Search Documents

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By K. Wongaew, R. F. Cook, J. E. Carlson, T. Cleys, C. R. Smith

Steel fiber reinforced concrete segmental rings are the final tunnel lining for approximately 85% of the alignment for a 6.706-meter (22-foot) internal diameter tunnel being built as part of the East Side Combined Sewer Overflow Tunnel Project. This paper describes the approach adopted for the design of the steel fiber reinforced concrete segments, the development of the performance criteria for the segments, and the testing program used to confirm the performance of the materials and segments in the laboratory and in the field.

Jan 1, 2007

By Ying Lu, Jeffrey C. Johnson, Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Energy dissipation and fragmentation of rock is of interest for mine-to-mill operations in order to understand breakage and to minimize energy consumption during blasting at the mine site, and comminution at the processing plant. In this regard, high velocity impact breakage of long granite cores, called bars, has been studied with instrumented strain gages to follow the energy dissipation gradient along the bar length resulting from the strain waves generated by impact. As a result of high velocity impact, three zones have been identified (fragmentation, fracture, and elastic) and these three zones have been characterized in 3D using X-ray tomography. The fragmentation zones of the granite bars were studied in detail to describe the particle size distribution and the particle shape characteristics. Finally, the experimental energy dissipation for the fragmentation zone was found to be in close agreement with the expected energy calculated from the Bond work equation, if the anisotropic granite particles are defined by length rather than by sieve size.

Les Mines Inmet ? La Division Troilus exploite une mine d?or à ciel ouvert depuis 1996 et produit un concentré de cuivre. La Division Troilus est localisée à 175 KM au nord de la ville de Chibougamau? au 51 parallèle.

Feb 1, 2008

By Walter Smith

Environmental Quality Committee ?EQC was created in 1995 to facilitate dialogue between industry and northern communities and help build the understanding of the industry in those communities. ?EQC is made up of representatives from 32 northern communities. ?Meet regularly with Cameco to discuss on going and new projects. ?Tour mine sites on a yearly basis.

Nov 1, 2011

Organization Place Date 1919 American Railway Engineering Association Chicago, 111. Mar. 18-20 Society of Industrial Engineers New York, N. Y. Mar. 18-21 American Electrochemical Society New York, N. Y. Apr. 3-5 National Foreign Trade Council Chicago, Ill. Apr. 24-26 American Iron and Steel Institute New York, N. Y. May American Institute of Electrical Engineers Lake Placid, N. Y. June

Jan 3, 1919

By Maryam Sadeghi, Jonathan Roy, Claude Bazin

"The operation of mineral processing equipments is intimately related to the mineral composition of the ore. However unit performances are usually characterized in terms of metal contents or recoveries as this data is easier to obtain than the mineral contents. This paper describes a method that combines the operations of material balancing and estimation of the mineral contents of the ore. The estimated mineral contents can be used for process analysis and diagnosis of operating problems.IntroductionThe ore that is feeding a concentrator is made of minerals that condition the energy requirements for the ore comminution and the performances of the subsequent separation circuit. Indeed a change in the mineral composition of the ore may lead to lower grinding mill throughput as well as lower recovery or grade of the economical products. Despite this relationship is recognized the mineral composition of the ore is seldom measured or estimated to provide regular information for the diagnosis of operating problems. Some methods such as the QEM-SCAN (Whiten, 2008; Lamberg and Vianna, 2006) are available to measure the concentration of the minerals in ore samples but the method is time demanding and plant operators usually base their evaluation of the plant performances on chemical assays of metals or elements since this data is easier to obtain from ore samples.Usually samples of the streams of mineral processing plants are collected on a daily basis to be assayed for strategic elements. The obtained concentrations are balanced to produce coherent data with the material conservation constraint and then used to characterize the day to day operation of the plant in terms of recovery of valuable metals and grades of the marketable concentrates. The behavior of contaminant elements can also be monitored from this data allowing the operators to explain for instance a lower zinc concentrate grade by a more important contamination of iron. However such diagnosis is only partial as the contaminant element can be transported by different minerals. Indeed the iron contamination of a zinc sulfide concentrate may be caused by an inadequate depression of pyrite or due to another iron carrying mineral. A possible way to answer the question is to determine the concentrations of the various minerals in the ore and produced sealable concentrates. Since measuring the mineral contents of the ore could be a demanding task one should consider to estimate this data from the daily chemical assays of the sample collected on the main streams of the circuit. Some authors have already investigated the problem. Whiten(2008) described a method to estimate the mineral contents of an ore sample. Lamberg and Vianna(2006) proposed a method to do a sequential mineral reconstruction followed by a material balance. Few of these methods account for the mass conservation of the reconstructed mineral contents."

Jan 1, 2016

Using a cylindrical hydrocyclone with a long vortex finder as the separator, a batch sizer was developed for the fast comparative sizing of the coarse solids normally encountered in mineral pulps.Operating times as short as 2 or 3 min gave separations ranging from 16 mesh down to the subsieve sizes.Reproducibility was good and sensitivity was adequate for most applications.

Jan 1, 1968

By Bernard H. Hertlein

All methods of deep foundation construction present challenges to the contractor and engineer that vary according to the method employed, and the geotechnical conditions in which it is being used. Augered-Cast-In-Place (ACIP) piles are generally regarded as one of the most challenging, because the construction method precludes the use of traditional shaft inspection and quality control techniques. Application of Nondestructive Test (NDT) methods can provide quality control for ACIP shafts that traditional methods cannot, but each NDT method has limitations. These make some NDT methods unsuitable for use on ACIP shafts, and may limit the effectiveness of others, depending on geotechnical conditions. To help contractors and engineers working with ACIP piles select the test method most appropriate to specific site conditions, this paper presents a summary of the major NDT methods currently available, and reviews their capabilities with respect to the unique conditions presented by ACIP pile construction. Case histories illustrate how a combination of careful method selection, skilled data interpretation, and experienced engineering judgment have resolved problems and ensured quality in foundation construction by discriminating between potentially serious defects, and those that are unlikely to be significant.

Jan 1, 1997

By J. Kulas, J. Weaver, K. Hagley

An assessment of potential groundwater movement beneath the tailing impoundment at the Red Dog Mine was performed, and has indicated a unique aquifer situation within sub-permafrost groundwater at the site. The aquifer was shown to be isolated from both vertical recharge and a real discharge, and is characterized as a virtually no-flow system. The permafrost resulted in a deep aquifer with high tidal efficiency, meaning that variable surface loads are easily transmitted to the fluid. The tidal efficiency has been characterized through analysis of water level fluctuations that respond to earth tides, barometric pressure loads, and loading from the pond.

Jan 1, 2002

By Albert L. Toenges

[During the past few years there has beer trend away from locomotive haulage of coal from the loading point to the preparation plant of bituminous-coal strip, miner to motorized. haulage. The question has arisen whether this is always economical, and the purposes of this investigation is to determine, if possible the economic limit for motorized haulage. The operators of strip coal mines and of open-pit ore mines have shown great interest in this problem, and it is thought that the findings of this investigation will. Provo helpful to them.]

Jan 1, 1938

By Leonello Sciacca

Deepening of harbours has become a priority, necessary to the ongoing operation of the wharves in the face of deeper draft merchant vessels and cruise ships. It is now standard practice in many areas to provide for harbours to be dredged to significant depths below mean sea level, in the order of 12.00 m (39 ft) for existing berths and 15.00 m (49 ft) for new wharf construction. The Ravenna Port Authority initiated a project to deepen the harbour bottom at selected wharves to a depth of 12.00 m (39 ft). In preference to reconstruction of the wharves with longer and heavier sheet piling or other equally disruptive reconstruction, they identified the structural reinforcement of the existing wharves by means of deep underwater tie rods as a possible alternative cost-effective solution. Having defined the design concept, effort was concentrated on developing the required technology. A technique, already in use for the installation of tie rods by means of robotics, was identified as potentially suitable for underwater use. It was decided to carry out the fine tuning and the evolution of the technology for a marine environment of the robot unit and of the related remote control software that controls the installation of the tie rods. An experimental test site was set up to refine the drilling, installation, grouting, monitoring and testing of underwater tie rods. The purpose was to confirm the feasibility of the proposed solution and the reliability of these tie rods for use in the reinforcement and construction of wharves. The paper also discusses the theoretical and experimental study of underwater tie rods dealing with the theoretical analysis of the interaction between tie rod and soil, aimed at identifying the correlation between the forces of applied traction and the corresponding measured elongations. A series of tests were carried out with positive results, both at the operating load of 300 kN (67 kips) and at the nominal maximum load of 630 kN (142 kips). The tests were carried out on seven tie rods, of which three were installed at a depth of 5.00 m (16 ft), principally to test the reliability of the operating and remote control systems in the presence of a significant hydrostatic pressure, and four were placed at a depth of 8.00 m (26 ft) to check the load bearing capability of the tie rods positioned at the depth called for by the current project.

Jan 1, 2011

By F. Z. Suo

Baoahan Iron and Steel Complex is situated at lower beaches of the Yangtze River. The subsoils 50~70 M below the surface is a deposite of Yangtze River delta, consisting mainly of weak silty clay and loam, with low soil bearing capacity. Consequently, to build on such a weak soil a grant iron and steel integrated works weak soil improvement at the Complex, pile foundation is the effective type. It is estimated that at the first stage of Baoshan project 60,000 piles have been driven, of which 60% are steel pipe piles and 40% reinforced concrete piles. To provide reliable basis for pile foundation design, on-site loading tests were carried out for long reinforced concrete piles 27,45 60 M in length ,with strain gauges on the chief reinforcement of pile shaft and strain rod on pile tip. Based on loading tests, the paper discusses and analyses some issues, including determination of load transfer mechanism distribution of frictional resistance. Tests show that as far as long friction piles in soft clay are concerned, regardless of the properties of pile tip's bearing stratum, loads are mainly carried by shaft frictional resistance which it is effective to determine pile capacity in terms of P ~ S relationship.

Jan 1, 2010

By Quin Dennis

Process Optimization ?What is it really? It is NOT ?a larger fan to increase draft through a process ?a larger pump on a wet circuit ?a wider conveyor belt for solid materials ?a larger feed elevator into or out of a process These relieve individual constraints ??bottlenecks??and allow operation to the next constraint in the process ?It is also NOT about automating the operator ?which captures consistency but is not continuous optimization

Nov 1, 2011

By Jochen Belz, Allan Henneker, Nod Clarke-Hackston

For the construction of tunnels and other underground structures, extraction of the exact amount of material is of paramount importance both economically and for engineering purposes. In the Sequential Support Method (NATM) immediate (sequential)and smooth support by means of shotcrete, steel arches, lattice girders and rockbolts, either singly or in combination are used; cutting of the precise (albeit sometimes of complex geometry) profile is an integral part of the method. In order to save unnecessary excavation and provide better information to the machine operator, VMT GmbH has developed a system to support precise excavation of the tunnel profile when using road headers or other partial face cutting machines. This paper outlines the principles of this system with examples from Australia, Ger-many, Sweden and Spain and will cite examples of typical savings achieved.

Jan 1, 2007

By Gerald T. Homce, James C. Cawley

Electrical arcing injuries are the most common form of electrical injury in mining. MSHA data show that 381 "non-contact electric arc burn" injuries occurred in the mining industry from 1996 - 2005. A more detailed study of data from 1990-2001 showed that five types of apparatus - circuit breakers, conductors, nonpowered hand tools, electrical meters and test leads, and connectors and plugs were involved in two-thirds of the lost workday injuries. Many of the protections from electrical arcing injury available to workers in other industries stem from the application of National Fire Protection Association Standard 70E - Standard for Electrical Safety in the Workplace (NFPA 70E). NFPA 70E is a generally accepted industry guideline document, but excludes underground mining from its scope. Many of its practices and procedures, however, can be applied in the mining workplace to supplement the existing electrical safety requirements of Title 30 Code of Federal Regulations. This paper describes how NFPA 70E can be applied to mining workplaces after an analysis of the mine power system electrical arcing hazards has been completed (and Hazard/Risk Categories determined) using the tables from NFPA 70E or the calculation method as described in IEEE 1584. NFPA 70E can then be used to determine the levels and types of personal protective equipment (PPE) needed to protect miners against burn injuries. Appropriate lockout and tagout (LOTO) procedures for use in the mining industry are also described. Suggestions for better selection of electrically-rated hand tools are included. Recommendations for electrical meter selection and use based on transient withstand capability are also discussed.

By W. A. Tiller, J. D. Harrison

HOT pressing of powder particles has gained importance recently, since it affords a method in which high densities are rapidly attained. In a recent study on hot pressing of alumina powders, Mangsen, Lam-bertson, and Best1 have shown within the limits of their experiment, the validity the rate equation for densification in hot pressing, originally proposed by Murray, Livey, and Williams.2 i.e., where D = fraction of theoretical density, t = time, P = pressure and 77 is the viscosity, all in appropriate units. This equation was derived from earlier work of Shuttleworth and Mackenzie3 which is based on the closing of spherical pores under the action of surface tension. The integrated form of this equation yields a straight-line relation between log (1 - D) and t. Such conditions were found by Felten4 to be true only after extended periods of pressing. In an endeavor to quantitatively evaluate the exactitude of this equation in the initial sintering stage, i.e., prior to sealing of the pores, spherical anti-

Jan 1, 1962

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By Michael B. Cortie

Mesoporous gold sponge has the unique property of being both metallic and highly resistant to oxidation. It has potential application in catalysis, in bio-sensors, in optical coatings, in analytical chemistry and, as we show here, as the basis for a new kind of ultra-capacitor. Due to the cost of gold, the most probable niche for a gold-based ultra-capacitor would be in the high-power/high-energy regime, a region where gold would compete with devices based on RuO2. A high internal resistance limits the power that can be usefully drawn from existing carbon-based ultra-capacitors, and that this problem can potentially be overcome by gold-based devices. A simple proof-of-concept ultra-capacitor based on mesoporous gold is described and its behaviour during charge and discharge cycles examined. In this work a step change in the input or output voltage of the device was used as the controlling parameter. There was also a residual faradaic current resulting from traces of undissolved aluminium left over from the AuAl2 precursor used to make the sponge, and some charge storage due to polarization of the solution. Deconvolution of these three effects was not entirely accomplished, but an ostensible capacitance of about 7 to 14 mF/g Au was demonstrated. Further improvement from these early results seems likely.

Oct 1, 2003

bauma 2004 will feature a couple of firsts for one of the world’s largest construction and building materials machinery exhibitions. The event is scheduled for March 29 through April 4 of next year at the New Munich Trade Fair Center in Munich, Germany. For the first time, bauma will feature an exhibition area dedicated to mining equipment and technology. Also for the first time, the Commonwealth of Independent States (CIS) will be a partner region of bauma.

Jan 1, 2003