt, pulverized lignit-fired Leland Olds plant of Basin Electric Power Cooperative, under construction near Stanton, N. Dak.; (2) the site of the Glunharold mine of the Truax-Traer Coal Co., Division of Consolidation Coal Co., where a wheel excavator was being assembled; (3) the operating Beulah mine of Knife River Coal Mining Co., subsidiary of Montana-Dakota Utilities Co., near Beulah, N. Dak.; and (4) the 400-megawatt, hydroelectric Garrison Dam powerplant, near Garrison, N. Dak.

Jan 1, 1966

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

Common practice in mineral resource estimation consists of partitioning the orebody into several domains defined by grade intervals, prior to the geostatistical modelling and estimation/simulation at unsampled locations. This paper shows the pitfalls of grade domaining through a case study in which we compare the performance of several estimation schemes and demonstrate that the use of domains defined by grade cut-offs implies a deterioration of the resource estimates, mainly in what refers to precision and conditional bias. Then, several conceptual limitations of the grade domaining approach are stressed, in particular the fact that it does not account for the spatial dependency between adjacent domains and for the uncertainty in the domain boundaries. Also, this approach is shown to be sensitive to the cut-offs that define the domains, to provoke artifacts in the kriging maps, histograms and scatter grams between true and estimated grades, and to lower the kriging variance, a feature that may impact the mineral resource classification. An alternative approach is finally proposed to overcome these limitations, based on a stochastic modelling of the grade domains and a co-kriging of the grades using information from all the domains. Keywords: geostatistics, kriging, conditional bias, geological control, grade zoning.

Jan 1, 2005

By K. L. Boyd

"Can the increasing tonnages of ore and waste mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each stage of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in material handling from the mine to the mill, maximizing operating hours per year.RÉSUMÉ Le recours à des concasseurs plus grands et plus performants suffit-il à gérer l’augmentation du tonnage du minerai et des déchets que l’on extrait de nos jours ? Cet article examine les tous derniers modèles de concassage primaire et de grands concasseurs à cône. Il montre que, pour satisfaire aux exigences de production plus conséquente des exploitations minières existantes et nouvelles, il est important d’optimiser les taux d’utilisation à chacune des étapes du circuit de réduction de la taille des roches, en plus d’utiliser les concasseurs plus grands actuellement disponibles. L’objectif de cet article est d’aider les sociétés d’experts-conseils et les exploitants à sélectionner le meilleur équipement ainsi que des articles fabriqués sur mesure pour la manutention de la mine au concentrateur, en optimisant les heures d’exploitation par année.INTRODUCTIONAre larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications have since become available.The rock size reduction process from the mine to the selected milling process facility has not changed since a person first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages:• stage 1: mining (rock breakage and fragmentation);• stage 2: prescreening (scalping);• stage 3: primary crushing; and• stage 4: fine crushing (secondary, tertiary, and quaternary).Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments play a key role in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit."

Jan 1, 2017

By G. D. Buson

Driefontein Consolidated Limited has a proud history in the South African gold mining industry dating back to March 1945 with the formation of the West Driefontein Gold Mining Company. The reclamation gold plant at West Driefontein was originally built as a uranium recovery plant in 1970. With the collapse of the uranium oxide yellow cake market, the uranium plant was closed in 1988and successfully converted into a gold plant, recovering gold from repulped tailings dams1. The West Driefontein Reclaim plant utilized milling, leaching, conventional rotary vacuum filtration and cementation to recover the gold at a rate of 200,000 dry tons per month. The No. 1 tailings dam (at a head grade of 0.8 Au g/t) began to near the end of its life during 1996, and the next slimes dams to be treated, the No. 2tailings dam (at a lower head grade of 0.56 Au g/t) was found too marginal for reprocessing using the filtration technology. Alternate technologies were investigated, particularly the carbon-in-pulp (CIP) plant based on the Anglo-American Corporation (AAC) pump-cell technology at the Vaal Reefs Exploration and Mining Company?s East gold plant which was operating profitably at lower head grades2. The AAC pump-cell technology is based on the carousel mode of operation2. The suitability of CIP technology for the West Driefontein Reclaim plant was investigated using a pilot plant pump-cell supplied by Kemix The data gathered were utilized in sizing a full scale AAC pump-cell plant. This plant was motivated, built and commissioned on the 22nd of November 1996. Incorporating 6 eighty cubic metre AAC pump-cells. The West Driefontein Reclaim plant initially treated repulped slimes dam material. A subsequent change of feed material to current arisings (from the main gold plant) occurred in1997 in order to convert mills for waste rock treatment. Currently the reclaim plant treats a combination of current arisings and waste rock (milled at the reclaim site). The new CIP plant replaced twenty-seven rotary vacuum filters. A comparison between the filters and CIP in terms of operating costs was undertaken, as well as a performance analysis of the CIP plant to determine its flexibility in terms of variation of the throughput, pulp density, gold input, leaching efficiency prior to CIP, and the rate of carbon movement.

Jan 1, 1999

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009

By Gerhard Lang

"Slurry Microtunneling is a well-established technology building on over 20 years of experience in successful tunnel installations under all kinds of soil conditions across the U.S. and Canada. Recent microtunnel installations prove that initial hesitation, e.g. curved drives, is fading and long-distance pipe jacking projects as well as lake outfalls are being considered. One of the younger technologies is Direct Pipe®, which combines the benefits of HDD and Slurry Microtunneling. It fits exactly into the area where HDD is not feasible or too risky to apply. The paper points out the benefits of the Direct Pipe® technology for owners, engineers and contractors and discusses the latest developments of Slurry Microtunneling for long-distance, curved drives and sea/lake outfalls with wet recovery of the equipment such as on the ‘Keswick Outfall Project’ in Ontario. The first Direct Pipe® installation in the US was executed in August 2010. Since then, another 22 crossings have been carried out amongst a total of more than 60 Direct Pipe® crossings worldwide. INTRODUCTION Pipelines installed underground are indispensable for supplying the growing world population with water, oil, gas and electricity, for removing wastewater and for providing functioning telephone and communications networks. During recent years the limits of trenchless applications have been permanently shifted, leading to higher and more stringent project requirements and consequently new technologies, either as further development of existing methods, or through the development of new methods by incorporating elements of proven technologies. MICROTUNNELING TRENDS IN NORTH AMERICA Slurry Microtunneling has a wider geological application range in comparison to EPB and hard rock Microtunneling. The Slurry MTBM can be equipped with specific cutting wheels to cope with different soil conditions. The most flexible and most often employed type is the mixed soil cutting wheel, which contains a mixture of disc cutters as well as scrapers for varying soil conditions from cohesive soils (clay, silts) to highly permeable soils including sands, gravels and cobbles and even hard ground formations such as rock and boulders. A detailed geotechnical report provides the appropriate data to configure the MTBM and its features to the ground conditions expected. Mixshield or hydroshield (AVN/AVND) MTBMs in particular, can be safely operated with little overburden (~ 3-5 x machine diameter) and minimum risk of frac-out or settlement on the surface. This is especially beneficial in urban areas with sensitive buildings or for river crossings with protected fish habitats."

Jan 1, 2016